Search Documents

By M. Matema

Paper written on project work carried out in partial fulfilment of BSc (Eng.) Metallurgy and Materials Engineering Small and large welded aluminium specimens were tested in fatigue and the results compared with design curves for aluminium in specification BS8118. Metallurgical tests were also performed on the specimens in order to correlate microscopic and macroscopic phenomena. The small-scale fatigue test results were in reasonable agreement with results in BS8118, whereas the large-scale fatigue tests showed that BS8118 is conservative.

Jan 1, 2005

Splashing and wave formation has been studied experimentally by using one-seventh water model of CLU (Creusot-Loire Uddeholm) reactor with two different tuyere configurations by using paraffin and water as simulated slag and simulated metal respectively. Experimental results have been discussed in terms of total splash volume, relative slag volume in splash (dispersed-slag phase holdup in splash), wave frequency and wave amplitude with respect to gas injection rate and tuyere configuration at bath heights between 0.25m and 0.38m. Gas flow rates ranged from 0.00599m3/s to 0.01312 m3/s. The results of splash measurements showed that splash volume increased with increasing gas flow rate and decreasing bath heights for both tuyere arrangements. However, off-centre configuration resulted in relatively higher amounts of splash. The slag volume in splash (Dph in splash) was also found to increase with decreasing bath heights and increasing gas injection rates. The high speed photography revealed that the frequency and wave amplitude increased with gas injection rate. The experimental results also showed that the frequency and vertical displacement of the rotating wave increased when the tuyere orientation became off-centered. This might be used to explain why off-center configuration resulted in generating higher splash volumes than the center configuration.

Jan 1, 2004

By Steve Kral

The concept of sustainable development is not new to the mining industry. Many people involved with mining have argued that the industry throughout the world has always supported the communities where they operated. They say that the mining industry was employing sustainable development practices before the phrase became fashionable. The mines employed residents and supported the local economy through tax payments and the purchase of goods and services from local businesses. In many cases, mining companies have built medical facilities and contributed money, equipment and services to local schools. In modern times, mining companies have donated reclaimed land to the local communities for use as parks and recreational facilities.

Jan 1, 2004

By J. Evans

Including: Tailings thickeners, CCD?s, paste thickeners, HI-rate thickeners, lamella thickeners, high compression thickeners, clarifiers etc. Flocculant dosing control for mining thickeners and clarifiers is influenced by a number of process factors. 1. Flow rate into the thickener or clarifier a) As the flow rate increases into the thickener or clarifier ?retention time? decreases which causes a greater affect hydraulically on the settling solids. So as the flow rate increases it will generally mean an increase in flocculant dosing rate. b) As the flow rate decreases into the thickener or clarifier the retention time increases which reduces the hydraulic affect on settling, improving settling rates. This will generally mean that as the flow rate decreases, we will decrease the flocculant dose rate.

Jan 1, 2011

By R. Karl Zipf, Kousick Biswas

The main objective of occupational health and safety research is to minimize or eliminate the events that may cause fatal or non-fatal injuries to human workers. A commonly used technique is to devise an “incident prevention plan”, which is more often the product of thorough investigations of past reported incident events. Incident documentation and methodical reporting and systematic and thorough data collection, often help identify the root cause of the incident – in other words, the etiology of the incident. These retrospective analyses of the incidents can efficiently identify the future steps to take to achieve the objective of minimizing occurrence of “events of interest”. This paper introduces a novel technique – “Taxonomic Analysis”, which identifies the root causes of an event (an incident in this case) and can provide future direction for corrective measures to reduce the probability of occurrence of the event. A taxonomic analysis involves systematic and organization of data based on observation, description, and classification. This paper utilizes the rock fall related incident narratives, available with the Mine Safety and Health Administration (MSHA) database (1984-1999), for a taxonomic analysis. The study found that 67.6% of groundfall incidents occurred in supported areas with the remainder (32.4%) in unsupported areas. Some form of rock mass failure appears to cause about 50% of groundfall incidents, although in 39.7% of the overall groundfall incidents or two-thirds of those involving rock mass failure, the exact nature of the rock mass failure could not be determined from the narratives. Human activities factors such as scaling or barring down, drilling or bolting, and setting timbers or cribbing accounted for another 34.5% of the groundfall incidents. Finally, support system failures made up the remaining 15.5%. Results from this taxonomic analysis may suggest focus areas toward which preventive measures and future research activities could concentrate.

By Nabil F. Ismael

The axial capacity of step tapered bored piles in sand was examined by field tests at one site in Kuwait. Two straight piles, and two step tapered piles were load tested in compression to failure. All four piles were 3 m deep. The straight piles were 0.2 m in diameter. The step tapered piles had a diameter of 0.3 m for the upper segment which extended up to 40% of the pile length changing to 0.2 m diameter for the lower section. The soil profile consists of medium to dense sand with minor cementation and no groundwater was encountered. Both the ultimate bearing capacity and the settlement at working loads were examined. The axial capacity of the step tapered piles was greater, and the settlement at working loads was less, compared with the straight shaft piles. The increase in capacity is mainly attributed to the added side friction along the larger diameter top segment of the shaft.

Jan 1, 2008

By Michael G. Zabetakis

Limits of flammability of normal propyl nitrate (NPN) vapor were investigated at ambient and elevated temperatures. Minimum spontaneous ignition and decomposition temperatures were determined with laboratory apparatus over the pressure range from 0 to 4,000 p.s.i.g. Flame speeds and the detonation susceptibility of NPN vapor were measured at elevated temperatures. Stable detonation was obtained with liquid NPN at elevated temperatures, and the detonation velocity was determined to be between 4,700 and 5,100 m./sec.

Jan 1, 1962

By W. P. Johnstone

The computer assisted generation of geological models to represent the geometry of, and grade distribution within, orebodies is a rapidly growing area of the geological profession. Such models are increasingly used as a necessary starting point in determining the mineability of mineral deposits in terms of practical mine design and economic considerations. The transition from traditional techniques such as field or underground mapping and the manual calculation of grade and tonnage estimates, as well as related activities such as the interpolation of cross-sections, the use of stereographic projections, core logging and hand contouring, to computerized applications, is by no means complete. In fact, many geological professionals deliberately avoid the use of computer simulations based on the perception that the resulting models are simplistic and that their construction is not founded on sound geological principles. The purpose of this paper is to assess current thinking on this topic by considering; (a) an overview of advances in the drafting of geological maps, (b) the theoretical basis for multi-dimensional geological modelling, (c) the case for combining traditional and modern techniques, and (d) the benefits to the mining value chain.

Jan 1, 2003

MFIRE is a computer simulation program that performs normal ventilation network planning calculations, and dynamic transient state simulation of ventilation networks under a variety of conditions. The program is useful for the analysis of ventilation networks under thermal and mechanical influence. MFIRE simulates a mine's ventilation system and its response to altered ventilation parameters, external influences such as temperatures, and internal influences such as fires. Extensive output enables detailed quantitative analysis of the effects of the proposed alteration to the ventilation system Network simulation using digital computers has become widespread throughout the mining industry in recent years. However, as the sophistication of the simulator increases (MFIRE, for example), the complexity of input data requirements and interpretations of results requires more skill and knowledge from the users. Perhaps the most difficult part of using MFIRE is to construct the data set describing the mine's physical layout and its ventilation properties. The initial attempts to get the data set running often reveal unknown or ignored aspects of the mine's ventilation. MFIRE was written in Fortran 77 and compiled with Microway1 Fortran for the Intel 80386 based computers with a 80387 math co-processor. The source code is portable and available for users who wish to modify the source code to operate on other computers. This user manual describes the development of MFIRE, the input format and requirements, the output, common errors, fire parameters, and examples MFIRE application. Valuable reference material is included in the appendices. Knowledgeable users may skip directly to the PROGRAM INSTALLATION AND OPERATION section to begin using MFIRE immediately.

Jan 1, 1995

By J. A. Bakken, M. Tangstad, P. A. Eidem

In the submerged arc production of ferromanganese, sillicomanganese and ferrochromium, the coke bed characteristics play an important role. The basic mechanisms of electric current conduction in the coke be dare not yet fully understood, but important parameters are the material resistivity of coke and the contact resistance between the coke particles. Preliminary tests indicate that the contact resistance is of great importance to the bulk resistance of the coke bed. An apparatus measuring the material resistivity and contact resistance of carbon materials has been developed. Both graphite and industrial coke have been tested. The material resistivity tests were performed on single particles to ensure that the effects of pores and cracks were included and the contact resistances were excluded. Two geometries were tested to obtain the contribution of the contact resistance to the total resistance of two connecting particles. The tests were performed in an inert atmosphere at temperatures and current levels found in industrial submerged arc furnaces. The results show that the method has a satisfactory reproducibility. It was found that the contact resistance is about 10 times higher than the resistance of the material when two particles are in perfect contact and that the resistivity of SSAB coke is more than 10 times higher than that of the graphite at room temperature, but with increasing temperature the difference decreases. For SSAB coke the general trend is that both the resistivity and the contact resistance decrease with increasing temperature.

Jan 1, 2007

By D. J. Adams, W. K. Rymon-Lipinski

Rock engineering plays a crucial role in contributing to sustainable development in South African mining. A framework for this has been created through legislation and structures to encourage the mining industry to have a long and prosperous future. However, rock engineering input is an essential element to achieving success. The most accessible deposits have been mined in South Africa and although large reserves still remain, many of these are difficult to access and will require excellent rock engineering knowledge and skill in the future. This is borne out by the fact that more than 50 % of fatal accidents are related to rock engineering issues. Many of these may be addressed with rock engineering solutions which are not beyond current rock engineering technology. A reduction in fatalities and injuries contributes to a sustainable mining industry.

Jan 1, 2003

By George Watson, Gu Quanzhong, S. Gerard Sawyer

Bulkheads, also known as hydraulic seals, are used to seal abandoned workings and protect adjacent active mines from explosion and control unwanted inflows of water from poorly sealed shafts, water-bearing strata, and abandoned mine areas or gobs (1). At coal seam outcrops, bulkheads have typically been used to prevent access and to control acid mine drainage. Bulkheads have also been installed at outcrop openings located within the footprint of an embankment dam, or within the reservoir of an impoundment, to prevent stored water or slurry waste from flowing into active or inactive underground mine workings (2). Components of MICON Bulkhead Seal MICON bulkhead seals in mining applications refer to seals designed to impound liquids or slurry. The MICON bulkhead seal is comprised of two concrete block walls set in the front and back and a polyurethane/aggregate core (Figure 1). The two walls are usually dry-stacked, surface-bonded walls constructed with solid load-bearing concrete blocks (ASTM C90) or concrete building brick (ASTM C55). The surface bonding material used in the wall construction must be MSHA-approved. The type of stone, if any, used to fill the space between the walls is not essential. However, MICON generally uses No. 57 limestone in 50 lb. bags, specified to moisture control, shrink-wrapped and palletized. The polyurethane foam used in the construction of the bulkhead seal is engineering specified and formulated by density based on the optimization of cost, seal core thickness, required adhesive strength, the use of stone filler and other required physical properties.

Jan 1, 2005

The design of a mine should aim to optimise the market value by maximising revenues whilst minimising costs. In open pit mining, the nature of the extraction technique translates this objective into the maximum recovery of reserves while minimising waste extraction subject to technical, economical and safety constraints. Since the introduction by Lerchs and Grossman, in 1965, of a model that is now considered a classic in the area, open pit design has reached a level of maturity and acceptance by industry. These models are being used on a regular basis by designers and planners.This paper proposes a new alternative model for open pit design. It is based on genetic algorithms (GA) and exploits a reduction of the number of decision variables of the more traditional techniques. The novel approach provides more flexibility than traditional models; it can also be extended to consider planning problems that traditional open pit design models are not capable of handling. The algorithm has been designed for two dimensional problems and tested in a simple instance. The results obtained in this simple test are encouraging and are a good supporting argument for the development of a GA model capable of handling three-dimensional (3D) instances. The model presented in this paper is just a first step towards a full GA to solve the pit design problem and it is believed that novel tools like the one presented herein could become great allies in tackling challenging problems in open pit design, an illustration of such a challenging problem is presented and discussed.

Dec 6, 2010

By V. M. Troughton

Large diameter bored piles with grouted bases have been adopted for the foundations of the majority of the buildings at Canary Wharf in London's Docklands, including a deep basement car park. The piles are founded in the Thanet Sand which forms part of London's aquifer where water levels are reported to be slowly rising. A special pile test has been carried out to determine the effects of both the basement excavation and a possible long term rise in the groundwater level on the performance of base grouted piles. These effects were simulated by injecting water around the pile toe and thus reducing the vertical effective stress. In this paper the test layout and procedures are described and the results are presented. The test results showed that the reduction in pile base resistance under increased water pressures was less than predicted by conventional design methods based on vertical effective stress. The end bearing resistance was found to be proportional to the mean effective stress.

Jan 1, 1989

By John J. Sammarco

The U.S. Bureau of Labor Statistics reports that the mining industry has the highest average annual fatality rate (31.9 per 100,000 workers) among all major American industry. To address this, a major research program to reduce hazard exposure of miners with computer-assisted mining equipment was initiated by the U.S. Bureau of Mines.1 One application involves the manual process of extracting and hauling coal where operators, in the tight confines of a mine, can be struck or caught by mobile machinery. The approach to remedy this problem uses a guidance system on the haulage equipment so that it follows the machine that extracts coal. This, in essence, involves sensor-based docking of the machines. Sensors that can survive the hostile mine environment of dust, methane gas, and water, play the key role. Computer analysis of the mining machine's movements and empirical machine characterizations were conducted to establish operating requirements and spatial limitations to ensure proper loading of coal into the haulage equipment. These data served in the selection of a sensing system. Various technologies such as scanning laser systems and ultrasonic sensors have frequently been used in other applications but were found unacceptable. However, a near infrared (IR) sensor employing active targets met the requirements. The sensor has a nominal 75° conical field-of-view and a range from 0.1 to 18.0 m. For the single target mode, nominal range accuracy was 4.3% at a distance of 3.56 m. Correction algorithms were generated reducing the error to 0.6%. Airborne dust testing showed less than 0.8% accuracy (worst case) degradation at levels exceeding (by a factor of 7.5) concentrations permitted by Federal law. The sensor can track multiple active targets providing five degrees-of-freedom (DOF) measurements. Using four targets, the nominal range accuracy was 0.4% without correction algorithms. A guidance system for the haulage system to follow the mining machine does not exist commer¬cially. Such a system can reduce fatalities and injuries by current haulage mining equipment, and is a viable alternative to current haulage control.

By A. Normanton, B. Harris, V. Ludlow, S. Riaz

Why does a continuous casting mould powder, which works successfully on a particular caster with respect to semi quality, fail to perform on a caster of a similar design utilizing liquid steel from a similar route for an identical product without some tuning of its make-up and composition? In casting sequences of the same steel grade, why do some apparent random heats produce poor surface quality with respect to cracking when otherwise good surface quality is realized? The answer to these questions lies in the interaction of the mould powder, the casting hardware, and the casting process variables. Using, as examples, data collected from within Corus UK and during collaborative work on the assessment of mould powder performance and its effects on surface quality, the interaction of the mould powder, the casting hardware and the casting process variables is explored. The steelmaking route and its associated alumina load, unexpected changes to slag chemistry, infiltration of the slag into the mould strand gap, and the nature of the slag film are all shown to affect powder performance. Keywords: continuous casting, mould powders, alumina, slag films

Jan 1, 2004

By Adam H. Zimmerman

Introduction Noranda, like similar businesses, is suffering the pain of previously unheard of currency relationships, a cost structure built in better days, and conditions of gross oversupply possible in almost any commodity. Indeed, it does seem like the worst of all possible worlds is out there before us. To understand a Canadian natural resource company, you must know how the country is organized. So far as natural resources are concerned, Canada is not Canada. Canada is 10 provinces and each own the resources situated therein. Thus, the conditions of extraction, exploitation, and operation are all set by the province, while the conditions of trade and currency are set by the Federal government. This means that what may be the rule in Newfoundland may not be the rule in Manitoba or British Columbia. The second thing is that the Canadian currency has been a satellite of the US dollar for a long time. This means that we hold the unenviable and unjustified position of being the country with the second strongest currency in the world. What this has meant to us is what it has meant to an American operator. Since 1980, a pound of copper fetches 214% more for a Chilean than it does for us and a pound of zinc 115% more for a Belgian. From an American point of view, Canada is favored because its dollar is valued at 25% to 30% less than the U.S. However, because of industrial indiscretions in years past, Canada has a locked in labor cost disadvantage that is very hard to cope with. Canada has a unique situation with its labor unions. Many of the unions are, or have been, internationals and therefore gained undue strength in early days. Canada has a third political party of socialist persuasion. It is entirely funded by dues from laor union members. Thus, we have a politicized workforce. And finally, we have a public service that has the right to strike. This had made the public service unions by far the strongest now in Canada. What this means to the mining industry is that there is somebody out there blazing the trail. The unrelenting power of these public service unions probably creates a climate more conducive to excessive wage settlements in industry than would otherwise be the case. Study, Work, and Pray So what do we do when times get tough? In simple terms, we study a lot, we work harder, and we pray a great deal. We study a lot in terms of learning hitherto unknown strengths and weaknesses of our products, processes, and operations. We work hard in the sense that we do everything possible to improve our productivity. And we pray a lot because, so far, anything else we have done has not been enough. Some years ago, Noranda recognized that its principal base and precious metal operations were diminishing. To provide for the future, we should branch out into other resource type operations. These might be countercyclical and also perhaps a little more permanent. For this reason, Noranda entered the potash, aluminum, and forest products businesses. This, of course, was a 'brilliant' strategy that was much applauded in its early days. We built an excellent potash mine, the smallest inte-

Jan 6, 1985

By Manuel Gomez

Bituminous coals having maximum fluidity values in the 40- to 25,400-dial-divisions-per-minute (ddpm) range were carbonized in a continuous, entrained-bed reactor. Carbonization was conducted in an 8-inch diameter, vertical reactor at temperatures from 955° to 1,345° F and at air-to-coal ratios ranging from 4.63 to 16.12 scf/lb of moisture-and ash-free coal charged. Carbonization rates from about 118 to 360 lb/hr, as-carbonized basis, were examined. It was demonstrated that carbonization temperature and air-to-coal ratio must exceed minimum values for continuous operation. Within the operating conditions discussed, highly fluid bituminous coal was carbonized to produce tar and nonagglomerated char. The yield of tar ranged from 21.3 to 38.9 gallons per ton and the char yield ranged from 1,109 to 1,563 pounds per ton, all units expressed on a moisture-and ash-free basis. It was demonstrated that the maximum fluidity and the average size of the coal along with the air-to-coal ratio and the carbonization temperature act together to influence the carbonization product yields and certain properties of the products. Prediction equations were developed from the data for product yields and selected properties of the char, tar, and gas.

Jan 1, 1968

By Cary Hirner

The Metropolitan Water Reclamation District of Greater Chicago (District) is in the final phase of completing the Calumet System component of the Tunnel and Reservoir Plan (TARP) by bringing the Thornton Composite Reservoir online by 2014. The Thornton Composite Reservoir will provide nearly 30 billion liters (7.9 billion gallons) of additional storage for minimization of combined sewer overflows(CSO) and flooding in the Chicago metropolitan area. The project requires that the existing 6.7 m (22 ft) diameter Thorn Creek tunnel conveying overbank flood flows is re-routed and connected to the Thornton Composite Reservoir. This paper presents the components of the Thornton Composite Reservoir and specifically the detailed evaluation of a drill-blast tunnel. Other project features include an access shaft, control gate, energy dissipating structure, bulkheads, and live tunnel connection. The construction contract will be procured in late 2009.

The U.S. Code of Federal Regulations (Title 30) requires that a methane monitor be placed on every mining machine to continuously observe and record methane levels at the face. The monitor must provide a warning whenever methane levels are 1.0 percent or higher. An effective monitoring system will indicate a methane concentration of 1.0 percent on the mining machine before methane levels at the mining face reach 5.0 percent. Where the methane monitor is located on the mining machine is one of the most important factors that determines how effectively face methane levels can be predicted. Any change in the sampling location will result in a change in measured methane concentration. To protect the methanometer, it is usually located on the cutting boom at least 1 to 1.8 m (3 to 6 ft) outby the front cutting bits. A face ventilation system using blowing tubing was simulated in a full-scale test facility. Methane released from the face area was monitored at multiple locations on a model mining machine as well as locations near the face. Based on the relationship between concentrations measured on the machine and at the face, criteria were developed for selecting the best machine locations for monitoring methane. Recommendations are given for revising methane action levels for alternative sampling locations.