Search Documents

By Steve Signer, Ed Mchugh

Recent studies by researchers from the National Institute for Occupational Safety and Health indicate that shear loading contributes significantly to failure of bolts used for rock reinforcement in coal mine roofs, Laboratory tests on 17 bolts were conducted to study the behavior of roof bolts subjected to shear loading over a range of axial bolt loads, Fourteen strain gauges were attached to each bolt to measure axial and bending loads at seven locations along its length. The instrumented bolts were grouted through two high-strength concrete blocks, and axial tension was applied to as much as 75% of yield strength. With the block interface acting as a failure plane, shear loads were applied to the blocks at a constant rate of displacement to the ultimate strength of the bolts. The tests characterized the relationship of axial bolt loads to shear forces across a rock bedding plane and measured the distribution of axial and bending strain along the length of the bolts. 'These results will improve the selection of roof reinforcement in mine areas where high shear stresses are present, thus improving the safety of miners working in these areas.

By Joel N. Van Sant

An investigation was conducted to study possible sources of Utah refractory and structural clays that could be used for the manufacture of refractories and light or buff burning heavy-clay products. A field study was made and the clay samples tested to determine their firing characteristics. Results of the Bureau's work indicate many small noncommercial deposits of hypogenic clay occur in igneous rocks. Commercial hypogenic deposits are mostly halloysite clay developed by hydrothermal replacement of limestone. The high firing shrinkage of halloysite precludes its use as a refractory, however, halloysite produced at the Dragon Mine south of Eureka, is used for making oil catalysts. Clays and shales suitable for low heat duty refractory products are found in the Manning Canyon shale, in shales associated with coal bearing rocks, and in the Dakota formation. Some of the clays from the Dakota formation are also suitable for high-duty refractory products.

Jan 1, 1964

By W. Dziurzynski

The present article sets forward the results of field tests that made it possible to validate the mathematical model used in the VENTGRAPH ventilation engineer programmes. The case considered relates to the introduction of a new heading to the ventilation network of the mine. The utilisation of computer programmes in practice is justified by the necessity of ensuring expected performance and secure conditions in the network of mine headings, where - for example - plans are being made to utilise the transport dip-heading, taking into consideration fire and methane hazards. In the article we have presented the methodology of preparation of a database for computer programmes of the VENTGRAPH system, obtained on the basis of ventilation measurements. The next step consists in the execution of a design of the modified network and prediction, this on the basis of heading geometries, of parameters characterising the flow of air for the designed headings. Due to the fact that the heading was in the final stage of driving, following its introduction to normal operation and the stabilisation of flow values it was possible to retake ventilation measurements, which validated the results obtained through computer simulations. In order to execute measurements of the volume flow in the dip-heading, we employed a new wireless multipoint measurement system to determine the velocity field of air in the mine heading; the results are characterised by a high accuracy of measurement. As a part of fire prevention and incident management planning, a series of underground fire case studies for the a validated network flow model has been made. Results of simulations show the capabilities of the FIRE module of the mentioned software, including assessment of stability of flow directions and hints on counter and preventive measures for particular locations of fire.

Jan 1, 2009

The common approach of designing blasts on a trial and error basis is quickly coming to an end. When utilizing the full scale blast environment, trial and error can quickly become cost prohibitive and leaves much to be desired in terms of true blast diagnostics. In these situations testing is usually only continued until a perceived improvement is achieved and when the gross undesirables in blast results are removed. This does does not preclude, however, that further improvements of up to 100% or more can not be obtained.

Jan 1, 1991

By Tom Treleaven, Andrew Williams

Several contracts were let in Greenwich, Connecticut, for the installation of a sanitary sewer. The majority of the excavation was in rock and involved numerous challenges due to the following conditions:

Jan 1, 2003

By Chris Breeds, Ken Johnston, Omar Fulton

This paper describes the process typically involved with obtaining permits for quarry blasting in urban, suburban, and rural areas, including: content of SEPA (State Environmental Policy Act) driven documentation; regulatory review and comment; public interaction; public hearing(s); periodic regulatory review(s); negotiated solutions; monitoring; and the role of public interaction, demonstration(s), and education in the process. Case studies will be presented of projects undertaken in the State of Washington that illustrate the approach and regulatory interaction as well as the importance of public interaction throughout the process. Reference will be made to the role of national and state regulations and local codes and ordinances that provide additional limitations on blasting practice. The paper will also present regional blast monitoring data that are used in the permitting process and the layout and design of blast monitoring systems typically required as conditions of the quarrying permit. Our presentation will include tools, which we have developed to assist with explaining blast related phenomenon to both regulators and the public.

Jan 1, 2003

By Kyle Wagner, William Joa, Colter Angell, Catherine Johnson, Marty Langenderfer, David Doucet

The goal of any business is to seek the maximum profitability for the organization through optimization the use of resources, processes and the application of new technologies. An analysis of various case studies demonstrate that blasting can have positive impacts on the crushing and milling processes resulting in increased profitability for the mining industry (Grundstrom, Kanchibotla, Jankovich & Thornton, 2001). This paper describes the case study of two copper mines in Peru producing Cu-Mo and Cu-Au concentrates, which together with their strategic partner, have implemented a project focused on the improvement of rock fragmentation. The project was based on techniques of pattern size reduction, the use of high energy explosives and the technology of electronic initiation. Combined, these techniques were shown to have significantly impacted the efficiency of downstream processes.

Jan 1, 2019

By Donald Strickland, Peter Kresin, Dave Hall

"Have your parents or grandparents ever tried to share with you their wisdom and you ignored it because it did not relate to you‘? I have been ignorant and inevitably grew older and wished I had listened. The result: learning the hard way. As British Astronomer Fred Hoyle once said. “It is the true nature of mankind to learn from mistakes not from example.“ Hopefully we will continue to learn from the examples shared by our fellow mineral processors in these conference proceedings. It is the intent of this paper to share wisdom from the Musselwhite Mine that you may apply to your own operation.This paper is divided into three sections:1. Feasibility3. Operation3 . DesignKey points of the Feasibility and Design stages are summarized. followed by an analysis of actual operating statistics. An attempt is made to relate these statistics back to the feasibility and design with emphasis on areas of success and those with potential for improvement."

Jan 1, 1999

By R. Todd Swinderman

"Higher production demands across all bulk handling segments require increased efficiency at the lowest cost of operation, in the safest and most effective manner possible. As conveyor systems become wider, faster and longer, more energy output and more controlled throughput will be needed. Add an increasingly stringent regulatory environment and cost-conscious plant managers must closely review which new equipment and design options align with their long-term goals for the best return on investment (ROI).There are primarily two separate market segments using conveyor belts. One is in process industries such as food, chemicals, paper and powders. Handled in relatively low volumes, the bulk materials that enter these processes are generally of a consistent size and quality. The other market includes mining, coal handling and cement, where the bulk material’s quality and size vary, and the volumes are typically much greater. While both segments face similar issues with safety and environmental control, the properties of the materials handled and the volumes transferred suggest different approaches, with one thing in common: increased belt speeds requiring modern equipment upgrades.Safety at higher belt speedsWith companies recognizing that safety does indeed pay, safety is likely to become a new source of cost reduction. The percentage of mines and processing facilities with a robust safety culture are likely to increase over the next 30 years to the point where it is the norm, not the exception. In most cases, with only a marginal adjustment to the belt speed, operators quickly discover unanticipated problems in existing equipment and workplace safety. These problems are commonly indicated by the larger volume of spillage, increased dust emissions, belt misalignment and more frequent equipment wear or failures."

Jan 7, 2017

By Y. L. Su, S. Vongpaisal, H. A. Smith

"It is extremely difficult for a mine's central control room operator to control peakpower demands and to maintain normal materials handling operations at the same time. An investigation of the Falconbridge Strathcona Mine 's central control room has revealed that there are more than eight thousand possible combinations of ""situations"" that can arise. For such a circumstance, an expert system can become a very valuable tool to assist the operator in taking the most appropriate and timely action.A forward chaining expert system module has been developed for this application. The module is based on Level 5 ObjectTM software. It is graphics oriented and user-friendly. Training requirement is minimal.ForewordThis paper has arisen out of work carried out by YLS Associates and Falconbridge Limited as part of a contract between Falconbridge and the Department of Energy, Mines and Resources, Government of Canada, on the application of expert systems in mining operations.IntroductionThe electrical bill charged to large consumers by Ontario Hydro is based upon two elements: demand and energy consumption. The demand is the peak kilowatt level that the consumer has required during a monthly period. It is not uncommon for the demand portion to be as much as one third of the monthly bill. Energy consumption is the total kilowatt-hour s (kWh) consumed during the period.Ways to reduce the energy consumption part of the electrical bill involve utilizing energy-efficient equipment and operating machines in off-peak hours when a lower energy rate is charged. Maintaining the peak power below a critical level may require that simultaneous usage of major pieces of equipment be avoided. A 3000 kW skip run at an inopportune time could cost a company an extra $30,000 in that month's power cost.Potential disadvantages associated with peak power control are lost production due to work stoppage and increased operating costs due to the need to employ extra personnel. Most companies find these matters relatively easy to deal with and with incentives provided by Ontario Hydro, actively pursue this facet of energy savings (Harju , 1991)."

Jan 1, 1993

By F. Díaz-Fierros, D. Rubinos, M. T. Barral

The present work explores the reutilization of red mud, an industrial waste arising from the production of alumina, as a component of isolation technologies for hazardous substances. The work involved the study and optimisation of the geotechnical properties of red mud in conjunction with adsorption experiments of As(V) and Hg(II). The results from both types of experiments were integrated in a dispersion-diffusion model to calculate migration curves and minimum thickness of the red mud compacted layer. The geotechnical studies showed that compaction increased the stability and decreased the hydraulic conductivity of red mud barrier. Red mud sorbed high amounts of As (up to 44 mmmol kg-1) and Hg (up to 9.2 mmmol kg-1). The calculated minimum thickness of the red mud barrier was 1-10 cm for As and 2-19 cm for Hg, for an operation period of 35 years. The results obtained let to conclude that the reuse of red mud as a component of isolation systems of hazardous substances represents a viable alternative use of this residue.

Jan 1, 2011

By N. Shi, T. G. Joseph

The design of dippers for cable shovels has essentially remained unchanged for the last 100 years. In the past 10 years, shovel manufacturers have started taking another look at dipper design, resulting in changes that have borne models from major manufacturers that address some of the wear conditions and material retention problems that dominate maintenance and operational costs. However, with the exception of added lateral curvatures to the front and corners of the dipper, the geometry is essentially unchanged. This paper looks at the criteria that have resulted in the first new cutting dipper design in a century. The design is based on kinematic considerations, reflected in a revolutionary geometry that matches the range of motions of the shovel, designed to minimize wear, impact loading and power required to dig, thus maximizing productivity for a minimum energy requirement. The shape configuration is such that the weight of the dipper is reduced through wall thickness, enabling a larger capacity dipper to be conceived for the same shovel. Benefits are reflected in reduced operational and maintenance costs and increased productivity.

Jan 1, 2006

This paper examines some of the fundamental economics of mining - in particular, for optimisation studies, for production rate determination and for reserve estimates.It includes introductory discussion on the principles as to how economics drives mining investment decision-making, applicable to the optimising of pit shapes and production, or truck fleets, or any other part of the mine.The main part of this paper looks at the decision to start-up a mine and why the 'optimum' production rate to start-up a mine is not the point of lowest cost according to traditional discounted cash flow (DCF) analysis. The optimum production rate is usually substantially less than this rate. The paper recognises the difference between typical mining investments and investments in other industries that do not have the unique characteristics of mining and the problem of uncertainty resolution. It examines the marginal revenue effects, the marginal cost of capital and the value of a real option to expand pending uncertainty resolution as determinants of optimum initial production rates.The final part of this paper looks at applying these principles to renewable and non-renewable resources. It examines mine life and reserve estimates from an economic perspective.

Dec 6, 2010

By W. G. Pariseau

Introduction Caverns of 50 m in linear dimension at depths below 2300 m with a life of more than 25 years are proposed for the next generation of water-filled neutrino detectors. Little precedent exists for excavations in such an extreme environment, although some guidance is available from mining experience at great depths, for example, in South Africa, in Canada and at the former Homestake Mine in the U.S.A. Unlike mining for ore, there are choices available in the construction of such caverns that may mean the difference between success and failure. These choices should be informed by rock engineering principles. Recently proposed guidelines for orientation of brick-shaped caverns where the long dimension is a small multiple of the short dimension indicate that the most favorable orientation is with the long and short dimensions parallel to major and minor preexcavation principal stresses (Pariseau, 2005). Numerical analyses at reduced strength indicate some yielding at cavern walls should be expected but that an equilibrium state is quite possible and is aided by arching the back into a spherical dome when the cavern is an empty cylinder (Tesarik and others, 2002). The same indications of stability occur with brick-shaped caverns. However, the most dangerous situation occurs during the excavation sequence to final cavern dimensions. There are any number of excavation sequences that lead to the same final cavern shape, so there is an opportunity to partially optimize the sequence with construction guidelines that minimize peak stress concentrations during construction. This contribution discusses three practical excavation sequences that lead to the same brick-shaped cavern in the strong, massive Yates formation at the Homestake Mine where considerable rock mechanics data has accumulated through the years(e.g., Pariseau, 1985, Pariseau and others, 1995) and where actual mining on the 8000 Level indicates a strong possibility of successful investment in the next generation of large, deep neutrino detectors. The main results are: (1) a favorable brick-shape is one with dimensions in the same proportion as the preexcavation principal stresses (compressionpositive), and (2) favorable orientation of the most extreme but temporary shape of excavation is also best for the construction sequence. Analysis results from a mix of Homestake Mine data and possible excavation geometry illustrate the advantages of these guidelines.

Jan 1, 2006

By H Zhou, T Honeyands, M Zhou

In iron ore sintering, packing the granules onto the sintering strand to form a porous bed with optimum permeability is a complex dynamic process. The packed bed voidage is the key factor determining the flame front speed and the final sinter productivity and quality. Previous studies have found that granules are soft quasi-particles with a typical structure of nuclei with an adhering fines layer. The deformation of the adhering layer greatly affects the bed voidage during packing, which is related to the strength of the adhering layer and the force exerted on the granules. In this study, tablets simulating the particle size distribution in the adhering layer of granules were made for four single ore blends. Both the tensile strength and shear strength properties of these tablets were investigated as a function of water content by the uniaxial compression test and direct shear test respectively. The results of compression tests show that the adhering layer becomes weaker and more compliant with the increase of moisture. The most porous ore has a more rigid adhering layer than the other three tested iron ores at any given moisture content. In direct shear tests, the internal friction angle of the adhering layer ranged from 31° to 37° and varied little with the moisture content or ore type. The cohesion constant is around 1 kPa and is quite small compared to the stress applied to the granules during packing. Combined with the results of granulation and packing experiments, the influence of the adhering fines layer deformation on the degree of voidage loss is specifically discussed.CITATION:Zhou, M, Zhou, H and Honeyands, T, 2017. Tensile strength and shear strength properties of the adhering layer of granules in iron ore sintering, in Proceedings Iron Ore 2017, pp 117–112 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Roger A. Archabal, Omar A. Conte, Gustavo Langoni

This international case study focuses on the rigorous geotechnical interaction and results of a soil improvement program utilized to mitigate consolidation settlements of over 1.5 m [5.0 ft]. The extreme settlement results from very deep, nearly normally consolidated clay and the required high floor loading of a new Logistics Park near Bogota, Colombia. The general subsurface conditions consist of very soft clay extending to depths beyond the 50 m [164.0 ft] explored. A required 1.2 m [3.9 ft] thick fill combined with high floor loads resulted in an applied areal load of approximately 7 ton/m2 [1300 psf] (equivalent to about 4.5m [15.0 ft] of fill). Langan recommended performing a test section to validate the initial consolidation settlement calculations and evaluate possible optimization of the prefabricated vertical drain (PVD) spacing and length. The test section sizing was designed to accurately represent the stresses at depth of the future structures. Extreme settlements of over 1.5 m [5.0 ft] in the center and large differential settlements of over 0.6 m [2.0 ft] were measured between the center and corners of the test section over a relatively short test time. Discussion on the methodology, instrumentation, measured results and future optimization are presented. The recommended soil improvement varied from the standard approaches typically utilized in the area. PROJECT LOCATION AND DESCRIPTION The project site is immediately north-northwest of the city of Bogota in the Bogota Valley. The site is bordered with, and has historically been, farming land bordered to the south by the El Rosal-Bogotá highway. The overall site encompasses about 570,000 m2 [141.0 acres] of gross area and about 484,000 m2 [119.6 acres] of net buildable area. The warehouse complex will consist of 10 very large warehouses with footprints ranging from about 15,000 m2 [3.7 acres] to 30,000 m2 [7.4 acres]. The total building area is about 210,000 m2 [51.9 acres] with most of the remaining areas being paved principal drives, truck parking or administrative parking. The topography of the site is relatively flat and close to final grade in roadway areas. However, the warehouse floors will be raised about 1.2 m [3.9 ft] (equivalent to about 2 t/m2 [370 psf] considering engineered fill) to allow for truck docking. In addition, the design floor loads are heavy and estimated to be up to 5 t/m2 [930 psf] and equivalent to about 2.5m [8.2 ft] of fill. Geotechnical conditions at the site are very weak at depths of 50 meters [165 ft] or more, with soft compressible clays comprising the majority of the soil profile. The Bogota Valley is composed in some areas of very deep alluvial deposits. These deposits have been classified as an important challenge and limitation to the development of high/heavy structures such as the project in question for many years (Orozco, 2006). Soft clay deposits have been encountered even beyond depths of 100 meters [328 ft] in some regions of the Bogota Valley (Sanz, 1994). Extreme settlements can be expected if extensive and high permanent loads (above preconsolidation stress levels) are supported in these thick alluvial deposits.

Jan 1, 2018

By Gary J. Fletcher

Mining and processing activities which are proposed on private land, state leases, or unpatented mining claims are governed by numerous local, state, and federal laws which identify the procedures and conditions which must be met before resources can be developed. The respective government agencies responsible for the administration and enforcement of these laws have promulgated supporting regulations and guidelines, and have implemented certain permit and approval processes to ensure compliance. Each exploration project has a unique environ- mental setting and location which further dictates the types of air, water, hazardous waste, and wildlife laws and regulations which must be complied with before development commences. The environmental planning process should be the first step in the evaluation of existing company properties and the potential acquisition of other mineral properties. However. many company don't consider the environmental requirements for a project until the decision is made to develop the property for mining and processing. If a mining company wants to expedite the environmental planning process, it must first develop an in-house process for evaluating the project and determining the environmental approval procedures in the state where the project is located. The first stage of environmental planning involves general information which can set the overall company philosophy for development of projects.

Jan 1, 1987

By G. Wahl, H. Danilkewich, T. Mann

Developers of advanced mining projects face the challenge of how to craft a “Request for Proposal for a Feasibility Study” that will result in bids that are comparable and will lead to a successful execution of the study. Mining engineering consulting firms are challenged by “Request for Proposals” that may consist of a limited description of the Scope of Services and other items, which could present difficulties in the subsequent financing and/or development of the project. Changes in international disclosure requirements have also changed the landscape on how resources and reserves are reported by introducing new disclosure requirements and concepts such as qualified persons. This paper lays out a strategy for preparing a Feasibility Study “Request for Proposal” based on the experiences of a mining engineering consulting firm working on a diversity of projects around the world, and in light of the recent changes in international reporting standards for reserves.

Jan 1, 2002

By Paul C. Schmall

The link between artificial ground freezing and the mining industry stretches back more than 140 years, and across an ocean. Patented by the German scientist F.H. Poetsch in 1863, the technique is reported to have first been used circa 1862 in the coal mining valleys of South Wales. In the United States, the first ground freezing application, to a depth of 30 m (100 ft), occurred in 1888 for the Chapin Mine Co. in Iron Mountain, MO. In England in 1901, the Poetsch method was used for the first time to successfully sink two shafts through 24 to 27 m (80 to 90 ft) of wet sand and boulder clay at the Washington Glebe Colliery, near Sunderland. British mining engineer T.H. Cockin, in his 1905 Class-Book of Practical Coal-Mining, noted that, ?This method of sinking through thick beds of very wet quicksand has met with great success; it is one of the recognized methods of sinking on the Continent.? Mine shaft freezing soon became relatively common in Europe where the project could bear the cost of a major refrigeration plant construction. However, it was not until 1952 that the second North American ground freezing project was completed to facilitate the sinking of a 4.5-m- (15-ft-) diameter, 233-m- (765-ft-) deep shaft at a Potash Company of America (PCA) mine in Carlsbad, NM. Nowadays, ground freezing is used worldwide for both mining and civil applications. In small mine shafts of 3 to 6 m (10 to 20 ft) in diameter, excavations have been carried out to depths of more than 820 m (2,700 ft) within the protection of unbraced or unlined frozen walls. In fact, for deep mines, no better method has yet been established for sinking production shafts through deep, water-bearing ground. Major deposits of coal, potash and salt would still be inaccessible if not for artificial ground freezing. There are several advantages of ground freezing unique to the construction of shafts. Proper instrumentation can provide complete assurance of the integrity of the freeze to full depth prior to excavation. The frozen wall allows construction to be scheduled without evaluating the in-shaft time necessary to probe ahead, place additional sup-ports or deal with ground water. The freeze can be implemented perfectly through the soil/rock interface, which is often the most difficult geology in which to create a ground water cutoff by other methods. At increasing depths, any discontinuity

Jan 1, 2007

By Michael D. Justason

...a global perspective... In March of 2000, the Japanese Geotechnical Society added "Rapid Load Testing" to their national standard for pile testing. In the year 2000. it is estimated that there will be more than 500 "Rapid Load Tests" on foundations around the world. ...so what is a "Rapid Load Test", and why is it gaining acceptance and popularity?

Jan 1, 2001