Search Documents

By Steven J. Schatzel, Robert B. Krog

Frictional ignitions are defined as the ignition of a flammable mixture of methane and air that is initiated by frictional heating. Ignitions created through the addition of energy from open flames and exposed electrical circuits are not included in this analysis. Energy released in a roof fall that creates a spark and ignites a methane mixture would be considered a frictional ignition. Frictional ignitions represent the majority of all ignitions in underground coal mines. Over the study period of 1983 to 2005, a total of 1993 ignitions were reported in underground bituminous coal mines in the United States, of which 1589 were frictional ignitions. Reportable ignitions to the Mine Safety and Health Administration (MSHA) are any unintentional occurrences of flame underground regardless of duration. Frictional ignitions were reported in 155 mines and 13 states. Continuous miners represented the largest source for frictional ignitions with 1090 (68.6% of all frictional ignitions). Longwall mining operations represented the highest concentration of frictional ignitions during this study period with 1365 frictional ignitions (85.9% of all frictional ignitions). The 17 mines with the most frictional ignitions were all longwall mining operations and had 1130 frictional ignitions (307 from the shearer) that represented 71.1% of the total. In 1983, mines with frictional ignitions represented 6.9% of operating underground mines and 36.6% of total underground coal production. The percentage of operating underground mines with frictional ignitions and their total production has increased steadily and in 2005 represented 9.8% of active mines and 46.2% of underground coal production. The three coalbeds with the highest number of frictional ignitions (Blue Creek, Pittsburgh No 8, and Pocahontas No 3) had 1049 ignitions that represented 66.0% of all frictional ignitions. The three states with the highest number of frictional ignitions were Alabama (710), Virginia (247), and Pennsylvania (242) that represented 75.5% of the total. Frictional ignitions peaked in 1991 with a high of 114. In 2005, only 34 frictional ignitions were reported. If only frictional ignitions that occur at the face are considered, there have been no fatalities since 1983. Since this time, there were 33 ignitions that caused 53 workers to lose a total of 2912 working days. When including ground falls, then there have been four frictional ignitions with one incident causing two fatalities and injuring eight workers. From 1983-1991, underground productivity and the number of frictional ignitions increased. However, productivity continued to increase from 1991-2000 while total frictional ignitions fell, thereby disproving this connection between productivity and frequency of frictional ignitions. Ninety percent of all frictional ignitions occurred in underground coal mines that liberated more than 393 L/s (1.2 MMcfd million cubic feet per day) of methane through the main ventilation system. Although methane production is not the determining factor for the occurrence of frictional ignitions, it is a good indicator of the anticipated frequency.

By T. M. Barczak

Stoppings are required to resist lateral forces on the face of the structure to control pressure differentials created by ventilating air. The design criteria in other parts of the world, including Australia, exceed this requirement by specifying over pressurization control to as much as 14 kPa (2 psi) in the active sections and 35 kPa (5 psi) in the main ventilating control areas. This is done to provide protection to the mine workers from explosive or air blast events within the mine that can create this over pressurization. The National Institute for Occupational Safety and Health (NIOSH) has been conducting research to develop a new testing protocol for rating mine ventilation stoppings. The premise of this work is that arch-loading conditions more accurately reflects the transverse load capabilities of stoppings in underground coal mines than the freestanding flexural strength test specified in the current Code of Federal Regulations (CFR). This work clearly shows that the transverse load capabilities of dry-stacked, mine ventilation stoppings are dependent upon the material strength of the block and the height and thickness of the wall, none of which are part of the current CFR criteria based on ASTM E-72 specifications. This paper compares the transverse load capabilities of several block materials and wall dimensions commonly used in stopping constructions based upon simulated three-hinge, rigid-arch loading tests of half-wall constructions in the NIOSH Mine Roof Simulator. The results indicate a wide-range of transverse load capacities, ranging from as low as 21 kPa (0.3 psi) to as much as 117 kPa (17 psi) for the conditions evaluated in this study. The current CFR criteria do not distinguish between applications of these stopping designs despite their wide variance in transverse load capabilities, which is not conducive to employing ventilation control strategies that isolate certain sections of the mine to prevent injury to mine workers.

Jan 1, 2009

By Leon H. Bruner

This paper presents a case study describing how a global consumer products company with 138,000 employees that markets over 300 brands in 180 countries is building sustainability into the rhythm of its business. This strategy extends beyond social investment programs by incorporating sustainability into the fabric of product design, manufacturing operations, employee engagement and stakeholder partnerships. During the implementation of this program it has been necessary to be explicit about sustainability and its importance to the business, to broadly define sustainability, to ensure that sustainability is not added work, to eliminate trade-offs between performance, value and sustainability and to implement programs to ensure that sustainability is incorporated into the DNA of the company. Our program continually emphasizes the importance of making no tradeoffs between consumer acceptance of sustainable products and sustainability investments. We also work diligently to overcome the challenges of engaging employees around the world to implement a single coherent sustainability strategy that delivers great results.

Jan 1, 2010

By Mikhail P. Nesterov

The paper presents the results of the research that can forecast the development of subsidences and deformations of the earth surface with time in the permanent marginal areas of the movement troughs arising when mining sylvinite beds in the Upper Kama deposit of potash ores where the rock formation support is made by means of interchamber (rib) pillars of various yieldability.

Jan 1, 1997

By Wouter Hartman

Xuandong Coal Mine is mining coal in one of the most challenging underground environments in the world. This work has found that it is not only challenging but it also has the composition for some interesting rock mechanics and ground control conditions. The paper highlights the extreme mining and rock mass behavior conditions encountered when mining coal at 900 m below surface. It was found that the ground control environment associated with geological weakness, low coal material strength and stiffness, was reasonably well controlled; however, the chain pillar geometry and design did not take these geological weaknesses into consideration. Some of the chain pillars employed were quite large, which resulted in floor punching and secondary floor heave, which causes extreme difficulty for production. No barrier pillar has been employed except for the center 164-m-wide main headings pillar with a w/h ratio in excess of 40. After assessing the location and geometry of a 200-m-thick dolerite sill overlaying the coal measures, we found the probability of it breaking up into to smaller fragments and producing a larger goaf to be low. Therefore, the influence of the dolerite sill on chain pillar loading is considered small compared to the low coal, immediate floor and roof rockmass strength. It is further recognized that horizontal stresses could be locked up within the dolerite sill, which would likely result in regional bending that would be distributed through the chain pillars. This has, to some extent, already occurred, and the effects have been seen and felt through excessive floor heave, pillar punching, and coal bumps (seismicity). We?ve also found that there was a need to employ basic rock mechanics principals in assessing the stability of future multiple seam mining layouts.

Jan 1, 2012

By S. Uddin

An integrated device has been developed to measure sedimentation potential, conductivity and pH simultaneously of particulate systems. Maxwell?s model was used to calculate volume fraction of solid from the conductivity data. In this approach, all system variables are known and zeta potential can be calculated from Smoluchowski?s equation. The technique is validated by comparing zeta potential vs. pH for alumina and silica suspensions with electrophoresis measurements. The technique was extended to mixed alumina/silica systems. Sufficient column height along with size difference between the two minerals allowed gravity fractionation during settling. Sedimentation potential measured over time identified the transition from one mineral to the next. Using XRD analysis the results supported the correlation between surface charge and sample composition. This is a step towards characterizing surface charge of mixed systems of interest in mineral processing.

Jan 1, 2010

By A. T. Iannacchione

Underground stone mining represents an emerging sector for the U.S. mining industry. As this expansion takes mines under deeper cover and as more efficient mining methods are utilized, adequate stone pillar design methods will become more important. It is the purpose of this paper to examine current design practices and to discuss issues for safe mine layouts so that a rational first approach towards balancing the demands for increased production can be weighed against increased risk to worker safety from rib instabilities and pillar failures. Seventy-two stone mine pillar designs were examined. Pillars with width-to- height ratios below 1.5 and subjected to excessive stress levels appear more likely to fail. When width-to- height ratios fall below 1 .0, defects in the pillars, such as through-going discontinuities, can have a significant influence on stability. Discontinuity persistence, dip, material properties, and orientation are important factors controlling pillar strength. The influence of discontinuity dip, a characteristic easily identified in the field, was examined so that its presence could be accounted for in developing generalized guidelines for pillar design.

Jan 1, 1999

Removal of Dilute Toxic Anions in Wastewater Using Aluminum Hydroxides Co-Precipitation Method

Sep 13, 2010

A study of literature on the epidiorite dykes which transgress the Broken Hill lode and its wall rocks reveals a considerable diversity of thought regarding the time of emplacement of such dykes. In this paper it is deduced that the epidiorite dykes were formed at a late stage and were probably post-ore. Detailed mapping, sampling, and correlation of data from over 100 exposures substantiates this deduction. Physical disruption of the epidiorite dykes is indicated and some interaction of the epidiorite and ore at the time of intrusion is inferred.Further petrological study may confirm this.

Jan 1, 1968

By C. W. Davie

"This paper is the second of a series of progress reports4 on a study of the hydrometallurgy of manganese which is being conducted in an endeavor to make possible utilization of the large deposits of low-grade domestic manganese ores that occur in several States.There are at least four processes in which a knowledge of the action of SO2 gas on manganese oxides at elevated temperatures may prove of value.One of these involves dissolution of manganese from ores. The Bureau of Mines has investigated the hydrometallurgy of manganese by a process in which SO2 gas, a waste product at many smelters, is passed into water to form a solvent for manganese. Although several manganese minerals were readily dissolved, rhodochrosite (MnCO3) was attacked but superficially.5 Recent experiments have shown that a roast at 650 to 9000 C. converts the manganese of rhodochrosite to a form that is quickly dissolved by a weak SO2 solution.6 Introduction of smelter gases containing much as 5 per cent SO2 during such a roast would not add much to the cost of the operation, and might result in the formation of considerable water-soluble manganese sulpate.Another case involves a subsequent step in the hydrometallurgical process, namely, the formation of oxides of manganese with simultaneous evolution of SO2 by the heating of the MnSO4 produced by evaporating its solution.A third has to do with the roasting of zinc sulphide ores containing manganese as a preliminary to leaching. During purification of the solutions to be used for the electrolytic deposition of zinc the iron must be oxidized to make possible its removal. Manganese dioxide has been used for this purpose,7 and since manganese compounds are present in some zinc concentrates,8 it is of interest to learn what happens to the manganese in a zinc sulphide or on roasting, and what portion of the manganese in the roasted product might be available for oxidation."

Oct 1, 1930

The methods and equipment developed and used at the Mount Isa mine to obtain samples of uncemented hydraulic fill lying above major horizontal pillars are described. From existing underground development, samples were obtained at distances up to 50 m, of which up to 30 m was through hard rock. Samples were used to predict fill behaviour as it affected mining security during recovery of the pillars.Specialized equipment for difficult sampling situations and also other sampling exercises are described.

Jan 1, 1976

By Sean Harvey

One of the manifestations of the dynamically induced failures in deep coal mines is the violent ejection of coal from the ribs. A possible protection against such failures is the use of a specifically designed dynamic support system with reinforcement units having the sufficient capacity to absorb the kinetic energy of the dynamic failure and a skin support that can adequately contain the disintegrated coal. With this method of mitigation in mind, a recently introduced yielding rock bolt, trade name Roofex, has been identified (Harvey and Ozbay, 2009) as a possible energy absorbing component of a dynamic support system. According to the manufacturer?s specification, the Roofex bolts can yield 300 mm (or more) displacement while holding 80 kN pull load. In order to assess the performance of this support unit in coal ribs, a series of in situ pull tests performed in two coal mines in Colorado. The results show that, under conventional pull test loading conditions, Roofex yielding bolts perform very close to their claimed specifications, thus showing a potential for their use as the main energy absorbing component of a dynamic support system. Further studies are required to confirm the in situ performance of these bolts under dynamic loading conditions and also to develop a containment component for a dynamic support system for the mitigation of dynamic coal rib failures.

Jan 1, 2009

By Douglas Anderson

Even though there is always a feeling of anticipation before a blast is detonated, most blasts are part of a day’s work. Once in a while there is an event that impresses even the most jaded blaster. Few blasts have had the impact of the Kingdome implosion in March of this year. Fortunately for both the Seattle area and the explosives community, the “impact” of the implosion was far less than many local residents had feared. This outcome, of course, was not by chance, but the result of careful planning and design. An urban implosion requires a mix of engineering, logistics, and public relations. Unique challenges on this project tested the resourcefulness of the entire team.

Jan 1, 2001

By James L. Austing, Allen J. Tulis, Ronald Pape, Ronald G. Draftz

In a certain sense, the explosives industry began in the 13th century with the invention of black powder, which is an intimate mixture of sulfur, carbon black or charcoal, and potassium or sodium nitrate. For several centuries thereafter, black powder was the sole general purpose energetic material, serving as an igniter, propelling charge, bursting charge, and blasting agent. By today’s standards, black powder is totally inadequate for the latter three functions, but its use continues as an igniter for propellant charges because of its unique ability to ignite and burn under ambient conditions. The history of the development of black powder was reviewed by Rose (1980).

Jan 1, 1995

By Staff

This U.S. Bureau of Mines publication presents the results of investigations into the fire and explosion hazards of oil shale rocks and dust. Three areas have been examined: the explosibility and ignitability of oil shale dust clouds, the fire hazards of oil shale dust layers on hot surfaces, and the ignitability and extinguishment of oil shale rubble piles.

Jan 1, 1989

By L Barrere, J P. Sykes, A Trench, R S. Davies

Western Australia (WA), alongside Brazil, has remained at the forefront of the global seaborne traded iron ore market for over 40 years. Despite this apparent stability and strong market position, WA continues to face strong external international supply-side competition, mainly from Brazil, but also periodically from often marginal, non-traditional sources of iron ore. Additionally, WA iron ore supply has undergone significant decadal change internally, both of an evolutionary (brownfields expansion) and revolutionary nature (major new greenfields projects). Since 2006, a new generation of WA-focused iron ore explorers, developers and producers have emerged.The majors, BHP Billiton and Rio Tinto, have expanded mine production to record levels and the Roy Hill project is now approaching nameplate capacity. Fortescue Metals Group (FMG) is, however, the largest new market entrant of the last decade, delivering upon their vision of becoming the ‘new force in iron ore’. Unlike most of the other new WA market entrants, FMG’s operations are substantive. Most of the other smaller, new WA iron ore miners have struggled during the period of falling prices, though it is worth noting that collectively they have made a material supply-side impact during the price boom – typical of marginal supply. Finally there have been some contributions from new magnetite projects, however, the delivery and economics of these projects have not met expectations.In this paper, we touch briefly upon the key global market changes of the last decade, namely China-driven demand growth and the changes to the pricing mechanisms for iron ores – before reviewing the rise in WA iron ore supply in response to these markets. We finish by focusing on the most significant WA-focused supply-side development of the last decade, the rise of FMG as a major new supplier and the strategic situation that facilitated its rise. The unprecedented China-led rise in iron ore prices felled many traditional barriers to market entry into an oligopolistic industry, allowing many new market entrants (in WA and around the world). However, the downturn in iron ore prices resurrected these barriers to entry, with only FMG (thus far) breaking the entry barrier with significant scale. Difficult corporate decisions have been forced upon the smaller WA iron ore miners who, in some cases, will now struggle to further expand, or indeed continue to operate in the longer run.The changes that have taken place over the last decade of WA iron ore production hold insights for other emergent mineral commodity exports from the state. Successful market entry, even when industry barriers are high, does not always require an immediate low-cost production assumption alongside a strong balance sheet. FMG could see a new market, within an established commodity market, target an appropriate and new product at it, overcome temporarily-felled barriers to entry in infrastructure and finance, then innovate and aggressively cut costs ensuring it was behind the barriers to entry when they rose again after the price boom.CITATION:Barrere, L, Trench, A, Sykes, J P and Davies, R S, 2017. New generation Western Australian iron ore – strategic insights far beyond the Pilbara?, in Proceedings Iron Ore 2017, pp 375–386 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Jay L. Hodkinson

Replacement of an aging twin span river crossing in Vermont required a temporary bridge to accommodate traffic during construction. Soils beneath the temporary approach embankment consisted of very soft organic clayey silt underlain by interbedded, loose alluvial fine sand and silt/clayey silt. Reinforcement was required for the southern temporary approach embankment to limit settlement and to increase global stability factors of safety. A ground improvement design was developed using Rammed Aggregate Pier® reinforcement and was included in the contract documents as an FHWA Category II Experimental Feature. Instrumentation intended to document the performance of the supported embankment was installed. Piers were then constructed and monitoring commenced as embankment and bridge construction occurred. Weekly instrumentation data reports indicated continuing excess pore water pressure, settlement, and lateral deformation of the subgrade soils as the embankment and temporary bridge abutment was constructed. In response to the unanticipated monitoring results, further investigation indicated that significant deviations from the conditions and basis upon which the ground support design was developed were made during construction. This paper discusses these deviations and their specific impacts to embankment support performance, how these deviations occurred, the role that the ground support system played in maintaining global stability, measures taken to limit further detrimental impacts to the embankment, and provides recommendations for contract document preparation and construction oversight to prevent similar situations from occurring on future projects.

Jan 1, 2011

By D A. Vogel

"Sampling may be mandatory for safety or environmental reasons. It may be because the value of a sale needs to be determined or to provide important data for investments. Whatever the reason, an incorrect sample will come at a risk. Only the person that relies on sampling data can imagine what the potential cost of such risk is.Sampling itself has a cost too; the direct cost of a quality control department and indirect cost for interrupting a process, such as stopping a conveyor belt during loading. If all material is the same then only one small sample is enough. But if all the material is different, then a very large sample must be tested; in the conveyor belt scenario it must be stopped very frequently and the associated cost will be high.A good sampling plan finds the proper balance between risk and cost. A good sample must be small enough to handle yet large enough to be representative for what information is required. All good samples have three things in common: there was proper access to the material the sampling tool allowed equal probability of particles being selected nothing was disregarded, everything was included.This too is the core of Gy’s ideal sampling scenario, where all particles have the same probability of being selected and included in the sample. There is risk of bias when part of a lot is excluded from the sample. Extra care is needed when sampling particularly heterogeneous, segregated or layered materials. The sampling tool should never systematically leave out a portion; it shall not push aside large or hard particles. Wet samples shall not stick to the sampling tool. This extends to sample preparation too when reducing particle size and dividing the sample in the process.CITATION:Vogel, D A, 2017. Access, select, include – a review of the commercial sampling of traded bulk commodities in the context of Gy’s Theory of Sampling, in Proceedings Eighth World Conference on Sampling and Blending, pp 367–378 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 9, 2017

By G. Bee, Z. Gavelan, R. Espinel, Y. Roditis, X. Ochoa

In August 1996 Barrick Gold Corporation acquired the Pierina property, an advanced stage exploration project, high in the Andean Cordillera of Peru and in November 1998, in a record time of just over two years, poured the first gold. After more than three years of a very successful operation at some of the lowest operating costs in the world, this presentation serves to briefly describe the project through design, construction and start-up and in particular to spotlight some of the challenges that have been overcome in valley heap leaching in a high rainfall, alpine setting.

Jan 1, 2002

By John Heilig, Patrick Andrieux

"Near-field monitoring of blast induced seismic vibrations is a practical and useful way of assessing blast field behaviour for diagnosis and optimization purposes. It is also necessary in order to provide the information from which empirical vibration prediction equations, such as the one proposed by Holmberg (11 for example, can be derived. (Strictly speaking, the “near field” extends from the blasthole itself to about one charge length away from it; however, throughout this article, “near field”will.most often refer to the outer limit of this zone, from roughly 0.75 to 1.50 charge length away.) In order to obtain reliable data, proper field monitoring techniques are of paramount importance. Once the data are properly recorded, analysis can be done either in the time domain (describing vibration amplitude vs. time) or in the frequency domain (usually describing vibration amplitude vs. frequency)."

Jan 1, 1995