Search Documents

Some of the problems associated with drill core evaluation of alluvial tin deposits and correlation with plant-scale recovery are discussed. Panning churn-drill cores on site tends to undervalue such deposits because of failure to recover completely all the available liberated cassiterite, and secondary gravity processing may also fail to give an accurate determination of potentially recoverable tin. However, by using a combination of heavy liquid separations, x-ray fluorescence analysis for Sn, and normal methods of reflected and transmitted polarized light microscopy, a quantitative assessment of alluvial material can be carried- out. The information obtained may include the liberation characteristics and distribution with size of the cassiterite, the nature and quantities of the various gangue minerals, and the amount of potentially recoverable cassiterite in the material as compared with the amount locked with light gangue minerals and hence difficult or impossible to recover. In addition, an analysis of the efficiencies of the various gravity processes, such as panning, jigging, and tabling, used to determine "recoverable tin" in the alluvial material, can be carried out. A detailed example is given of this type of investigation, in which an assessment was made of a churn-drill core from Uncia, Bolivia.

Jan 1, 1970

By Claude Bazin

"Laboratory semi-batch flotation tests were conducted using two different sulphide ore samples. The size reduction was adjusted to cover a wide range of flotation feed size distributions. Results show that similar recoveries can be achieved independently of the fineness of grind. This result suggests that possible energy savings could be achieved by a redistribution of the power between the grinding and regrinding mills. The behaviour of the selectivity curves shows that some gangue minerals are more sensitive to particle size than other ones, implying the existence of preferential associations between minerals in the ore.INTRODUCTIONInteractions between grinding and flotation have been studied for many years, and still a robust model to link the two processes lacks to be developed (Girard et al., 2005; Bazin et al., 2001). The ore size reduction liberates mineral grains, while flotation separates them into valuable minerals and gangue. The more size reduction that is applied to the ore the more important is the mineral liberation but also the production of fine particles that can pose problems during flotation (Trahar and Warren, 1976). The definition of the grinding requirement for flotation is a complex problem (Rickelton and Dell, 1977; Sosa Blanca et al., 2000; Morrison, 1993; Wei and Gay, 1999).This paper analyzes the effect of the fineness of grind using semi-batch flotation test results. The first two sections describe the test procedure and the results. The third section analyzes the results in terms of liberation and selectivity, and proposes a possible redistribution of power between grinding and regrinding mills."

Jan 1, 2006

By Uwe Wilhelm

Pittini Group has contracted Danieli in 2011 for the supply and replacement of the existing EAF at Ferriere Nord Plant in Osoppo. This was a very challenging project: giving the fact that the Meltshop was operating already under very high performance level, there were many elements involved for the project to improve (reduce the amount of charges, promote highest possible chemical energy utilization, allow best optimization on existing transformer power, modification on Drop Out box and Water Cooled Duct, Hydraulic System for EAF, Scrap Bucket design to fit to new EAF with existing loading and transport system, Automation System Review and Upgrade) as well as limitations of the existing installation (limited space, lifting capacity building and cranes and the required solutions for fast shell and roof exchange). All furnace parts, as well as installation engineering, were developed and discussed carefully with the Customer to either provide proven and reliable concepts, but also to define solutions for fast installation/maintenance access and quick exchange for offline turnaround. In the end, from disassembly of existing equipment up to the first heat of the new furnace, only 38 days were necessary. First heat was made on January 24th 2013, on the 6th production day 32 heats where produced at nominal design capacity and 28 days after start up 100,000 t liquid steel have already been produced.

Jul 30, 2018

By Carl Lubbe, Ron Frye

Numerous articles have been written regarding the effects of blast control plugs in an attempt to quantify stemming ejection rates, air overpressures, fragmentation’and other parameters measured using these devices. In an effort to further attempt to understand the function of these devices, field and laboratory research conducted with various stemming devices was performed to enhance existing data sets and analyze otherphenomena that occur when these products are used.

Jan 1, 1998

By J. -W. Kim, Y. -B. Kang, H. -G. Lee

The effect of SiO2addition on the decomposition of Li2CO3was investigated at temperatures up to 1000ºC. It was found that addition of SiO2greatly enhanced the decomposition of Li2CO3. The main decomposition reaction started at around 600ºC, and completed just above the melting point of Li2CO3. The major decomposition product was Li2O?SiO2irrespective of the Li2CO3to SiO2mixing ratio while both reactants were available. It was ascertained that a liquid layer betweenLi2CO3and SiO2particles formed and facilitated the decomposition reaction. The governing reaction of the decomposition was the one between the dissolved Li2CO3and SiO2in the liquid layer to form Li2O?SiO2. The decomposition rate was independent of the Li2CO3/SiO2mixingratio until either one had been completely exhausted. When excess Li2CO3existed, it further reacted with the initial product of Li2O?SiO2to form 2Li2O?SiO2. When SiO2was found in excess, on the other hand, no further reaction took place. This is attributed to the fact that uponLi2CO3exhaustion there is no liquid phase available to facilitate further reaction. The apparent activation energy of the decomposition of Li2CO3in existence with SiO2is 198 kJ mol-1.

Jan 1, 2004

By Ram Avtar

High tensile thick plates (>80mm, weight ~3000 Kg) of medium carbon low alloy steel, when heat treated, manifested higher percentage of crystalline area (>20%) in fractured surface. Such problem was not encountered in thinner plates. The genesis of higher crystallinity in fracture was examined. It was observed that the thicker plate undergone slower rate (Average 0.9oC/Sec.) from soaking temperature to Ms temperature) of cooling after austenising during oil quenching and thereby quenched microstructure had upper bainites. During tempering of as quenched bainite, additional precipitation took place at the lath boundaries of bainite. This led to weakening of grain boundaries and aided easy crack propagation during fracture and resulted in formation of higher percentage of crystalline area in fractured surface. Enhancement in cooling rate (Average 1.8oC/Sec. from soaking temperature to Ms temperature) of austenised plate by switching over from oil quenching to water quenching practice resulted in complete transformation of austenite into martensite and produced ductile fracture (zero Crystallinity). Plates conformed improvement in mechanical properties between 2-5%.

Jan 1, 2009

Study on Pure Mineral Flotation Tests of Low-Grade Phosphate Ore in Zhijin, Guizhou Province, China

Sep 13, 2010

This report is the 22d in a series summarizing Bureau of Mines research and technologic work on coal and related investigations.2 3/ A summary of work published during 1957 and of work in progress is presented. Details regarding the subjects treated in the publications may be found by referring to articles cited in the footnotes. The objective of the coal work of the Bureau of Mines is to obtain information that will lead to improved production and utilization of coal, thus conserving a most important national asset.4 5/ Though studies of mining methods and exploration of various coalfields ma; contribute directly to improved production, no less so does the work in health and safety. The many problems relating to chemical and physical properties of coal reflect the need for an understanding of these properties for the most effective use of coal in its various fields of application and for the development of new methods of processing coal. Studies of existing and proposed processes of combustion, carbonization, gasification and hydrogenation of coal are necessary for increased efficiency in its use. Engineering service provided by the Bureau is of direct value in the conservation program in preventing waste. Stations where the main coal activities of the Bureau are carried out are shown in the following list:

Jan 1, 1959

By M. du Toit

Cromanite?is a new high-strength austenitic stainless steel developed by Columbus Stainless. It contains approximately 19 percent chromium, 10 per cent manganese and 0,5 per cent nitrogen. Cromanite can be welded successfully, but due to the high nitrogen content of the base metal, certain precautions have to be taken to ensure sound welds with the desired combination of properties. Although no matching filler metals are currently available, Cromanite can be welded using a range of commercially available stainless steel welding consumables. Welds produced using E309L, E307, E307Si and E312 filler wires are resistant to hot cracking and the formation of nitrogen-induced porosity, but the hardness, strength, ductility and toughness of the welds are generally inferior to those of the base metal. In applications where full use is made of Cromanite?s high strength, welds with matching strength levels would be required. In wear applications, where Cromanite is used primarily for its work-hardening properties and corrosion resistance, lower strength welds would probably be acceptable. Welds produced using E307 filler metal demonstrate the best combination of properties for use in wear applications. The welds display high rates of work-hardening that would result in increases in hardness and strength when subjected to abrasive or high impact environments.

Jan 1, 1999

Greater use should be made of lineations in investigations of the engineering properties of rock masses and in structural studies guiding prospecting programmes.A prominent alignment of elongate mineral grains and stretched pebbles usually marks the primary direction in which metamorphic rocks have been extended by flow. In local adjustment zones separating masses that have extended different amounts, this lineation has been a direction of slip. Kinks and crumples resulting from this slip lie in secondary lineation directions transverse to the primary mineral lineation.During deformation relatively mobile materials move into dilatant zones caused by irregularities in primary flow directions. This secondary movement transverse to lineated, primary-flow directions is the cause of crenulations and folds with axes parallel to flow lineations.INTRODUCTIONThe arrangement of inequidimensional particles in rocks is rarely statistically random. Platy minerals tend to be parallel to bedding and foliation planes. Elongate particles and linear structures lie most frequently in certain lineation directions. The types of elongate particles in lineated rocks include needle and blade shaped mineral grains, sheared out segregations, and stretched pebbles, amygdules, and aolites.Crenulations and kinks are the most common of the linear structures involved.Faint lineations are readily overlooked. Even strong lineations have been ignored. This is unfortunate as even weak lineations may be important.Use of lineation information Well-developed lineations influence the mechanical properties of rocks. Quarry workers have long known that the mechanical properties of rock masses vary directionally...

Jan 1, 1965

By L. C. IlsLey, M. W. Von Bernewitz

"Introduction.Several hundred thousand open lights are daily carried in coal mines of the United States, each lamp being a menace to life and property through fire or explosion. They have been responsible for many disasters in the past, and will be again. Flame safety lamps have been available for over a hundred years, but during the last ten years safe and practical electric lamps have been perfected. These have eliminated many of the flame safety lamps, and in a few mines have replaced open flame lamps. But there are still more than twice as many open lamps as electric lamps in our mines, and the open lamps should be discarded in favor of an approved type of electric lamp. There are several electric miners' lamps which have been approved by the Bureau of Mines for safety and efficiency, give good light, and are easily maintained and carried, some flame safety lamps will always be used, hut mostly for detecting gas; although they might be supplanted if some simple, reliable, and cheap gas detector were developed.Explosion Hazards from Open Lights.An open light and gas*** constitute a vicious hazard; while if there be coal dust present in the vicinity the consequences are multiplied many times. An open light and black blasting powder also constitute an explosion hazard, vividly attested by several serious disasters."

Jan 1, 1924

By R. Poisel, C. Scavia, Preh A., W. Roth, M. Pirulli

ABSTRACT: Two methodologies for the three-dimensional simulation of the run out of rock avalanches are presented: one based on a granular approach and the other based on a continuum equivalent approach. An evaluation of the possible run out area of the Oselitzenbach landslide (Carnic Alps, Austria) has been carried out applying the two methodologies. The combined use of these two approaches makes it possible a comprehensive assessment of the run out area. RESUME: Deux méthodologies pour la simulation tridimensionnelle de la propagation des avalanches rocheuses sont présentées: la première est basée sur un modèle de type granulaire et la deuxième sur un modèle du continu équivalent. Une évaluation de la propagation éventuelle de l’avalanche de Oselitzenbach (Alpes Carniche, Autriche) a été réalisée en utilisant les deux méthodologies. Les résultats obtenus montrent que la combinaison des deux approches rend possible une analyse plus complète de la phase de propagation. KURZFASSUNG: Für die dreidimensionale Modellierung eines Felsmassensturzes (sturzstrom) werden zwei Methoden, eine granulare und eine kontinuumsmechanische Methode, vorgestellt. Beide Methoden wurden zur Abschätzung der Ausbreitung (runout) der Massenbewegung Oselitzenbach (Karnische Alpen, Österreich) herangezogen. Die kombinierte Anwendung beider Methoden ermöglichte eine umfassende Beurteilung des möglichen Ausbreitungsbereichs.

Jan 1, 2003

By Larkin F, Farrer E, McGhie R. R

The Electrolytic Zinc Company of Australasia Limited commenced productive operations during February, 1936, at the- Rosebery and Hercules mines, which are situated near Rosebery, Tasmania. At this time it was decided that before re-organizing the steel sharpening shop a test should be made of the relative merits of conventional drill-steel and detachable bits. For this purpose Ingersoll-Rand type"I" thread centre hole.jackbits were selected and seventy-two of these were tested against conventional steel. Results indicated that, under the conditions pertaining at these mines, j ackbits should prove more economical than conventional drill-steel bits, and that a large-scale test, under working conditions, should be made. This was done by gradually replacing conventional drill-steel with jackbits at the Rosebery mine. Results were satisfactory and by the end of 1936 both mines were using only the jackbits.

Jan 1, 1939

By Brian P. Stapleton, Bill M. Stewart, Joel R. Warneke, Curtis C. Clark

Of the 28 accident/injury classifications listed by the Mine Safety and Health Administration, handling materials is second only to roof falls in terms of generating the highest number of reportable accidents in active underground coal mines. Two materials-handling activities that cause numerous injuries each year are the categories of “handling supplies or material, load and unload” and “moving power cables.” Mechanization and mine worker activity training are two methods that can aid in preventing these injuries. This paper describes three mechanical methods—the mobile manipulator, the in-mine hoist, and a cable-handling system—being developed and tested at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. Two of the devices are specifically designed for loading, unloading, and moving supplies and materials, and the third device is for handling trailing cables in the confined spaces of coal mines. Also described are safety solutions developed for underground coal mines geared to showing miners safe and unsafe ways of performing various materials-handling tasks.

By Lancucki C. J, Nickson N. M

X-ray diffraction and differential thermal methods were used to determine the mineralogy of some clays used by the heavy clay industry in the Adelaide area. A detailed analysis was made of the mineralogy and particle size distribution of eighteen samples from beds in two pits in the Recent sediments in the Adelaide plains, of six white clays developed from the weathering of the Adelaide series of sediments, and of four Recent alluvial clays from a pit in the Mount Lofty ranges south of Adelaide. Structural clay products in the Adelaide area are manufactured from mixtures of these clays, so the mineralogy and particle size distribution was determined of eighteen clay mixtures used to make red bricks, cream bricks, facing bricks, pipes and tiles.Knowledge of this mineralogy is important in understanding the ceramic behaviour of the clays.INTRODUCTIONIn this investigation an account is given of the clay mineralogy and particle size distribution of some ceramic clays from the Adelaide area. The clays are used in the manufacture of structura,l clay products and the results to 'be described are part of an overall 'plan of study covering the heavy industrial clays and shales of Australia. Previous work has been published (Cole and Carthew, 1953; Ferguson, 1954; Ferguson and Hosking, 1955; Cole and Nielsen, 1958/59).In this work no attempt has been made to examine clays from all pits engaged in supplying materials for the structural clay industry. However, in 1954 the senior author collected detailed samples from two pits working in Recent alluvial clays in the Allenby·Gardens and Beverley areas near...

Jan 1, 1963

By R. T. Jones

DC arc furnaces are widely used for steel scrap melting as well as for reductive smelting of ore fines. Industrial smelting applications include the smelting of chromite to produce ferrochromium, the smelting of ilmenite to produce titania slag and pig iron, and the recovery of cobalt from nonferrous smelter slags. A number of myths and misconceptions are widely held, especially regarding: the age of the technology, the use of a hollow electrode, arc stability and shape, arc and bath radiation, interaction between the arc and molten slag, electrical behaviour of arcs and slags, a comparison between AC and DC furnaces, DC reactors, the lifespan of bottom electrodes, and the applicability of DC arc furnaces to various metallurgical systems.

Jan 1, 2011

By Pablo Velasco

The Belize economy recorded modest growth during 1980; the growth of the gross domestic product (GDP) in real terms was between 1% and 2%. At current prices, the 1980 GDP reached $108 million2. This output was largely attributed to the performance of a few industries, mostly nonminerals. Such performance improved significantly the balance of payments situation by reducing the deficit from $19 million in 1979 to $4 million in 1980. The rate of inflation was an estimated 18% in 1980 and would have been greater if not for a conservative monetary policy and price control on a number of essential items. Expert earnings increased $43 million, or 50%, from the 1979 level. After increasing more than 25% in 1979, imports increased only 6% in 1980 to a level of $141 million owing to the decline in investment and stabilization of petroleum prices. The balance of trade deficit was $9.8 million in 1980, a marked improvement from the 1979 level of $45.1 million. The mineral output for Belize accounted for only a fraction of 1% of the GDP. Such activity was limited to the production of limestone, marl, and sand and gravel, all of which were primarily used in construction of the Northern Highway between Orangewalk and Belize City. Mineral resources are deficient or nonexistent in Belize for the majority of metals and nonmetals, although the Government and others continue to believe that petroleum must exist in Belize. The proximity to Mexican oilfields and the growing finds in the Peters area of Guatemala support this expectation. The Government continues encouraging exploration onshore and offshore and offers terms that

Jan 1, 1982

By Stephen Chung, Graham Mustoe, Joe Haid

In an open cast coal mining operation, a 305 m (1000 ft) long by 49 m (160 ft) thick overburden cast blast can produce more than a million cubic yards of broken muck that needs to be removed before the coal recovery process can start. In the Powder River Basin of Wyoming, it is common to see 30 to 40 percent of the overburden cast to a spoil that does not require rehandling with heavy equipment. Therefore, the higher the percent cast, the better the cast blast is rated. However, depending on the shape of the muck profile, there is often 20 to 30 percent of the muck standing in front of the high-wall. This portion of muck would require a number of dozers to push down to the dragline pad level. From the mine operator point of view, it is believed that for a given muck profile, there should be an efficient dozer pushing method such that a dragline pad can be developed in the shortest time. As a tool for analyzing this dynamic problem, a 2-D discrete element model, i-PushTM, has been developed to simulate a dozer pushing operation. This mechanistic model takes into account the dozer blade geometry, the dozer operating procedure (e.g. cut-depth, blade fill distance, forward and reverse speeds at specific slope angles), material density and cohesion. To demonstrate how i-PushTM can be used to help determine the most productive push routine, this paper presents three dozer push methods to compare the effectiveness of pushing at 3:1, 4:1 and 5:1 push angles.

Jan 1, 2006

By R. Abela

Heavy mineral sands are usually beneficiated in a spiral concentrator circuit prior to separation of heavy minerals into streams of zircon, rutile and ilmenite. The performance of the spiral concentrators is heavily affected by the presence of slimes in the rougher feed. The paper quantifies the effect of slimes content and discusses the beneficial effect of spiral feed de-sliming. The net effect of inefficient slimes removal can cause significant recovery losses of the heavy minerals present in the feed.

Jan 1, 2003

Abrasivity and wear resistance are not intrinsic properties of materials, but rather parameters describing the interaction between the wear part and the material exerting the wearing action. Moreover, wear or, at least, that part of the wear which is due to the cumulative effect of minute scratches, is linked to the hardness disparity concept. Abrasivity, in this context, is a relative concept, pertaining to a metal-rock pair, rather than to a rock. Based on this assumption, a methodology has been developed and checked against actual cases, enabling description of the abrasiveness of a rock or the abrasion resistance of a metal through the ratio of comparable quantitative indicators. The paper describes the methods and provides examples of applications to practical cases (namely: rock cutting, excavation by means of tunnel boring machines (TBMs), rock crushing, and hydro-mill cutting).

Jan 1, 2012