Search Documents

By J. W. MacDonald

Review of equipment, performance, and shaft design plans including head-frames for sinking and forms for lining are given. Also included are comparative data for shafts of 11 x20 ft and 193/4 x 30 ft with 756 and 666-ft depths, respectively. Advantage from curtain wall installation with "slip forms" which warrant consideration for normal lining are outlined. A preliminary review is also made of "chemical grouting" to stop water inflow leakage with Halliburton equipment and service. Two coal mine shafts recently completed in Franklin County, Ill., afford experience and accomplishment to warrant review. These shafts provide access to a tract with a potential recovery of one hundred million tons. This work provided the initial sinking by other than a contractor's organization since 1918. Four additional shafts required during the interim were sunk under contract arrangement with others. Supervisory contact and inspection afforded experience to govern planning and conduct of the recent work. TEST DRILLING Core test holes were drilled within each of the two shaft locations. Four additional cable tool holes were drilled on a radius of 700 ft from the shaft bottom to determine the coal seam elevations and govern the underground layout plans for each shaft. A graphic log of the hoist shaft test drillhole is shown by Fig. 1. A very soft sandstone was found at a depth of 16 ft. Cored recovery of the sandstone proved much weaker than the overlying compacted sand secured with coring facilities for soil recovery. Gradation from the very soft sandstone to fairly hard material occurred with the next 14 ft, extending to a depth of 30 ft. The weak character within the upper portion entailed need of adequate protection when sinking as described later. A part of the sandstone provided sufficient porosity and permeability to warrant further investigation. Adjacent cable tool drilling for temporary water supply disclosed inflow was limited to 2 gpm with a depth of 40 ft. It was increased to 12 gpm during the next 50 ft of drilling and occasioned subsequent precaution when sinking. General arrangement of facilities for sinking the hoist shaft is shown by Fig. 2. An available steel frame building was used to accommodate the hoist, compressor, shop, and shower or change room. The stiff leg derrick with 90-ft length of boom permitted removal of forms from the wood shop to the storage area or delivery within the shaft. Reinforcing steel and other needs were similarly handled, in addition to headframe erection. The headframe was placed over one end of the shaft to enable passage of forms for lining through the adjacent half next to the stiff leg derrick. The steel headframe as shown by Fig. 3 was fabricated locally. Side anchored cables from the

Jan 1, 1961

By Thomas M. Barczak

The intent of this paper is to make mine operators and engineers aware of parameters which affect the loading behavior of passive roof support systems. The strength of a passive roof support element alone is not a meaningful measure of support performance. Passive roof support elements and the surrounding strata act as a system, responding to changes in the physical mine environment due to the extraction of coal and associated redistribution of stresses. The load- ing of a passive roof support element is a function of the stiffness of the roof support structure; a stiffer structure will react a higher load to a converging mine roof than will a more flexible structure. If the stiffness if the support structure is not properly designed, excessive loading will result due to the displacement of the mine roof, causing premature failure of the support. Ideally, the yield strength of a passive support needs to be no greater than that required to support the dead weight of the immediate mine roof, providing the post yield characteristics of the support are compatible with the irresistible convergence of the overburden strata and the support system continues to provide this resistance after reaching its yield load. Idealized design considerations for passive roof support systems in terms load-displacement characteristics discussed. The stiffness and yield characteristics of wood concrete cribbing, as determined controlled tests in the Bureau's Roof Simulator, are compared preliminary recommendations passive roof support utilization also provided.

Jan 1, 1987

By P. A. Hagerty

Biological treatment of metals-impacted water using sulfate reduction is a viable means of treatment that has been applied in pilot and full scale at numerous projects. One of the fundamental challenges with this type of treatment is the selection of an appropriate substrate to support the sulfate reduction process long-term. The substrate degradation products provide a carbon source and an electron donor for metabolism by sulfate-reducing bacteria and consequently organic characteristics are critical; however, the physical attributes of the substrate are equally critical to an efficient and optimized substrate mix. This paper explores the affect of particle size (a.k.a. grain size) of several substrate mixes on the treatment efficiency of sulfate reducing treatment systems. Substrate selection can be separated into two phases of evaluation, the primary selection phase and the secondary optimization phase. The primary selection phase considers such fundamental attributes as source availability, economics, bioavailability and longevity. These fundamental activities are conducted in order to identify potential candidate ingredients of the substrate mix which are regionally available, economically viable and consistent with the biogeochemical aspects of the project. Recent work has been conducted in the development of testing protocol for organic substrates to quantify bioavailability (Martinez Hernandez et al. 2010, Place et al. 2006) as part of the primary selection phase. Once the substrate ingredients have been selected based on the primary criteria, the mixture of these ingredients is then developed based on an optimization process, including consideration of the substrate ingredient?s particle size distribution.

Jan 1, 2011

By Enrique Castells

La extracción del mineral es el método más habitual para la explotación minera y se realiza a través de rampas, galerías, y túneles que permitan el acceso hasta la zona de minado. Sin embargo, cuando se da una excesiva profundizaciión del terreno, se emplea el método de pique vertical ya que logra el acceso de los operarios a las zonas más profundas de un modo más rentable y rápido a través de la extracción del mineral por izado de vagones o skip hasta el de nivel de superficie o intermedio. Por ello, es común que las minas replanteen la sustitución de su sistema de extracción habitual por el de izado por piques. En este sentido, el presente trabajo desarrolla la aplicación de los piques verticales en los sondeos de exploracion de la mina Hullera Vasco Leonesa. La primera parte del proyecto describe la ejecución de dos piques verticales (Aurelio y Emilio del Valle), y la segunda, en la ejecución de más de 17.000 m de galerías y obras de infraestructura de diversa índole.

Sep 13, 2001

By L. T. Isaacs, W. H. Traves

A numerical model for analysing the drainage of fill in mine stopes has been described. The model can be used to analyse the process of fill drainage in existing and proposed mine stopes. The validity and potential value of the model have been established by experience with a simpler, 2-dimensional numerical model and by testing the new model against the earlier model. The new model is more useful than the 2-dimensional model because it allows for heterogeneity of fill material within the stope - a factor that has been demonstrated to affect drainage characteristics significantly. The 3-dimensional model is also capable of predicting pore pressures and drainage rates at specific locations in the stope without the need to resort to 2-dimensional generalisations. Such information, integrated with relevant field data as they become available, will provide valuable mine planning information for the scheduling of filling operations and design of fill mixes

May 1, 1991

By E. H. Boswell, E. M. Cushing

The Mississippi embayment east of the Mississippi River is part of a vast geologic and hydrologic province. The abundance of water available is largely responsible for the agricultural history of the area and is perhaps the key factor in the rapidly accelerating trend toward industrialization. The multiple artesian aquifer systems that underlie the region and the alluvial aquifer along the Mississippi River are virtually undeveloped sources of fresh water in that they are yielding only a fraction of the water available. The potential yield of the 12 aquifer systems is estimated to be about 25,000 mgd (million gpd) of which only about 600 mgd is presently being withdrawn. The amount of water in storage in these systems is about 1600 trillion gal. Ground water having a dissolved-solids content of less than 500 ppm is generally available at depths of less than 1000 ft, and water having a dissolved-solids content of less than 1000 ppm is available in some places to depths of more than 3000 ft. Iron is the most common troublesome chemical constituent in the ground water. Water in varying amounts is also available from streams within the region. The amount of water which originates within the region and which leaves it as streamflow during a year averages about 50 million acre-ft (about 45,000 mgd). An additional 375 million acre-ft (about 340,000 mgd), which originated outside the region, leaves the region as streamflow during an average year. Some streams have considerable flow during periods of no precipitation and the water during these periods generally has a low dissolved-solids content. Large quantities of water from streams and waterbearing sands (aquifers) are available in the Mississippi embayment east of the Mississippi River. Most of the region is underlain by aquifer systems that will yield large quantities of water to wells, making ground water the most readily available source of fresh water. About 90% of the water used in the region is obtained from wells. Streams have been used primarily to dispose of, and dilute, wastes that have been dumped into them. The Mississippi, Ohio and Tennessee rivers, and the lower parts of the Tombigee and Yazoo rivers also serve as a means of transportation. This nominally water-rich region receives from 48 to 56 in. of precipitation in average years and is crossed by several large rivers. The largest, the Mississippi River, is the western boundary of the region discussed in this paper. The economy of the region is basically agricultural, but industry has become increasingly important since World War 11. The diversification and mechanization of agriculture have resulted in a surplus of manpower, most of which is being absorbed by the expansion of industry. Further industrial expansion probably will occur because of the available manpower, natural resources and economical transportation. Increasing demands on available water supplies will be made and the future economic growth of the region will be largely dependent upon wise utilization and management of the water resources.

Jan 1, 1969

By D. W. Zandee

"IntroductionHaving mined an economic mineral bearing rock which is of insufficient grade to warrant direct smelting, upgrading or beneficiation is required to make it an economically viable ore. The first step in effecting the concentration process is comminution or sequential breaking of the rock to allow liberation and subsequent recovery of the desired mineral particles. Desirably the ore could be broken down to the point where the valuable mineral is completely liberated to maximize the chance of recovering as much of it and in as pure a form as possible. The number of energy intensive stages of breakage required to attain this goal depends on many physical characteristics of the ore such as hardness, friability, toughness, grain size, existing fracture planes and particle shapes.Commonly the distinct stages are primary, secondary and often tertiary crushing and finally grinding. To increase the efficiency of each stage of size reduction, pre-treatment sizing is common.Crusher feed is commonly scalped of large pieces or screened for reduction crushers and classified for secondary grindingcircuits.Although crushing and screening is employed for many different products, this chapter reviews current practice in larger tonnage metalliferous ore treatment plants.Current practice is to use large gyratory or jaw crushers for primary crushing and some sort of gyrating or cone crushers for additional stages of reduction. For autogenous or semiautogenous grinding circuits only the primary crushing stage is necessary, the balance of the work being performed in the grinding stage. For conventional grinding circuits using ball mills or combinations of rod and ball mills, secondary, tertiary and even quaternary crushing stages are normally required.Older type crushers such as stamp mills, double rolls, sledging mills and hammermills are no longer common but are used for small tonnage special processes.Important to efficient crushing are a variety of sizing devices such as grizzlies and vibrating screens. Products at different stages must be stored to give surge capacity and allow controlled feeding rates through mechanical and gravity feeders. These storage piles, bins and feeders as well as crushers and screens are commonly integrated into a total facility by means of conveyor systems. Most often these are endless rubber belts driven by simple or multiple drive mechanisms usually consisting of electric motors and speed reducers."

Jan 1, 1989

Despite the current economic downturn that is now decimating iron ore production, Minnesota?s mining operators remain optimistic about the long-term prospects for the industry. Reflecting this optimism, the development of several new mining projects continues in the state. The future of mining in Minnesota was the featured topic at the combined 82nd Annual Minnesota Section of SME Meeting and 70th Annual University of Minnesota Mining Symposium. More than 500 mining industry professionals, including engineers, executives, mining managers and equipment suppliers from the around the world, attended the meeting, which was held April 14 and 15, 2009, in Duluth, MN. The combined meeting featured a keynote session with three distinguished speakers plus a panel discussion by representatives from several of Minnesota?s taconite producers. The keynote speakers were Curtis Clark, president and chief operating officer, Behr Dolbear, who gave a presentation on the ?State of the Mining Industry.? Phil Newman, chief operating officer, CRU Strategies, spoke about challenges facing the mining industry and James A. Skurla, acting director, Bureau of Business and Economic Research, Labovitz School of Business and Economics, University of Minnesota Duluth, discussed the importance of mining to northeastern Minnesota?s economy. The taconite producers panel discussion included Jonathan Holmes, vice president and operations manager, ArcelorMittal; Ed Latendresse, vice president and general manger, Hibbing Taconite; John Tuomi, vice president operations services, United Taconite and Mike Mliner, vice president and general manager, Northshore Mining. The mangers provided updates on their respective operation The meeting included concurrent technical papers sessions on mining, processing, environmental and nonferrous mining. The sessions included technical papers that provided information on the status of a number of new mining projects in the state. The conference also offered a SME short course titled ?The basics of iron mining.? A tradeshow that featured about 100 companies and organizations offering products and services to Minnesota?s mining industry ran in conjunction to the conference. It was estimated that more than 900 people, including conference registrants and special invited guests of the vendors, attended the tradeshow opening reception. This was the largest trade show in many years. The Minnesota Section of SME also held its annual business meeting during the conference.

Jan 1, 2009

By D. F. Scott

Seismic tomography, as used in mining, is based on the principle that highly stressed rock will demonstrate relatively higher P-wave velocities than rock under less stress. A decrease or increase in stress over time can be verified by comparing successive tomograms. Personnel at the Spokane Research Center have been investigating the use of seismic tomography to identify stress in remnant ore pillars in deep (greater than 1220 m) underground mines. In this process, three-dimensional seismic surveys are conducted in a pillar between mine levels. A sledgehammer is used to generate P-waves, which are recorded by geophones connected to a stacking signal seismograph capable of collecting and storing the P-wave data. Travel times are input into a spreadsheet, and apparent velocities are then generated and merged into imaging software. Mine workings are superimposed over apparent P-wave velocity contours to generate a final tomographic image. Results of a seismic tomographic survey at the Sunshine Mine, Kellogg, ID, indicate that low- velocity areas (low stress) are associated with mine workings and high-velocity areas (higher stress) are associated with areas where no mining has taken place. A high stress gradient was identified in an area where ground failed. From this tomographic survey, as well as four earlier surveys at other deep underground mines, a method was developed to identify relative stress in remnant ore pillars. This information is useful in making decisions about miner safety when mining such ore pillars.

Jan 1, 1996

By P. Wearden, K. Bryner, K. Vrana, V. Castranova, R. Dey, R. Reist, J. Blackford

"Summary: Fibroblast proliferation and enhancement of collagen synthesis are key steps in the development and progression of pulmonary fibrosis. The current investigation presents a fibroblast proliferation assay to detect the release of competence factors from pneumocytes. The specific objective of this study was to define cell culture conditions for fibroblasts that would allow selective detection of competence factors in test media. The results indicate the following: (a) fibroblasts should be cultured for 2 days in plasma-free medium rather than 2% plasma to assure complete quiescence; (b) 1% plasma was optimum for producing progression activity for the bioassay of a competence factor, while 0.5% plasma did not produce sufficient progression activity (yielding false negatives) and 2% plasma often contained significant competence activity (yielding false positives); and (c) fresh plasma should be used since the progression activity of plasma was adversely affected by freezing and thawing. Under these conditions, this bioassay can be employed with either rat or human lung fibroblasts to detect competence factors such as platelet-derived growth factor (PDGF), at levels as low as 25 ng/ml.Fibrotic lung disease, as a consequence of occupational exposure to silica dust. is characterized by the development of concentric hyalinized nodular lesions in the lung and the progressive loss of pulmonary diffusion capacity. Proliferation of pulmonary fibroblasts and enhanced synthesis of collagen by these pneumocytes have been shown to be key steps in the development of chronic silicosis ( 1 ). The regulation of lung fibroblast proliferation by cytokines released from alveolar macrophages may be an important pathogenetic mechanism in the development of the fibrotic process (2). Some cytokines stimulate fibroblast proliferation by activating specific phases of the cell cycle (3,4). In particular, platelet-derived growth factor (PDGF) promotes fibroblast proliferation by inducing the movement of quiescent (G0 ) cells into the G1 phase of the cell cycle (5). Insulin-like growth factor (IGF) and transforming growth factor-P (TGF-P). on the other hand, regulate the rate of transition of fibroblasts from G 1 into the S phase (5,6). These two classes of cytokines have been termed competence and progression factors, respectively. One approach used to examine the release of cytokines from macrophages is the fibroblast proliferation assay in which quiescent fibroblasts are exposed to culture supematants from macrophages exposed to various stimuli. In most of these assays, the supernatant contains fetal calf serum (FCS), which provides the competence factor(s) necessary to facilitate the proliferation of fibroblasts (7-9). Recently, a fibroblast proliferation assay using platelet-poor .plasma [lacking competence factor(s)] as a substitute for FCS bas been described (I 0, 11 ). In this assay, the release of a competence-inducing PDGF-like growth factor from rat and human macrophages can be distinguished from other cytokines that act as progression factors."

Mar 1, 1992

By J. Finch, R. McIvor

This paper presents the development of a new grinding circuit steady-state modeling system. It is fundamentally based on the “functional performance equation”, which has now been used to improve the performance of numerous grinding circuits. This equation characterizes the two distinct efficiencies that are at work in a ball milling circuit, and how these relate to overall circuit productivity. It does so based on the particle size chosen to distinguish between coarse and fine (product size) material. Now, by applying it to all the material size classes, a simple yet reliable ball mill model was created. Combined with cyclone recoveries, the complete, detailed grinding circuit performance can be exactly reproduced mathematically by the computer program. It can then be used with separate process equipment application engineering methods to systematically engineer grinding circuit improvements. The development, features, uses and limitations of the system are described.

Jan 1, 2007

It is possible to divide industrial minerals into four general categories: 1. fuels, 2. construction materials, 4. agricultural minerals, and 4. industrial minerals. It is proposed to ignore the fuels in the context of this paper and deal in general terms with the others. Mining companies have often considered getting into the industrial mineral business because they can see a resource development with good growth and consistent profits. However, many mining companies being conversant with the metallic side of the industry have spent sleepless nights determining which industrial minerals are most suited for their particular situation. Some have got into the business for the wrong reasons and wished they had never heard of it. Others have successfully adapted to the industrial minerals philosophy and now operate in both metallic and industrial mineral arenas. There is a large difference between firstly, the philosophy and secondly, the functions of being in the industrial minerals business as opposed to metallicÆs. The philosophies can be considered in parallel but it is necessary to clearly have an appreciation of the dominant influences that affect industrial minerals.

Jan 1, 1984

By P. O'Connell, J. Lever, C. Clemence

The Bulyanhulu Mine, Tanzania is constantly trialing ideas for improvements in the drill and blast process. The project work has resulted in a large number of choices in explosive type and charging methods being available for blast design. Interestingly, though booster sensitive bulk emulsion had been introduced to the site to reduce dilution, better results were being obtained from reduced charge columns (decoupled columns of poured anfo in 50mm pvc pipe) and pneumatically loaded anfo upholes, which had been traced. In order to compare the explosive type and charge up-methods, an explosives comparison trial was performed.

Jan 1, 2006

By G. Richards

Research shows that having more women in the top mining jobs can bring bottom-line benefits. Mining companies are starting to embrace the need for greater gender diversity at board and senior management levels, figures and examples are given.

Jul 1, 2015

By J. Sliwinski, J. Oliveira

"The application of geometallurgy and corresponding sample selection can take on several formats within industry. Current practice can range from a strictly geostatistical approach to one in which geological and metallurgical parameters are used in combination to create a representative sample selection strategy. The stage of a project and the level of information available at the time of sampling influences the methodology used to create a representative sample.A geometallurgical study of Carpathian Gold’s Rovina Valley Project in Romania is used to demonstrate a sample selection strategy that integrates geological, mineralogical and metallurgical data to maximize the relevance of the geometallurgical unit definitions. This approach, practiced by Xstrata Process Support for its’ clients, ensures that the results of the metallurgical program can be interpreted in the context of these units.INTRODUCTIONGeometallurgy is a cross disciplinary approach in which metallurgical performance of an ore is linked to intrinsic geological and mineralogical characteristics. The objective of a geometallurgical study is to characterize the range of metallurgical performance of an orebody. This allows the geoscientist or metallurgist to create a robust flowsheet able to treat the full range in variability and to develop production strategies to maximize financial performance. The standard approach is to individually sample and test a series of ore types or geometallurgical units. Several different approaches are used in industry to define what constitutes geometallurgical units and how to sample them.One current methodology is the use of multivariate statistics. Geochemical data along with available geological data are used to define multiple variability domains (Williams, 2004; Walters, 2009). There are risks associated with this methodology since the extent of the data set itself may not support a purely statistical approach at the time that metallurgical units need to be defined. The assay suite collected by exploration programs is often limited to pay metals while metallurgical performance is often affected by ore gangue components. Furthermore, in many cases metallurgical scoping and pre-feasibility studies take place prior to the availability of extensive geochemical data sets. Purely statistical methods can produce multiple populations which require extensive sampling, testing and validation prior to consolidation into a reasonable number of composites for metallurgical testing. Methodologies are therefore required that allow representative sampling and testing of consolidated geometallurgical composites to occur at various phases throughout the development of a mining project."

Jan 1, 2013

By Marc D. Melker, Geoffrey R. Lane, Michael Jahraus

"The Cresson gold deposit is located in the Cripple Creek district of Colorado. The deposit is composed of volcanic intrusive rocks and volcanogenic sediments where gold mineralization is associated with veins and cavities within a diatremal breccia.The purpose of the current study was to:1. Determine the penetration potential of the Cripple Creek Breccia.2. Assess the relationship between penetration and gold recovery within the Breccia.Two methods were applied using a cyanide solution containing ultraviolet sensitive dye to elucidate pathways of penetration within the rock. The first involved stagnant soaking of twoinch square pieces within the solution. The second method involved column leaching of ~100kg of Breccia crushed to P80 12.7 mm (0.5 inch). Samples were selected at specified intervals to capture the penetration progress of the solution. Photomicrographs and image analysis were utilized to illustrate and quantify the degree of penetration.Results indicated that the maximum penetration for the Cripple Creek Breccia (85 to 97%) due to a porous and permeable groundmass, containing large non-porous lapilli fragments. In addition, ~90% of leachable gold was recovered with only ~50% rock penetration.INTRODUCTIONDye penetration studies were first developed at SGS-Lakefield Research for the purpose of determining the fluid penetration amenability of differing rock types. The method was to place a large rock or drill core in a pan with 1 to 2 inches of a pre-mixed, water based fluorescent dye. The sample was sequentially cut after prescribed time periods to reveal a fresh surface. The cut surface was photographed under long wave ultraviolet light, and the same piece returned to the dye and allowed to sit until the next prescribed cutting."

Jan 1, 2006

Jan 1, 1970

By J. M. Simard, S. Morissette, P. Coursol, P. Mackey

A new, powerful model is presented that focuses on plant logistics and scheduling aspects of the smelting, converting, fire refining and casting operations at the Horne smelter. This plant complex is the largest custom copper smelter in North America. It handles a wide range of feeds and utilizes a number of proprietary continuous and batch technologies that require good scheduling in order to maximize plant capacity and efficiency. The present model was developed by Xstrata Process Support, in collaboration with the Horne smelter, and uses the Arena® software to evaluate the impact of a number of plant variables on the annual copper capacity of the plant. Model development was carried out by Xstrata Process Support, in collaboration with the Horne smelter, through the effective combination of process chemistry knowledge and detailed knowledge of the plant operation (including all material flows and transfers, as well as information such as operating on-line times, plant stoppages and also scheduled and unscheduled maintenance activities). A number of case studies were then examined, including the impact of anode furnace and casting cycle times on annual copper capacity and the impact of a one-crane mode of operation in the converter aisle, which normally operates with two cranes in service. The model predictions were found to match actual plant results very well. The present modelling of plant logistics and the scheduling aspects were found to add important dimensions at the plant with regard to projections of the real-life plant capacity. As demonstrated in the present case, this type of model and application can have a significant impact on optimizing operations at a given plant. This impact is particularly important in the current market environment, where emphasis is on maximizing plant output and lowering costs. These models can help yield the easily obtained gains that are clearly desirable in these times. Xstrata Process Support has developed Arena models for other operations and is available to explore new applications for a win-win situation at other plants, including mines and concentrator operations.

Jan 1, 2009

By M. I. F. S. Cruz, R. Pedersen, F. J. A. S. Barriga, A. Dias, A. F. A. Marques

"Underwater hydrothermal vents are known since the 1970s and their importance for the global economy is growing as new discoveries and new assessments are made each year (Cherkashov et al., 2010; Corliss et al., 1979). The similarities of seafloor massive sulfides, representing the younger versions of the well exploited on land volcanogenic massive sulfides, bring an increased awareness to the potential of the sea (Ajan G. Galley, 2007; Hannington et al., 2011; Herzig and Hannington, 1995). The Arctic Ocean presents itself as an opportunity to study new interest areas and numerous hydrothermal systems (active and inactive) were discovered along the Arctic Mid Ocean Ridge (AMOR) (Pedersen et al., 2010b). The Mohns ridge is an ultraslow spreading ridge of the AMOR (Vogt, 1986) where two hydrothermal vent sites were recently discovered, the Jan Mayen and the Loki’s Castle (Pedersen et al., 2010a; Pedersen et al., 2009; Pedersen, 2005). Here we compare these two Arctic hydrothermal systems, which represent two well-differentiated end-members of hydrothermal fields in the region."

Sep 1, 2014

By Forrest T. Moyer

INJURY experience and related employment information are presented in the chapter for the coal-mining, coking, oil and gas, peat, and native asphalt industries in the United States for 1964. No attempt has been made to combine these data and present injury-frequency rates reflecting the mineral-fuel industries because the hazards of the separate industries are not comparable. All rates in the text are calculated separately on data before rounding, hence component rates may not add to the total rates shown in the tables. Tabulations showing the trend of injuries and employment for all mineral industries are presented in Volume III. COAL Injury experience of the coal mining industry was improved in 1964, as measured by the declines of 1 and 14 percent, respectively, in the frequency and severity rates. Although the total number of injuries increased in 1964, a slightly greater proportional increase in man-hours worked caused the frequency rate to drop to 44.65 per million man-hours. The injury-severity rate in 1964 was 7,832 days lost per million man-hours of exposure. Employment and injury data for 1964 are based on final data for anthracite mines and preliminary data for bituminous coal and lignite mines. Fatality experience improved significantly with a record low number of 240 deaths in 1964. This total was 44 less than in 1963. The Nation's coal mines during 1964 were free of major disasters (a single accident resulting in the death of five men or more) for the first time since 1956. The

Jan 1, 1965