Search Documents

By R. Franfield

This paper describes a situation that many drilling and blasting contractors have found themselves in – a client?s fear of the use of explosives. In the summer of 2007 Blasting Services Ltd was asked to undertake some drilling and blasting work in an abandoned quarry that was being restored for a housing development. Previous quarrying operations had left a series of overhangs that were considered unsafe and required removing. The site contractor considered that the best and safest way to carry out this work was by drilling and blasting. Blasting Services Ltd, with the technical assistance of Exchem Explosives, designed a drilling and blasting regime to accomplish this work with a series of trim blasts. The design took into account the close proximity of a structure in very poor condition and the imposed vibration limit of 6.0 mm/s (0.24 i.p.s.). The faces were profiled, holes drilled and explosives ordered. A few days before the first blast was due to be carried out the client decided that the poor condition of the nearby structure meant that the use of explosives could not be permitted. This decision was made despite the blast design indicating that the vibration level would be well below the 6.0 mm/s (0.24 i.p.s.) limit.

Jan 1, 2009

By Richard R. Klimpel

Introduction Froth flotation is one of the most common unit engineering operations in use today. Its aim is to upgrade the quality of coal by removing ash/pyrite and separating selected minerals from undesired gangue materials. Flotation has been successfully practiced at the industrial scale for more than 50 years. Its use is increasing due to the ever decreasing feed grades of the coals and minerals being processed. Flotation has also shown itself to be a flexible process that lends itself well to many solid/solid separations. Thus, with surprisingly little equipment modification, separations can involve very different particle sizes and densities, and relative weight ratios of materials to be separated. In addition, the flotation process is economic, especially when compared to size reduction, its associated precursor process. Flotation also lends itself to continuous operations with a given equipment configuration. The operation must exhibit an ability to vary feed rate of solid to the process by as much as 50% without a total collapse of separating efficiency. In addition, the mechanical flotation cell is scaleable from 2.8 to 57 or 85 m3 (100 to 2000 or 3000 cu ft) with surprising ease relative to other unit engineering operations over the same relative size increase. The separating medium used is water. Most of the chemicals required - pH regulators, frothers, collectors, activators, and depressants - are all relatively inexpensive and common. They are not usually used in large quantities. Froth flotation is certainly one of the most versatile and forgiving unit operations in the chemical, mining, and agricultural industries. The problem with the industrial flotation process is that it is fairly easy to get reasonable results and relatively difficult to get excellent results. Why is it so difficult to fine tune the froth flotation process? There are some obvious reasons and a few not-so-obvious factors. The obvious category would certainly contain the tendency of natural feed materials (ores and raw coals) to have variable physical, metallurgical, and surface properties. This occurs even when special care is taken to minimize such differences with blending. There is another obvious reason for difficulty. An inherent broadness of the feed particle size range to flotation results from using any of the common industrial-scalefine grinding devices - ball-, rod-, or autogenous mills. Research has been done into the chemical reagent and equipment aspects of flotation. It has shown strong interactions (limitations) of chemical reagents and equipment on larger and smaller particles. The point is that current flotation practice works best on average- or medium-sized feed particles. The greater the amount of large or small particles, or of both large and small, the more difficult it is to achieve excellent flotation results. Other reasonably obvious factors include: • variations in mineral type and liberation sizes; • water chemistry variations such as those involving Ca", C03, or Fe", or various soluble metal cations; • the presence of stray organic materials such as returning soluble reagents or partially degraded reagents in reuse water; • the lack of reliable on-line instrumentation for monitoring and control; • frequent equipment malfunctions of all types; • excessive feed rates for installed plant capacity; • poor operator interaction with the process; and • poor reagent dosage control. There are less obvious, but real limitations to flotation. These are inherent in the design and operating characteristics of the most common cell design in use today - the mechanical flotation cell. Individual performance attributes of the chemical reagents used, along with their manner of use, also carry limitations. The bulk of this paper will deal with chemical reagents and their use. Chemical reagents In 1979, the author and his co-workers were asked to invent and implement, at the industrial scale, new flotation reagent chemistry. After reviewing some of the literature (Sutherland and Wark, 1955; Klassen and Mokrousov, 1959; M. Fuerstenau, 1962; D. Fuerstenau, 1976; and Leja, 1982), a series of carefully controlled plant scale tests were set up. These tests were designed to understand existing reagent scale-up from the laboratory to the plant. They were to quantify at the plant level the effect of some of the more important, controllable chemical reagent factors (frother and collector type, frother and collector dosage, pH effects). This is a learning experience that all researchers involved in flotation theory should experience. It quickly became apparent that: • because a factor is important

Jan 12, 1988

Open pit mine plans define the complex strategy of displacement of ore and waste over the mine life. Various mixed integer linear programming (MILP) formulations have been used for production scheduling of open pit mines. The main problem with these models is the inability to solve real size mining problems. We present a mixed integer linear programming formulation for the open pit long-term production scheduling problem. To reduce the number of binary integer variables in the formulation, we aggregate blocks into larger units referred to as mining-cuts. We present a semi-supervised clustering algorithm which aggregates smaller blocks based on rock types and grade ranges into mining-cuts without introducing an error in the grade estimated values. The cluster-based aggregation algorithm is fully integrated into an MILP mine production scheduling prototype software. We have implemented, verified, and validated our models. The efficiency of the new platform is evaluated through iron ore mine case study.

Dec 6, 2010

By David G. Dixon, Maziar Eghbalnia

"Gold and silver nanoparticles (NPs) were deposited on pyrite at ambient temperature from colloidal solutions prepared by reduction of hydrogen tetrachloroaurate or silver nitrate by sodium sulfide or sodium tetrahydridoborate. The nanoparticles were characterized using Ultraviolet-Visible (UV-Vis) spectroscopy and the experimental spectra were fitted using Mie - Gans modeling. The modified pyrite was investigated using Electrochemical Impedance Spectroscopy (EIS). Electrodes were prepared from both natural and modified pyrite samples and were modeled using an equivalent circuit (EC) based on the EIS data. The comparison of the results revealed a decrease in charge transfer resistance for the ferric ferrous redox couple associated with the modified pyrite. From this behavior it is concluded that the electronic transport between the nanoparticles and the electrode surface over distances in nanometer scale is enhanced. Nanoparticles below a certain size act as quantum dots due to electronic confmement. Decreased charged transfer resistance at the nanometer scale may be caused by electron transport through tunneling mechanism via quantum dots.IntroductionIn recent years, considerable attention has been focused on the synthesis and study of Metal nanoparticles due to their potential applications in the fields of physics, chemistry, biology, medicine, material science and their interdisciplinary fields[!]. When material is nano-sized, the physical properties deviate markedly from those of bulk material, however, this effect is highly dependent on the particle size, interparticle distance, and morphology of the nanoparticles [2].An extremely small region of space defmed in a semiconductor material in order of nanometers is called a quantum dot, a term coined by Reed [3]. The three dimensional confinement of quantum dots can change properties of the excitons in comparison to free excitons in a bulk material [4]. Nanoparticles behave electronically as zero-dimensional (restricted in all three dimensions) quantum dots when the de Broglie wavelength of the valence electrons and the particle are in the same size range.As Reed [3] explains electrons confined in a plane have no freedom to move the third dimension. Those confined in a quantum wire are only free to move in one dimension, and those confined in a quantum dot are not free in to move in any dimension. An electron inside a cube of material IO nm on a side is confined to a point."

Jan 1, 2012

Ferruginous manganese deposits have been known at Ripon Hills since the late 1950s. The main group of deposits occur in an area 6 km by 5 km and these were extensively investigated by Longreach Metals N.L. during1971 and 1972 for possible commercial exploitation.Ripon Hills is a dissectcd fault plateau 350 m above sea level formed by the uplift of a block of gently dipping Proterozoic shales, cherts, and dolomite. The plateau consists of chert breccia which is underlain by massive dolomite. The shales which are ferruginous and manganiferous overlie the chert breccia but are now only preserved, in places, in the broad depression and valleys of the plateau.The ore deposits occur as supergene replacement of the shales and were investigated by geological mapping, grid percussion and diamond drilling, and bulk beneficiation testing. Iron and manganese oxides erraticallyreplace Shale accompanied by the leaching of other minerals. The ore is composed of fine grained pyrolusite intergrown with fine grained hematite and locally containing extensively altered bixbyite and braunite. Thegangue mineral is mainly kaolin.The average grade, using a 15 per cent Mn cutoff, was 19 4 per cent Mn and 25·9 per cent Fe for a combined drill-proven, indicated, and inferred tonnage of 56,000,000 tonnes. The average depth of this mineralization from the surface is 11 m. Using a cutoff grade of 20 per cent Mn the average grade was 24·6 per cent Mn and 23·0 per cent Fe for a combined tonnage of 12,000,000 tonnes to an average depth of 8 m.The substantial drop in reserves occurs because a high proportion of the mineralized material contains less than 20 per cent Mn.It was shown that whereas the lower grade ore, despite erratic fluctuations in grade, could be beneficiated to specification grade by crushing, screening, and conductivity ore sorting, the higher grade ore could be beneficiatedto specification grade by crushing and screening only. The utilization of the higher grade ore was considered to constitute a more viable operation.There is potential for high grade manganese ore to be discovered in the Ripon Hills area at the contact of chert breccia and underlying dolomite.

Jan 1, 1977

By Connie Postupack

The purpose of the workshop is to show the effect of various blasting factors on the overall results.

Jan 1, 1994

By WU Jian-hui

Keywords: metallic material, precursor synthesis, precipitation, nickel, fibrillar powder The composition and morphology of the precursor of fibrillar nanocrystalline nickel powder prepared by oxalate precipitation are characterized by XRD,IR and SEM analysis, and the effects of temperature, nickel concentration, pH, surfactant and drying process on the morphology and the dispersion of the precursor are investigated. By the experiment results, the fibrillar precursor is a complicated nickel salt. The precursor prepared in the of 60~70°C,0.6~0.8 mol/L nickel ion, pH=8.4~8.6 and with addition of PVP surfactant is well dispersive and in fiber form. The powder dried by azeotropic distillation is dispersive.

Jan 1, 2005

By Markus Timusk

This paper describes a research project that focuses on developing a diagnostic routine to assist in decision support for the condition based maintenance of mobile mining equipment subject to unsteady duty. The objective is to develop a general method for initial identification of mechanical faults in machinery operating under non-steady state conditions. The platform to be used for the experimental development and validation of the system is the swing machinery in an electric mining shovel operating in an open pit mining environment. The strategic approach that is proposed for the diagnostic routine will involve using novelty detection augmented by temporal classification.

May 1, 2004

An understanding of the origin of mineral deposits and their relationship to local and global geotectonics is essential if regional targets for mineral exploration are to be chosen. Volcanism, metamorphism and tectonism are especially significant for the origin and emplacement of mineral deposits, which, far from being fortuitous oddities of nature, occupy well defined positions within distinctive lithofacies. Thus, suggestions for mineral exploration targets can be made taking into consideration the position of 'fossil' convergent and divergent plate tectonic boundaries to indicate areas of specific types of mineralisation. To be borne in mind, though, that level of exposure, time and location of magma generation are all additional and important controlling factors. To further understand the importance of the above parameters, one must refer to the concept of paired metamorphic belts (Miyashiro 1973) which develop during an orognic cycle. These belts are generally constructed in such a way that an ophiolite type complex with metamorphic grades related to high pressure and moderate temperature regimes is flanked by an area of calc-alkaline volcanism and granitic activity with metamorphic grades within a region of high temperature and low pressure. The former situation is usually the seat of primary magmatic mineralisation, whereas the latter contains base metal. Deposits of acid plutonic and volcanic association. As will be seen later, this particular metamorphic-volcano-orogenic situation is well developed in some parts of New Zealand. For the present purpose a distribution of potential ores as related to plate tectonic processes is given below:a) Divergent plate boundaries: primary magmatic Ni-Cu, Pt,Cr, PeS2 and Cu, Pb,Zn in hot brines-hydrothermal environments Mn deposits.b) Convergent plate boundaries: stratabound Cu-Fb-Zn-Ag of felsic volcanogenic association. Porphyry eu-Au of island arc type, porphyry Cu-Mo of continental type. Cu, Au, Y, Sn, Hg, Sb of vein type and replacement lode related to granitic activity.c) Au of hydrothermal vein association, related to late dynamo-metamorphic events. By virtue of ocean floor spreading, regions of divergent plate boundaries are eventually juxtaposed or welded n to areas where plate collisions occur. This is then followed by partial melting due to various causes, just above the descending plate; thus creating a zone of acid to intermediate magmatism. The final picture is that of an orogenic zone with the paired metamorphic belts outlined above.

Jan 1, 1976

By Martin B. Hudson, Daniel Brescia, Zhangwei Ning

Due to the complexity and sensitivity of surrounding environments, instrumentation and monitoring (I&M) is critical for many urban deep excavations. The objects to be monitored include shoring bulkheads, retained embankments, adjacent buildings and roads as well as underground utilities. However, there are also plenty of constraints on the implementation of I&M such as: congested site space, difficult access to instruments, coordination among multiple contractors, and installation permits for private or public properties. Because of these constraints, sometimes the implementation of the initially planned I&M is delayed, its scope is reduced, and/or the continuity of monitoring is interrupted. For these reasons, it is important to implement the I&M with robust and redundant capabilities while providing minimal interference to the project construction and schedule. This paper describes state-of-the-art I&M technologies including automatic motorized total station (AMTS) with camera and automatic leveling device, reflectorless AMTS and IoT- based wireless sensors based on a case study of an on-going deep excavation project. INTRODUCTION In urban environments, deep excavations requiring the construction of temporary shoring bulkheads are becoming increasingly common, with the associated need to provide protection of the surrounding built environment during construction. Protection of the surrounding environment requires planning, engineering, construction, monitoring, and excessive shoring movement mitigation. The I&M is a vital component of the deep shoring implementation. In public projects, geotechnical I&M is often placed within the general contractor’s scope, whereas the majority of deep excavations are privately undertaken. For those private developments, sometimes the developer contracts the geotechnical I&M directly with the project geotechnical engineer or by a geotechnical I&M specialist hired by the project geotechnical engineer. In either the public project or private development case, the effective deployment of the I&M system relies heavily on coordination and collaboration with the project contractor.

Jan 1, 2018

By Mark Van Dyke, Ted Klemetti, Joe Wickline

"The identification and mitigation of adverse geologic conditions are critical to the safety and productivity of underground coal mining operations. To anticipate and mitigate adverse geologic conditions, a formal method to evaluate geotechnical factors must be established. Each mine is unique and has its own separate approach for defining what an adverse geological condition consists of. The collection of geologic data is a first critical step to creating a geological database to map these hazards efficiently and effectively. Many considerations must be taken into account, such as lithology of immediate roof and floor strata, seam height, gas and oil wells, faults, depressions in the mine floor (water) and increases in floor elevation (gas), overburden, streams and horizontal stress directions, amongst many other factors.Once geologic data is collected, it can be refined and integrated into a database that can be used to develop maps showing the trend, orientation, and extent of the adverse geological conditions. This information, delivered in a timely manner, allows mining personnel to be proactive in mine planning and support implementations, ultimately reducing the impacts of these features. This paper covers geologic exploratory methods, data organization, and the value of collecting and interpreting geologic information in coal mines to enhance safety and production.The implementation of the methods described above have been proven effective in predicting and mitigating adverse geologic conditions in underground coal mining. Consistent re-evaluation of data collection methods, geologic interpretations, mapping procedures, and communication techniques ensures continuous improvement in the accuracy of predictions and mitigation of adverse geologic conditions. Providing a concise record of the work previously done to track geologic conditions at a mine will allow for the smoothest transition during employee turnover and transitions. With refinements and standardization of data collection methods, such as those described in this paper, along with improvement in technology, the evaluation of adverse geologic conditions will evolve and continue to improve the safety and productivity of underground coal mining."

Jan 1, 2019

By Shamsher Prakash

Equivalent spring constants for analysis of footings is a function of Young's modulus of pile material (Ep), shear modulus of soil (Gs), and geometry of the footing and/or piles. Shear modulus is strongly strain dependent in soils. Therefore, the spring constants are strain dependent, which is acceptable to the Geotechnical engineers. However, structural engineers prefer to use spring constants as a function of displacement, rather than strain. In order to develop these relationships, appropriate relationships between strain and displacement are needed. Also, modulus degradation with strain needs be built into these relationships. Description of spring constants kx , ky, and kz in x, y, and z direction and k?, k?, k?, about x, y, and z directions are relatively simple. However, description of kxø and ky?, the cross-coupling spring constants depend on 2 - components of displacement and rotation. Thus, there are 8 spring constants and likewise there are 8 damping constants. Approximate strain-displacement relationships on which displacement dependant k's and c's are based are presented with appropriate equations, and a numerical example is included illustrating k's and c's as functions of displacement.

Jan 1, 2002

By William S. Heckman

a. When to use: high surcharges, vertical capacity required, limit noise and eliminate vibrations, low headroom, eliminate vibration induced settlements. b. Advantages: eliminates impact noise and vibrations, high section modulus if required, vertical load bearing capacity; corrosion resistant, easy to apply facing for use as a permanent wall, adapts to complex wall layouts, would allow top- down construction, very high uplift resistance. c. Disadvantages: spoil disposal, not water tight, cannot penetrate rock and most obstructions, soil can erode between the piles if surface water and ground water are not controlled, hard to install reinforcing beams over 409 long; subject to high negative skin friction loads, high grout takes in rubble and organic soils. e. Relative cost to other systems: 30% to 50% more expensive than driven soldier piles and lagging except when surcharge loads are involved, or the pile cannot be driven due to noise and vibrations. About the same cost as a sheet pile system. Very competitive if high vertical load must be supported by the wall.

Jan 1, 1997

By Madgwick J. C

Leaching column techniques and microbiological methods have been described in detail in Madgwick and Ralph (1980) and Madgwick, Ralph and Sadler (1981).Sixty-nine kilograms of copper porphyry ore (0.4 per cent Cu, 2.7 per cent Fe) (particle size 2.4-11.2 mm; 60 The effect of sodium chloride (O.6M) irrigation on bacterial leaching of Bougainville copper porphyry ore was studied.Viability of suspended Thiobacillus ferrooxidants was reduced to less than 10 cells/ml in NaCI (O.6M) compared with 10' eells/ml in dilute II,SO, (0.01 M, pll 2). Salt irrigation had no significant effect on heterotrophic and sulphur oxidizing bacteria. Increascd short term recovery of copper (145 g/tonne/ 15 days) was followed by a marked decrease in tenors to less than 20 mg/litre/day compared with an acid leach, steady release, of 110 mg/litre/day. Resumption of acid leaching restored average solution copper to 46 mg/litre/day and the viability of suspended T Ierrooxidates to 10 cells/ml.Quantitative removal of sodium ehloride from ore particles was difficult and t races of NaCI remained for more than 200 days.

Jan 1, 1982

By J. Osterberg

A new device has been developed for load testing driven piles and drilled shafts which consists of an hydraulic jack or bellows which has a telltale rod fastended to the bottom. The rod extends upward to the surface through a pressure pipe. When pressure is applied, the jack or bellows expands, applying an equal upward and downward load at the bottom. The downward movement at the bottom is indicated by the rod and the upward movement is indicated by the movement at the top. Thus, upward and downward load-deflection curves can be drawn. As load increases, failure will occur either in end bearing or friction. Results of field installations are described. Total loads of up to 1,100 tons metric have been used. The method obviates the need for the reaction load required for the conventional pile loading test and separates friction and end bearing. It is especially advantageous for use over water, in crowded spaces and for inclined piles.

Jan 1, 1989

Chalcopyrite concentrate was combusted in oxygen-nitrogen atmospheres, the composition of which ranged from 1-100 per cent oxygen. Factors studied included particle size, experimental temperature and oxygen concentration. The study was assisted by chemical and X-ray diffraction (XRD) analysis and temperature measurements of single particles. Size reduction occurring after melting was found to have a major effect on the overall reaction time. Thus time to attain ignition was largely determined by the original particle size, whereas combustion time was independent of this factor. For particles larger than 40 I'm in air the time to attain ignition predominated. The maximum temperatures measured for single particles were the result of pyrite present in the concentrate. Chalcopyrite did not attain thesame temperatures. Vaporization, either as CU(g) or CuO(g) lImited the temperature. Maximum temperatures measured for single particles of pyrite ranged from 1610°C in 14 per cent oxygen to 2360°C in 100 per cent oxygen (both at 700°C). Measured temperatures were compared with those calculated from a diffusion-based model.

Jan 1, 1983

By Mark S. Sanders

This report presents recommended visibility requirements for continuous miner, shuttle car and scoop operations and details the methodology used to generate them. A task analytic approach was used to define information requirements and visual features which served as sources of information. Information requirements were prioritized and the location of visual features determined. From this analysis, visual attention locations, containing one or more important visual features, were identified. A total of 71 locations-were identified for continuous miners, 54 for shuttle-cars and 54 for scoops. A procedure was developed for assessing whether operators in existing machines could be expected to see the visual attention locations. The procedure makes use of a Human Eye Reference Measurement Instrument (HERMI) designed for this project and an outside-in photographic procedure for documenting compliance with the recommendations. A sample of continuous miners, shuttle cars, and scoops were used to test the procedure. Results are presented in the report.

Jan 1, 1981

By B. Y. Park

This paper develops a series of three-dimensional simulations for the Bayou Choctaw Strategic Petroleum Reserve. The U.S. Department of Energy plans to leach two new caverns and convert of one of the existing caverns within the Bayou Choctaw salt dome to expand its petroleum reserve storage capacity. An existing finite element mesh from previous analyses is modified by adding two caverns and increasing the size of existing Cavern 102. The structural integrity of the three expansion caverns and the interaction between all the caverns in the dome are investigated. The impacts of the expansion on underground creep closure, surface subsidence, infrastructure stability, and well integrity are quantified. The results show that from a structural viewpoint, the locations of the two newly proposed expansion caverns are acceptable, and all three expansion caverns can be safely constructed and operated.

May 1, 2009

By David Siu

Many problems were encountered with the mechanical wedge-type splices used for the 15-inch square precast prestressed concrete piles installed at an industrial plant site. Many of the wedges were breaking during installation of the splices and after pile driving resumed following splicing. Dynamic monitoring of the piles and uplift loading tests confirmed that the problems were associated with cracked or damaged wedges. More ductile, annealed wedges were subsequently used, and, while not completely satisfactory, they were found to perform better than the original more brittle wedges. Introduction Long precast prestressed concrete piles were installed to support heavy, settlement-sensitive structures at an industrial plant in Port Alberni, British Columbia, Canada. The piles were driven through soft compressible silts and clays to toe bearing in a dense sand and gravel deposit or on bedrock. Each pile consisted of two or three segments joined with mechanical wedge-type splices trademarked DYN-A-SPLICE. Shortly after construction began, problems arose during pile installation, and these problems were, later, identified to be related to the wedges, or clamps, used to connect the splice plates.

Jan 1, 1991

Unrelieved residual strains can influence the states of stress in rock masses. If cheap, stable structures are to be constructed in Tock in which large pressures are exterted by unrelieved residual strains, the pressures must be either utilized or neutralized. A photoelastic technique has been used to show that the release of residual strains in rocks is influenced by the mechanical properties of anisotropic rock fabrics. The relationships between directions of residual strain release and the attitudes of minor geological structures have been determined. For engineering design purposes it is possible to estimate the principal stress directions in rock containing unrelieved residual strains if the attitudes of such minor geological structures as foliation planes, lineations, and joints are known.INTRODUCTIONQuarry workers have long been aware that near-surface rocks may be highly stressed. In many cases the stresses are too large to be the result of gravitational loads. Dale (1923, pp. 34-35) gives many instances of deformation produced by the violent release of residual strains in quarry rocks. Coates (1963) has described powerful rock bursts and cases of rock deformation underground implying the existence of much larger stresses than are likely to result from present-day gravitational loads. The only explanation is that pressures of up to several thousands of pounds per square inch may be caused by unrelieved residual strains in rock.Instruments have been developed for measuring states of stress in rock masses. Most stress determinations in rock have been made on the assumption that rock behaves as a simple elastic material. It is now known that rock is a...

Jan 1, 1964