Search Documents

By Robert McClure

The detection, recovery and disposal of commercial explosives and explosive waste has always carried a level of risk and requires specialized equipment and technical expertise. Improperly stored, discarded, deteriorated, misfired, stolen or surplus products are often the primary sources of explosives that require safe disposal. Detection and disposal tools available today have advanced significantly due to developments in Counter-Improvised Explosive Devices (C-IED) operations and commercial blasting technology. These technologies have provided safer more efficient ways to detect, investigate and dispose of commercial explosives products in order to minimize property damage and potential harm to disposal personnel and the general public.

Jan 1, 2015

By Ian Orford, Peter Radziszewski, Lud Strah

"An autogenous grinding circuit was commissioned at the Brunswick concentrator in October 1998. The AG mill was subsequently converted to SAG operation in May 1999 for a number of reasons. The mill had 48 rows of the NORCAST top-hat integral lifter/liners configured in Hi-Lo mode. A charge motion simulation study, the results of which are the subject of this presentation, was initiated to develop a better understanding of SAG mill behaviour. Using a design of experiments approach, a lifter face angle was determined that would increase mill power draw. Once determined, lifter profiles were modified and installed in July 2001, and a second set installed in February 2002. Resulting changes in mill power consumption are presented.INTRODUCTIONThe Noranda Inc. Brunswick Mine, located near Bathurst, New Brunswick, is a large lead/zinc mine and began milling ore in 1964. The ore is massive sulphide with approximately 20% valuable minerals, 60% pyrite and 20% silicates. In October 1998, an autogenous grinding circuit was commissioned at the Brunswick concentrator (Cooper, Orford, Larsen, 2001).At the time, the autogenous grinding circuit replaced existing surface crushing plants, fine ore storage, rod mills and primary ball mills. The 8.54 m diameter x 4.27 m long (EGL) ANI mill was subsequently converted to SAG operation in May 1999.The mill had 48 rows of the NORCAST top-hat integral lifter/liners and was operated initially with all shell lifters at the same height. Following problems with packing and abnormal wear pattern, the profile was changed to a high-low configuration.Further, it was found that over the life of the lifters, mill power draw and throughput varied considerably. Although a change in mill power draw was expected following lifter replacement (predicted during mill design to be in the order of 300-400 kW), the replacement of the worn lifters with new high lifters resulted in mill power draw decreased by some 1000 kW."

Jan 1, 2003

By Tristan Worsey, Nathan Rouse, Kyle Hall

Drilling accuracy is the foundation to any successful blast operation. Even the best blasting practices cannot overcome poor drilling and still obtain desired results. Inaccuracies in boreholes can result in flyrock, increased vibration, uneven floor, and other undesired effects. As depth increases, variation in actual burden and spacing is expected even if collars are located precisely. Problems arise when this deviation reaches a point where it adversely affects the function of the blast design. Not only can unsafe conditions such as insufficient burden at the face develop, but poor fragmentation can compound adverse effects. As with any troubleshooting, problems cannot truly be fixed if they cannot be measured. As a result, significant work has been done in the past on this subject. Currently, there are both cheap and expensive methods used to quantify deviation for a given borehole. However, implementation of these techniques is limited. In general production blasts, little is known about the variance in designed versus true borehole geometry. This is especially true if the blaster does not see telltale signs of drilling deviation. However, losses in blast performance may exist and provide an opportunity to obtain better fragmentation and reduce fines. As drill and blast operations strive for better optimization, greater focus is being placed on drilling accuracy and solutions to this problem. The following paper details the use of several current methods for deviation measurement in order to help prevent compromises of safety and improve overall blast performance.

Jan 1, 2018

By Joshua Micah Hoffman, Jhon Silva-Castro, Kylie Larson-Robl

A coal mine impoundment failure has the potential to be environmentally devastating and life-threatening. It is well documented that after seismic events slope failures in impoundments can occur. It has been concluded that often the main driven factor of the failure is the increase in excess pore pressure due to ground vibration. A small amount of research has been done regarding the stability of coal mine impoundments under natural seismic events; however no research has been done considering vibrations from mine blasts. If it is taken into account that current environmental restrictions oblige to increase the capacity of coal mine impoundments, thus increasing the hazard of such structures, it is necessary to evaluate the effects of near-by mine blasting on the stability of the coal mine impoundments in order to mitigate and control the potential of slope failures. To study the behavior of excess pore pressure under blasting conditions, scaled simulations of production blasting events were set up inside of a controlled sand tank. The research was divided in two stages. The first one was done, using dry conditions, while in the second part, the same set of tests were performed under saturated conditions. This document shows the partial results for stage one (dry conditions). For the tests, explosive charges were set off within the sand tank at various distances to simulate different blasting distances. Information was collected from geophones, accelerometers, microphones and high speed video camera for dry and saturated scenarios and additionally from piezometers under saturated conditions to assess the behavior of the material under blasting conditions.

Jan 1, 2015

By G. Cordingley, A. Mwanza

Lumwana is an open pit Copper mine located in the Northwestern Province of Zambia approximately 80 km west from the provincial capital of Solwezi, approximately 300 km northwest from the Copperbelt and 700 km northwest from the national capital of Lusaka. The mine has two major Copper deposits: Malundwe and Chimiwungo. Copper mineralization includes Chalcopyrite, Bornite and Chalcocite. In addition to Copper, these deposits also contain the undesirable element Uranium contained in vein hosted and disseminated Uranite. The processing plant was designed using conventional technologies: semi-autogenous grinding (SAG) and ball mill for grinding, and mechanical cells for rougher and cleaner flotation. Soon after commissioning in early 2009, it was recognised that two stages of conventional cleaning were unable to produce plant final Copper concentrates with the desired Uranium grades. Studies have shown that a significant quantity of liberated and fine Uranium particles (up to 80-90%) is recovered with the concentrate by entrainment. Lumwana Operations sought the use of the Jameson Cell technology after observing successful implementation at other sites in rectifying similar issues. In late 2009, Jameson Cell pilot-plant test work was conducted at the site and this quickly led to the installation of a full-scale B5400/18 model into the existing cleaner circuit. Inclusion of the Jameson Cell resulted in the plant being able to effectively produce clean and saleable concentrate with Uranium contents consistently below acceptable levels. Initially designed to be used as a cleaner scalper cell at the head of the existing conventional cell circuit, subsequent operational issues with the existing recleaner cells forced reconfiguration of the cleaner circuit and reintroduced the Jameson Cell for the recleaning duty. This paper reports the Lumwana Operation from the first two years of operation where it struggled to produce a saleable concentrate with Uranium grades below 150 ppm, which is the maximum allowable limit set out in the smelting contracts, to steps taken in the subsequent years to implement a satisfactory solution. The plant can now consistently produce a clean Copper concentrate with Uranium grades well below 130 ppm and the overall improvements implemented at site have seen the overall plant recovery improve by 1.3%.

Jan 1, 2014

By Braja M. Das

Laboratory model test results for the ultimate uplift capacity of square and circular foundations in saturated clay (ø=0) have been presented. The results of the present model tests for square foundations have been compared with the previously published laboratory model tests results on circular foundations. Based on the comparison, it appears that the critical embedment ratio of square and circular foundations increases from about 3 for soft clays to about 7 for medium to stiff clays. By using the experimental results, an empirical procedure has been suggested for determination of the ultimate uplift capacity of belled pier foundations in saturated clay.

Jan 1, 1987

By L. D. Smith

"This paper examines the impact of the various assumptions that go into an economic evaluation, and shows how these can be combined to show an exciting result that may not really exist. An example of an embellished case (the kind that one frequently sees when projects are being promoted) is developed and the cumulative impact is analyzed to show the actual project underneath. The paper also points out some areas to watch for overly optimistic assumptions such as prices, inflation, and debt. The concept of a “bare bones” base case is proposed (constant metal prices, constant dollars, no inflation, no debt, no interest, on a project basis, after tax) as a common reference point.As well, the discount rate is examined as one of the fundamental means of reflecting risk in discounted cash flow evaluations. Current industry practice is discussed, and a methodology for the analysis of risk levels is proposed that assesses the constituent components of the discount rate: real interest, mineral project risks, and country risk."

Jan 1, 2002

By Derek H. C. Wilton

"The Nain Province (NP) of northern Labrador is a >600 km long by =100 km wide Archean craton that has undergone relatively little mineral exploration until economically signifcant concentrations of orthomagmatic nickel sulphide were discovered by Diamond Fields Resources (DFR) at Voisey’s Bay. Due to the great time span between crust formation andfnal intrusive activity (ca. 3.9 Ga to 1.27 Ga),there were, however, numerous metallogenic events within the NP.The NP was intruded by the ca. 1.3 Ga to1.2 Ga Nain Plutonic Suite (NPS) composite anorthosite-granite complex. The NPS dividesthe NP into the southern Hopedale Block (90 km by 150 km) and the northern SaglekBlock (375 km long by =50 km wide). These two blocks appear to represent two distinct Archean cratonic nuclei, each with its own distinct metallogenic history. The NPS is a coalesced assemblage of composite intrusions which include anorthosite, troctolite, norite, gabbro and granite.The Hopedale Block contains the Hunt River and Florence Lake greenstone belts, and the Weekes Amphibolite which represents remnantsf the older Hunt River greenstone belt. Geologically, these belts have some potential to host komatiitic Kambalda-style nickel, volcanogenic massive sulphide (VMS) and meso -thermal lode gold mineralization. The unconformity between Paleoproterozoic cover sequences and the trondhjemite-tonalite-granodiorite (TTG)suite which engulfed the greenstones was the locus for lead-zinc-bearing quartz-carbonate veins. Minor fracture-hosted uraninite showings are also present in the TTG.The Saglek Block is a high-grade gneissterrane with deformed Archean supracrustal sequences but no greenstone belts. Within the gneiss are variably-sized enclaves that range in composition from anorthositic to ultramafic; some of these latter xenoliths contain abun-dant fuchsite. There are also three small anorthositic to ultramafic meta-igneous complexes present in the gneiss near Okak Bay.Some Archean meta sedimentary and maficgneiss supracrustal sequences contain iron-oxide and sulphide members. The sulphide-bearing Tasiuyak parag neiss defines the cra-tonic suture between the NP and Churchill(Rae) Province. Along the cratonic suture between the NP and Churchill Province from Ramah Bay north are remnants of the Archean(or Paleoproterozoic) Hutton Anortho site Suite. Ultramafc layers within the suite contain chromite and elevated Ni values.Three ca. 2.0 Ga supracrustal sequenceswere deposited in small fault-bounded basins within the NP. The Snyder Group contains pyrrhotitiferous massive sulphide horizons. TheMugford Group contains SEDEX-like massive sulphide blocks in a debris fow and ultramafic sills with unusual PGE concentrations; alaskitic granite cutting basement gneiss to the group contains stockwork-like pyritiferous quartz veins. The Ramah Group contains numerous MVT-style zinc-lead sulphide occurrences.The Reid Brook Intrusion of the NPS contains enormous and high-grade nickel-copper-cobalt massive sulphide bodies at the Voisey’s Bay deposit. Exploration in the northern portions of the NPS in 1995 has indicated the presence of other potentially economic nickel sulphide horizons."

Jan 1, 1996

Gullies are the vital in-stope excavations that provide access for mining personnel and material to, and mined ore from, the producing faces in the tabular hard rock mines. They pose a serious problem in most mines because they induce stress orientations, which, combined with blast damage, produce adverse rock fracture patterns that contribute to the loss of hangingwall and sidewall integrity. Rock-related injury statistics confirm this by highlighting gullies as the second-highest risk area in South African hard rock mines. Inappropriate gully geometries, poor blasting practice, and non-adherence to accepted standards worsen the problem. The aim of this work is, firstly, to provide guidelines to select the correct gully geometry and appropriate support for a particular geotechnical environment and, secondly, to review the practical issues behind gully safety and stability. In order to meet these aims, this paper reviews the available literature on gullies and their history, and reports on an industry-wide survey of practices and opinions. Then it covers observations from underground visits to 107 gullies situated in the respective geotechnical environments of the Basal Reef, Beatrix Reef, Vaal Reef, Carbon Leader Reef, Ventersdorp Contact Reef, Kimberley Reef, Kalkoenkrans Reef, Merensky Reef, and UG2 Reef. Despite the differing geotechnical conditions and gully geometries, common problems are experienced with geological structure, stress, and fracturing. Results from numerical modelling are also presented to help analyse the underground observations and to quantify the merits of the different gully layouts. It is concluded that there are no new techniques available to improve gully stability, but that significant improvements in safety are attainable by employing the correct gully geometry for the geotechnical environment, good blasting practice, and appropriate support.

Jan 1, 2002

By Ryan C. Stephan, Christopher Mark

"Some of the weakest roof in United States coal mines is found in the Illinois Basin. Historically, the Illinois Basin has also suffered from high rates of unplanned roof falls and rock fall injuries. During the past decade, however, roof fall and rock fall injury rates have fallen dramatically, and are now lower than the national average. Several technologies are responsible for the improvement. Roof screen was rarely used ten years ago, but a number of mines now use it on a regular basis to prevent rock falls and rock fall injuries. Other roof skin control fixtures and work practices have contributed as well.The reduction in roof falls is also directly attributed to enhanced intrinsic roof support. Stiffer primary bolting patterns have reduced the magnitude of roof spalling and roof sag. They have also helped create a more intact beam that is able to be suspended from longer cable bolts. Cable bolt design methodology has also contributed to this reduction in roof falls. Some early cable bolt applications were unsuccessful because they employed as few as two cable bolts per intersection. This paper describes a methodology for estimating rock loads for support design.ROOF FALL TRENDS IN THE ILLINOIS BASINAlthough the Illinois Basin has a long history of poor roof conditions and high rates of unplanned roof falls and rock fall injuries, recent data indicates a change in the trend. Roof fall rates are determined by dividing the total number of non-injury roof falls by the total number of hours worked underground. The data is considered for 200,000-man hours. While the Illinois Basin was once a coalfield experiencing roof falls at nearly twice the national average, it is now at or below the national rate. Figure 1 indicates the trend over the past 20 years. In 2008, the Illinois Basin mines experienced 5.06 roof falls every 200,000-man-hours, compared to only 0.75 in 2018.There has also been a significant reduction in the rate of rock fall injuries in the Illinois Basin coal mines, as shown in Figure 2. In 2008 there were 1.48 rock fall injuries every 200,000-man-hours, compared to only 0.43 in 2018.ILLINOIS BASIN COAL ROOF GEOLOGYThe roof rock in the Illinois Basin has been studied in the past to understand the primary causes of roof failures (Molinda et al., 2008; Thompson, 2010; Molinda and Mark, 2010). Rusnak and Mark (2000) evaluated 10,000 laboratory strength tests from 800 rock units and concluded that for shale, siltstone, and sandstone, the strength of the Illinois Basin variety was less than half that of the same rock types in Central Appalachia (Figure 3). A study of Coal Mine Roof Rating (CMRR) measurements in more than 200 US coal mines also found that weak roof was predominant in the Illinois Basin (Mark and Molinda, 2005)."

Jan 1, 2019

By Yuting Xue, Danqing Gao, Brijes Mishra

Heterogeneity and discontinuity significantly affect rock strength. For accurate stability prediction, intact rock behavior is imperatively included in rock mass behavior. However, past research largely used arbitrary scaling approaches to produce rock strength. This paper considers a stochastic approach in order to determine the strength of a rock. Based on the laboratory data, a MATLAB® with extreme value stochastic model generates a database for each physico-mechanical property. Then FLAC® simulates laboratory-sized rock specimens. The grids developed in the numerical model can in turn develop random material properties in MATLAB®, which researchers then applied to the final FLAC® model. Model runs simulate the approach performed in the laboratory. The results from the model indicate that a stochastic approach produces strengths that are lower than a deterministic approach. Failure modes for each specimen are different, similar to observations in the laboratory. In addition, random density also influences the failure mode, highlighting the importance of stochastic analysis in rocks.

By Yuting Xue, Danqing Gao, Brijes Mishra

Heterogeneity and discontinuity significantly affect rock strength. For accurate stability prediction, intact rock behavior is imperatively included in rock mass behavior. However, past research largely used arbitrary scaling approaches to produce rock strength. This paper considers a stochastic approach in order to determine the strength of a rock. Based on the laboratory data, a MATLAB® with extreme value stochastic model generates a database for each physico-mechanical property. Then FLAC® simulates laboratory-sized rock specimens. The grids developed in the numerical model can in turn develop random material properties in MATLAB®, which researchers then applied to the final FLAC® model. Model runs simulate the approach performed in the laboratory. The results from the model indicate that a stochastic approach produces strengths that are lower than a deterministic approach. Failure modes for each specimen are different, similar to observations in the laboratory. In addition, random density also influences the failure mode, highlighting the importance of stochastic analysis in rocks.

By J. Kretschmann

Mining heritage can be of outstanding value for many regions around the world, because mining has been done for thousands of years for the benefit of mankind and its development. This paper presents an ongoing project creating a general guideline for the handling of mining heritage on the basis of experiences made in Germany. Interactions of stakeholders in the ?heritage network? as well as strategies for the technical proceeding will be described. An action plan for the sustainable handling of mining heritage has already been developed in part, which includes necessary measures. Best-practice recommendations will be derived. Keywords: m ining heritage / preservation / guidelines / action plan / Sustainability

Feb 27, 2013

By H. Meseck

The new building of the Central Bank of Iraq in Baghdad was footed in difficult underground conditions on more than 600 reinforced concrete driven piles, with cross-sectional diameters of 45 x 45 cm and pile lengths of 12.0 to 18.0 m. The necessary embedded depth and the bearing capacity thus reached were established on all 600 drives piles by means of dynamic pile tests. For the calibration of the dynamic pile tests, 6 static pile load tests were carried out. The execution of the construction and the results of the extensive tests on the building site are shown.

Jan 1, 1989

By Rainer Kahrger

This paper is a follow-up to the paper presented at the SME meeting in April of 1996. Since then, the El Abra facility has been started up, 9 months ahead of schedule, and has processed about 45 million tons of ore and produced over 700 million pounds of copper. For those unfamiliar with the El Abra materials handling and leaching facilities, a brief overview of the facility is provided. The paper will then deal in detail with such aspects of Conveyor 103, the long regenerative overland conveyor, including: actual running resistance starting and stopping procedures emergency brake test at 10,000 t/h Additionally, we shall take the opportunity to report on a catastrophic culvert collapse in October 1996, which stopped the conveyor abruptly at full speed and under high load condition, causing a belt breakage. We would like to use this opportunity to thank the management of El Abra and Cyprus Amax for providing assistance and allowing us to present this paper. The El Abra team deserves a great compliment for building this one billion dollar facility in record time in a remote area of a high-altitude desert with no existing infrastructure, and for bringing it so quickly up to full operating capacity. The El Abra management had to assemble a completely new operator team. Considering the above circumstances, it took a great effort by all involved to achieve success. The official performance test which was required by the lending banks was successfully concluded in November 1997.

Jan 1, 1998

By James P. Stewart

This case history describes the engineering design and construction for the Contractor of a 35-ft-deep excavation for an 800-square-foot addition to an existing sewage pump station. The site posed unexpected geotechnical complications that included deep gravelly soil, a history of local construction difficulties, groundwater consisting of heavy salt brine, and the need to underpin the existing pump station. The project took an interesting twist when the Owner issued a change order limiting the dewatering discharge to a fraction of that required to lower the water table. This documents the interesting circumstances of this job and documents the unusual subsurface conditions in the Syracuse, NY Lakefront area.

Jan 1, 2003

By Timothy J. Orr, Robin J. Burgess-Limerick, Jennica L. Bellanca, MARGARET E. RYAN

Powered haulage continues to be a large safety concern for the mining industry, accounting for approximately 50%of the mining fatal accidents every year. Among these fatal accidents, haul-truck-related accidents are the most common, with 6 of 28 and 6 of 27 fatal accidents occurring in 2017 and 2018, respectively. To better understand why these accidents continue to occur and what can be done to prevent them, researchers reviewed the 91 haul-truck-related fatal accidents that occurred in the USA from 2005 to 2018 and performed bow-tie analyses using the final reports published by the Mine Safety and Health Administration. The analyses explore the context of the accidents with a focus on the initiating event, event outcome, hazards present, and possible preventative and mitigative controls. Overall, the vast majority of the accidents resulted in a haul truck colliding with the environment, and the majority of these events were initiated by loss of situational awareness or loss of control. The majority of the hazards were related to design and organizational controls. The results of this study suggest a need to investigate operator decision-making and organizational controls and to focus on improving design and operation controls such as mine design and operational procedures.

Feb 22, 2021

By W. L. Dare

This publication is one of a series prepared by the Federal Bureau of Mines on methods and costs of producing uranium ore on the Colorado Plateau. The information it contains was gathered in 1955-58 and applies to eight small operations. (See fig. 1.) Mining costs have increased since the data were I collected, but the information should be helpful in estimating future costs I at similar deposits. The Bureau of Mines had early experience in the production of carnotite-type ores on the Colorado Plateau.3 4/ Under a cooperative agreement with the National Radium Institute in 1914-16, the Bureau mined and concentrated carnotite ore for recovery of radium, uranium, and vanadium. The ore was taken from claims in or near Long Park Montrose County, Colo., about 3 mi. south of La Salle Mining Co.'s La Salle mine, which is one of the mines described in this report. The Bureau leased the claims from Crucible Steel Mining & Milling Co., a subsidiary of Crucible Steel Co. of America, and from 1914 to 1916 produced 990 tons of high-grade ore, containing 2.6 pct. U308, and about 2,000 tons of mill-grade ore, containing 0.85 pct. U308. The high-grade ore was shipped directly to a radium-recovery plant built in Denver in 1914 under the cooperative agreement. There, commercial methods of extracting uranium, vanadium, and radium from carnotite ores were developed by Bureau personnel. The lower grade ore was concentrated at a small mill in Long Park before being shipped to Denver. The final recovery was 69,000 lb. of U308 and 8.8 g. of radium. The direct mining cost of producing the high-grade ore, including the labor to hand sort and sack it, was $35.96 per ton. Freighting the ore 58 miles to Placerville, Colo., the nearest rail point on the Rio Grande Southern Railway, cost $25.28 per ton, which included $4.55 per ton for ore bags and twine. Four-or six-horse teams pulled two wagons in tandem and made the

Jan 1, 1961

By F. X. Prins, L. R. Nelson

Tight control of electrode paste additions, hard and soft paste levels, baked zone position and electrode temperatures are integral to superior Söderberg electrode management practices. Paste addition is typically effected through briquettes, cylinders or large blocks. Each electrode paste form has its advantages and disadvantages, but probably a more crucial element from an electrode control perspective is the frequency and amount of electrode paste addition into a Söderberg electrode column. The detrimental effects of excessive soft paste levels leading to Stokes? Law segregation of paste in the electrode column are well documented, while several operators have effectively implemented the use of electrode thermocouples to monitor paste temperatures and automated slipping algorithms to control baking conditions within electrodes. Somewhat less well appreciated are the negative influences of inadequate soft paste levels, especially when coupled with excessive paste cylinder or block additions and resulting high hard paste levels. The alternative of insufficient hard paste levels and associated overheated electrode paste must also be considered, and can contribute to paste segregation directly. This condition also has the potential to generate gas mixtures in the electrode column that are concurrently a potential health hazard, while being prone to spontaneous combustion. Results of industrial trials on electric furnaces using Söderberg electrodes in a variety of applications from ferrochromium, to ferromanganese and even platinum-bearing base metal sulphides smelting are presented to illustrate the influence of paste loading practices on the dynamics of hard and soft paste levels. Possible electrode failure mechanisms attributable to inadequate paste level control will be discussed through some industrial examples. Suitable paste loading practices to mitigate the risks of inappropriate paste levels and associated electrode incidents are presented.

Jan 1, 2004

By Donald Leroux, Asim Tuzun, Simon Gariépy, Luc Lachance, Hayley Halsall-Whitney

"The importance of coherent material balance results has long been recognized by mining and metallurgical companies. Although this is still true nowadays, various stakeholders are increasingly concerned about the origin and the accuracy of the reported numbers. The last decade has shown that most metallurgical accounting concerns can be addressed by making two important changes to plant performance monitoring practices. First, introducing data redundancy into the metal balance procedure allows the estimation of measurement errors. Second, the migration from spreadsheet-based to relational database based systems brings transparency, data integrity, traceability and auditability into metallurgical accounting. Relational databases also facilitate the production of reports that metallurgical accountants must issue routinely. Recognizing the caveats of the spreadsheet-based metal accounting method they had been applying for years, Strathcona decided to switch to a commercial relational database system in 2008. For the most part, the migration was seamless. Some challenges were raised but they could all be overcome and outweighed by benefits gained from day-to-day utilization of the system.INTRODUCTION Metal accounting (Morrison, 2008) has always been essential to high-quality corporate governance of mining and metallurgical companies. Although the importance of coherent material balance results has long been recognized, various stakeholders are increasingly inquisitive about how the reported numbers were obtained and how much accuracy can be attributed to them. This accrued scrutiny is obviously no stranger to the corporate governance tightening that happened through the years in response to outrageous accounting scandals. It is also in continuity with securities laws (such as NI-43-101 in Canada) that were passed to protect the public from other market fraud. Recognizing the importance of spotless metal accounting in their reports to the public, a group of global mining companies gave AMIRA International the mandate of developing a set of rigorous yet practical metal accounting guidelines for the mining and metallurgical industry. The AMIRA P754 project was launched in 2004 and the first version of the resulting Code of Practice was released the following year. Since then, the Code was reviewed twice and revised releases were issued (AMIRA, 2007). While some parts of these guidelines are in continuity with current commonplace practices, other parts recommend changes to inherited practices that may be significant. For example, they highlight the importance of data redundancy (Lachance & Flament, 2011) which in many operations is either already available but unexploited or achievable with reasonable efforts. These guidelines also stress the importance of state-of-the-art metal accounting systems, such as those based on relational databases, which are secure and entirely auditable by a Qualified Person. Because most spreadsheet software packages allow data and formulae to be modified at any time, without a trace and anonymously, they do not meet these requirements."

Jan 1, 2012