Search Documents

By G. van den Berg

Anglo Platinum has initiated a project to investigate hydraulic hoisting technology for platinum mines. Hydraulic hoisting systems are categorized as pumping, fluidizing feeder or displacement feeder systems. Positive displacement piston diaphragm pumps are most suitable for pumping systems but they require that the ore be milled prior to pumping. Fluidizing feeders are unsuitable for platinum ore applications due to the large percentage of fines in the ore. The three-chamber pipe displacement feeder has been most widely used for hydraulic hoisting and is the most suitable technology for platinum mines. Eight hydraulic hoisting applications covering pumping and displacement feeder technologies are reviewed. The key factors to be assessed in selecting a hydraulic hoisting system for a platinum mine are discussed. A typical platinum mine configuration will comprise an ore preparation plant (to produce -15 mm material through screening or crushing), motive water pump on surface, high pressure water pipeline from surface to underground, ore slurrification plant, three-chamber displacement feeder, and a high pressure slurry pipeline to surface. The water and slurry pipelines are housed in a purpose drilled borehole. A hydraulic hoisting system selection chart is presented. A 150 mm diameter system with a 25 MPa pressure rating is required to hoist 60 000 t/m from a depth of 1 200 m. Generic capital and operating costs are presented . A major potential advantage of hydraulic hoisting is that the fines, which contain a high percentage of PGMs, are captured underground and transported directly to the concentrator. Hydraulic hoisting technology is ideally suited to providing supplementary hoisting capacity to existing shafts that have reached the skip hoisting capacity limit. The main advantage for new shafts is the potential to significantly simplify underground rock handling and transportation. All hydraulic hoisting system components are proven. The only risk area is the wear rates of the valves and piping. Current estimates are based on gold ore. The business cases investigated show that the financial viability of the installations are not sensitive to wear rate. Hydraulic hoisting is technically feasible and financially attractive for platinum mines. Keywords: Hydraulic hoisting, slurry

Jan 1, 2004

By R. A. McIvor, R. Levac

"The Stobie No. 7 shaft, 14 ft diameter, double- drum skip hoist, was installed at the INCO Limited Frood Stobie Complex in 1942. Figure 1 shows the hoist layout. The hoist was originally equipped with babbitted journal bearings on the main drum shaft and pinion gears. In 1990, the hoist was modernized with a new braking system, two new 2000 hp D.C. drive motors, a thyristor armature supply and a PLC control system. The new drive motors were connected to the drive pinion gears with a gear type flexible coupling. The pinion gear journal bearings were refitted during the refit in 1990 as the existing babbitted bearings showed signs of wear. The pinion gear journal bearings had always run warm and had external cooling applied during the warm summer months. Figure 2 shows the journal bearings on the pinion shaft. The skip hoist main bull gear and two pinion gears were replaced in 1997 because of cracked bull gear spokes. New drive couplings were installed on the pinion gears and the pinion journal bearings were modified to allow some self-aligning properties to try to reduce the heating and wear on the babbitt. The modifications did not significantly reduce the heating problems and a decision was made in the spring of 1998 to convert the bearings to self-aligning, anti-friction-type bearings.The traditional roller bearings used on double helical pinion drive gears in hoist applications has always been double-row spherical roller bearings due to their high load-carrying capacity and misalignment allowances.Unlike single helical gears, double helical arrangements do not exert axial thrust on the pinion gear bearings, therefore, both bearings in the pillow blocks must float easily with any pinion displacement. Drum misalignment, thrust bearing end play and a multitude of other influences causes continuous axial displacement of the pinions when in operation. This constant displacement or “hunting” of the pinion gear to maintain its centre on bull gear often exceeds the axial clearance limits of spherical roller bearings thus resulting in a continuous sliding motion of the bearing outer rings against the housing seats. With time, the housing fit eventually wears, creating an out-of-round condition for bearing housing (maximum allowable cylindricity tolerance is IT4/2). When this happens, the pillow block housings must be replaced or re-machined to specification. Premature bearing wear and overheating will occur if a housing out-of-round condition is encountered."

Jan 1, 2001

1. Domestic Production and Use: In 1977, 12 companies operated 31 primary aluminum reduction plants, with 3 firms accounting for 65% of production capacity. Washington, Oregon, and Montana accounted for 31% of the total capacity; Gulf Coast States 23%, Northern States 26%, and other Southern States 20%. Based on estimated producer prices output of primary metal in 1977 Has valued at $4.6 billion. Aluminum consumption by 25,000 firms was centered 'in the East Central United States. Of aluminum consuming industries in 1977, building accounted for about 25%; packaging 22%; transportation 21%; electrical 11%; consumer durables 9%; and other uses, 12%.

Jan 1, 1978

By J. A. Scott, K. Moreau, H. Shang

"Trials of automated technology at underground mine sites around the world have reported increased production and the potential for lower energy consumption. Autonomous mining eliminates a range of delays related to operator downtime and travel to the workface and facilitates continuous operation in conditions that are unsafe for workers. Automation also introduces complexities and safety hazards arising from equipment–personnel interactions; automated processes must be isolated from other stope-cycle–related activities such as production drilling, development, loading, and backfilling, poten¬tially requiring changes to the mine design to maintain an efficient and safe operation. This paper reviews and discusses the implementation of automated equipment in deep underground mining operations and the challenges and advantages associated with the technology. ¦ KEYWORDS Automated equipment, Emissions reduction, Energy, Productivity, Sustainability, Technology, Underground mines RÉSUMÉ Des essais de technologies automatisées dans des sites miniers souterrains aux quatre coins du monde ont indiqué une production accrue et la possibilité de réduire la consommation d’énergie. L’exploitation minière autonome élimine tout un éventail de retards liés aux temps d’immobilisation des opérateurs et aux déplacements vers le front de taille, et facilite l’exploitation continue dans des conditions qui s’avèrent peu sécurisées pour les travailleurs. L’automatisation introduit également des complexités et des risques pour la sécurité, qui surviennent en raison des interactions entre l’équipement et le personnel. On recommande d’isoler les procédés automatisés des autres activités liées au cycle des chantiers telles que le forage de production, le développement, le chargement et le remblai, ce qui pourrait entraîner des changements au niveau de la conception de la mine afin de préserver rendement et sécurité dans l’exploitation. Cet article examine et aborde la mise en oeuvre de l’équipement automatisé dans des exploitations minières souterraines profondes, ainsi que les enjeux et les avantages associés à cette technologie. ¦ MOTS CLÉS durabilité, énergie, équipement automatisé, mines souterraines, productivité, réduction des émissions, technologieINTRODUCTION As the mining industry continues to exhaust easily accessible orebodies, the need for efficient, deep (typically below 2,500 m) mine operations increases (Atlas Copco, 2013a); however, the mining process can become economically infeasible at great depths because operation costs drastically increase. This has resulted in investigations into automating mining operations as the industry strives for improved productivity (Schunnesson, Gustafson, & Kumar, 2009) and ways to remove personnel from hazardous work areas."

Jan 1, 2019

By J. Venter

The history of firedamp is the same as that of coal: The initial stage was the accumulation of vegetation, which was converted into peat under certain local conditions, then lignite, bituminous coal, and finally anthracite. These deposits ceased to increase owing to inundation that deposited earthy sediment, sometimes as much as several tens of meters (several tens of yards). The vegetable matter, whether it was covered with sediment or not, began to ferment. The basic organic components of the vegetable matter are: Cellulose, lignin, and wax and resin in varying proportions, according to the different kinds of vegetable matter. There are, in addition, some impurities, generally mineral.

Jan 1, 1953

Real economic growth for the year will most likely exceed the Administration's estimate of 3.2%, up from 2.9% in 1986, unless consumers change their spending patterns more than expected as a result of the October stock market decline. The economy grew at a real annual rate of 3.7% in the first three quarters of the year, Analysts agree that the stock market decline will slow economic growth-- most have lowered their growth expectations for 1988 by about 1%; but few would argue that the economy will slow significantly in the fourth quarter of 1987. [ ] During this economic recovery, personal consumption expenditures provided the main impetus for growth and a deeping trade deficit, the main hindrance to growth. In 1987, however, personal consumption expenditures grew at a lower rate than the overall economy. Mush of the economic growth resulted from a reduced trade deficit and growing investment by business in equipment to improve productivity and to meet the domestic and foreign demand for products. The declining value of the dollar resulted in a better competitive position for U.S. goods but also contributed to a rising rate of inflation as imports rose in price. Inflation, as measured by the fixed-weighted index for gross national product, was still far below the rates in the early 1980k, however. More than 2 million jobs were created during the year, predominantly in the service sectors of the economy, and the monthly unemployment rate in September fell to the lowest level in a decade. Then, after 13 months of decline, the unemployment rate edged up 0.1 percentage point to 5.9% in October.

Jan 1, 1987

By O. C. Garst

"The lightness and relatively high strength per unit weight of certain magnesium alloys have interested designing engineers for many years. Ever since the noted investigator Bunsen3/ first produced the element by electrolysis of the fused chloride in 1852, utilization of this light metal has been considered. Magnesium is widely distributed over the earth's surface in high-grade as well as low-grade deposits; it occupies eighth place in the list of elements arranged in order of their decreasing abundance, as there is 2.24 percent magnesium in the earth's lithosphere. Even though the element is distributed widely in the form of relatively insoluble: minerals and also as soluble salts in sea water and spring water, as well as being an indispensable constituent of plants and animals, the technology of magnesium was slow development. This slowness of development was first caused by confusion or the part of the early investigators who thought that magnesia, magnesite, magnetite, and the pyrolusite-type manganese ores were compounds of the same metal. At one time the metal that we now know as manganese was called magnesium, and magnesium was called either magnium or talcium. In addition to this coon, the chemical activity of the metal, especially at high temperatures, created problems that are still difficult to solve.With the advance of science in all branches, .methods for -he production of magnesium were developed. The methods first used for producing the element were: (1) reduction of magnesium salts with alkali metals,4/ (2) electrolysis of aqueous solutions of magnesium salts, and (3) electrolysis of fused magnesiun salts.The first attempts to produce magnesium by the carbothermal reduction of magnesia were failures as sufficient thermodynamic knowledge concerning the reversibility of the reaction between magnesia and carbon was not at hand. As the igneous electrolytic Method for making the element was more easily controlled than the others and. yielded more metal per unit of energy, considerable work was expended on the improvement of this process. The work in this field paralled that on the electroreduction of aluminum and the alkali metals. For several years the entire magnesium industry was dependent on this igneous electrolysis process for its supply of the metal, but as demand for the metal increased and more scientific knowledge was available, other processes were developed. Today magnesium is produced by the electrolysis of molton magnesium chloride electrolytes, the carbothermal reduction of magnesia, in arc furnaces followed by shock cooling of the furnace gases by a coin inert atmosphere, and the silicothermal reduction of calcined dolomite in stainless steel retorts."

Mar 1, 1946

By Branch of Editorial Services

"The Bureau of Mines was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment, and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve material resources and prevent their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting those industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau of Mines to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non-Bureau publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented in this special publication both necessary and valuable. This issue of the Bureau of Mines List of Publications and Articles describes reports and articles published during the period January 1, 1980, to December 31, 1984. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960;1 the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960;2 the 5-year lists of publications and articles from January 1, 1960, to December 31, 1964,3 from January 1, 1965, to December 31, 1969,4 from January 1, 1970, to December 31, 1974,5 and from January 1, 1975, to December 31, 1979;6 and the annual lists of Bureau publications and articles from January 1 to December 31, 1980,7 from January 1 to December 31, 1981,8 from January 1 to December 31, 1982,9 and from January 1 to December 31, 1983. 10"

Jan 1, 1985

The placer gold industry has experienced a roller-coaster history incorporating four major boom eras. The first, 'hand-methods' boom arose in the mid-19th Century from application of an old idea in new places around the globe. The subsequent hydraulic mining, bucket dredging, and 'hydraulic excavator-portable plant' booms each arose from application of new ideas in old places around the globe, ie in places where gold had been found during earlier booms. The new ideas that heralded the second, third and fourth booms were all significant advances in excavation technology. These enabled the industry to target the known deposits that were too deep, too wet, too small, or too low-grade for recovery by earlier boom methods. Relatively few new deposits or new deposit styles arose from the 'history book' exploration approach, so the number of known deposits to which each of the boom methods were applicable was limited. Consequently, the first three booms were each followed by significant periods of industry decline, and the fourth boom is currently waning inNew Zealand. Further decline is not inevitable and can be avoided by changing to a knowledge-based exploration approach similar to that adopted by the hard rock gold industry in the 1970s. Such an approach could easily herald the next placer gold boom.   Most of the relatively coarse, easily won alluvial gold in proximal and medial reaches of the active placer systems is gone. However, a substantial alluvial gold resource remains in the distal reaches of active systems, and in ancient placers formed onshore and on the continental shelf during previous sedimentary cycles. The resource in these deposits probably exceeds the total New Zealand placer production to date. Successful development of these placers requires application of robust geologic models for the formation and distribution of the placers through time, and advanced exploration technology that has not been used before in New Zealand. Nevertheless, the knowledge and technology required to explore and mine these deposits is available now. Many of these deposits contain a large proportion of problematic gold types that are difficult to recover with the commonly used gravity technology without sustaining significant losses. Despite advances in recovery technology in last few years, too much emphasis is placed on the incorrect assumption that gold size is the primary control on recovery efficiency. Other gold particle parameters, especially particle shape, exert a much greater control on whether gold will be saved or lost to the tails, and must be considered in the design of recovery technology and configuration of recovery circuits.

Jan 1, 2003

By Arno C. Fieldner

This is the fifth of a series of annual reports4/ of technologic investigations conducted by the Bureau of Mines on the occurrence, properties, mining, preparation, and uses of coal. The research of the Bureau is carefully coordinated with the requirements of the producing and consuming industries, with a view to conservation of resources of coal in mining and use, and conservation of the health and lives of workmen employed in these industries. Such coordination is facilitated by the wide range of specialization of the several groups on engaged in studies concerning coal. Here are reported correlated studies ranging from paleobotanic analysis of the formation of coal as it occurred some millions of years ago to the effect of mechanical methods of mining on present-day employment in mines. As this is a summary of the current work of the Bureau of Mines, so the Bureau likewise has provided a condensed review of the outstanding current work of others on research and technology of coal 5/.

Jan 1, 1940

By Shigeo Asai

"Electromagnetic processing of materials is newly proposed to be considered as one of the engineering fields where functions of electromagnetism are utilized for processing electrically conducting materials, such as liquid metals, electrolytes and plasmas. The background requiring this processing and the engineering characteristics supporting it are described. The applicable functions of electromagnetism to material processing are revealed from the view point of magnetohydrodynamics. The existing processes and the proposed ones are classified into utilized functions and engineering applications are discussed. IntroductionElectric energy has been used in the metallurgical field for the processes of melting, refining and solidification. In these cases both the magnetic field which is induced by an imposed electric current, and the electric current are applied on electrically conducting materials such as molten metals. Thus, it turns out that the magnetohydrodynamic (MHD) phenomena have unconsciously been seen in metallurgical processes using electric current. The academic backbone studying MHD phenomena is the Magnetohydrodynamics which is being developed in the fields of plasma physics, astrophysics, fusion research and nuclear energy.The first attempt where magnetohydrodynamics was intentionally applied on metallurgy was a Symposium of IUTAM (The International Union of Theoretical and Applied Mechanics) in titled as ""Metallurgical Applications of Magnetohydrodynamics"" at Cambridge, UK, 1982 [1]. This timely event stimulated a few metallurgists to recognize the importance of ~MHD and was a good warning to the metal societies in the world. Especially in Japan, the Steelmaking Investigative Subcommittee of Research Planning Committee in the ISIJ (The Iron and Steel Institute of Japan) discussed the application of ~IHD to metallurgy and selected it as one of the four major innovative subjects for future steelmaking technology in Japan [2]. Indeed, the term of ""Electromagnetic Metallurgy"" itself was firstly coined by this subcommittee. Upon the request of a report from the subcommittee, the ISIJ has established a committee on ""Electromagnetic Metallurgy"" at 1985, under the author's chairmanship."

Jan 1, 1988

By Meyer Klein

Decision theory is the formal theory of the logic of decisions in view of the decision maker's objectives, preferences, I beliefs, and available information, It usually deals with weighty economic problems involving irrevocable (or costly to reverse) decisions. Capital investment planning problems constitute an instance par excellence for application of the decision theory concepts. Decision theory as it is presently conceived has evolved in recent years. At first it concentrated on decisions in the face of total lack of information and on games with intelligent adversaries. The results of these efforts proved theoretically interesting, but practically of little applicability. In the last few years, stress has shifted to the introduction of subjective probabilities and preferences, and the results have been eminently successful in applications both in government and with- in business firms in the resolution of complex problems.

Jan 1, 1970

By A. N. Baldwin

This report documents work performed under Bureau of Mines Contract J0265029 to study and develop two innovative mining systems: ? An underground auger capable of augering into the right and left ribs without repositioning the machine ? A conventional mining system employing recently developed innovative machinery. The report is separated into two volumes to document the two studies separately. Volume I describes work performed and the recommended concept for a bidirectional auger. Volume II describes the studies of mining equipment performance and mining plane developed to determine a conventional mining plan offering improved productivity.

Jan 1, 1977

By E. L. Oliver

IN OFFERING a few comments and suggestions on trends in mining practice, and the methods and tools of tomorrow's mining, perhaps it will be appropriate to start with the subject of education. Charles Kettering, one of the best-known scientists and experimentalists in the automotive industry once said, in effect, that tech- 111ca1 schools have to be carefid not to teach a lot of hard and fast rules that may have been true once, but aren't so any more, or won't be presently. Possibly the mining school of the future will concern itself less with what has happened and more with what is going to happen. It will be built about or around problems. Such a school will be judged, not by the number of its students but by the quality of its improvements. To such a school the industry will send for men to solve particular problems. The industry will doubtless at some time sup- port such a school financially though a lot of hard work will be required to organize miners to undertake such financing, primarily because the mining industry, other than that concerned with iron and steel, is too loosely knit. Each company tends to its own knitting too closely for its own good. Wouldn't it be splendid if the mining industry would finance a "problem school" as suggested by Mr. Kettering and others.

Jan 1, 1939

By Bernard Lewis

This report summarizes fundamental research end technical studies conducted in the Explosives and Physical Sciences Division, Region VIII, of the Bureau of Mines in the 2 years July l, 1950, to June 30, 1952. It is the fifteenth of a series of, ordinarily, annual reports whose aim has been to provide the reader with a resume of the research results that have appeared in published form during each fiscal year under the authorship of members of the staff. These are referred to throughout the report. ACKNOWLEDGMENTS Acknowledgments art, made to the following members of the Division wider whose mediate supervision the described studies were carried out. Stuart R. Brinkley, Jr., chief, Mathematical and Theoretical Physics Section, and special assistant to the chief of the division.

Jan 1, 1953

By A. R. Barnes, N. Stubina

Increasingly, gold producers are forced to treat ever more refractory ores. While ores containing pyrite, arsenopyrite and carbonaceous material have been subjected to complete pressure oxidation (PDX) as the standard process for such ores, recent improvements in fluid bed roasting technologies have led to a resurgence of interest in roasting as a viable alternative. The lower capital and operating costs of roaster installations add further impetus to this trend. The Extractive Metallurgy Group at Xstrata Process Support operates four fluid bed reactors of various sizes which have been utilised on a large number of projects to treat highly refractory ores. Preliminary mineralogical modelling of both the physical and chemical aspects of the roasting process and subsequent testing under carefully controlled conditions has allowed clients to obtain gold recoveries approaching or matching those achievable by PDX. The flexibility of the units to operate in various modes- " bubbling bed", circulating bed, two stage, sub-stoichiometric and combinations of these, and the range of sample sizes accommodated, from a few kilograms to a few tons, has enabled XPS to accommodate clients with a wide variety of gold bearing refractory ores from all over the world. This paper outlines the key challenges of fluid bed roasting of refractory gold ores, describes the methodology used to design the testwork program and provides some results from select test campaigns.

Jan 1, 2011

The Aluminum Company of America announced a temporary reduction of the operating rate at its primary aluminum plant at Palestine, TX where it is developing a new process to produce aluminum metal by electrolysis of aluminum chloride, Output will be reduced by half to about 7,500 tons per year while some improvements are being made on the chemical segment of the plant. The modifications were expected to take 3 to 4 years to complete. Alcan Alumininum Ltd., a major U.S. supplier of aluminum, reported declaration of force majeure on aluminum ingot shipment commitments following the shutdown of its primary aluminum plants at Arvida, Isle Maligne, and Beauharnois, Que. The shutdowns, which began early in June, resulted from management and labor differences.

Jan 1, 1979

By D. Harrington

Dust diseases are much before the public at present, but little reliable information on the subject is readily available to the layman; even those rated as experts usually have a more or less theoretical conception of these diseases, their causes, remedies, and prevention. Until recently little attention has been given to prevention, and the usual attitude of the engineer, upon whom the main reliance for prevention ultimately must devolve, has been to let "sleeping dogs lie" or, more definitely, to "let well enough alone." However, the "laissez faire" attitude no longer is tenable; in the past few years numerous conditions have caused those engaged in industry, including mining, to study the subject with a view to ascertaining the facts upon which to formulate remedial measures, primarily preventive. This bulletin is an attempt to assemble information in convenient form on effects of breathing dusts, largely in the mining and allied industries. The literature on this subject is so extensive that no attempt has been made to include all published material or all types of dust diseases but only to assemble some of the more outstanding data on several aspects of the subject, especially with reference to silicosis.

Jan 1, 1937

On April 5, the potlines at Consolidated Aluminum Corp.'s 35,000 ton-per-year primary aluminum smelter at Lake Charles, La., were frozen when natural gas lines were accidently cut by a dredge. Full production is expected to resume in 3 to 4 months. Three primary aluminum producers announced plans to restore much of the idled capacity in the Pacific Northwest as a result of a special power allocation by the Bonneville Power Administration. Reynolds Metals Co. planned to bring a total of 40,800 tons per year of capacity back onstream at Troutdale, Oreg., and Longview, Wash. The Aluminum Company of America (Alcoa) will restart half of a 23,500 ton-per-year potline at Vancouver, Wash. Kaiser Aluminum & Chemical Corp. planned to restart a 27,500 ton-per-year potline at Mead, Wash., and to bring an additional 10,000 to 20,000 tons per year back onstream at Mead and Tacoma, Wash.

Jan 1, 1980

By A. J. Williams, R. B. Corbett

"INTRODUCTION This investigation was undertaken to obtain information concerning the effects of boron in steel and its method of addition, so that boron, which is readily obtainable domestically, may be used to relieve the great demand for those scarce, strategic, alloying elements that hitherto have been considered necessary for the successful manufacture of quality steel.Previous Work Guillet 4/ seems to have been the first to predict that boron-bearing steel might have a possible industrial use when, in 1907, he published results of an investigation into the properties of steel containing 0.21 to 1.51 percent boron.Possibly Walter 2/ was the first to appreciate the fact that extremely small percentages of boron are effective in improving the properties of a steel. His patent, issued in 1924 claimed steels containing boron within the limits of 0.001 to 0.100 percent; furthermore, the specifications disclosed that boron increased the hardenability of steel and refined its grain structure. In 1937, Naton and Piwowarsky 6/ otherwise observed that boron increased the hardenablity of steel."

Jun 1, 1945