Search Documents

By Cyro Takano

This paper is a contribution to fundamentals data on the equilibrium metal/slag for refining silicon in relation to Ca and Al as impurities. Silicon containing 0.1% Al and no Ca was placed in contact with a slag of various contents of CaO, SiO2 and Al2O3. Slag Al2O3 contents were 11.4%, 25.1% and 29.6%, keeping the ratio %CaO/%SiO2 constant and equal to ~0.53. The experiments were conducted at 1550oC, in a graphite crucible with argon atmosphere. The equilibrium was observed with low and medium content of Al2O3. The derived activities coefficients of Ca and Al in dilute solution of Si presented good correlation with those of the literature. Parallel reactions with formations of SiO(g) and CO (g) were also observed.

Jan 1, 2006

By Michael S. Moats

As commercial copper electrorefineries look to expand their capacities by increasing their operating current density, the likelihood of anode passivation intensifies. To improve the industry?s understanding of the passivation phenomena, the role of anode composition was evaluated. While previous studies have focused on studying one impurity element at a time, this study was conducted using forty-four commercial electrorefining anode samples supplied by ten copper companies The passivation response of each sample was evaluated under accelerated galvanostatic conditions in synthetic copper electrowinning electrolyte at 65°C. This information allows for correlations between composition and passivation tendencies over a wide range of impurity elements and concentrations. It was found that selenium, tellurium, silver, lead and nickel accelerated passivation. It appeared that oxygen accelerated passivation when increased from 500 to 1500 ppm, but further increases did not have an effect. Arsenic was the only impurity found that inhibited passivation.

Jan 1, 2006

By Xiyun Yang

Magnetite was prepared by hydrogen reduction method. For a conversion to cobalt-modified magnetite, magnetite particles were suspended into a solution containing Co2+ and Fe2+ to precipitate a cobalt ferrite layer on the surface. pH value influences the particle composition directly, the desirable CoFe2O4 is obtained when pH value is 12. The coercivity increases with the increase of cobalt content, cobalt efficiency reaches a maximum value at cobalt content of 2.71wt%. With cobalt modification, magnetite particles have similar lattice constant and squareness ratio to that without cobalt modification. TEM and XPS analyses indicate that acicular morphology is retained during the coating process, the epitaxial growth layer consists of CoFe2O4and 0.3Co2O3CoFe2O4 at cobalt content of 2.71wt% and 5.03wt%, respectively.

Jan 1, 2006

By Kwang-Ho Lee

The Onsan copper smelter of LS-Nikko Copper Inc. has operated the Mitsubishi continuous process along with Outokumpu process since 1997. Mitsubishi process is a bath smelting process which needs adequate melts for smelting reaction in the furnace. After a campaign shutdown it requires time to make a start melt. Onsan smelter has had much experience in flash smelting, including the improvement of the concentrate burner which is one of the most important parts in a flash smelting furnace. Based on this experience, the lances of the Mitsubishi smelting furnace were modified in order to making the starter melt with flash reaction. In 2004, the flash reaction in the Mitsubishi S-furnace was completed and was able to make the starter melt using these modified lances. Although at that time it was still under development it reduced the time required to make the initial bath-melt by about half.

Jan 1, 2006

By Matthew Jeffrey

Leaching, cementation, electroplating and flotation are all electrochemical phenomenon. They are also key processes in the hydrometallurgical treatment of metals. Unfortunately electrochemical methods tend to be under-utilized when studying these processes and one possible reason for this is the confusion surrounding the large number of electrochemical techniques available. In this paper four former PhD students of Professor Ian Ritchie present an insight into how one electrochemical technique can be used to compliment rate/kinetic studies. The paper details how to perform the experiments, interpret data, and recognize complications with the results. Examples where this approach has been highly successful are presented, and include: cementation of zinc by aluminium, cementation of copper by nickel, cyanide leaching of gold and the cementation of gold thiourea by mild steel. The examples illustrate that this universal approach adopted by Ian Ritchie provides the key to understanding the mechanism of many hydrometallurgical reactions.

Jan 1, 2003

By Finn Olesen, Melina Garcia, Mark William Kennedy

"Furnace resistance is a function of the complex interrelationship between many factors including: operating practice, slag conductivity, temperature, power intensity, and geometry (electrode shape, diameter, spacing, immersion, slag depth, etc.).Accurate prediction of resistance is critical for success of the overall furnace design. The sizing of electrodes, columns, bus-bars, and transformers are all impacted. Estimation of minimum and maximum resistance or maximum operational current, as well as the maximum operating voltage are of fundamental importance.Various mathematical tools have been developed to assist designers with the selection of furnace dimensions and the prediction of resistance. Elkem found the methods of Downing and Urban 1965 and Westly 1975, to be particularly useful.In the current paper, comparisons are drawn between data from spent aluminum pot lining (SPL) demonstration testing at Elkem Bjolvefossen and predictions based on these classical tools and 3D finite element modeling (FEM) with COMSOL.®"

Jan 1, 2012

By Hani Henein

"Heat transfer between droplets/particles and a gas phase plays an important role in the transport of numerous materials processing operations. These include rapid solidification operations such as gas atomization and spray forming, as well as chemical systems such flash furnaces. Chemical reaction rates and solidification are dependent on the rate of gas-particle or gasdroplet heat transport. Using a heat transport model validated using single fluid atomization of molten droplets; the effect of process variables on heat losses from droplets was examined. In this work, the effect of type of gas, droplet size, gas temperature, gas-droplet relative velocity on the heat transport from AA606 l droplets was examined. The most critical of these process variables to heat transfer is identified and will be presented.IntroductionIn materials processing, droplets are often encountered and used in processing a wide range of liquids and slurries. The small size of the droplet enables high reaction rates or high solidification rates in many systems. In order to capitalize on these high rates of transport processes, sprays are· also developed to maximize throughput. The design of these sprays, however, does not account for the transport steps and rate limiting mechanisms at the droplet surface. Rather, spray design focuses on maximizing the break-up of a stream or slurry into small size droplets or controlling the spread of the spray. Spray systems in industrial use typically generate droplets of wide size distribution leading to a wide range of reaction times for each of the droplets. Often the generation of a spray involves a number of coupled phenomena such as stream break-up, droplet-gas transport, droplet size distribution and spray geometry. Using gas generated sprays, it is not possible to identify how individual process variables contribute and control each of these coupled phenomena. While many mathematical models have been developed of sprays and they attempt to simulate coupled droplet transport, they do not provide insight into the contributions of different mechanisms in heat transfer. This is primarily because the basic fundamental heat transport between droplet and gas cannot be isolated from other gas spray phenomena experimentally such as two-way thermal coupling [l]. Thus, experimental validation of heart transfer of large and complex industrial spray models is not carried out. Hence, the validity of spray models remains in question and the approach required to optimize spray processes cannot be clearly identified"

Jan 1, 2004

By Donald L. Stewart, Ken Overfield, Edward M. Williams

"Recent increases in energy cost have lead to a renewed focus on energy efficiency during aluminum melting operations to reduce fuel usage. The goals of a batch melting operation are to melt the charge using the minimum required energy, to melt the metal to the required temperature within the required timeframe, and to avoid generating unwanted contaminants by overheating the charge.The heat transfer efficiency of a conventional hydrocarbon fired aluminum melting furnace varies over the course of the melt cycle, depending on the conditions in the furnace. The purpose of this work was to develop a method of determining the transient heat transfer efficiency throughout the furnace cycle and to take advantage of this knowledge to optimize the melting process through furnace controls and proper production operations. This furnace survey methodology has been developed and used to evaluate a number of furnaces.Description of a Typical Batch Melting Furnace CycleA typical batch melting furnace cycle will consist of three stages:1. Charging – Solid metal charged through an open roof, solid or molten charged through an open door, and/or molten poured through a furnace blister2. Melting – From the time the door or roof is closed and the burners are turned to high fire until the charge is all liquid and has reached a temperature suitable for alloying (typically ~1350 °F / 730 °C)3. Holding – From the end of the melting stage until transfer or casting is completeIn some cases, further charging can take place after the melting cycle has started. This can happen when the entire solid charge will not fit in the furnace in one load, or if additional molten metal is added while the charge is melting. The bulk of the energy used in the melter is consumed during the melting cycle. The thermodynamic minimum energy requirements for melting pure aluminum are:• Energy required to heat pure aluminum from room temperature to the melting point at 1220°F (660°C) is 288 BTU/lb (670 kJ/kg)• Energy required to change state of pure aluminum from solid to liquid (heat of fusion) is 171 BTU/lb (397 kJ/kg)• Energy required to heat molten from melting point at 1220°F (660°C) to 1350°F (730°C) is 36 BTU/lb (83 kJ/kg)• Total energy required to melt a solid charge from room temperature to 1350°F (730°C ) is 495 BTU/lb (1151 kJ/kg)"

Jan 1, 2009

By K. Morsi, P. Mehra

"Spark plasma sintering has gained a considerable amount of attention over the past decade, due to its rapid sintering rates, and low temperature requirements, but has so far been usually limited to the production of simple geometries. The present paper examines the current-activated production of extended geometries through the process of spark plasma ""extrusion"". Of interest in the present study is exploratory research into the effect of electrical current activation on the reactive consolidation of powder systems to form intermetallic materials.IntroductionSpark Plasma Sintering (SPS) has been the subject of intense research over the past decade [ 1,2, 3,4,5,6]. The process boasts unique advantages which include ultra fast heating rates, shorter sintering times and lower sintering temperatures than needed in conventional sintering. The process is however limited to the generation of predominantly simple geometries. Recently one of the authors investigated the spark plasma extrusion of aluminum, where an aluminum powder compact is directly (Joule) heated through an applied DC electric current. Here extended geometries can be generated under the influence of electric current. A number of heating sources were identified including the heat source from current, i.e. Joule heating, frictional heating and heat from the deformation energy. However in the case of reactive powder systems, an extra ""one-time"" transient heating source can be supplied. By considering combustion synthesis of powders, this heating source is derived from the reaction between elemental powders to exothermically form a product at some ignition temperature [7]. This exothermic energy heats the compact to the maximum ""combustion temperature'', which could be hundreds of degrees higher than the ignition temperature. Hence a high temperature processing window (of short duration due to heat losses to the surroundings) becomes available in which the material is most suitable for stress-induced deformation and consolidation. For reactive spark plasma extrusion, two scenarios can be envisioned. The first is where the reactive powder compact is ignited through the application of current, and extruded within the high temperature processing window (also under the influence of current). The second scenario is to allow the heat of deformation/friction to heat the material during extrusion, to simultaneously force a reaction and consolidation. Here it is expected that the processing window will be very small if feasible."

Jan 1, 2011

By Shadia J. Ikhmayies

"Cadmium sulfide (CdS) in the form of thin films is an interesting material because it has a large variety of applications ranging from photovoltaic to luminescent devices. N-type CdS is usually used as a window layer in the heterojunction CdS/CdTe thin film solar cells. A review of the photoluminescence (PL) spectra ofn-type CdS thin films prepared by different techniques was performed. The effects of different dopants and impurities and the effects of temperature and deposition parameters on the PL spectra were discussed. Annealing in different atmospheres causes the changes in material structure and phase change from cubic to hexagonal phase which can be detected through the variations in the PL spectra. CdCh heat treatment improves the cystallinity of the films and enhances the exciton peaks and the green band in the PL spectra.IntroductionThin CdS films deserve attention because their expected gap emission lies very close to the highest sensitivity of the human eye. Thus, one might assume that thin CdS films are an appealing host for photonic devices [ l]. They have been used in a lot of applications including electronic and optoelectronic devices [2]. Thin films ofn-type CdS are widely used as a window layer in heterojunction solar cells such as CdS/CdTe solar cells. Doped and undoped CdS thin films can be obtained by different techniques such as; spray pyrolysis (SP) [3], chemical bath deposition (CBD) [2, 4], pulsed laser deposition [5, 6, 7], laser ablation [l], thermal evaporation [8].Several experimental techniques have been used in order to study semiconductor defects. In particular, photoluminescence (PL) has been shown as a powerful and sensitive tool in examining the crystal quality of polycrystalline thin films. PL can be used in the detection of defects which are radiative active. These defects can also act as traps in the transport of carriers [9]. The photoluminescence (PL) of thin film CdS is strongly influenced by the unbalanced stoichiometry, which is typical for CdS and is in general evoked by a Cd surplus. With increasing Cd content, the emission spectra move far below the gap to the red spectral range. Besides stoichiometry problems, independent of the material deposited, the PL properties of thin films depend on surface features and the influence of the interface between the film material and the substrate [10]."

Jan 1, 2013

By Emilia Visileanu, Eftalea Carpus

"The strategy of developing the Romanian textile industry sub-sectors envisages the achieving of certain superior production indices, from a physical and value point of view, in 2010, a quantitative increase of textile wastes by 14% in 2010 as compared to 2000, implicitly. The percentage of the turned-to-profit wastes will have an increasing tendency, from 53.6% in 2000 to 74.7% in 2010. The article synthetically presents the innovative elements of the technology of processing the industry textile wastes.1. Introduction“People will need to re-adopt this sense of rarity that has been forgotten over the last two centuries. Humans need to collect, sort, recover, going back to the old ideal of alchemists: complete the material cycle, turn waste into resource, reduce all forms of predatory behaviour as much as possible”Irrespective of the historical period, geographical positioning, economic power or employed technologies, wastes resulted and will result in a bigger or smaller quantity as long as life and activity on Earth go on. The negative effects of these over the environment factors and implicitly over population health are well known all over the world and not approaching this matter enough may have catastrophic consequences over life. Having in view these aspects, finding solutions for diminishing the general waste quantity and limiting the negative effects of those products is important, by effecting the reusing of the recyclable ones in the production processes as secondary raw materials, and by ecologically treating and storing those than cannot be reused.2. Experiments and researchesThe textile industry affects the environment by the high water, energy and chemical consumption, as well as by the high quantity of wastes that are the result of using an impressive number of chemical substances and technological processes.The development strategy of the Romanian textile industry sub-sectors foresees, for 2010, the achieving of certain higher production indices as compared to 2000, both in terms of materials (as merchandise) and in terms of value, which implicitly leads to a quantitative increase of wastes.The flexible, economic and ecologic technologies which include systems of waste preliminary preparing (cutting, opening) and conventional or non-conventional system of processing the recovered fibres lay at the basis of substantiating the activity of implementing the notion of zero wastes."

Jan 1, 2008

By Jean-Louis Dirion, Guy Depelsenaire, Patrick Sharrock, Souhila Kribi, Ange Nzihou, Jocelyn Ramaroson

"This study assesses the Novosol® process, an emerging technology developed by Solvay to treat heavy metals from dredged sediments using phosphoric acid. The main goal is to convert toxic metal ions, such as Pb2+, Cd2+, Zn2+ and Cu2+ to insoluble metallic phosphates. The effectiveness of the treatment was evaluated by performing the chemical reaction in a tubular reactor, followed by convective drying and maturation of the treated sediment at ambient temperature and finally thermal destruction of the organic matter by calcinations (500°C-700°C). Selected variables (acid concentration, volume fraction of solids, flow rate, drying and calcination temperature and time) were investigated. Laboratory scale experiments were carried out with various combinations of these parameters. The influence of the quantity of acid and the temperature of calcinations on physical properties of the sediment and stabilization of the heavy metals are discussed. Introduction The French territory counts 525 000 km of rivers which transport each year on average 6 million m3 of sediments. Their deposit causes the silting of channels, rivers and lakes. This completely natural phenomenon is exacerbated by the introduction of industrial and urban wastes into the erosion and sedimentation process. This silting leads to clogging of rivers, with a reduction in their flow rates. Consecutively, other problems appear, such as flooding risks, decrease of biological purification capacity and associated loss of the biodiversity. The presence of toxic compounds (from industrial, household or agricultural origins) in the sediments worsens the situation, and requires curing to restore the natural environment and its function. The dredged sediments are either spread on agricultural land, land tipped, confined or sent for chemical or physical treatment [12]. The first research programmes on toxic sediments appeared at the end of the Eighties in the United States, in Canada, in the Netherlands and in Germany. Several techniques of treatment were developed for the sediments; these techniques can be used alone or in combination. These techniques include extraction and concentration of the pollutants: the pollutants are isolated from the sedimentary matrix and the sediment is decontaminated. In some cases of organic contaminations, the pollutants are destroyed by chemical oxidation or biodegradation and in other cases, the contaminated material is either stabilized (mixed with hydraulic binders), or destroyed (incineration) [14,15]. Phytoremediation by afforestation has also been reported [19]."

Jan 1, 2008

By Feng Ningchuan, Guo Xueyi, Tian qinghua, Liang Sha

"In this study, copper adsorption by orange peel which was chemically treated with sodium hydroxide was investigated. The morphological and chemical characteristics of the adsorbent were evaluated by spectroscopy and N2-adsorption techniques. Equilibrium isotherms and kinetics were obtained and the effects of solutions pH, adsorbent concentrations and temperature were studied in batch experiments. Equilibrium was well described by Langmuir and Freundlich isotherms and kinetics was found to fit pseudo-second order type adsorptions kinetics. According to the Langmuir equation, the maximum adsorption capacities (qm) for Cu(II) was 50.25 mg·g-1 at pH 5.3. With the temperature increased from 16 to 60°C, copper removal decreased. The loaded adsorbent was regenerated using HCl solution and could be used repeatedly at five cycles with little loss of adsorption capacity. The results show additional chemical treatment of the adsorbent by NaOH, is favor of improving the adsorption capacity. Introduction Increased use of metals and chemicals in manufacture industries has resulted in generation of large quantities of effluent that contains high level of toxic heavy metals and it poses environmental-disposal problems due to its non-degradable, persistence nature and accumulation throughout the food chain [1, 2]. Copper is known to be a commonly used heavy metal. This metal, which found many useful applications in our life, is very harmful if charged into natural water resources and may pose finally a serious health hazard. Many methods, such as chemical precipitation, ion exchange, reverse osmosis and adsorption, etc., have been used for heavy metal ions removal from various aqueous solutions. In recent years, there has been considerable interests in use of biological materials including algae, bacteria, fungi, agricultural by-products and residues as adsorbents to remove toxic metals from aqueous solutions by adsorption [3-8]. Adsorption process has been extensively used to remove copper from aquatic medium using low cost adsorbents such as peanut husks [9], plant materials [10] and cellulose materials [11]. Among them, agricultural by-products and biomass are relatively cheap and show very high adsorption capacities. However, to apply untreated agricultural by-products as adsorbents has the disadvantages such as low adsorption capacity, high chemical oxygen demand (COD) and biological chemical demand (BOD) as well as total organic carbon (TOC), due to the release of soluble organic compounds contained in the plant materials such as lignin, tannin, pectin and cellulose, into the solutions [12-14]."

Jan 1, 2008

By R. P. King

The central idea presented in this paper is straight forward. Some fairly obscure mathematical techniques are presented from the fields of integral geometry and stereology and these techniques are shown to provide workable quantitative relationships from which the liberation spectrum of an ore after comminution can be determined. The experimental data that is required can be obtained very accurately and conveniently by image analysis of polished sections of the original ore. This quantitative mineralogical analysis provides a bridge that can link the worlds of the mineralogist and the mineral process engineer. This paper has been written to introduce this quantitative approach to a wider audience in the hope that the approach will be used more widely and that the basic linear intercept analysis data will be measured for a wider range of mineralogical textures. This could lead to a more comprehensive characterization of typical mineral ores that will be of considerable use in practical mineral processing.

Jan 1, 1991

By Aliye Arabaci

In the present investigation, an attempt has been made to study the reduction behavior of composite pellets consisting two different types of iron oxide fines (high and low grade) and coke or lignite fines as reducing agents. The reduction experiments were carried out under isothermal conditions and constant flow of nitrogen gas in the temperature range of 900 ? 1100 oC. The variables investigated are the reduction temperature, Cfix/Fe3O4 ratio, reduction time and reductant type. In the experiments carried out with Sivas Divrigi A head magnetite ores (high grade) at a temperature of 1100 oC, for 40 minutes and on the condition that Cfix/Fe3O4 ratio is 0.2, in which lignite and coke fines were used as reductant, degree of reduction was obtained as 91 % and 86 %, respectively. Whereas, in the experiments realized with Malatya-Hekimhan-Hasançelebi magnetite ores (low grade) on the same conditions by using lignite as the reductant, around 60 % degree of reduction was found.

Jan 1, 2008

By Elli Miettinen

In Copper Flash Smelting operation disturbances may lead into dust build-up in the gas train and off-gas handling system causing reduced heat recovery efficiency and process availability. Flue dust of a Copper Flash Smelting process heat recovery boiler has been characterized and its thermal conductivity and diffusivity have been determined. Dust accretions consist of several layers possessing varying particle sizes, densities, and thermal properties, with the binding phase usually being sulphate. All the dusts can be regarded as effective thermal insulators with thermal conductivity values of less than 2 W/mK and thermal diffusivity values of less than 0.005 cm2/s. Porosity can be regarded as a fairly good indicator of the thermal transport efficiency of these types of materials, but the material microstructure must also be considered. The results can be used in the dimensioning of metallurgical heat recovery boilers and they also provide accurate input data for process models.

Jan 1, 2009

By Frank M. Kimmerle

Spent Potlining (SPL) contains recoverable chemical elements (C, F, Na and Al) which are lost in stabilization or immobilization processes primarily aimed at eliminating cyanides and reducing leach rates of soluble fluorides prior to landfiling. They can be recovered in a variety of mineral forms for recycling in the aluminum industry and elsewhere. Alcan has developed a cost-effective hydrometallurgical route, combining a number of proven unit processes to destroy cyanides, recycle the chemical values and provide a zero-discharge process. Pilot plant studies of this Low Caustic Leach and Liming (LCL&L) Process prove that the fluoride scan be converted to acid grade fluorspar, while the sodium and aluminum are recovered as a sodium aluminate and caustic feed to the Bayer Plant operations. The remaining brick and carbon fraction constitutes a high ash solid fuel which meets TCLP leach criteria and whose reduced sodium content enhances its value as a chemical reducing agent.

Jan 1, 1994

By S. Y. Tan

As CMOS devices are scaled down into nano-region, SiO2 dielectric is approaching its physical and electrical limits. High-k material has been investigated widely in recent years, and gate oxide take place growth oxide with Hf-based below 45nm gate length technology node has been shown. The phenomenon of interfacial property between bulk silicon and gate dielectric materials (HfO2 and HfSiO) was focused. A comparison of capacitance-voltage (C-V) characteristic of gate insulator was presented. Furthermore, the electrical property and thermal stability of high-k dielectric materials at various post deposit anneal (PDA) temperatures were established. The X-Ray diffraction technique was (XRD) utilized to analyze crystallization of the thin films, and the X-ray photoelectron spectroscopy (XPS) was applied for surface chemical bounding energy to identify the silicon and dielectric layers. Results show that HfSiO films have exhibited a superior performance on both thermal stability and electrical performance.

Jan 1, 2009

By Cheng Yan, Yugang Li, Qian Wang, Lizhi Zhang

In continuous casting process, mold powder has lots of metallurgical effects, such as covering the molten steel to prevent liquid steel from oxidation by air, preserving heat for top layer liquid steel, lubricating initial shell and so on. However, mold powder also can deteriorate the quality of final products obviously after the entrapment of mold powder in steel. In the present work, based on the similarity theory the effect of technological parameters on mold powder entrainment was investigated by water model. Experiment was carried out in the water mold using oil and water to simulate slag and steel, respectively. The results showed that increasing casting speed increased the water-oil interfacial fluctuation and entrainment frequency; viscosity of oil also had a great impact on the interface fluctuation and entrainment; water-oil interfacial tension effect the entrainment while not changing the interfacial fluctuation; submergence depth had little impact on entrainment and interfacial fluctuation.

Jan 1, 2015

By Chao Zhang, Kexin Jiao, Yi Qian, Jianliang Zhang

Now low-grade iron ore were widely used. However, one prominent problem is that the content of trace elements is higher than that in high quality iron ore. For the requirement of the content of Mn, Cr, Ni, Cu, and Ti in hot-rolled steel sheet and strip, the upper limits of these elements in sinter will be studied in this paper. Using the activity model of aggregation of electronic phased slag composition, the distribution ratio of each element in converter is analyzed and the content of each element in hot metal is calculated. Furthermore, through the thermodynamics method, the distribution ratio of each element in BF is analyzed and the content of each element in raw material is calculated. The upper limits of Mn, Cr, Ni, Cu, and Ti in sinter can be determined by calculating, the values are as follows: Mn 0.767%; Cr 0.552%; Ni 0.055%; Cu 0.159%; Ti 0.108%.

Jan 1, 2015