Search Documents

By Sung-Joo Lee, Gi-Chon Han, Nam-Il Um, Hee-Chan Cho

"In Korea, almost all of bottom ash produced by coal power plants is disposed of in ash ponds. Ash storage areas comprise more than 80% of most coal power plant sites. This disposal method is causing environmental problems and a managerial burden for plant operators. In this study, investigations to develop a beneficiation process for separating coal pond ash into various products were undertaken. To improve efficiency of the separation, coal ash was separated by sizes and each size fraction was subject to various beneficiation processes. The separation process used were flotation (-200 mesh size), hindered settling (16x200) and tabling (16x200 and 8x16 mesh). The results showed that various marketable products, such as lightweight aggregate, sand, high-carbon fuel, could be recovered from coal pond ash using simple physical separation techniques.IntroductionDue to the increased use of coals every year, about fifty million ton of coals were used in 2007 alone. As a result, about 6 million tons of coal ash were generated. In Korea, the coal bottom ash is classified as a general industrial waste and is usually disposed of in ash ponds. The costs for this disposal method continue to increase due to rising costs of site management and development and more strict environmental regulation. Therefore, utilities are constantly looking for ways to increase utilization of coal ash. In this study, various beneficiation processes were evaluated to examine the possibility of separating coal pond ash into various products which can be used as aggregates and high-carbon fuel."

Jan 1, 2008

By C. H. Quan

Solvent extraction tests were carried out on a rare earth chloride solution derived from monazite processing to determine the effect of extractant and diluent on the distribution coefficients between organic and aqueous phases, and the separation factor between rare earths. The extractants were 20% by volume di-2-ethyl-hexyl phosphoric acid (DZEHPA) or 2-ethyl-hexyl phosphonic acid (Ionquest® 801). Four Shellsol diluents were tested ranging from nil to 100% aromatic content. D2EHPA gave the highest rare earth extraction for a given pH but was less selective than Ionquest. The geometric mean separation factor between adjacent rare earths varied from 2.41-2.56 for D2EHPA to 2.62-3.01 for Ionquest. The nil-aromatic diluents (Shellsol 2037 and 2358) gave better separation factors in Ionquest but, in D2EHPA, were slightly inferior to the 100% aromatic diluent Shellsol AB. Yttrium behaved as a pseudo-heavy rare earth with a distribution coefficient lying between Ho and Er, as expected from its ionic radius.

Jan 1, 1992

By B. R. Baldock, R. W. Matusewicz

The recycling of used computer boards is a key industry activity for the recovery of precious metals. The safe and effective separation of metallic from non-metallic materials and subsequent processing of these secondary materials to provide high recoveries of values and excellent environmental performance are critical process requirements. Ausmelt Technology has been used commercially in four plants for the recovery of precious metals and has also been used very successfully at pilot plant scale to process computer boards. This work and its application to commercial operations with particular reference to processing conditions and environmental performance are reviewed.

Jan 1, 2000

By Xiang Sun, Zheng Zhang, Jiann-Yang Hwang, Zhiwei Peng

"Nickel oxide nanoparticles were synthesized using sodium dodecyl sulfate as the surfactant and urea as the hydrolyzing agent and different calcination temperatures and time were selected for preparation. Nitrogen adsorption (BET), X-ray diffraction (XRD) and scanning electron microscope (SEM) were subsequently used to characterize the prepared samples. The effect of an external electric field on hydrogen adsorption over a prepared nickel oxide was carried out. The electric filed was introduced by a piezoelectric element, which is capable of autogenously generating charges under hydrogen pressure. Increased hydrogen adsorption was obtained from this study, which indicated a stronger interaction between the adsorbent surface and hydrogen.IntroductionMetal oxide has attracted great attention for adsorption because of their wide application in catalysis [1-7], gas storage [8,9] and sensors [10,11]. However, with respect to the usage in hydrogen adsorption, few research outcomes have been reported [12,13], since there remains the difficult task of synthesizing highly porous metal oxides with unsaturated metal centers, which account for the strong interaction with hydrogen [14,15]. Nickel oxides are polar materials with an intrinsic dipole moment. The external applied electric field could further enhance the dipole moment so that the hydrogen could be more strongly adsorbed."

Jan 1, 2012

By Guozhu Ye

Hydrometallurgical zinc recovery from EAF dust has several advantages compared to pyrometallurgical alternatives in terms of low temperature operation, lower energy consumption and higher flexibility. Many hydrometallurgical processes have been suggested and tested over the years without success. The main reasons are: -Low leaching yield of zinc due to the fact that a high fraction of ZnO in the EAF dust exists in the zinc ferrite structure which makes selective leaching of ZnO not possible -Many of the proposals could not handle the halide in the EAF dust To eliminate these two disadvantages, two zinc ferrite elimination concepts have been tested and developed in the REZIN project of the EU 5th Framework Programme. The two concepts for zinc ferrite elimination could be shortly described by the following chemical reactions: A. ZnOFe2O3 + 2CaO = Ca2Fe2O5 + ZnOfree B. ZnOFe2O3 + C = Femet + CO/CO2 + ZnOfree These two concepts were investigated in details in combination with a subsequent leaching step using the novel EZINC process for recovery of zinc from EAF dust. Leaching of pretreated samples has shown great increases of a zinc recovery yield. A zinc recovery of over 90 % could be reached, as compared to about 50 % for no-pretreated samples. This paper will describe the two concepts in details.

Jan 1, 2006

By Raj Mutharasan

The phenomena of gas-molten metal reactions for the production of metal matrix composites consist typically of a combination of one or more gas transport steps and a liquid gas reaction step. Reaction products include such strength enhancers, grain refiners, or high thermal conductivity phases as TiC, AIN, SIC, Si3N4, TiN in aluminum alloys. Nitrides, carbides and oxides can be produced at various volume fractions and in fairly fine sizes (500 am to 5 um) in laboratory melts by Reactive Gas Injection method (RGI). Gas injection methodology to produce the reinforcements is attractive because it can potentially be scaled to production scales in excess of 10,000 kg/h. For continuous production, the reactant molten metal can be continuously fed into the .crucible where the reactive gas is injected. The molten metal phase reactant may also be involved in a controlling transport step, depending on its concentration and viscosity. It is well known that the reaction product reinforcement size and shape of these phases have significant impact on the physical, mechanical and thermal properties. The current state of knowledge is unable to predict the kinetics and growth of solid reaction products obtained. The primary goal is to develop a fundamental framework for the understanding and prediction of the particle size in such reaction systems. In addition, the role of gas transport, liquid hydrodynamics and decomposition are important issues. A reaction-transport model is being developed using a reaction, transport, and thermodynamic framework, both at macro and at atomistic level to assess gas - liquid interactions.

Jan 1, 1996

By S. Vukcocic

A long term research project is in progress to establish the parameters of an acid leach process to recover alumina 'froui' high-iron and/or low-iron white bauxites, kaolinite, coal. ash and copper mine tailing. In this paper the results of acid leaching of copper flotation tailing for the removal of alumina are presented. The tailing is very complex material which contains 25% Al203 in the -10 lim fraction. X-ray diffraction indicates presence of quartz, kaolinite and minor 'alunite. After classification and ,separation of the -10 lim fraction, the raw material is fired to 550GC and leached at 90GC. Filtration is applied for the separation of white silicate residue form leach liquid. After the purification step, aluminum salt is crystallized from the solution, and calcined to alumina. Kinetic correlation and regime, of the processes are defined and presented in the paper.

Jan 1, 1992

By S. Saptharishi

Selenium, which is a 6A group element of the periodic table, constitutes about 7x10-5 % of the earth?s crust. Even though selenium is a dispersed element with respect to its commercial exploitation, it is capable of forming number of minerals and nearly forty selenium minerals have been identified, out of which the copper ores are the richest sources of selenium. Electronics industries and glass industries are the major consumers of selenium, while pharma grade selenium used as micronutrient for humans and animals. Various methods have been developed to recover selenium as a by-product from copper anode slime during copper refining. Selenium being amphoteric in nature, it is soluble in both acid and alkali. While acid roast process is widely used, considerable work has been carried out in Russia for recovering selenium through alkali route. This paper enlightens the process developed at Central Research and Development Laboratory, for recovering selenium from decopperised slime through alkali pressure leaching. The decopperised slime is pressure leached with alkali under oxidizing conditions by which almost all the selenium present is converted to alkali selenate, which is easily separable from the rest of the decopperised slime. The solution so obtained is neutralized, during which, most of the impurities are precipitated out. Then selenium is precipitated in its elemental form upon purging sulphur-di-oxide under warm acidic medium. The purity of the selenium obtained by this process is higher than that of the selenium from acid roast process. Moreover selenium can be crystallized as sodium selenate and it can be marketed. The acidic content of the effluent is recovered and it is recycled back to the process. The sodium content of the effluent is converted into high purity sodium sulphate, which is marketable. The hazardous waste containing arsenic is precipitated as its sulphide and can be disposed off as landfill.

Jan 1, 2006

By Xin Wang, Hongmin Zhu, Shuqiang Jiao

"The behavior of electrochemically depositing silicon in a molten high-melting-point fluoride electrolyte was studied at 1300 °C. The cathodic product was characterized by XRD, SEM and EDS. Though the analysis of structure and composition of deposition, it could certify that silicon deposited on the Mo rod and alloyed with molybdenum. A series of tests had been performed on the cathodic behavior of Si4+ ions in BaF 2-CaF 2-Na2S iF 6 molten salt. The influence of electrochemical parameters on the cathodic deposition of silicon was also investigated. The electrochemical behavior of Si4+ ions in applied fluoride melts was observed to proceed according to one-step reaction.IntroductionGreenhouse warming has been a serious global issue. lt is increasingly urgent for clean and renewable energy. Effective utilization of clean and inexhaustible solar energy has become very important. Solar cell (especially poly-Si solar cell) production has significantly increased this decade, as there is a growing demand for clean energy. Since the early 1980s, the annual growth of the photovoltaic (PY) solar cell industry is more than 30%. More than 90% of the annual solar cell production is based on crystalline silicon wafers. This rapid growth leads to a shortage of silicon of the adequate quality and price for the continued growth of this industry [I , 2J. The most conunonly used technology to produce silicon is the so-called Siemens process. This technology, involves the forming of gaseous Si compounds such as trichlorosilane (SiHCli) or silane (SiH4) with subsequent thermal decomposition of these back to Si. This technology is associated with transformations from solid to gas, and then back to solid phase, which lead to high irreversible thermodynamic losses and subsequent high energy consumption, the energy cost being around 200kWh/kg Si [3l_ The purity of the material from this process is very high (9 to 11 N). In general, what is needed for solar cell purposes are reported to require 4 to 6 N quality. To promote continued growth of the silicon-based PY industry, there is need for a low-energy silicon production process which can produce large amounts of silicon with an acceptable quality and a lower price particularly."

Jan 1, 2012

By M. Cross, K. Pericleous, A. Mouchmov

"Copper - nickel - sulphide alloys are typically cooled and solidified in 4, 8 and 16 tonne ingots. These ingots exhibit a variation of grain size distribution and macro segregation of the prime alloy components throughout. The former is assumed to be primarily due to the dominant relation between grain growth rate and the cooling profile, whilst the latter is heavily influenced by buoyancy driven residual convection. The objective of this research program is to examine the extent to which it is possible to develop a 'broad brush' computational model of this ingot cooling process, that can predict some 'integral' measure of the grain size (e.g. average diameter) and the macro-segregation as a function of operating conditions.A computational modeling software framework, PHYSICA+ is used to simulate the complex process of ingot casting, which involves coupling between different physical phenomena. The entire model involves:(i) a 'broad brush' grain growth model that could be used in the prediction of micro/macro-structure of alloy ingot cooling processes,(ii) a heat transfer and solidification model which takes into account a second phase transformation of P NhS2 to heazlewoodite, and (iii) NS fluid flow simulation which provides a good basis for further micro/macro segregation modeling.At this stage some results of the 3D convection driven thermal cooling and solidification profiles will be shown, together with the 'integral' model for the grain size prediction."

Jan 1, 2001

By Tomoji Kawai

"The Pulsed Laser Deposition method using multi-targets is extremely useful for the creation of functional multi-layers and variety of artificial lattices. The topic of the present talk is on the creation of ''Function hannonized artificial lattices by laser ablation"" made of the combined magnetic, ferroelectiric and superconducting layers. The outline of talk is,1. Features of Pulsed Laser Deposition method (Laser Molecular RHEED and S1M/AFM.2. Creation of magnetic, dielectric and superconducting artificial lattices by Pulsed Laser Deposition.3. Novel properties of function harmonized artificial lattices: especially on the magnetic and magnetoresistive artificial The outline of talk is, lattices made of3d transition metal oxides."

Jan 1, 2000

By Jari Aromaa, Antti Kekki, Olof Forsén

"The deposition of copper on inert substrate depends on the number of active sites that will react at certain overpotential. The critical overpotential depends on surface morphology, surface film resistance and additives on cathode surface. The effects of surface properties on copper nucleation and growth rates were studied for used stainless steel blanks from several tankhouses. The surfaces of the blanks were characterized with electrochemical and mechanical methods. Electrochemical deposition tests were done at current density of 300 A/m2 for 10, 30 and 60 seconds. The nucleation density and copper coverage were estimated using image analysis. The surface film resistance did not correlate with copper growth. Increasing surface roughness correlated with lower copper growth.IntroductionStainless steel cathode blanks in copper electrorefming are usually made of AISI 3 I6L type steel. They have a typical lifetime over 10 years. During use the surface will collect deposits and become rough due to wear and corrosion. These factors can affect the nucleation and growth of copper. The nucleation and deposition of copper on inert substrate depends on the number of active sites that will react at certain overpotential. The critical overpotential can depend on surface film resistance, surface morphology, and additives adsorbed on cathode surface.The deposition potential of metallic ions on a foreign substrate is usually higher than the deposition potential on the electrode made of the same metal due to crystallographic substrate/metal misfit [I]. If the substrate has traces of the depositing metal they will be preferential growth sites. For a smooth deposit a large number of simultaneous nuclei is necessary. However, excessive nucleation density can lead to porous deposits [2]. Surface films of good conductivity are needed for dense nucleation and small nuclei. On cathode blanks the number of active sites increases with increasing surface film conductivity [3-5] and/or surface film porosity [6]. On AISI 3 I6 L stainless steel a more resistive oxide has been found to limit favourable sites for copper nucleation and more conductive film promoted high-density copper nucleation [7]. Also Urda-Kiel et al. have concluded that thicker oxide layers on AISI 304 stainless steel resulted in lower nucleation [8]. Increase in overpotential or current density activates more and more of the potential nucleation sites and this can be seen as higher number of nuclei [9] or smaller average distance between nuclei [10]."

Jan 1, 2012

By Yinlun Huang, Cristina Piluso

"Industrial sustainability looks to improve material and energy efficiencies, product quality and variety, and productivity within an industrial zone, thus pursuing the long-term sustainable development of the region. This paper introduces a systems-based modeling methodology, which provides industrial leaders with the ability to evaluate future production options to determine the path with the highest positive impact on both their own sustainability and the sustainability of the overall industrial zone. A comprehensive study on sustainable development of an auto-manufacturing focused industrial zone under uncertainty is illustrated. Introduction Sustainable development refers to a continuous process of improvements that must be followed in order to achieve a state of sustainability. In its most general form, a widely accepted definition of sustainable development was identified in the Brundtland Report as “development that meets the needs of the present without compromising the ability of future generations to meet their own needs” [1]. Sustainability will occur when the material and social conditions can be maintained or improved for human health and the environment over time without exceeding the ecological capabilities that support them [2]. An industrial zone is defined as a geographic area comprised of a network of industrial sectors, each composed of a number of entities. Such a zone is highly integrated and complex, and contains numerous uncertainties due to each industry’s extreme dependencies on its suppliers and customers throughout the product supply chain. In the context of an industrial zone, sustainable development refers to the continuous process of advancements in the zone, and the entities that comprise it, creating more value, wealth, and profits (economically viable dimension), providing environmentally benign products with less raw material consumption and waste generation (environmentally compatible dimension), and collaboration and a direct relationship among all involved in the supply chain, i.e. the corporations, employees, suppliers, investors, communities, customers, etc. (socially responsible dimension). These are the triple bottom lines of industrial sustainability. In order for economic, environmental, and social sustainability improvements to be successfully implemented within an industrial zone, the industrial decision makers must possess system-wide analysis abilities. The analysis of the sustainable development of an industrial zone involves decisions at the local, regional, or national levels, which are complex and involves handling of ill-defined parameters with a high degree of uncertainty due to the imperfect understanding of the underlying issues [3]. This work focuses strictly on the uncertainties in future zone planning and a method and a scenario based approach that can be used to evaluate the sustainable development of an industrial zone among these uncertainties."

Jan 1, 2008

By A. Bruynesteyn

It is well known that most North American gold deposits are of a hydrothermal origin and therefore they are often associated with sulphide minerals such as pyrite and arsenopyrite. When the precious metals in such ores are held captive inside sulphide crystals, the ores are called refractory because they do not respond to treatment by direct cyanidation. In these cases, it is necessary to recover the contained precious metals using high temperature treatments such as smelting or roasting, or high pressure leaching processes to break down the sulphide crystal matrices and thus liberate the precious metals for subsequent extraction by cyanidation. Sulphidic gold ores containing arsenic and/or antimony are considerably more difficult to treat because, in addition to their refractory nature, the arsenic and antimony content also prohibits treatment by direct cyanidation or amalgamation. These ores must be milled and their sulphidic gold values concentrated by flotation. The resultant concentrates must then be roasted to break down the sulphides before cyanide treatment can be applied.

Jan 1, 1985

By J. Antonio Barrera-Godinez, S. E. James, J. Sun

The solvent extraction separation of iron from a zinc sulfate medium using DEHPA was investigated. After loading, the ferric ions were reduced in the organic phase using metallic zinc. The ferrous ions produced could be easily stripped into a sulfate solution with pH values in the range of 1.4 to 2.0. The small, laboratory scale pilot system used in this study allowed for continuous cycling of the organic and strip aqueous solutions. It was possible to establish and evaluate a series of steady state conditions under selected operating paiameters. The effects of processing parameters such as solution chemistry, flow rates, zinc metal loading and pH on iron recovery and efficiency were also evaluated. Under proper conditions, it was possible to remove about 5 g/L iron from the organic phase in one stage and to produce a concentrated iron sulfate strip solution containing ferrous ion concentrations in the range of 90 to 130 g/L. Preliminary feasibility tests were also made on electrowinning metallic iron from the strip solutions and crystallizing ferrous sulfate as a means of making a marketable iron product.

Jan 1, 2000

By Dan Wang, Qian Li, Yong-bin Yang, Tao Jiang

"Thiosulfate is one of the most promising non-cyanide lixiviants for gold leaching. However, the undesirable reaction between thiosulfate and copper (II) gives rise to increased reagent consumption, which results in high cost and huge limit to its development. This paper presents study on the effect of ammonia, copper (II) and Cu(NH3)l+ ions on the oxidative decomposition of thioulfate. It shows that the presence of copper (II) and Cu(NH3)l+ can significantly increase the thiosulfate oxidation, while ammonia is relatively unaffected. The oxidation of thiosulfate by copper(II) in the absence of ammonia is fast at first and then decreases as time increased within a certain time, which can postulate that an intermediate product is responsible for the decreased consumption. The effect of ammonia is depended on the interaction with copper (II), which was found to significantly affect the consumption of thiosulfate.IntroductionFor over one century cyanidation is widely used in industrial production of gold, due to its simplity of process and low cost of production. However, cyanide is a highly toxic chemical reagent used dangerously and brings serious environmental pollution. What's more, cyanidation has slow speed of leaching gold and poorly leaching effective for refractory ores. With the exhausting of free-milling gold ores and promoted environmental protection requests, the disadvantage of cyanidation becomes a growing problem. In recent years, more and more research activities have been focused on alternative processes using non-cyanide lixiviants. Among the non-cyanide lixiviants, thiosulfate is considered as the most promising one[l-5].Compared to cyanide, thiosulfate is an inexpensive, nontoxic and less-pollution reagent, which can form complexes with many metal ions. Thiosulfate leaching of gold has an acceptable leaching rate and is insensitivity to impurities. Moreover it presents advantage on the treatment of refractory gold ores such as carbonaceous gold ores, copper gold ores, complex arsenic and sulfur gold ores, and so on[6]."

Jan 1, 2013

By J. P. Downey, L. G. Twidwell

"The high density sludge process (HDS) is a commercially proven acid rock drainage wastewater treatment process that is based on acid neutralization and metal precipitation. Previous studies have established that metal removal efficiencies in precipitation-based wastewater treatment applications can be improved through metal ion adsorption on ferrihydrite and/or aluminummodified ferrihydrite. This study was conducted specifically to determine whether the metals removal efficiencies at an existing industrial facility could be improved by promoting ferrihydrite and/or aluminum-modified ferrihydrite precipitation during the pH adjustment stages of the HDS process. The metal tenors of the treated wastewater samples are compared with those obtained through baseline experiments, which were designed to simulate the conventional HDS operation. The subject metals were: aluminum, arsenic, cadmium, copper, iron, manganese, nickel, and zinc.IntroductionThe HDS process is commercially proven ARD wastewater treatment technology that involves raising the wastewater pH by adding hydrated lime, caustic soda, or another alkaline substance. In addition to neutralizing the acidity, many dissolved metals precipitate as pH is elevated. Waste volume is minimized by capturing and immobilizing the precipitated solids.However, ARD streams characteristically contain multiple dissolved metal species. The response of various metals to pH adjustment in the HDS process is neither uniform nor quantitative, so minor to trace concentrations typically remain in the treated wastewater following solid-liquid separation. The effectiveness and applicability of the process would be improved if a means were found to further reduce the metal concentrations.Previous research and industrial applications have proven that metal ion adsorption on ferrihydrite (FH) and/or aluminum-modified ferrihydrite (AMF) increase metal removal efficiencies. Ferrihydrite and AMF are considered ideal for cation and anion adsorption from an aqueous solution at the appropriate pH [1]. Ferrihydrate adsorption of dissolved heavy metals is widely practiced throughout the world [2, 3]. It is established that FH and AMF effectively adsorb As contained in aqueous solutions [4]. Arsenic removal by adsorption on FH is the U.S. Environmental Protection Agency’s (EPA) Best Demonstrated Available Technology [5]. Twidwell and Leonhard also demonstrated that heavy metals (Cd, Cu, Ni, and Zn) are effectively removed from solution by coprecipitation/adsorption using AMF and FH [6]."

Jan 1, 2008

By Keri Ledford, Stephanie Lin, Jason Nadler

Novel processes are being developed to fabricate thin copper thermal wick samples of a targeted porous microstructure. Structures of desired porosity, thisckness and pore size and distribution are achieved by tayloring the incorporation of sacrificial polymer beads in to slurry precursors. The thickness of the final structure is dictated by precisely controllable slurry application methods, such as spin coating. Ina subsequent heat treatment, th epolymer components thermally decompose and the remaining copper particles sinter to form a reticulated foam. The resulting microstructures are characterized in terms of porosity, permeability and specific surface area.

Jan 1, 2012

By R. M. Luna-Sánchez

Electrochemical studies, particularly Evans? diagrams, have been employed in hydrometallurgy to simulate and explain the redox phenomena that take place at mineral and metal surfaces during operations such as leaching and cementation. However, despite their utility, in some cases, the combination of the cathodic and anodic branches, determined separately, does not reproduce the chemical environment present when both processes occur simultaneously on a specific surface. In the present paper, limitations of Evans? diagrams are analyzed through two examples: silver sulfide cyanidation and gold cementation on zinc. In both cases, the surface kinetics are sensitive to the local pH and cyanide levels. When the electrochemical oxidation of silver sulfide or the reduction of gold are performed in the absence of its corresponding redox reaction, the local pH obtained does not simulate the real situation and the combined reaction kinetics may be very different from those determined from the Evans? diagrams.

Jan 1, 2003

By A. Mejias, M. A. Garcia, G. Diaz

During 1997 and 1998 two successful zinc feasibility studies, Skorpion and Sanyati, were carried out by Tecnicas Reunidas based on the modified ZINCEX® technology. The technical viability of each project was proved during more than 600 h of continuous running in a pilot plant. The Skorpion zinc project would recover 150,000 t SHG Zn/y from an oxidized zinc ore of a Namibian mine. The economical study showed that the plant would have the lowest production costs in the world. The Sanyati zinc project would treat a bleed from an existing copper refinery in Zimbabwe to recover 5,000 t SHG Zn/y. In the first case the electrowinning cellhouse was supplied by Union Miniere and in the second by Tecnicas Reunidas. This article highlights the pilot plant results and the advantages of the proposed process over conventional zinc production practices.

Jan 1, 2000