Search Documents

By Robert H. Hsu

Palladium finely dispersed in a substrate of kieselguhr, Pd/k for short, has been successfully used for hydrogen storage, separation and pumping for a number of years at the Savannah River Site (SRS). Recently SRS has developed a new pd/k flow through bed (FTB) prototype for separating hydrogen from other gases and simultaneously storing the hydrogen on palladium. The FTB uses single-pass liquid nitrogen cooling during hydrogen absorption/separation/storage and electrical heating for desorption/unloading of hydrogen. Fourteen absorption-desorption or loading/unloading cycles using hydrogen have been conducted with the new FTB prototype. Test results show that all design performance objectives have been successfully achieved: recover 295% of hydrogen gas from feed gas, produce 99.9% hydrogen product gas and < 5% hydrogen in discharge gas. This paper will discuss characteristics of the palladium-coated kieselguhr or diatomaceous earth, design and operation of the FTB, and results of performance tests such as separation efficiency, hydrogen storage capacity and system heat transfer characteristics.

Jan 1, 2002

By P. Blazy

A hydrometallurgical procedure for the recovery of metal from ore, particularly of copper from sulphide materials is described. In the course of this procedure, the raw material is first of all submitted to the action of an appropriate reducing system and then treated with a ferric salt solution which brings about the selective solubilisation of the elements to be recovered with respect to those constituting the pyritic phase. This procedure is investigated using two ore samples proceeding from massive sulphide deposits, presenting different chemical and mine- ralogical characteristics. The results of this investigation are compared with those obtained by a classical process employing a ferric salt solution. It appears that one solubilisation of copper takes place under particularly advantageous conditions when our procedure is used. The principal parameters affecting leaching of zinc, lead and copper are examined. The selectivity of this treatment is evaluated by following the change during the treatment in the pyritic phase.

Jan 1, 1976

By Yasumasa Hattori

An extensive study including fluid dynamic calculations, cold model tests, pilot plant tests as well as measurements in a commercial flash furnace was carried out in order to develop a new Sumitomo flash smelting concentrate burner. The pressure measurements in the commercial burner indicated that the premixing of the concentrate and reaction air in a burner was insufficient. Pilot plant tests showed that enhancement of the premixing of the concentrate and reaction air is very effective for improving the burner performance. Using the additional pressure drop of the reaction air as an indicator of the premixing, a new type Sumitomo premixed concentrate burner was developed.

Jan 1, 2003

By T. N. Chan

This paper provides some general discussions on the development of a new beneficiation process for the treatment of a highly complex monazite orebody located at Mt Weld, Laverton, Western Australia. The complexity of this rare earth ore and the associated problems encountered in ore preparation, desliming and flotation in beneficiation during the development study stage and the solutions to these problems are reviewed.

Jan 1, 1992

By Hartmut Rossel

VAW aluminium AG has built a "Recycling-Technikum" (Recycling Research Centre) to add a new arm to the company&apos;s Corporate Research and Development Department. The Recycling Research Centre, a pilot plant for scientific research, has been in operation since September 1993. These state-of-the-art facilities allow the investigation and optimisation of recycling techniques in &apos;a global way and in detail. Research is concentrated on the unit operations - processing, melting and waste-gas purification - with the available installations making it possible to compare different alternative process combinations on a 100-kg scale. One of the main targets of VAW research is the development of recycling techniques for packaging. The paper presents an approach to recover the aluminium contained in flexible packaging materials using an integrated melting and waste-gas purification system.

Jan 1, 1995

By K. C. Mills, P. N. Quested, A. P. Day, R. F. Brooks

"Methods have been developed to measure the physical properties of molten materials relevant to the fluid flow in high temperature processes. Data for the densities, viscosities and surface tensions of Al-, Ni- and Fe-based alloys are compared with (i) values for the pure metals and (ii) estimated values obtained from models making use of chemical composition of the alloy. Experimental values for metallurgical slags are also given and compared with estimated values.1 IntroductionPhysical property data has proved very useful in improving process control and product quality. For instance, in the continuous casting of steel the viscosity (TJ) of the mould flux is important since it determines (i) the optimum casting conditions, nVc = 2.5±1 dPas (m min-1) where V c is the casting speed and (ii) the level of slag entrapment (which leads to inclusions) in the metal. Thus data for properties like viscosity are exceedingly useful in understanding the process and the problems encountered and the causes of defects and problems.Another interesting development which has helped to increase our knowledge of processes and improve process control and product quality is the development of mathematical models of the fluid and heat flow in the process. These models have been developed to the stage where one of the prime requirements is for good physical property data for the industrial materials involved. Recently, Oxley [1] has shown that the use of reliable, experimental, property values for the commercial alloy in a commercial software package produced a significant improvement in the prediction of casting defects. Thus reliable property data are required for liquid metals but also for (i) liquid slags since many processes involve the use of a slag to refine and protect the metal or to lubricate the mould and (ii) refractories, sand and investment moulds."

Jan 1, 1999

Over the years, numerous hydrometallurgical processes have been proposed as an alternative or complement to smelters for the treatment of copper concentrates. Most of these initiatives met with limited success. Bioleaching is applied commercially for secondary copper minerals heaps and dumps, and bacterial leaching processes are being developed for copper concentrates, although industrial application is still years away. More recently developed processes usually include pressure leaching and/or ultrafine grinding. This paper proposes a new leach process to treat copper sulphide ores or concentrates: the process operates under atmospheric pressure and uses limited concentrations of ferric sulphate as oxidant; the key to the process is the regeneration of the ferric ion, which can be effected in-situ (direct process) or ex-situ (indirect process) using SO2/O2. Examples are presented for the treatment of copper concentrates by agitation leach and of copper ores by heap leaching. Application of the process to copper gold ores and chalcopyrite concentrates is also discussed.

Jan 1, 1999

By Pedro Morales

At present the Codelco´s smelter & refinery business have growing complexities, concentrates with lower copper grades, higher impurities contents, and environmental restrictions which have lead to refocus the Codelco business, not only by considering the isolated developments for each of the Codelco´s Smelt & Ref complexes, but also as an integrated corporative complex scheme which improve the economy of scale, optimize the synergies, and include new technologies for higher productivity and lower operational costs. Accordingly, for the 2008-2012 period, Codelco have prepared a Development Plan integrated to the smelters and refineries business units that improve its single potentialities of and include the advances for the Teniente Converter [1] and Continuous Converting [2] Technologies, and also include the concept of uncoupling the smelting process from the converting process allowing a higher operational flexibility, and a better control of its contaminants. Thus, processing the white metal generated in the Teniente Converter unit of the smelter A into the smelter B has comparative advantages. These changes in the business concept allow an overall increment of the smelting capacity by processing only white metal as a final product through a very marginal investment in this way the total or partial conversion of the white metal into blister copper is eliminated allowing to use the available gas capture-treating capacity, and available acid plants for increase smelting capacity as well.

Jan 1, 2006

By Jr. Brown, A. Calderara, A. L. Antozzi

"The result of extensive research into fundamental mixed metal oxide catalyst morphology has produced a next generation all titanium Dimensionally Stable Anode (DSA ®). This new DSA ® anode, patent pending, is tailored for electrowinning of non-ferrous metals (copper, nickel, cobalt, zinc) by means of this new coating technology.These DSA ® anodes are characterized by a hanger bar with vertical distributor bars, having primary titanium mesh attached by weldments. The active mesh is provided with noble-metal electrocatalytic coatings, consisting of iridium and/or ruthenium oxides, obtained by thermal decomposition of precursor solutions applied to the titanium substrates. The catalytic activity of state-of-the-art DSA ® anodes is increased by controlling the crystallite size of the noble-metals without decreasing the decomposition temperature. It is known that below a certain value (typically 400°C) the stability of these oxides, and associated lifetime, is seriously compromised. A highly active DSA ® anode, consisting of a quasi-amorphous phase, is obtained at high temperature (above 450°C), therefore not compromising lifetime performance. Through optimization of these design parameters, the manufacture of these novel anodes was identified.DSA ® anode performance advantages include: lead-free ' green' all titanium anodes, true leadfree cathode quality, energy savings of 0.3 to 0.55 V can be realized depending on the EW application when compared to industry standard lead-alloy anodes, eliminate need for cobalt sulphate addition required for lead anodes, sustainability designed into long-life recoatable anode structures, increase plant cathode output through increased current density operations, improve plant on-stream production, no sludge generated or removed, and improve current distribution producing smooth high efficiency cathode.Introduction of ProductThere are many factors to consider when engineering a high performance DSA ® electrowinning anode. Half of the anode's performance is derived from the physical attributes of the electrocatalyst and methods employed when applying this catalyst to the titanium anode structure. The other half of the performance benefits relate to the proper structural design of the anode. In this paper, we will highlight the anode development program in which De Nora has invested to provide the Electrowinning marketplace with a high performance anode product."

Jan 1, 2012

By Alex Moyano

Due to very demanding environmental rules, and to the incrementing impurities contents in the processed concentrates, Codelco Norte smelter permanently faces new demands for planning the production program with the present fulfillment of the environmental regulation. Accordingly, the CN smelter along with IM2, developed an impurity distribution simulation model, M-DICE, which predicts the impurities behavior for each of the process units of the smelter under different process configurations and concentrates quality. The development of the M-DICE included the gathering of operational data for the process units of the CN smelter, including temperature, oxygen enriched air, matte grade, etc. Then based on a mass balance for each of the process units involved in the smelter a thermodynamic evaluation was done to derive the arsenic fractional distribution among the condensed (matte/white metal/copper/slag) and gas phases. Then, the validated M-DICE was able to predict the arsenic behavior in the Teniente converter processing complex concentrates with high arsenic content, among others. At present, M-DICE is in its last stage of development, and is expected to be a suitable environmental and process management?s tool for the Codelco-Chile?s smelters.

Jan 1, 2006

By James E. Hoffmann

Oxidative pressure leaching is gradually supplanting other techniques for the decopperizing of slimes. The reasons for this include: much more rapid reactions, more compact equipment, a reduced environmental burden, and perhaps most important, a much lower final copper concentration in the decopperized slimes. This paper will discuss the reactions occurring during decopperization, the acidity and temperatures encountered and the techniques employed for discharging non condensable gasses. A spreadsheet is provided which allows adjusting the operating conditions depending upon raw (undecopperized) slimes composition, solids concentration and lixiviant composition. A typical process equipment flowsheet is provided along with a process narrative.

Jan 1, 2000

By A. Pagliero

The coulombimetric reduction method has been used as an evaluation technique for Pb-Ca-Sn anode corrosion in the LIX-SX-EW process. The proposed methodology involves three consecutive steps, i.e., cleaning, oxidation and reduction. They are carried out in the same experimental unit, in solutions containing 180 g/L H2S04 with and without the addition of cobalt. The authors have worked in a wide range of oxidation current densities, from 150 to 500 A/m2 for in a period from 0.5 to 120 hours. It can be concluded from the results that there would be a linear relationship between the applied electrical charge I*T (Coulomb) and the anode corrosion expressed as transformed Pb mass (mg), for solutions with or without the addition of cobalt. The exception is that for the last one the corrosion rate is 5 times faster, which was observed for every layer. From the evaluation of different corrosion layers, one can point out that its composition is mainly in the form of sulphate. In the presence of cobalt, about 67% of Pb would be as sulphate (PbSO4), about 27% as a basic oxide (PbO) and only 6% as oxide PbO2 on the surface. From this result, it appears that great transformations occurred in the metal/sulphate interface. Without the addition of cobalt, the proportion of oxide Pb02 on the surface increased up to 11.5%. According to the previous statement and considering that Pb was found mainly as sulphate, the authors recommend its determination be used as quality selection criterion. Its evaluation should be performed in the acid solutions with 200 ppm cobalt addition at an oxidation current density of 300 A/m2 for a period of 24 hours.

Jan 1, 1999

By Akio Ohta

The Hyuga smelter has been producing ferronickel by a rotary kiln-electric furnace process in Miyazaki, Japan. Several approaches to improve our operation have decreased the electrical energy consumption. A new process was developed to decrease the cost of energy even further. Oil and technical oxygen are injected through lances to heat up the calcined ores (calcine) instead of the electric power. Main problems during the development of the process were the short life of the water-cooled lances, the check on security of the safety system and the eruption of combustion gases through the calcine bed. These problems have now been overcome successfully, and stable operation can be maintained. The addition of 1 Litre of heavy oil per tonne of ore can save the electrical energy requirement by 8.6 kwh per tonne of ore. The new process has resulted in a reduction of the electrical energy consumption by more than 10 percent

Jan 1, 1992

By Sesha S. Srinivasan

Mechanochemical synthesis has been employed to prepare new light weight complex borohydrides, Zn(BH4)2. The thermal calorimetric and gravimetric analysis of these complex borohydrides shows the hydrogen decomposition temperature (Tdec) of about 100° C with theoretical capacity of ~8.0 wt%. This advanced materials based technology is considered to be suitable for attaining the US-DOE grand challenge technical targets. The powder x-ray diffraction analysis of the mechanically milled Zn(BH4)2 exhibits the presence of zinc borate and NaCl phase. The FTIR spectra of BH4-ion in NaBH4 has a characteristic band at 2290 cm-1,whereas in Zn(BH4)2, it occurs at ~2061 cm-1 (bridging B-H bonds) and ~2451 cm-1 (terminal B-H bonds) as well. The reversibility of hydrogen decomposition and recombination process is carried out by PCT measurements with multi-cycling procedure.

Jan 1, 2006

By I. M. Santos Moraes

Achieving high current efficiencies when operating at high current densities is a goal for every refinery, whether conventional or permanent cathode technology is employed. To obtain higher current efficiency at increased current density at Caraiba&apos;s Tankhouse, the production team decided to change the cathode cycle from eleven to thirteen days, reducing cathode cycle to one per anode cycle. The idea was to reduce the anode-cathode spacing and consequently reduce the potential for short-circuiting them. With respect to current efficiency, the overall result was not much better than that obtained with the normal operating conditions. A new attempt to obtain higher current efficiency at high current density was implemented by going back to two cathode cycles per anode cycle, this time reducing cathode life to ten days. This approach yielded the highest current efficiencies. This paper presents the data generated with the three operating conditions: normal practice, a single cathode cycle per anode cycle, and two cathode cycles per anode cycle with a reduced cathode cycle time. It compares the productivity achieved with each set of operating conditions. An analysis of the main operating parameters as well as the advantages and disadvantages involved with each condition is also presented for future reference.

Jan 1, 1999

By James M. Lockwood

"Eureka Technology has developed and patented a technology for the recycling of EAFD. Through this process all constituents of the material become salable commodities or are returned to the steel making process. In transforming the EAFD ""waste"" stream into a ""process"" stream the Steelmaker eliminates potential liabilities and the uncertain future of current processes while further reinforcing its role as a recycler. This is a cost-effective and energy efficient technology that combines hydrometallurgic and electrolytic processes resulting in the recovery of salable metals. For instance, unlike pyrometallurgic processes, zinc is recovered in metallic form and no elements are volatilized. This on-site operation also eliminates expensive transportation costs. In summary this technology reduces the cost of dealing with EAFD by recycling material currently being landfilled.IntroductionWorld crude steel production reached a new record level in 2007 - 1.34 billion tons of which 31% was produced by EAF steel makers [1]. This resulted in the generation of over 6 million tons of EAFD. This steel byproduct contains significant amounts of lead, cadmium and other hazardous metals. In the United States the Environmental Protection Agency (EPA) has designated EAFD a hazardous waste (EPA waste code K061). With over 50% of steel production in the US coming from EAF steel making this byproduct represents the single largest source of solid hazardous waste generated."

Jan 1, 2008

By W. Gong

Their outstanding thermal stability and high energy product make Sm(Co,Fe,Cu,Zr),-type alloys attractive for advanced applications. The near net-shape production of Sm(Co,Fe,Cu,Zr), bonded magnets make them potentially superior to any magnets made by sintering. Although pioneering work done by Shimoda et al. and other investigators provide insights on the proper compositions and process control of this alloy system, additional work is still necessary to improve our understanding of alloy behavior at various processing stages and to increase the production yield during powder processing. In this paper we report on the development of anisotropic Sm(Co,Fe,Cu,Zr), alloy powders for the bonded magnet application. Our focus is on the development of a moderate coercivity powder requiring a relatively low magnetizing field to charge the magnets to their optimum Br, Hci and BHmax. The magnetic properties are related to the evolution of the microstructure at various processing stages and the average particle size and size distribution of powders.

Jan 1, 1997

By C. D. Adams, R. T. Tuenge, C. N. King, J. A. Samuels, B. F. Espinoza, R. C. Dye, C. F. Schaus, D. C. Smith, N. M. Peachey

"Recently, doped calcium thiogallate (CaGa2S4) phosphors have been investigated for use in electroluminescent flat panel displays. The current technique used for the deposition of thin film calcium thiogallate is sputtering. Unfortunately, this requires a high temperature annealing process to provide the desired crystallinity of the phosphor. Recent efforts have focused on the possible use of metal-organic chemical vapor deposition (MOCVD) to produce the CaGa2S4 layer. The use of MOCVD provides an attractive alternative to sputtering since it does not require heating above the strain point temperatures of the glass substrates used for the display panels. To accomplish this, the deposition of both Ga2S3 and CaS is investigated as these compounds are intermediate steps in the development of the phosphor deposition. Uniform, crystalline films of both Ga2S3 and CaS were deposited and the process shows promise for successful deposition of the CaGa2S4 phosphor.IntroductionThe lack of a satisfactory blue phosphor having sufficiently high luminances at low power has hampered the development of high resolution flat panel displays. Recently, a new series of blue emitting materials have been investigated for use in thin film electroluminescent (TFEL) devices. l ,2,3 These phosphors are based on a series of alkaline earth thiogallate host materials of the form MGa2S4:RE where M can be either calcium, strontium, zinc, or barium and RE is a rare earth ion. A full-color VGA TFEL panel using CaGa2S4:Ce as the blue phosphor has recently been fabricated and tested. l This FPD provided a luminance of 10 cdlm2 at 60 Hz. The enhanced blue in this display allowed its color capabilities to approach those of the conventional CRT.The method of depositing the phosphor onto the display panels in these test devices has been sputtering. Unfortunately the phosphor as deposited does not possess the crystalline properties required for optimum luminance. The crystalline structure is achieved by subsequent annealing of the deposited material. Although this post deposition anneal provides the desired crystal structure, it occurs above the strain point temperature of ordinary glass. Consequently, the implementation of these phosphors requires the use of glasses capable of withstanding high temperatures, adding to the cost of the final display unit."

Jan 1, 1994

By Nexhmedin Lohja

The production of high-carbon ferrochromium in a submerged electric furnace based on double-level technology has some advantages compared to close-type furnaces with one tap hole. These advantages include the reduction of the specific energy consumption for the overall process, good separation of ferrochromium from slag, an effective treatment of raw materials including lean chrome ores (low percentage of Cr2O3) etc. An outline of the operation of this furnace along with the production line of briquettes from fines of chrome ore by using organic and inorganic binders, will be followed by a description of the recent work carried out to improve the energy consumption in this furnace through a pre reduction process of Cr2O3 ores by the off-gas energy recuperated from the furnace and the use of SiC in the feed. A short theoretical analysis of the new work will also be given.

Jan 1, 2006

By G.A Subagyo

The condition of slag in a pyrometallurgical reactor is vital to ensuring control of the process. A new technique based on multivariate image analysis (MIA) of digital images has been developed to provide an online measurement of important slag characteristics, such as the presence of exposed metal, the presence of solid phases, and temperature. This paper shall describe the technique and provide some results from analysis using industrial plant data.

Jan 1, 2003