Search Documents

By A. G. Merma

In this work, the electrocoagulation technique was studied in order to treat chemically stabilized concentrated oil-water emulsions. This study was mainly focused on the effects of operating parameters such as initial pH, current density, reaction time, electrode distance and inlet concentration on the separation of oil as measured by the chemical oxygen demand -1(COD) method. The synthetic emulsion was prepared from Shell - Talpa 30 oil (3g.L-1) and sodium dodecyl sulfate (1.0 g.L), having a Zeta potential around -70 mv at pH 8.7. The process was carried out in an electrocoagulation cell with a set of four parallel monopolar electrodes. This set consisted of two aluminum plate anodes and two 316L stainless steel plate cathodes. Kinetic curves showed that the electrocoagulation process exhibits three phases: (1) an initial phase, where the COD did not decrease because the solution had not reached the minimum amount of dissolved aluminum required to cause the break-up of the emulsion, (2) a reactive phase during which COD decreased due to possible agglomeration of the precipitates and (3) a steady-state phase where the COD did not change. The results showed that the period to reach the reactive phase decreased as the current density increased and the pH values decreased.

Jan 1, 2009

By Hugo Cabrera-Real

This work investigated the chemical and mineralogical properties of CaO-SiO2-CrOx-CaF2- MgO slags. Synthetic slags were prepared and the effect of the slag basicity (CaO/SiO2) and MgO contents on the stability of the mineralogical species formed was analyzed. The morphology and composition of the slags were analyzed by XRD and SEM-EDS, whilst their chemical stability was evaluated by leaching with an aqueous acetic acid solution. It was found that in slags with CaO/SiO2 = 1, the main Cr-compound was MgCr2O4 spinel, which forms octahedron crystals. Small amounts of CaCr2O4 and CaCrO4 were also observed. It was found that increasing the slag basicity from 1 to 2 the compounds MgCr2O4 and CaCr2O4 were formed together with the Cr(V)-containing compound complex Ca5(CrO4)3F which forms hexagonal crystals. The results showed that the highest chromium concentration levels in the leaching liquors corresponded to slags with CaO/SiO2 = 2, probably owing to the formation of Ca5(CrO4)3F.

Jan 1, 2010

By Youliang He

Twin-roll casting is an integrated casting and rolling process that involves the continuous solidification of a melt and the plastic deformation of the solidified metal between two rotating rolls. Computer modeling is a valuable tool to help engineers understand the metallurgical process during twin-roll casting. However, commercially available software can only model either the fluid flow/heat transfer of the melt or the plastic deformation of the solid, but not both. In this study, an object-oriented finite element program was developed to simulate the steady-state fluid flow, solidification and plastic deformation of an A7,31 magnesium alloy in a horizontal twin-roll caster. The melt, the mush zone and the solid were treated as a generalized Newtonian flow in an Eulerian reference frame and different constitutive equations were employed to describe the material behaviours. The effect of operational parameters on the solidification process was discussed based on the simulation results.

Jan 1, 2010

By L. R. Verney

A number of interrelated factors influence the economics of the sulphide smelting of copper, lead, zinc and nickel. This paper discusses these factors, mainly from a US point of view, and shows how they affect the cost of construction and operation of new and existing plants. The paper shows how metallurgical plant construction costs and the consumer price index have increased at a much faster rate than metal prices thereby making some metal mining and production operations within the USA, Canada and the EEC less profitable than operations elsewhere. This in turn inhibits new "grass roots" metallurgical developments. It is explained how retrofit of existing pyrometallurgical plants can be a more viable development than the construction of "green field" plants, especially if such retrofit improves, energy efficiencies, overall operating costs and reduces emissions of sulphur and other toxic wastes. Some aspects of metallurgical plant operation are examined, especially for copper and nickel, to show how changes in operating practices may develop in order to improve overall smelting economies, especially when developed in conjunction with objective retrofit. The paper also examines some financial aspects, especially insofar as the disparity between terms for loans offered to third world countries and the USA and the EEC are concerned and also comments upon the need, especially within the USA, for legislation to permit rapid depreciation of capital. Specific comments are made about environmental aspects, including the lack of uniformity of pollution control legislation and how environmental considerations may have some bearing of the location of future smelting operations.

Jan 1, 1983

By Y. F. Liang

Fe-6.5wt.%Si alloy has excellent soft magnetic properties compared with conventional silicon steel. It is very brittle at room temperature due to appearance of ordered phases, like B2 and DO3. In this paper, we investigate the effect of ordering on cold workability of this alloy. Methods of rapid quenching and hot rolling were utilized. It is found that rapid quenching and proper heat treatment of the hot rolled sheet could decrease the degree of order due to the very high solidification rate and high cooling rate. The rapid quenched sheet and hot rolled sheet after proper heat treatment could be cold rolled without crack. Microstructure, phase ordering, micro hardness, and cold rolling properties were investigated by Optical Microscope, X-ray Diffraction, Micro Hardness Indenter and Four-high Mill.

Jan 1, 2009

By Aline Maria dos Santos Teixeira

Serpentinite is an ultra basic and metamorphic rock consisting mainly of magnesium, calcium and silicon oxides. The rock under study is a host rock of chromite mine located in Andorinha, BA. The objective of this paper is to evaluate the rock's physical and chemical characteristics to be used as an additional fertilizer of acid soils. After comminution, rock samples were submitted to chemical analysis, XRD, SEM-EDS and TGA. Afterwards, particle size distribution was determined. Result analysis confirms that our rock consists mainly of dolomite, calcite and diopside. According to the result obtained, it can be said that the serpentinite rock has promising applications in agriculture for the correction and additional fertilization of acid soils. However, it is necessary to study the characteristics of the rock such as its dangers and toxicity as well as evaluate them according to the legislation for corrective acidity.

Jan 1, 2010

By Yushiro Hirai

Saganoseki smelter & refinery had operated two flash smelting furnaces from 1973, attaining 330,000 mtpy of copper production in 1989. In 1996, however, it carried out a "integration of two flash furnaces". That is, it doubled the feeding capacity to one flash furnace to shut down another furnace while maintaining the same production. Single flash furnace operation has successfully started in March 1996 accomplishing a great reduction of the total production cost. The production had reached to 350,000 mtpy in 1997, and further increased to 450,000 mtpy by executing the expansion program with single flash furnace in 1998. This paper introduces results of the single flash furnace operation and describes about an outline of the expansion.

Jan 1, 1999

By D. Death

The Tapping Camera Prototype (TCP) is an instrument being developed to record and analyse video of the molten metal stream entering a tapping crucible as it is tapped from an aluminium reduction cell. The development aims to provide potroom floor operators with continuous real time vision of the tapping process and provide an alert in the event of excessive bath contamination in the extracted metal stream. Longer term the system may provide sufficient data to enable control of the tapping process. The TCP mounts a wireless camera and periscope to view the molten metal stream via a peephole in the tapping crucible. Real time video is recorded to either digital video tape or computer disk for subsequent video analysis to quantify the bath material drawn into the tapping crucible with the molten aluminium. The images transmitted by the camera are available on a handheld LCD video screen. This work is an initiative of the CSIRO?s Light Metals Flagship.

Jan 1, 2006

By D. C. Lynch

While a sizable amount of data exist as to the activity and distribution of minor elements between matte and metal, there has been no unifying theory presented delineating the form of dissolution of these elements in molten sulfides. In order to alleviate that deficiency the literature concerning the behavior of As, Sb, Bi and Pb in mattes is reviewed. Models present in the literature, regarding the thermochemical behavior of minor elements, are tested, and new models are presented and evaluated using thermodynamic theory. The results of those analyses are used to predict optimum conditions for the volatilization of minor elements. The dearth of data on the behavior of minor elements in nickel mattes requires that this review focus on copper- iron mattes. An effort is made, however, to utilize basic knowledge regarding nickel sulfides and the interaction of nickel with the minor elements to predict the behavior of those elements in nickel-copper and nickel-iron mattes.

Jan 1, 1993

By Helvio Pessanha Guimarães Santafé Jr.

The coir fiber extracted from the husk of the coconut has been extensively used as polymer composite reinforcement in a variety of industrial applications ranging from civil construction to automobile seat cushions. The hydrophilic coir fiber does not act as an effective reinforcement owing to its low interfacial strength with hydrophobic polymers. As a consequence, coir fiber composites display relatively low mechanical strength. The objective of this work was to investigate the effect of an acetylation treatment of the coir fiber surface on the mechanical behavior of epoxy composites with amounts of fibers up to 30% in volume. Coir fibers were immersed in an acid solution of acetic anhydride for one hour, washed and dried, before mixing with DGEBA/TETA epoxy to fabricate the composites. Flexural mechanical properties were obtained by bend tests. The results showed significant differences to similar composites with alkali treated coir fibers that have been previously investigated.

Jan 1, 2010

By F. Kavicka

An original application of ANSYS simulated the forming of the temperature field of a massive casting from ductile cast-iron during the application various methods of its cooling using chills. The numerical model managed to optimize more than one method of cooling but, in addition to that, provided serious results for the successive model of structural and chemical heterogeneity, and so it also contributes to influencing the pouring structure. The file containing the acquired results from both models brings new and, simultaneously, remarkable findings of causal relationships between the structural and chemical heterogeneity and the local solidification time in any point of the casting. The determined relations therefore enable the prediction of the face density of the spheroids of graphite in dependence on the local solidification time. The calculated temperature field of 500x500x1000 mm casting of ductile cast-iron with various methods of cooling has successfully been compared with temperatures obtained experimentally. Acknowledgments. This analysis was conducted using a program devised within the framework of the GA CR projects (No.106/04/1334, No. 106/04/1006 and No. 106/04/094), of the COSTAPOMAT-OC526.10, MPO/FI-IM/021, EUREKA No.2716 COOP and KONTAKT 14/ 2005/06.

Jan 1, 2006

By Jilai Xue

Industrial wastes containing 30-50 wt.% Al2O3 and 40-60 wt.% SiO2 may serve as an alternative resource for producing Al-Si alloys. Various raw materials such as used refractory materials from metallurgical furnaces, coal fly ash, andalusite residues, and so on were tested in laboratory to produce Al-Si alloys using carbon-thermal reduction process. A mixture of anthracite and petroleum coke was used as reducing agent. One of the most important operations was to prepare the briquettes made of different raw materials with varying contents of Al2O3 and SiO2. The effects of briquette property, A/S ratio (mass ratio of Al2O3 and SiO2), the amount of carbon reducing agent, on the reduction process and the resulting metals were investigated. The results are useful for development of an alternative technology for Al-Si alloy production, which has the potential application in recycling metals from industrial wastes containing Al2O3 and SiO2.

Jan 1, 2010

By T. T. Chen

Copper anodes generated from copper scrap are relatively rich in Sn, Zn and Fe. Because of the presence of oxygen, only trace amounts of Sn occur in solid solution in the copper crystals. Thus, Sn occurs mainly as SnO2, Cu-Sn-Ni oxide and Sn-Ni-Zn oxide in the copper anodes, and Zn and Fe occur mainly as minor constituents in the Sn-Ni-Zn oxide and Cu-Sn-Ni oxide. During electrorefining, these oxide species are liberated from the copper anodes and report directly to the anode slimes. The trace amounts of Sn present in solid solution in the copper crystals dissolve but reprecipitate as Sn arsenate or a Sb-As-Sn-O phase. Accordingly, high Sn contents in copper anodes do not lead to elevated Sn concentrations in the electrolyte.

Jan 1, 2010

By Ailton da Silva Ferreira

Thermoset polymers, like the polyester, become harder with increasing temperature owing to molecular crosslink formation, which is a thermal benefit for composite matrix applications. Natural lignocellulosic fibers, however, have low thermal resistance and tend to degrade with increasing temperature. Therefore, the combination of a lignocellulosic fiber, as reinforcement, with a thermoset polymer, as the matrix, results in a composite material with complex thermal behavior. In the present work, a thermal analysis was conducted on polyester composites with different amounts of curaua fibers. Both TGA and DTG curves were analyzed to determine the effect of the curaua fiber on the thermal resistance of the composites. It was found that the curaua fiber sensibly affects the thermal behavior of the polyester matrix for fiber amounts above 10% in volume. This effect is associated with an increase in thermal degradation.

Jan 1, 2010

By G. L. Liu

"Deformation Banding ( DB ) in cold rolled mild steel has been experimentally established by microstructure investigation. Deformation banding model includes such deformation mode when it is applied to rolling texture simulation. The cause for the occurrence of deformation banding is the reduction of the total work for plastic deformation through a relaxation of the deformation constraints. In the first DB model, all grains are assumed to band from the first deformation step. Such an unrealistic assumption has been eliminated in the new model by the introduction of a banding criterion based on an energy minimizing approach. The prediction is closer to the measured texture by applying banding criterion and setting critical resolved shear stresses (CRSS) ratio for { 110 } and { 112 } slip modes to 0.85.IntroductionBased on the continuum theory of plastic flow and deformation mechanism of crystallographic dislocation slip, Taylor's FC ( Full Constrain ) theory [1] has been widely used in texture modeling. As the process of cold rolling of sheet materials produces a microstructure consisting of elongated or equiaxed flat grain or cell, the ""lath"" and ""pancake"" relaxed constraints ( RC ) models [2, 3] were introduced as the successful improvements over the classical FC model. It has been also recognized that crystals may split into different orientations during deformation and the term deformation banding is used to describe such deformation processes [4, 5]. Lee et al. [6, 7] pointed out that the success of the RC theory in predicting textures depends on the physical processes of deformation banding. They developed so called Deformation Banding ( DB ) model by considering DB in the longitudinal plane to be accounted for by the RC method and allowing DB in the rolling plane. DB model was applied to simulate the texture development in bee case [8], the predicted bee rolling textures are in reasonable agreement with the measured textures. In the first DB model, however, all grains are assumed to band right upon the first deformation step. A banding criterion was formulated [7] which states that DB will occur if the work used in DB model is less than that in RC model. Such criterion has been incorporated into the original DB model for texture simulation and is referred to as DBC ( Deformation Banding Criterion ) model."

Jan 1, 1998

By Art Cooper

Granulation systems are common in the metals industry. The process of granulating slags, mattes and metals is more than a century old, and a number of different systems have been developed to accomplish this task. These systems have followed an evolutionary path, and may be characterized by common elements in terms of molten material handling, granulation methods and post-granulation processing. This paper will summarize the more common systems used in the metals industry, with particular reference to non-ferrous applications.

Jan 1, 2006

By Igor Zh. Bunin

A model for developing electric discharges between sulfide mineral (pyrite) particles under high-voltage nanosecond pulses in a liquid medium (water) is considered. A possibility of electrical breakdowns of liquid gaps between particles under nanosecond pulses is shown. This probability and the energy released in discharge channels depend strongly on the sulfide conductivity.

Jan 1, 2010

By Han Yi

The coarse indium ingots produced by Shaoguan smelter contained a lot of impurities. In order to produce the high pure indium with the purity more than 99.99%, the appropriate refining processes were designed and the practice of combined application of Glycerin-KI process and electrolysis in Shaoguan smelter was introduced.

Jan 1, 2005

By Theo Lehner

"The Boliden Rönnskär Smelter operates in the European Context of tight EH&S limits, with ever increasing regulations and tribulations. The near future promises to bring new burdens in the form of C02 trading, miners and pre-treaters increased appetite for a larger share of contained values, and changing compositions and competition in raw materials. On the other hand, European Smelters such as Rönnskär, Harjavalta have demonstrated an astonishing power of survival. This presentation lists and comments on current challenges but opportunities for increased survival power are also presented. One example of the latter is the ongoing investment into increased treatment capacity for e-scrap.UPDATE ON RÖNNSKÄR OPERATIONSThe Rönnskär Smelter has achieved 80 years of age with no signs of retirement. The smelter is most active in spite of its age! And it has undergone some face lift operations to maintain its attractiveness.Raw material, processing facilities and a market for the products are some essential prerequisites for a viable operation. To justify long term survival, economic terms such as return on investments and positive cash flow need to be considered. Below, we illustrate how the Rönnskär Smelter complies with these terms. To update the reader on current operations, our current flow sheet is depicted in Figure 1. The figure summarizes our current input and output."

Jan 1, 2012

By Qingsheng Liu

A new method of recycling aluminum dross for preparation Al-Si-Ti alloy was studied in this paper. This was carried out in two processes. first the aluminum doss was pretreated by leaching and calcining process, the fine purity and phase of the intermediate oxide powder up to electrolysis demands, then, could be obtained when aluminum dross after washing have been leached for 2h at 100? in 20% hydrochloric acid and calcined for 2h at 1200?, which was treated by cryoite-based molten salt electrolysis. Finally, the Al-Si-Ti alloy was successfully obtained through electrochemical co-deposition in the cathode shows a typical as-cast microstructure. This new recycling method can produce high quality alloy and may bring remarkable economic and social benefits.

Jan 1, 2010