Search Documents

By C. P. Mangelsdorf

The success of the Birmingham roof truss (Figure 1) in supporting some difficult roof conditions, particularly in the Illinois coal basin, has given impetus to the development of a number of alternate schemes. These schemes attempt to alleviate two major problems with the Birming-ham truss, namely, the time required for installation and the cost of material. Because of the difficulty of drilling angled holes and the number of different pieces of hardware which must be handled manually, most operators have been unable to install Birmingham trusses in the cycle and have had to schedule truss crews during the maintenance shift or whenever they would not impede production. Due to this delay the truss has traditionally been viewed as a supplemental form of roof support. In fact, the truss might qualify as primary support and replace at least two bolts if it could he installed in the cycle (and MSHA would accept it as an alternate in the roof plan.) [ ] Figure 1. The Birmingham truss. Two attempts to deal with the first difficulty have sought to streamline the truss hardware while preserving the essential character of the Birmingham truss. One of these, by Peabody Coal, is reported elsewhere in these proceedings by C. Bollier. Another is a contract issued by the Bureau of Mines to Bendix Corporation for the development of a machine, particularly suited for use in low coal, which will automate many of the operations currently executed manually. This machine is expected to be ready for field testing by fall of 1982. Once in place, a truss installed by either of these schemes will interact with the roof in the same way as a conventional Birmingham truss. An alternate approach has been proposed by several different manufacturers independently. Although the hardware details differ. the essential idea consists of two angle bolts, the heads of which are connected by a horizontal chord tightened to some pre-determined tension. Figure 2 shows the generalized concept and does not depict any one of the four systems proposed. The advantage of this scheme is that the angle bolts can be installed and tightened in the cycle, and as bolts, immediately satisfy the roof control plan. The horizontal chord can be added later to achieve almost any initial desired roof loading, the limits of which are defined below this scheme is referred to here as the angle-bolt truss. Because of a fundamental difference in the way in which load is transferred between chords, this design does not interact with the roof under subsequent loading in the same manner as a Birmingham truss. The purpose of this paper is to examine this fundamental difference and its consequences. [ ]

Jan 1, 1982

By R. Fritschen

In order to investigate locations, source parameters, and source mechanisms of mining induced seismic events, a local network of seismic stations was installed at a coal mine in the eastern part of the Ruhr District (Germany). The recorded events were located with the help of an anisotropic velocity model, which accounts for the fine layering of the carboniferous strata. Most of the events took place about 50 m above the working Luise 76-10. Their locations correlated with the advancing working face, and the number of events increased when pillar edges were undercut. The source mechanism, i.e., the orientation of the fracture plane and the direction of displacement on this plane, could be determined for several seismic events. The majority of them was characterized by a fracture plane parallel to the working face and an almost vertical dislocation on this plane towards the goaf a mechanism resembling the breaking down of the hanging wall. The fracture plane had a dimension of about 100 m. Probably the fracturing of a sandstone layer, located approximately 40 m above seam Luise, was responsible for the observed seismicity

Jan 1, 1999

By Jeffrey Johnson

To measure the loading behavior of friction bolts, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) installed strain gauges on the interior of friction bolts and developed a battery-powered miniature data acquisition system (MIDAS) that fits inside the hollow portion of the friction bolt. The advantages of this system are that it is protected from face blasts and eliminates the need for external wiring. Laboratory pull-out tests showed that friction bolts installed in a concrete block with resin were loaded to about 1.8 tons/ft of bolt length; bolts installed without resin were loaded to 1.3 tons/ft. Three strain-gauged friction bolts were installed at Hecla Mining Company's Gold Hunter Mine, Mullan, ID, in the wall or rib of a mechanized cut-and-fill stope. The object of these tests was to establish an installation procedure for the bolt-and¬MIDAS combination and to evaluate performance. The stope was advanced in three 15-ft increments and strains induced in the rock bolts by stress changes in the rock were recorded every 30 minutes. The MIDAS proved to be rugged enough to withstand the shock and vibration from nearby (5 ft) face blasting. Data from MIDAS showed that the friction bolt installed with resin was the most sensitive to each face advance. It showed a steady increase in loading to a maximum value of 1000 microstrain. The friction bolt installed without resin showed stick-slip behavior with loads to a maximum of 400 microstrain before the stope was completed.

Jan 1, 2003

By Victor V. Nazimko

Longwall mining technology without interpanel pillars is feasible from a geomechanical point of view. A set of pillarless longwall layouts are proposed including tailentry pillar recovery, headentry pillar recovery and drivage of a new tailentry, partial headentry pillar recovery and combination mining in which advancing panel entries are used for retreating panels. The following mitigative measures are proposed in order to enhance the stability of entries near the panel: driving crosscuts obliquely to the longwall face line, advance support of entries and crosscuts, localized destressing of the chain pillars by horizontal slotting, and partial stowing of the gobs behind the pillars being recovered. A new technology of recovering barrier pillars on the setup entry side is also proposed. This technology uses the same regular longwall face for interpanel pillars extraction.

Jan 1, 1994

By D. L. Price

This paper presents a method of measuring field power consumption of shearers and deriving specific energy consumption versus shearer haulage speed performance curves. A description of a computer program which simulates the cutting action of a shearer drum is presented. A comparison between the field specific energy curves and the computer simulation results is made. The simulation results compare well with the field data where all the coal seam is being cut by the shearer. The computer simulation results give hack-calculated field pick force cutting characteristics, which allow the performance of the shearer to be predicted for other operating conditions, e.g. effect of changes to pick lacing, effect of changing the drum rotational speed, allows the calculation of power requirements for a particular production rate.

Jan 1, 1992

By Gheorghe Oncioiu

The phenomena developed on the influence of thick coal seam no.3 mining, by horizontal slices and rocks caving roof control, in the Jiu Valley coal basin, are very complex. By analyzing the influence volume of underground faces and defining the stress and strain zones, around the faces, it is possible to evaluate the suitable powered support performances. Also, Jiu Valley thick coal seams involve about 50% of reserve balance in the main safety pillars of social, industrial and natural objectives, situated on the mining surface perimeters. For a correct design and drawing of main safety pillars complex research was done with the aim of establishing the subsidence parameters. Upper face rocks medium could be assimilated as a granular medium, which is in a permanent movement. For describing the rocks movement, respectively the ground surface displacement, was taken into account the stochastic mechanics principles. The theoretical solutions are in accordance within situ measurements.

Jan 1, 1999

By Richard C. Repsher

The U.S. Bureau of Mines has developed a method and device designed to detect lose rock material in underground mines. The technology is designed to be an aid to mine workers in detecting hazardous roof conditions in underground mines which can complement or replace the traditional roof sounding techniques where the miner relies on experience to determine whether rock conditions are sound. The leading cause of accidents and fatalities in underground mines is falls of lose rock pieces or rock slabs from the mine roof. The device is an electronic roof sounding device that acoustically determines the integrity of mine rock. In previous research the Bureau of Mines found that loose rock, when impacted, vibrates at a much lower frequency than intact rock material. A major problem in determining rock stability using this technique has been the repeatability of the matt signal. This difficulty baa been greatly reduced in the current design by measuring the power spectra contained in two separate frequency bands of the signal produced by striking the rock in question. The ratio of the energy contained in each band is computed. This process minimizes any striking force differences, producing accurate, repeatable results for solid rock as well as loose, drummy material. The prototype has been successfully- tested in a variety of underground environments including coal, uranium, molybdenum, silver and salt. The technology has been investigated by the U.S. Mine Health and Safety Administration and the Department of Energy for use in detecting detached tunnel lining areas in nuclear repositories. The paper will discuss the technique, applicable results, and future applications.

Jan 1, 1990

By H. Gene Wilson

Mobile Roof Supports (MRS) look similar to a longwall shield on crawler tracks. The MRS units offer a safe, productive method of extracting the 40% to 60% product left normally unrecovered in room and pillar mining. The units feature radio control, self-contained power units, crawler track drive, and a 600 ton yield. Cribbing and setting posts in retreat mining has been a necessary burden to production. The MRS reduces this burden. Long blocks of coal can be developed to further reduce move and tram time, thus increasing production. The MRS units have successful safety records. The workers are removed from the immediate fall area, and we feel back injuries have been reduced by the workers not setting posts. While MRS units have been damaged in falls, the other capital equipment has been unharmed. The MRS product line has undergone normal product improvement and evolution. Product evolution is seen in our development of machines for particular mine requirements. Through the continuing development of the MRS, Fletcher presents the coal industry with a safe, productive method of retreat mining with potential to develop new mining methods.

Jan 1, 1990

By J. L. Condon

The Bureau of Mines, through in-house and contract research, monitored mountain bump-prone areas of the Olga #2 Mine, near Welch, WV, using microseismic techniques for 15 months during 1985 and 1986. During this period, two ground failures occurred that were considered "mountain bumps" owing to excessive stress buildups. One failure damaged the roof and 4 pillars around an intersection; the second failure, which released much greater energy, resulted in significant damage to over 100 coal pillars. Analysis of the microseismic data collected provided significant insights into the magnitude and location of each failure. The actual failure zone was clearly delineated prior to the mountain bump occurrences through analysis of source locations of each microseismicevent. Trends in cumulative rate plots indicated the onset of structural instability. Although the data could not be analyzed automatically, the significance of the data interpretation cannot be overemphasized. Microseismic monitoring of bump-prone areas can be successful in providing a means to actually observe the structural stability occurring in underground coal mines. This paper discusses data collection techniques, analysis methods, and implications of the monitoring technique, with special emphasis on actual data from two large mountain bumps in West Virginia.

Jan 1, 1987

By Bruce K. Hebblewhite

Tower Colliery is a longwall mine operated by BHP Coal Illawarra Collieries, Southwest of Sydney, Australia It mines the Bulli Seam at a depth of approximately 450m. The surface topography overlying the mine consists of several steep-sided river gorges, up to 68m in depth, which run at oblique angles across a sloping terrain Apart from some light rural development, the surface land is essentially natural bushland, but is traversed by a major freeway. This crosses one of the gorges on twin, six-span, box-girder bridges, with bridge piers up to 55m in height. Consequently, a major surface subsidence monitoring program has been in place for several years now, including intensive conventional, GPS and E DM surveying, plus real-time monitoring of critical components of the bridge structure. Although the bridge and freeway are outside the conventional angle of draw' subsidence influence criteria, and have seen only negligible vertical deformation as a result of mining, there has been widespread evidence of regional horizontal deformation of the land surface, large distances away from the mining area The effect at the bridge has been well within acceptable tolerances, primarily because of the regional nature of the movements, with very little differential movement observed at the bridge piers Gorge closure and evidence of large headlands of land moving `en masse' have been observed. Horizontal movements of hundreds of millimetres have been recorded in some locations where gorge closure has been monitored. Possible explanations of these movements include one or a combination of mechanisms such as pre-mining stress relaxation. valley notch effects, valley bulging, regional joint patterns, movement toward active goaf areas, vertical gorge shearing' and shear failure of horizontal bedding planes below the surface This paper presents a case study of the regional horizontal ?subsidence displacements? measured during mining. and a discussion of the possible explanations for these phenomena

Jan 1, 2000

By Dennis R. Dolinar

Roof falls, even of supported roof, still constitute a major hazard in underground mines. However, associated with any fall or instability is a pattern of roof movement. Therefore, the National Institute for Occupational Safety and Health, Pittsburgh Research Center, has been conducting research into the development of practical extensometer systems that can be used to measure this displacement and to determine if a roof fall may occur, thus increasing miner safety. For extensometers to be used in the detection of potential roof falls in coal mines, an understanding of the movement and displacement rates that will lead to roof failure is required. Because roof falls are unpredictable, it is often very difficult to obtain this information. Therefore, in a coal mine in the lower Kittanning seam in Pennsylvania, a room widening experiment was conducted to intentionally cause a roof fall while roof movement data was collected. In this experiment, two adjacent rooms 5.5 m (18 ft) wide supported with 1.5 m (5 ft) resin-grouted bolts and instrumented with extensometers were widened to 9 m (30 ft). In one of the rooms, 3.6 m (12 ft) cable bolts were installed as supplemental support. In the room with no additional support, a roof fall occurred 72 h after the room was widened. Much of the 3 cm (1.2 in) of movement in this room resulted from the instantaneous and transient response to mining with displacement rates up to 7.6 cm/d (3 in/d) being measured. This was followed by a steady state displacement phase with a rate of 0.43 cm/d (0.17 in/d). Just 12 h before the fall, movement deeper in the roof caused the rate to accelerate to 1.1 cm/d (0.44 in/d). The roof in the room with the supplemental cable support did not fall even though the total roof deformation was over 7.6 cm (3 in). Significant roof movements and strains in the cabled room were detected to a depth of 3 m (10 ft) while maximum cable loads were over 180 kN (40,000 lbf). Essentially, the roof was in postfailure with the cables maintaining the material, while roof stability was indicated by a steady state displacement rate of only 0.025 cm/d (0.01 in/d) at the end of the test.

Jan 1, 1997

By Gregory Hendon

Jim Walter Resources, Inc. (JWR), has successfully longwall mined for many years at depths ranging from 1200'-2500'. However, full pillar extraction has proven difficult and generally economically unfeasible. Overburden and redistributed stresses at these depths require relatively large pillars, which become unmanageable with most pillar extraction practices. The economic benefits of taking gateroad pillars as part of a longwall face have been recognized for some time, including increased life of mine recovery, elimination of belt moves, reduced overcast requirements, and improved longwall to continuous miner ratios. Until recently, the associated risks of pulling pillars prevented any extensive use of this concept at JWR. Due to geological, economic, and longwall repeatability problems, JWR accepted the risks, and undertook pillar extractions with longwall faces in several different applications. The applications included taking a stable pillar (250' wide) as a longwall panel, taking yield pillars on the headgate and tailgate of panels, taking yield pillars and stable pillars in the middle of a panel, mining through chain pillars in the middle of a panel, and taking a support pillar on the tailgate end of a panel. This paper describes the background and experience of pillar extraction with longwalls at JWR.

Jan 1, 1998

By Clarence O. Babcock

Since Vicat in 1833, the width to height ratio of a mine pillar has been taken as the fundamental variable in pillar design. From work in the laboratory by many investigators testing rock, Coal and concrete samples, it has been concluded by some that pillars with a width to height ratio of 10 to 1 are indestructible. It has also been concluded that a constrained core exists within the pillar which increases the pillar strength. The role of the roof and floor, if mentioned at all, is often noted in an incidental way. In the present work on laboratory testing of model pillars on concrete, coal, and rock instrumented with special strain gages, it was concluded that the end constraint and not the width to height ratio is the significant variable in determining the pillar strength. In tests where the end constraint is steel, a large compressive stress is produced on the horizontal plane of the pillar, and this effect increases as the width to height ratio is increased, resulting in an increase in pillar strength. If the end constraint is not steel but something with a small Young's modulus, the state of stress in the horizontal plane may be tensile, increasing as the width to height ratio increases, resulting in a decrease in pillar strength. Related to mining, the results are that a large width to height ratio pillar is strong for strong roof and floor and weak for weak roof and floor. That is, the roof and floor and not the width to height ratio determine the pillar strength. The confined core condition should be verified by testing if large pillars are to be used. If there is no confined core or the pillar is in tension, smaller pillar sizes should be used. The final conclusion is that the geometry alone is meaningless in pillar design.

Jan 1, 1984

By Bob Thomas

The roof drill operator productivity can be enhanced by the introduction of control technology The operators control station can be improved by considering human factors such as handle forces and control location. The smaller electrical controls can be located much easier than the traditional hands on valves. The operators control can he improved by using processors with programmable subroutines that assist the operator in the decision making process. For example to increase feed rate - to slow rotation - to avoid clogged steels - etc. The overall affect is to improve drilling and bolting consistency. The control system uses a dedicated processor packaged as an intrinsically safe control station. The roof drill operator is assisted in the drilling; arid bolting by a closed loop feedback system. The processor monitors the drilling parameters such as feed force, feed rate, rotation torque, RPM, drill position, and vacuum condition Based on the drilling parameters the processor executes pre-determined condition statements intended to enhance drilling The drill operator has an active display to alert him to the real time machine status. For example if the feed were to slow or delay due to a high vacuum level the display would show "high vacuum". The dedicated processor is available on the arm feed style machines, The prototype machines used programmable logic controllers to develop the feedback relations. The ability to record drilling parameters was extremely helpful in this development project. The extended use of the recording feature will aid operators in mapping the mine roofs Interpreting the recorded drilling parameters can reveal a void in the top or hard competent drilling The prototype machines also showed the importance of vacuum monitoring This feature is extremely valuable in softer materials, The benefits of the control system range from efficient use of the consumable bolting materials to uniform operator performance.

Jan 1, 1999

By Rene Rodriguez

Sandstone paleo-channels encountered during coal mining operation can significantly slow down the advance in mining, and often completely shut-down coal mine production, with consequent extensive economic losses to the mine operator. Definition of the encountered channel usually involves intensive drilling; vertically from the surface and/or horizontally from underground vantage points. Coal operators with limited resources often resort to exploration by extending mine faces toward the channel. Both drilling and underground mining exploration are prohibitively expensive and usually provide only partial information about the location, size and shape of the sandstone channel. A low cost alternative which can also provide a more comprehensive picture of the channel is the application of Underground High Resolution Seismic Methods (UHRSM) developed and successfully tested by GECOH Exploration. UHRSM applies surface seismic reflection technology rotated as needed (usually 90 degrees) to accommodate the faces of the exposed channel, coal rib, or coal in front of the inclusion (sandstone channel, etc.). This entails placing high frequency seismic sources and geophones horizontally across these exposed faces. Refraction and reflection events from the front and back of the channel are isolated, analyzed and inverted, to calculate the channel's location and geometry. This paper presents a summary of the geophysical exploration technique and two case history examples where it was applied. In the first case, the accuracy of the technique was verified through subsequent mining. Mining is yet to commence in the second case. Both cases were applied to room-and-pillar nines where the irregular rib lines significantly extended the data processing effort. This suggests that UHRSM will find the easiest application when used along straight rib lines, but that is not a requisite to the application. The UHRSM should find ready application in longwall mining to delineate sandstone channels and other non-coal inclusions in the middle of the panels or ahead of the gate road faces.

Jan 1, 1994

By Gary R. Corbett

The federally owned Cape Breton Development Corporation (CBDC) mines approximately 2.5-3.0 Mt of coal per annum from its Phalen Colliery. As part of an ongoing process to become more commercially viable the Corporation has implemented changes in its support method, namely, the transition from traditional steel set inseam supports to roof bolts as primary support in the single entry longwall retreat drivages. During 1991 and 1992, a monitoring program was implemented by the Cape Breton Coal Research Laboratory (CBCRL) to determine the loading on support systems and ground reaction in the gateroads in front of the retreating longwall faces of the 4 East and 5 East panels at Phalen Mine. The 4 East gateroad had been supported by steel sets alone. The 5 East gateroad had been supported by steel sets as well as roof bolting and strapping of the gateroad roof. Steel sets in both gateroads were instrumented with strain gauges and load cells to record support reaction to the retreating face abutment pressure. Multipoint borehole extensometers and multipoint strain gauged roof bolts were installed in the gateroad roof to monitor strata displacement and bolt loading above the gateroad as the longwalls retreated. This paper describes the details of the instrumentation and monitoring techniques utilized during this program and discusses the results, trends and differences observed in the two differently supported access roadways. Work on future data acquisition instrumentation is also briefly described.

Jan 1, 1993

By Syd Peng

In designing a proper roof support system, one must know the features of roof geology in advance of mining. The drilling parameters obtained during normal roof bolt installation cycle can provide a large amount of information on the roof geology when properly interpreted. It is also an economic way for identifying the geological features of the roof. This research develops a method for predicting the roof geology based on the drilling parameters obtained during roof bolting operation. From the results of a series of laboratory and underground tests, feed pressure is found to be a good indicator for identifying the voids/fractures and estimating the roof rock strength. This paper describes the method for determining quantitatively the location and the size of void/fracture and estimating the roof rock strength from the drilling parameters of roof bolter.

Jan 1, 2005

By S. J. Jung

The goal of this research is to demonstrate how optimization methodology can be coupled with the finite element method for greater stability of underground mine openings. As a result of increasing mining depth and intersection of geologic discontinuities, mining environments are becoming more complex. Current design procedures are rapidly becoming inadequate. In this research, the finite element method has been coupled with optimization criteria to design more stable and safe underground openings

Jan 1, 1993

By Richard G. Burdick

The Bureau of Mines', Denver Research Center has been conducting research for the past few years on the use of resistivity methods to locate abandoned mine workings. As this work has progressed, it is apparent that in some cases, in addition to detecting the old workings; stoping, precursive to surface subsidence has also been detected. This paper describes the Automated Resistivity method and discusses sites in Colorado. Wyoming. and Illinois where the subsidence phenomenon has been observed.

Jan 1, 1982

By William D. Gallant

This paper presents the results of a joint cooperative research project between the CANMET Cape Breton Coal Research Laboratory and the Cape Breton Development Corporation to observe the subsidence profile over the stopline of 2 West panel, Phalen Mine. A novel technique was designed and Implemented to determine vertical displacements of the overlying strata from within a near horizontal borehole drilled over the 2 West panel. Restrictions on data collection techniques due to the submarine nature of the coalfield are discussed. Development and implementation of the borehole technique using a piezometer and inclinometer Is described. Performance of the instruments and profiles obtained by them are presented and compared. Recommendations for design improvements are made to Improve the efficiency of the technique.

Jan 1, 1990