Search Documents

By Monika Patrycja Polak - Micewicz

This paper presents an approach for estimating the fatigue life for the base of powered roof supports (shield) manufactured by the FAZOS roof support company. FAZOS?s powered roof supports are designed to operate on an inclined coal seam in full caving with a medium, strong roof strength. This shield support is utilized in conjunction with a shearer and face conveyor for a complete longwall mining system. To design shield support, it is essential for contractor to know the physical (hardness, toughness, etc.) and mechanical properties of material (tensile strength, Young?s modulus, etc.) used for the shield support as well as the geotechnical properties of the mine site. The fatigue strength of the shield support material depends on the mean stress, alternating stress, cycle frequency, transport dimensions, mine environment and other factors. In order to estimate the fatigue life for a powered roof support system, it is assumed in this paper that the support must keep the roof stable in the mine under variable load cycles. The approach selected in this study contains Goodman?s model (Goodman, 1899) for all blocks in the design housing which is subjected to sinusoidal load. On this basis, the degree of fatigue damage was calculated and compared to the results of experimental tests. It will be shown that there is a significant detrimental effect on the fatigue life of the base of the powered roof supports due to geometrical notches. The Ramberg-Osgood model and damage accumulation rule (Palmgren-Miner) (Miner M., 1945) were used and numerical analyses were conducted, utilizing ANSYS finite element software. These analyses play a very important role in longwall casing design. The proposed method allows assessment of the yield state and forecast of the structure cracking, taking plastic strains occurrence into account. The presented method is universal and can be applied for fatigue life estimation of other subassemblies of powered roof supports. The final portion of the paper presents results of variable amplitude loading simulations on the S355N and S690Q steel used to make powered roof supports. The results of the physical tests were compared with the results from finite element methods. The proposed approach to calculate fatigue life gives the best correlation between the experimental results and calculated values of fatigue life for the powered roof support base. Finally, the design process uses a simple approach to predict fatigue life in a short time, reducing design costs and providing longer service life for roof supports.

Jan 1, 2012

By Francis Kendorski

The mining engineering design professional has limited practical and reliable tools for planning successful room-and-pillar stone mines using readily-available and collectible information. Three techniques are in common use today: the hard rock CANMET method of Hedley and Grant, the hard rock method of Stacey and Page, and the oil shale method of Hardy and Agapito. Other methods have been proposed, such as the USBM method of Obert and Duvall, the CSIR/Penn State method of Bieniawski, and the soft rock confined core method of Abel, Wilson, and Ashwin. However, the latter have practical shortcomings when applied to room-and-pillar stone mines such as developed for construction aggregate production. Ideally, the use of multiple techniques resulting in the same acceptable and reliable answer is the goal. Recently, in several underground stone mines areas of undersized pillars were examined. These undersized pillars apparently resulted from non-adherence to a mine plan. These undersized pillars now exhibit strong evidence of incipient failure such as slabbing, opening of through-going fractures, and hour-glassing. This situation allows examination of pillar designs at a ?safety factor? of essentially one. This rare opportunity allowed the examination of the suitability and adjustment of the first three design methods discussed, resulting in greater overall confidence in the methodologies.

Jan 1, 2007

By Ian Misich

Surface subsidence resulting from "total extraction" of coal in the Collie Basin first occured in 1987 when Western Collieries Ltd trialed the Wongawilli mining method. Because very little quantitative subsidence data existed for the weak, Permian sediments, a research program was set up prior to the extraction of the first panel. The objective of the study was to be able to predict subsidence characteristics and effects prior to mining future total extraction panels. Attempts at predicting subsidence began using existing subsidence models from other coal mining regions, however, as more site information became available, it became clear that it was necessary to develop a separate, site specific predictive model for the Collie Coal Basin. Analysis of extensive field monitoring data for both surface and subsurface subsidence has produced a series of empirical models which can predict the shape of surface subsidence troughs and corresponding tills, and strains for rectangular panels and describe the sequences of ground movement from the mine root through to the ground surface. The fact that both subsurface and surface subsidence characteristics have tied in well, gives greater confidence for predictions made from these models

Jan 1, 1992

By Greg Smith

This paper documents the use of bench testing equipment developed to enhance the understanding of, and improve upon, common roof bolt support systems. Most roof bolt systems consist of components that are covered within the scope of ASTM (American Society for Testing and Materials) standards. However, ASTM does not specify testing methods or performance standards for complete roof bolt ?systems?. It only designates testing methods and minimum performance standards for roof bolt ?components?. Improved understanding and continuous improvement of these systems is essential given the enormous impact that they have on the safety and profitability of underground mining operations. Bench testing equipment has been developed that effectively measures and records multiple points of deformation in a rock bolt support system while load is being applied. With this testing capability, an improved understanding of component and system stress distribution can be obtained and devices and methods for visual load indication can be developed. This paper is formatted as case studies where testing was performed to demonstrate load versus deformation profiles and to develop system improvement products.

Jan 1, 2012

By Rudiger Baltz

The sudden failure of bodies of rock is a serious problem commonly experienced in the international mining industry. These explosive releases of energy are referred-to as ?bumps?, ?outbursts? and ?rockbursts?. Rockbursts can occur at such a rapid speed that they present a direct threat to safety in large parts of the mine workings. The build-up of excess stress within the body of rock can be attributed to different causes. In shallow workings, for example, sudden and violent failure of the roof strata can be caused by leaving insufficient pillar width when practising room-and-pillar mining. At much greater working depths, as it is the case in the German coal industry, rockbursts are generally attributable to high levels of rock pressure. This can even result in coal outbursts when driving individual roadways. More than thirty years ago the German coal industry suffered from numerous rockburst incidents which caused many deaths and serious injuries. This led directly to the establishment of the Rockburst Prevention Centre, which was created at the instigation of the mining companies and the chief mines inspectorate. The consistent logging and analysis of all rockburst incidents has led to the development of a system that is still used as a basis for preventing underground rockbursts and minimising the risk of such phenomena occurring. Working closely with the mining authorities and mining companies the accredited experts of the Rockburst Prevention Centre have played a key role in helping to develop and implement a range of methods for the early detection and prevention of rockbursts.

Jan 1, 2008

By Timothy Barton

The uniaxial compressive strength (UCS) is the most fundamental measurement used in geotechnical rock characterization for mine design. While there are standardized procedures for how to conduct UCS tests, there are no firm guidelines as to when to conduct them. However, it is well known that the strengths of at least some rocks can change during the time between when the core first comes up out of the hole and when it is prepared and tested in the lab. The goal of this NIOSH (National Institute for Occupational Safety and Health) study was to evaluate UCS changes occurring in a broad range of weak coal measure rocks over a one-year time span. The study found the highest moisture contents were measured when the core was fresh, immediately after it was taken from the hole. The specimens then dried rapidly over the next few weeks. Subsequently, sample moisture contents decreased slightly in the winter and increased in the summer in response to the ambient changes in humidity. The measured UCS of the core also changed during the year, apparently in response to changes in the moisture content. The UCS values from the dry, winter months were, on average, 60% higher than the values obtained when the core was fresh, and the summer UCS was approximately 11% lower than the winter UCS. These findings have implications for the use of UCS as an input parameter for both empirical and numerical mine design methods. UCS values of unprotected core tested weeks to months after drilling can be significantly stronger and indicate stronger roof sequences than warranted. In order to obtain the most representative and reliable UCS value, it is necessary to test the core, or wrap and seal it, at the drill site shortly after recovery.

Jan 1, 2008

By Yi Luo

In the study of the topographical effects on surface movement due to underground longwall mining, the factors that affect the incremental horizontal displacements are identified using 10 collected cases. Based on this study, the angle of surface natural slope is the major contributor to the incremental horizontal displacement while the total movement is also playing an important role in some cases.

Jan 1, 1996

By Kot Unrug

Mine seals are necessary in nearly every mine to isolate mined-out areas from the ventilation network. There is a large number of seals in active mines and that number continually increases as the development spreads across the reserves. The recent accident caused by the failure of seals in the Sago mine resulted in new regulations. These regulations have been set based on a principle of eliminating the risk of failure, rather than the sound engineering and understanding of the conditions that may cause seal failure during an explosion of methane in sealed areas of the mine including the probability of such occurrences. This paper discusses the following subjects related to mine seals: The potential causes of methane explosions and the dynamic effects of pressure wave propagation. Seal materials and methods of construction in view of the interaction of the seal with the host rock environment as well as requirements for gathering geotechnical data. The design of seal dimensions is based on loading conditions, therefore the probable ranges of such loading is reviewed. There is also discussion of possible methods for shielding of seals from pressure pulses following an explosion. Particular seal?s types are examined in reference to the conditions at the seals location. A novel design is presented that will be a low- cost solution for the sealing of mined out areas. Recommendations are given for further research leading to a rational engineering system for design of new seals in coal mines.

Jan 1, 2008

By Yi Luo

Subsidence events occurred over inactive room and pillar (R&P) mines, including abandoned mines or sealed portions of active mines, are classified as unplanned subsidence because of their timing and distribution are unpredictable. When investigating such subsidence cases, many uncertainties exist and disputes often focused on whether the observed structural damages are caused by mine subsidence or other natural or artificial causes. However, solid evidences to identify the causes are often lacking. In order to conduct a thorough and impartial investigation, good knowledge in subsidence theories and other ground control subjects and broad experience are required.

Jan 1, 2009

By Keith A. Heasley

The LaModel program has been used successfully in the United States for many years to design pillars to ensure global stability of pillar recovery operations. However, the recent Crandall Canyon Mine collapse showed that further research was required to improve the design of pillar recovery under deep cover. Toward this end, a new calibration procedure was implemented in LaModel. This calibration procedure prescribes techniques for calibrating the critical LaModel input parameters based on empirical abutment loading and pillar strength, as utilized in the time-tested ALPS and ARMPS programs. The calibration procedure is intended to help guide a novice modeler in choosing calibrated input parameters that produce a standard model that fits within the verification database. However, the rigid parameter specification incorporated in the calibration procedure also removes most of the flexibility in LaModel for specific calibration to the unique conditions at a given mine site. In this paper, a number of the LaModel input parameters are varied outside the bounds of the suggested calibration and the effects on the model results are analyzed. Ultimately, it is shown how the LaModel user might vary certain input parameters to adjust the model to site-specific conditions, while still maintaining the general accuracy and philosophy of the recommended calibration.

Jan 1, 2012

By Anil K. Ray

This paper discusses in situ studies conducted at an Illinois Basin room-and-pillar coal mine to evaluate the performances of three different types of bolts under similar geologic conditions. The bolt types considered were the fully grouted passive rebar (FGPR), the resin-assisted mechanical anchor (RMAB), and the fully grouted tension rebar (FGTR). During the evaluations, the three types of bolts were installed in a single entry covering a span of three contiguous pillars with almost identical geologic conditions. The performances of the three types of bolts were investigated by instrumentting the bolts prior to installation as primary supports on cycle. Additional data on roof behavior was collected with extensometers and shear meters placed near the instrumented bolts. Excluding some time lapse right after installation, the performance evaluation of the three bolt systems was based on the data collected for over a year. Based on this study, it was found that the axial loads measured in the different bolt types did not show any identifiable patterns under the prevailing geological conditions at the mine. Therefore, the assumption that active bolts must be superior to passive ones is not always valid. Even though the studied mine did not have any thinly laminated, weak rocks in the immediate roof, the passive bolts performed as well as the active systems.

Jan 1, 2012

By Erik Westman

Few studies have been conducted regarding the location, movement, and relative magnitude of the rear abutment of a longwall coal mine. The rear abutment, or the abutment pressure arch in the gob area, is controlled primarily by the quality of pack of the gob; the more compacted the gob is, the larger the stress would be theoretically. While there is no definitive location for the rear abutment, early studies showed that it could be located as far back in the gob as 300 m (1,000 ft). Like the location of the rear abutment, there has been little research conducted and very few answers as to the exact magnitude of the rear abutment load. Due to the fact that the rear abutment has been studied considerably less than the front or side abutment, the need for further studies is evident. From a ground control standpoint, the location and magnitude of a rear abutment could reveal information on the caving process associated with longwall mining, such as when the initial cave could be expected to occur in future panels. Besides the possible importance of the rear abutment from a ground control perspective, evidence related to the longwall rear abutment could be vital from a ventilation standpoint. The peak rear abutment location could serve as an area for harmful gases, such as methane, to accumulate because forcing air through repacked rock is more difficult than through loose rock. The objective of this study is to determine whether passive seismic tomography could image the location, movement, and relative magnitude of the rear abutment as the longwall face retreated, in addition to the forward abutment and gob. The results of a passive seismic imaging study at a western US longwall show evidence for the location, movement, and relative magnitude of a rear abutment. A clear zone of highlystressed strata is shown where the forward abutment is expected and a low-velocity, damaged zone is shown behind the face where the gob is located. These two zones retreat with the face over a three-week period. In addition, the images show a return to stress levels behind the gob that are slightly higher than overburden stress levels, which is presumably the rear abutment. This occurs at a distance behind the face that is approximately the same as the face width for this mine. We can conclude that passive seismic imaging can be used to identify the location, movement, and relative magnitude of the rear abutment of a longwall mine. This conclusion is dependent on the use of appropriate data collection and processing methods. The information provided can benefit the both ground control and ventilation engineers as they strive to improve the safety and efficiency of longwall mines. The knowledge associated with the rear abutment of a longwall could not only help increase production through proper initial planning and reduce down time, but it could also make positive strides in improving the overall safety surrounding a longwall mining operation.

Jan 1, 2012

By Dave Minney

The South African mines health and safety regulations require that mine management establish a quality management system for rock support material. Quality control of resin capsules used as a support medium in South Africa is specified under SA National Standards No 1534. Experience has shown that this specification, while addressing the chemical and physical aspects of the products, but does not address the required performance criteria. In order to address this shortcoming, the industry has put a lot of emphasis on short encapsulation pull tests, performed insitu, in the underground workings of the mine. This is also fraught with many shortcomings, particularly as regards site availability, cost and repeatability of results. To try and address these issues, the Department of Mechanical and Aeronautical Engineering at Pretoria University were approached to develop equipment and machinery that could produce reliable, repeatable results in a laboratory environment which reasonably simulates installation practice underground. The test method is based on the ASTM F432-95 Strength Index test, but modified to use push test rather than pull tests. The paper describes development of the test method and the preliminary results and findings of the work.

Jan 1, 2007

By Bill Kyslinger

In underground mining, machine design is predominantly dictated by mine conditions and individual customer desires. In partnership with Boart Longyear Poland and KGHM, J. H. Fletcher & Company was tasked to design and manufacture a single-boom, single operator drill module for installation of 1.2 meter expansion bolt in a 1.6 meter height mine. The objective was to produce a machine to provide ergonomic improvements for the operator while working in the mine environment. This dictated the requirement for a small easily controlled, maintenance friendly design with a remote operator?s control station. The selected design method was to use starter and finisher drill steels. This combination, requiring a number of mechanized machine motions, provides the ability to drill the required depth in the specified mine height. To accomplish the task from a remote location, a conscious decision was made to employ current technology in the form of small pressure compensated hydraulics and electronic controls. The result of the design method is a modular assembly with each sub-component designed to be replaceable and adjustable independently from other machine components. The low profile remote roof bolting module is made up of six major sub-components. Each major component is painted a different color to help the operator make the visual connection from the drill module to the operator?s control/display monitor. The Stabilizer (White) secures the module between the mine top and floor. The Drillhead (Orange) produces the drilling rotation and torque but also must slide out of position to allow the machine to manipulate the drill consumables. The Drill Steel Carousel (Blue) holds and indexes the starter and finisher steel from position to position. The Manipulator Arm (Green) moves and guides the drill steels and drill consumables from position to position during installation. The Roof Reference Guide (Yellow) locates the mine roof and guides the drill steels and drill consumables into position. The Linear Bolt Carousel (Purple) holds the drill consumables. The low profile remote roof bolting module allows the operator to drill and install a roof bolt manually or automatically with the push of a button. This design substantially reduces the operator?s exposure in the mine environment, as well as inherent pinch points and rotary hazards. Positioning the operator safely in the confines of the air conditioned cab.

Jan 1, 2006

By V. Bondarenko

The forecasting of floating earth inrush into the working is to a great extent connected with the investigation of the rock mass stressed-deformed state around the working. The aim of such investigations is to estimate the carrier ability of the protective layer (which is stabilized by the physico-chemical mode of fixing) and to determine it's thickness, which is to be sufficient to present the floating earth inrush into the working. We consider the protective layer to have exhausted it's carrier ability if the rocks of this layer reached the overlimit phase of deformation and it's greater part (section), which adjoins the working. is destroyed up to the limit of the remaining strength. So, the aim of investigations is to determine the size of the rocks inelastic deformation zone in the roof of the working. It is necessary to take into account the presence of water saturated seam in the roof and the overlimit characteristics of the rocks, their ability to lower the carrier capacity up to the level of the remaining strength.

Jan 1, 1996

By Francis Kendorski

The Skyline #3 Mine of Canyon Fuel Company in Utah was planning longwall mine development adjacent to and downdip of older mine workings known to be flooded. Barrier pillar geometries and widths were proposed by mining company personnel. Hydraulic conductivity testing suggested that the general characteristics of the local coal seam, dikes, and faults are only weakly conductive and that leakage through the barriers, if any, would be minor. The mechanical performance of the proposed barrier pillar design was evaluated according to (1) published empirical design methods and (2) numerical stress modeling. Comparison of the proposed design, with the range of barrier widths derived from the empirical methods, served as a first-order check on the adequacy of the proposed design. Numerical modeling was used to evaluate conditions site-specific to the Skyline #3 Mine and barrier geometry. Models were developed to quantify the relationship between barrier width and the abutment stresses onto the future workings. The models were also used to estimate the stress distribution within the barrier pillars. The hydraulic performance of the proposed barrier pillar design was evaluated according to (1) published empirical design methods for hydraulic impoundments, (2) empirical method estimates of seepage through coal barrier pillars, (3) numerical hydrogeologic flow modeling, and (4) numerical strain modeling. Using the techniques described above, and based on relevant industry experience, underground observations, knowledge of local geologic conditions, hydrogeologic measurements, and analytical results, the level of geomechanical risk associated with the barrier design as proposed was considered low and the level of hydraulic risk was considered moderate. The largest uncertainty that remained was the possibility that unfavorable geologic structures, such as faults and dikes, would act as conduits for leakage of impounded water into the new workings. Although the study indicated only minor steady-state leakage would occur through a small number of known structures, the presence and full leakage potential of threatening structures in the barrier could not be reliably known until the barrier was mined. One longwall panel has been completed adjacent to the barrier with no evidence of water flow even in fractured zones. Thus, as predicted by the modeling and analysis, it appears that abutment stresses imparted on the barrier during mining did not substantially alter the natural hydrogeologic characteristics, or leakage potential, of the barrier. The longwall coal mine water-barrier pillar design and performance are considered a success.

Jan 1, 2007

By Yi Luo

Multiple-seam mining operations induce surface subsidence basins different from those caused by mining in a single coal seam, and also disturb the mining operations in the other coal seams. A computer program, CISPM-MS (Comprehensive and Integrated Subsidence Prediction Model for Multiple Seam Mining), has been developed to predict the final surface movements and deformations as well as the interactions associated with multi-seam coal mining operations. The program applies a newly developed subsurface subsidence prediction model that is able to consider the geological stratification variations. In predicting surface subsidence, the surface movements and deformations caused by the individual mining operations as well as the interactive effects are all considered. A case study is conducted in this paper for validating the program.

Jan 1, 2012

By Collin Stewart

Bowie Resources maintains one of the most pro-active ground control programs in the U.S. mining industry today. Its guiding philosophy is that everyone in the organization, from the miners at the face all the way through the top management, are involved in ground control. Some of the unique elements of the Bowie ground control program include: ? Roof bolt operators log the stratigraphy of test holes in nearly every cut. These ?lithgraphs? are used by section foremen to determine the need for additional roof support, and they are entered into the geologic data base for use in geologic modeling and mapping. ? Underground core drilling is conducted to obtain data for CMRR and stability maps. ? Weekly ?Quality? meetings, involving mine management and technical staff, are held to ensure that ground control information is integrated into production operations. The paper will describe the program in detail, discussing the involvement of roof bolters, section foremen, surveyors, technical staff, and production managers. It will also show how the program has contributed to the mine planning process. Case histories of successful ground control interventions will be discussed.

Jan 1, 2006

By James Pile

Long, high capacity, highly tensioned, cable bolts (strand bolts), stiff enough to be installed with resin like a solid bolt, yet flexible enough to be used in any lengths, have been widely used in Australian coal mines since the early 1990?s. A brief history and update on recent developments of this technology is provided. The first major US trial of this Australian technology, has recently taken place at BHP Billiton?s San Juan longwall coal mine in New Mexico. Thirty-five foot long, high capacity, highly tensioned, post-grouted cable bolts are being used to provide active secondary support of intersections in areas where operator safety and life of mine considerations are paramount, and standing support cannot be installed for reasons of equipment access. The cable bolts are resin anchored into overlying sandstone channels, tensioned, and post-grouted. The installation procedure and support results for these highly tensioned cable bolts are given.

Jan 1, 2007

By Anthony Iannacchione

Designing coal pillars to provide resistance against overburden loads has long been an aim of rock mechanics engineers. The need for accurate pillar strength models has become more urgent as greater overburdens are encountered and pillar sizes grow larger. Current pillar design models differ widely in their predictions of the trend in pillar strength with increasing pillar width-to-height ratio. The goal of this paper is to evaluate current pillar strength theories, using a comprehensive data base of stress measurements from coal pillars. The stress measurements indicate that coal pillars maintain relatively high stresses near the ribline, and that the stress gradient within the yield zone can be approximated as a straight line. Several problems are identified for further research, including calibration procedures for different types of stress cells, strain softening behavior in the yield zone, and measurement of stresses in the cores of very wide pillars.

Jan 1, 1992