Search Documents

By W. C. Yates

Lack of visibility from cabs of the large haulage trucks used in open-pit mines has become a serious safety problem. This Anaconda research program was conducted to develop a low-cost system for alerting haulage truck operators of the presence of small vehicles in their blind areas. Several systems, developed and tested to help solve this problem, are summarized and evaluated in this paper. As the size of the haulage trucks used in large open-pit mines has increased, so have the blind areas. Mine utility vehicles, pickup tucks and cars become concealed within these blind areas and, thus, become a serious safety hazard. Figure 1 shows the typical blind areas of a 150-ton haulage truck. The areas of greatest concern are those at the rear center and front right corner of the truck. It is within these areas of "no visibility" that numerous small vehicles over the years have been crushed by the large haulage trucks at various mine sites. Although the occupants in most instances, have escaped the vehicle before it was destroyed, injuries and deaths have occurred. The accidents, in most cases, were attributed to negligence or carelessness on the part of the driver of the smaller vehicle, but the problem of limited visibility still exists, and a solution is needed.

Jan 1, 1982

By Karl Gunnar Holter, Frank Clement

"INTRODUCTION Typically waterproofing of conventionally excavated tunnels has been done by installing pre-fabricated sheet membranes between the primary temporary support lining and the secondary permanent inner lining. The membrane acts as a separation or sliding layer between the linings, which is often desirable. The geotextile installed behind the sheet membrane provides the required drainage and protection of the system. The design of the tunnel lining is strongly influenced and limited by the use of waterproofing sheet membranes. Since primary and secondary linings are separated from each other, forming a double-shell lining system. In that case the secondary lining must be designed for all permanent loads, although the sprayed concrete primary lining continues resists ground and water loads for a long time after construction. Significant progress has been made in sprayed concrete technology over the last two decades, with advanced admixtures, as well as the improved application technology using spraying robots. The development of new admixtures like superplasticizers based on poly-carboxylates, alkali free accelerators and silica fume, enables designers to use permanent sprayed concrete linings (SCL) increasingly for long-term service life. When designed and applied correctly, sprayed concrete can be considered as permanent. The use of spray applied membranes has seen increased use over the last decade in some countries, and demonstrated functionality and cost-effectiveness in several situations. This paper describes the use of the sprayed waterproofing membrane MasterSeal 345, an EVA polymer based product, and the practical experiences from several projects. SPRAY APPLIED WATERPROOFING MEMBRANES The sprayed waterproofing membrane is polymer based and has been especially developed for underground structures. The membrane is applied between primary and secondary concrete linings and develops high bond strength on both sides to the concrete (doubled-bonded)."

Jan 1, 2016

By D. R. Buist

The Taharoa plant of New Zealand Steel Mining Limited extracts a 57% Fe titano-magnetite concentrate from a large mineral sand deposit 90 miles south of Auckland on the west coast of New Zealand's North Island. The plant consists of an 18-inch suction cutter dredge which feeds a 750 TPH floating separation plant. An initial gravity/ size separation is obtained using cone concentrators. Finished concentrate is produced by a combination of conventional drum magnetic separators and top fed wet Mortsell magnetic separators. Concentrate is stockpiled by cyclone, and reclaimed by a bull- dozer and tunnel system. Repulped concentrate is pumped by sub- marine pipeline to slurry tankers anchored at a single buoy one mile offshore. Current concentrate production rate is in excess of one million metric tons per year.

Jan 1, 1973

By T. McNulty

The author was privileged to find employment as a uranium mill chemist for The Anaconda Company while working his way through school in the mid-1950s. He then served Anaconda in various technical and management positions until 1980. This paper describes the prevalent technologies employed by uranium producers, briefly describes various mines and mills in the U. S., and memorializes a few of the thousands of men and women who contributed to the U. S. Uranium Boom. Following isolation of uranium as an element by M. H. Klaproth in 1789, uses of uranium were confined primarily to pigments, glass coloring agents, and ceramic glazes. In 1896, Antoine Becquerel found that uranium is radioactive, releasing particles and energy as it decays. In 1898, Pierre and Marie Curie isolated radium from uranium and learned that it can be an effective treatment for some types of cancer. In 1939, it was discovered that the isotope U235 is fissionable1 . Up to this point, nearly all uranium production was from pitchblende concentrates made in Bohemia, Canada, and the Belgian Congo. In 1938, only about 5 percent (23.85 short tons) of global output was produced from ores of the carnotite mineral that were being mined in the U.S. By the early-1950s, physicists in many countries had begun to recognize the potential for nuclear chain reactions. Ernest Rutherford (UK), Frederick Soddy (UK), and Leo Szilard (US) explained transmutation of elements and formulated the principle of “atom splitting”. In 1934, Marie Curie’s daughter, Irène, and her husband, Frédéric Joliot, identified uranium as the most viable source for this new form of energy. The basic fission process was unraveled by German scientists in December 1938. After Hitler’s army seized the uranium deposits in Czechoslovakia, many feared that Germany would build the first nuclear weapon.

Mar 2, 2022

By William E. Robinson

Why did it fail? My first reaction when assigned this topic was to say: because somebody "goofed"--then thank you all for letting me say those few words, then promptly sit down. All of you have been bandying this problem around for many years--so all of a sudden I should come up with the solution. Well, While I might not provide you with your particular answer, I think I can show you some of the resolutions to it. Somewhere along your path of experience you may have discovered that a good formula for starting a fight is to tell a group of dedicated (Nordberg Crusher) users they should be using (Allis-Chalmers), or a group of (Allis-Chalmers) 'users they should be a (Traylor). Now, if you really want a melee, get both groups together and tell them they should be using a (Stedman Cage Mill). This is one sure way you can learn how great minds arrive at logical, well thought-out conclusions, based on all the relevant facts. Why did it fail? I could go on for hours giving you specific reasons why. One of my engineering professors used to start his new class off each year by writing on the blackboard--four and two, then turn to the class and ask: What is the problem? One brave scholar would venture to answer 8. His head would shake no. Another would dare 6. Again, a head shake. Now that the ball had gotten rolling, a number would vocally decide it had to be two, which produced only another shake of the head--no. All of them had missed the question he had asked : What is the problem? What he had gotten ,were some of the possible answers to the problem.

Jan 1, 1977

By C. D. Litton

This paper describes two new gas diagnostic techniques which have been used successfully to determine: 1) the combustion status of underground mines which have been sealed due to fire (Littol1 Ratio); and 2) the location of fires in abandoned, underground mines or waste banks (Kim Ratio). The Litton Ratio makes use of the rate of change of CO, calculated on both an air-free and methane-free basis, from mine gas samples and compares these values with those expected from a normal, combustion-free environment. The Kim Ratio uses the concentrations of total hydrocarbons, C2 ?C5, less the methane, to arrive at ratio values which increase as combustion intensity increases. The details of these two new techniques, their application to real situations, and their limitations will be discussed.

Jan 1, 1989

By William J. Dimond

Computor analysis has opened a new world of information for the mining of resources. This paper is directed at the mining of coal. The same procedures apply to most mining projects. The available facts when evaluated against the variables produce the answers. The project must be carefully analyzed, so that the facts can be organized in a data file. The file can be expanded as additional information is obtained during the entire life of the mine. If the mine is pre-planned, the file will be expanded in an orderly fashion and updated information will be available at all times. The development of a property goes through several phases; Exploration, Economic Analysis, Development, Production, and Reclamation. Each phase is an expansion of the data file. The validity of the answers is directly related to the accuracy and quantity of available data. The basis for a data file is horizontal position, and elevation of each piece of information. A coordinate system and datum are reference for a digital (X, Y and Z) position in a spatial system, a three dimensional digital model of the mine. The current practice is to use the State Plane Coordinate system and elevations as established by the U. S. Coast and Geodetic Survey. Each state has adopted this system by law. In the event there is litigation, it is an advantage to have the data on the legally recognized system. The control must be expanded so that all data can be assigned a digital position, and planned to fulfill the requirements for all phases of the mining operation. The project must be analyzed to insure that the objectives can be achieved without duplication or loss of time. sufficient data must be available to reach each required level of information. The coal data can be defined in two categories, spatial

Jan 1, 1977

By Robert H. Poppe

The Regional Copper-Nickel Study examined the potential impacts of copper-nickel sulfide mining, concentrating and smelting operations in northeastern Minnesota and gathered extensive monitoring data on the ecological characteristics of the region's aquatic and terrestrial biota. Because of the many development options possible, the diversity of the region's ecology, and the uncertainty of future environmental regulatory requirements, the Study did not attempt to measure the magnitude of environmental impacts on specific biological communities from a specific development proposal. The Study provides a broad base of environmental resource and impact information that hopefully will assist mining developers and environmental regulators when assessing specific proposals in the future. The following discussion is not a description of what will happen if copper-nickel development occurs in northeastern Minnesota but an exploration of why certain potential aspects of such development should be carefully considered and adequately understood before unnecessary or irreversible decisions are made.

Jan 1, 1980

By David Wilburn

Recycled materials are increasingly being used in road construction to supplement natural aggregate derived from crushed stone, sand, and gravel. An understanding of the amount of substitution that is taking place, its economics, and factors affecting the level of substitution is useful in estimating the potential for recycling and in assessing the total supply of aggregate. While U.S. consumption of recycled aggregates from crushed concrete is estimated to have increased 160 percent between 1994 and 1996; it comprised less than 5 percent of total aggregates consumed in 1995. Construction waste supply is regional, and is determined by infrastructure decay and replacement rates. Aggregate recycling rates are greater in urban areas where infrastructure is being replaced, natural aggregate resources are limited, disposal costs are high, or strict environmental regulations prevent disposal. Recycling is expected to increase as construction contractors attempt to save on transportation, disposal, and new material costs. Aggregate producers include recycled material as an option to consumers in order to prolong the life of their reserves and improve their range of products. Recycled aggregates can be a supplement for natural aggregates in selected applications, but their use should be evaluated locally based upon relative cost, quality, and market factors Because aggregate recycling is often affected by local and regional transportation systems, disposal and tipping fees, resource supply, the market for specific products, and municipal support, costs for three representative fixed site operations of different sizes were modeled. Under study conditions, all were found to be profitable, but highly dependent upon local tipping fees and market prices, which can differ significantly by location. Smaller operations were found to have different operational dynamics, often requiring creative marketing or incentives to maintain profitability.

Jan 1, 2001

By Victor J. Scaravilli

This report is based on experience developed on the construction of one contract for the Buffalo, New York subway. The Buffalo subway is under construction for the Niagara Frontier Transportation Authority and is called the LRRT-Light Rail Rapid Transit or more commonly the Metro. The Initial Route of the Buffalo subway construction started early in 1979 and is scheduled for completion in May, 1984. The initial system includes 5.2 miles of underground construction, 1.3 miles at grade for a total of 6.5 miles of subway system. A total of fourteen stations, eight underground and six at grade are included on the system. The Initial Route has a planned expansion to 17.3 miles in the future. On January 15, 1979, a Joint Venture of S & M Constructors, Inc., Solon, Ohio, James McHugh Construction Co., Chicago, Illinois, and Kenny Construction Company, Wheeling, Illinois, was awarded contract 100031, the Line Tunnels from Amherst Street to South Campus in northcentral Buffalo between Delaware Park and the State University, (see Fig. 1, Location Plan) This $35,000,000.00 contract was designed by Hatch Associates Consultants, Inc., Buffalo, N.Y. The Notice to Proceed was issued January 15, 1979 and the scheduled completion date is August 18, 1981. The project consists of two parallel rock tunnels with a minimum excavated diam of 18 ft 0 in. and a final concrete lining of 16 ft 0 in. diam. The tunnels total 14,630 linear ft. In addition to the tunnels, contract C-31 includes four shafts, an underground pump station, three cross passage connections, and other minor work items. (see Fig. 2, C-31 Project Plan and Profile) The tunnels were constructed primarily within the Bertie Formation, an approximately 50 foot thick moderately fractured to massive, dolo-

Jan 1, 1981

By Andrew B. Cecala, Robert J. Timko, Christopher J. Pritchard

As mine venti1ation systems become more complex, it is increasingly difficult to supply fresh air to the working face. A high percentage of the fresh air entering a mine never reaches the working face because it short circuits through stoppings and doors, exiting the mine without being utilized. When ventilation limits are reached, the only option presently available to most U.S. mines is to sink a new shaft - an extremely expensive undertaking that many companies cannot afford. Reusing or recirculating a percentage of ventilating airflow may make it possible for some mines to remain operational while maintaining a safe environment for workers. Such a study was performed at a trona mine in Granger. Wyoming. A vane axial fan was used to recirculate approximately 9.4 m /s (20,000 cfm), 25% of the total ventilating airflow, back to the working face area of a three-entry continuous miner section. This study involved two evaluations: the first when the face was 305m (1,000 ft) from the recirculation fan, the second when the face was 610m (2,000 ft) from the fan. The evaluation consisted of monitoring the mine atmosphere for respirable dust, methane (CH4). carbon monoxide (CO), and nitric oxide (NO), at various locations in the intake and return entries. Several shifts were monitored, with and without the recirculation system in operation. With the recirculation system in operation. there was an increase in measured respirable dust concentrations in the intake along with a slight increase in the mine temperature (1.67°C). There were also some minor changes in CO and NO levels in the intake entry, but this seemed to depend on the proximity of the instruments to the turn-around point for the diesel haulage vehicles, than to whether the recirculation system was or was not in use.

Jan 1, 1989

By David G. Van Hersett

The single most unique design feature of the Centralia Coal Mine is the public information program. Just what the heck does public information have to do with the development of a coal mine? The utilities of today have had to build larger and larger plants to keep down the costs of power to the consumer. The large plants require huge amounts of capital, take up large areas of real estate, consume unprecedented amounts of coal, and generate large quantities of waste products which have to be reckoned with. Coal mines supplying these plants have also increased in size and production to meet the power plants' unending appetite for coal. This means the disturbance of great areas of land and significant alterations to the landscape. Today's public is greatly concerned about the environment in which he is living. The great size of a power plant with its large stacks, coal piles, and the coal mine with its large earth movers, disturbed acreages and the resulting waste products of both operations appears to present a threat to his environment. Because of this,' many power plants and coal mines are having public acceptance problems. This has resulted in the passage of stringent legislation and in some cases brought upon construction delays for major power plants.

Jan 1, 1970

By A. D. Trujillo, R. D. Wunder

The Chino Mines Co., a Kennecott- Mitsubishi partnership, located in Hurley, NM, recently completed a $405 million modernization of its mine, concentrator, and smelter facilities. The mine/concentrator modernization commenced in 1980, and the smelter modernization began during 1982. Modernization of the mine and concentrator facilities involved increasing the mining rate from 98 kt/d (108,000 stpd) to 152.2 kt/d (167,800 stpd). Ore mining was designed to increase production from 20.2 kt/d (22,300 stpd) to 34 kt/d (37,500 stpd). A new concentrator was con- structed near the mine using semiautogenous grinding. The new smelter uses the INCO flash smelting process, increasing capacity by 40.8 kt/a (45,000 stpy) to 99.8 kt/a (110,000 stpy) of saleable copper.

Jan 1, 1988

By George Munro

New Zealand is a small, almost pristinely pure country environmentally speaking. It is blessed with an abundance of clear waterways, lush green vegetation and fresh clean air. It is a country in which agriculture and forestry predominate, and mining developments have to be introduced prepared to answer in considerable detail the question "How will this proposal affect the New Zealand environment as we know it today". Those who make the legislation have the difficult problem of establishing standards at a level which will maintain as far as possible the status quo without unduly inhibiting the developments currently approaching the starting line. We have been fortunate in some sense in that since the demise of the early gold rush days by the 1920's, little mineralisation of a complex nature has been uncovered in New Zealand. Coal fields have been developed in the central North Island, and on the West Coast and Southland regions of the South Island. A ban on large scale open cast mines in the Coromandel area has restricted mining in that highly prospective area, although three large gold prospects have got underway elsewhere in the last three years. There is no other ore processing being undertaken at present. Some recent proposals involving lead, gold and silver in complex arseno­ sulphides have failed to get the necessary approvals and have been discarded. Our ore processing problems are therefore straightforward ones, and confine themselves to acid drainage, mercury handling and disposal, and cyanide.

Jan 1, 1991

By David H. Carrillo

HYL has developed a sticking tendency test which accurately predicts behavior of iron oxide feedstocks in the HYL III process. Test results together with pilot plant experimentation and commercial scale demonstrations permit the conclusion that lump ores will not agglomerate at 960°C (1233 K) in an HYL III Plant. Pellets may also be processed without agglomeration at 960°C (1233K) with the addition of no more than 5 percent lump ore. Using the HYL III process, the ironmaker can exploit feedstock market conditions without sacrificing plant productivity or energy efficiency.

Jan 1, 1981

By B. G. Long

Coastal States Energy Company (Coastal), a wholly-owned subsidiary of The Coastal Corporation of Houston, Texas, owns coal mining operations in Utah and Kentucky. One of the Utah operations, Southern Utah Fuel Company (SUFCo), located 30 miles west of Salina, Utah, has been operated by Coastal since 1974. This operation is a single-seam, six-section mine operated from one portal area. It produces 2.2 million tons of coal per year and has a payroll of approximately 300 employees, Coal is mined by continuous miners, hauled by diesel-powered haulers and transported by belt conveyor to outside crushing and screening facilities. Sized coal is hauled by contract truckers 80 miles to a unit-train facility located at Levan, Utah.

Jan 1, 1983

By Lui Bin, Li Xinghua, Jiang Guoan

By employing decision support system and Borland C++ and Foxpro 2.58 For Windows as development means and tools, this system comprehensively applies the price decision theory, fore- casting and optimization techniques as a complete theoretical system, realizing the computerization of analysis, forecasting and decision process of coal price.

Jan 1, 1996

By Russell G. Slayback

Feasibility investigations for prospective gold mines too often neglect to consider ground water. Simple observations and tests during drilling exploration can provide useful data on probable water conditions. As the prospect becomes more serious, more detailed investigation of ground water and dewatering needs may be warranted. Ignoring ground-water conditions can lead to costly mistakes.

Jan 1, 1987

By Takayuki Sakai, Takefumi Takuma, Lee Roesner

"70-foot deep rectangular-shaped bulkheads were built with sheet piles as launching and receiving shafts for a pipe jacking operation for new underground waterlines in a densely populated section of Los Angeles, California. The Press-in Piling Method was specified to drive 95-foot long sheets (a record for the method) to form the bulkheads for the Los Angeles Department of Water and Power’s LA-29 (DWP) Connection Modification and Pipe Jacking. The piling was chosen because of its very low noise and practically vibration-free nature since the site is surrounded by houses, an apartment complex, and existing water lines. The out front areas of the bulkheads were grouted to let the TBM go through without major ground water leaks. Hydrophilic foam grout was also injected in addition to welding steel scab plates on the inside to seal them to achieve sufficient watertightness behind a few split interlocks. BACKGROUND This project was located in the Crescent Heights area of Los Angeles which is a few miles south of Beverly Hills. The project represents the completion of the last phase of the Stone Hollywood Trunk Line. This was an 8-mile long water trunk line that averaged 60 inches in diameter and was built to improve the reliability of the DWP’s major water system. This section of the project involved driving 2 deep shafts to allow for the installation of a 350-foot-long 72-inch steel casing using microtunneling construction. See Figure 1 for the shaft locations and the tunnel alignment. The challenge for the project was that this water line would have to pass beneath the Hollyhills buried box drain (15 feet high by 20 feet wide). Further complicating the construction was the soils beneath the drain. The DWP chose to drive the tunnel at a depth of approximately 65 feet to ensure that the ground conditions were uniform and suitable for the microtunneling equipment. There were two previous attempts to construct this work which failed because of poor ground conditions and very high water levels. This third attempt was critical because the DWP could not afford to have another failure due to the fallout with the residents being impacted by the project."

Jan 1, 2016

By S. Painter

The effects of forced ventilation and thermal radiation in open drifts are included in three-dimensional thermal hydrology simulations of a potential waste repository at Yucca Mountain, Nevada. A semi-analytical model is used to calculate the amount of waste heat removed by ventilation air during each time step of the multiphase thermal-hydrology simulator. The model accounts for thermal radiation and changes in air temperature and humidity along the emplacement drifts. The fraction of heat removed by ventilation is time and position dependent.

Jan 1, 2004