Search Documents

By R. C. Gilmore, S. A. Lolon, G. E. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

"Gob ventilation boreholes (GVBs) are widely used in underground coal mines for longwall gob degasification purposes. GVBs are often drilled within 10 to 30 m above the top of the coal bed into the fractured zone, completed with 20 cm (8 in.) diameter casing and 60 m of slotted pipe at the bottom. The purpose of this completion strategy is to create a pressure sink to capture the emissions before they can enter into the underground workplace. For GVBs to work effectively, they must be drilled close enough to the working areas to capture methane from the fractured zone while the setting depth must be kept above the caved zone to minimize the amount of ventilation air that is drawn into the GVBs. Well completion parameters are important for creating safe working conditions. In this paper, computational fluid dynamics (CFD) studies will be presented to analyze the effect of different practices for GVBs completion parameters for methane extraction, formation of explosive gas zones in the gob and methane concentrations at the longwall face and tailgate. Authors have identified the optimum completion parameters for GVBs, which can maximize the benefit and minimize fire and explosion risk. INTRODUCTION Coal mines may be considered gassy based on the presence of CH4. Gas from the mined coalbed or from rider seams above or below the mined coalbed can migrate into the gob and then potentially move towards the working areas. In longwall coal mines with high methane emissions, sufficient ventilation and additional methane control measures are usually required to reduce the methane concentration in working areas to below statutory levels. Several techniques or combinations of techniques are available to control the methane hazard. These may include mine face ventilation to dilute methane, coal bed degasification, nitrogen injection into the gob to render a methane atmosphere inert and the use of gob ventilation boreholes (GVBs). Longwall face ventilation and dilution alone can only handle methane emissions up to a certain amount. When methane emissions exceed the face ventilation capacity, additional control measures are required. Drilling horizontal or vertical methane drainage holes into the coal seams as well as gob ventilation boreholes from the surface into the gob area to extract methane are common practices. GVBs are usually drilled from the surface above the longwall panel ahead of mining. When the face moves outby the GVBs and the gob begins to form, methane production starts from the boreholes. It is important to control the performance of GVBs to maintain a safe working environment in the mine. The performance of GVBs depends on multiple factors, including borehole location, length and diameter of slotted casing, setting depth of casing above the coal seam being mined, wellhead vacuum pressure, and permeability of caved-fractured zones."

Jan 1, 2016

By Otis M. Clarke

The Eufaula bauxite-kaolin district in southeastern Alabama is an important source of raw material for the refractory industries in the United States. At the present time, five companies are mining and processing bauxite and kaolin from this district and a sixth company is holding substantial reserves. Mining operations are expanding, but finding new ore reserves is a major problem. The Geological Survey of Alabama sponsored geologic research in the Eufaula district to: 1) investigate the utilization of sandy kaolinS and other clays associated with bauxite-kaolin deposits; 2) find limits of the bauxite district, looking for possible extensions; and 3) study the geology of the district, looking for patterns or trends that may aid in finding new ore reserves. This work was done with the full cooperation of mining companies operating in the district and property owners. Research was aided by the U.S. Bureau of Mines and the University of Alabama. The investigation included detailed geologic mapping of mines, drilling in selected areas, and making mineral analyses of bauxite and clays. The mapping was performed primarily by pace and compass because of the complexity of the deposits studied, but aerial photographs were used to a limited extent. Drilling included both auger and core drilling. The auger drilling was limited to 100 feet, but core holes were drilled as deep as 200 feet. The term 'bauxite,' as used here, indicates a mixture of minerals containing more than 50 percent gibbsite. Bauxitic clay is a mixture of gibbsite and kaolinite that contains more kaolinite than gibbsite. The term "kaolin" indicates a clay composed of predominantly kaolinite. Other clays in the Eufaula district are composed of kaolinite, illite, quartz, mica, and goethite or hematite.

Jan 1, 1971

By L. Andrews, G. Smits, M. D. Adams, E. A. Viljoen

A new approach has been developed that is capable of ascertaining the ore component that is responsible for the preg­robbing of pregnant pulps. Many gold mines are currently treating ores containing a component that is detrimental to the recovery of gold, in that they "preg-rob" the pregnant pulp by adsorption of some of the dissolved gold. The identity of the preg-robbing component in this type of ore has been the subject of considerable debate over a lengthy period, th various suggestions including amorphous carbon, chlonte, chalcopyrite and layered silicates, such as the phyllosilicate minerals pyrophyllite, kaolinite, phlogopite and illite. A means is now available to identify and characterize the preg-robber in gold ores. This new approach consists of contacting the ore with a synthetic aurocyanide solution, identifying the mineral grains by optical microscopy and analysing each grain individually using high-sensitivity electron microprobe analysis. The approach is exemplified in this initial study by identifying the preg-robbing component in an active sample of gold-bearing shale to be an amorphous carbonaceous phase consisting of discrete particles of about 5 µm diameter interspersed with shale particles and agglomerated into grains of up to 100 µm diameter. Microanalysis of these grains as well as other mineral particles revealed that the gold content of some of the carbonaceous grains was close to 7000 g,lt, with no gold being detected in any of the other mineral phases that were found to be present (e.g. quartz, chlorite, muscovite, pyrophyllite, etc). Bulk analysis of the sample for carbon and gold confirmed that gold loadings of around 7000 g,/t would be expected if all of the gold were adsorbed onto the carbonaceous component. The carbonaceous constituent is probably also responsible for the anomalously high surface area measured for the material. It probably acts in a similar fashion to activated carbon, and the correct choice of organic blinding agent will decrease the extent of preg-robbing by lowering the activity of the material for gold, without causing any downstream problems such as fouling of the activated carbon used for gold recovery

Jan 1, 1993

By R. A. Lowe

Smectite is a common impurity in the kaolins of Georgia. This impurity is harmful to the low-shear rheology of kaolin slurries in concentrations as low as a few weight percent. The deleterious effect of smectite on the low-shear rheology is due to the swelling of the mineral. Montmorillonite containing clays were treated to precipitate a compact brucite layer {Mg(OH)2} in the interlayer region of the expandable layer silicate mineral. This treatment forms a hydroxy-Mg-montmorillonite with characteristics similar to chlorite. This treatment effectively reduces the swelling capacity of the mineral and improves the rheological properties of kaolin slurries contaminated with smectite impurities.

Jan 1, 1999

By Roderick G. Eggert, John E. Tilton

During much of the 1970s and 1980s, world metal consumption grew more slowly than during the 19505 and 1960s. The slowdown contributed to surplus capacity and low real prices because actual consumption was consistently less than expected as new mining and mineral processing capacity came on stream. Over the last year or so, however, world metal consumption has picked up noticeably, raising the question, Has metal demand returned to the long-run growth rates more typical of the 1950s and 1960s than of the 1970s and 1980s? This paper examines this possibility and, more generally, assesses the factors that will shape demand for the major metals over the longer term. TRENDS IN METAL CONSUMPTION The extent to which metal consumption has recaptured the brisk growth rates typical of the 1950s, 1960s, and early 1970s is shown in Figure 1. This figure traces the consumption of crude steel, primary aluminum, refined copper, refined lead, and refined zinc between 1960 and 1987 for the western world, consisting of the OECD countries (including the United States), and the developing countries. Consumption increased in 1987 for all five metals, and preliminary data for the first six months of 1988 suggest even more substantial increases, at least for the United States (U.S. Bureau of Mines, 1988). However, Figure 1 also shows that the recent increases in consumption are not untypical of similar surges during earlier periods of economic expansion and thus may reflect only cyclical or temporary factors. In short, the available data are unable to provide a clear indication of whether recent increases in metal consumption reflect the beginning of a new era of faster growth or simply a cyclical and temporary upturn associated with the expansionary phase of the business cycle. Consequently, to pursue this issue, we are forced to examine the underlying forces that will shape metal demand trends over the next decade. The approach we have taken involves two steps. The first examines the prospects for overall economic growth. The expectation is, the faster the economy expands, the faster the production of metal-containing goods grows.2

Jan 1, 1989

By James L. Vanderbeek

INTRODUCTION Semiautogenous (SAG) grinding technology first started to be seriously considered for comminution circuit design in the mid-1960s as an alternative to the three-stage crushing circuits and rod-ball mill circuits in vogue at the time. Since this time the application of SAG mill technology has become widespread with over 250 mills larger than 20 feet in diameter sold (Jones 2002). The vast majority of concentrators constructed over the past quarter century have utilized SAG mill technology, and a SAG-based comminution-based circuit is generally the first choice considered for new projects. Since the first generation of SAG milling technology was applied, many lessons have been learned, and new supporting technologies have emerged which make the design, installation and operation of SAG &-based grinding circuits more robust and efficient. This paper will discuss the current status of SAG and associated technologies. MILL MECHANICAL DESIGN ISSUES Table 1 summarizes the manner in which SAG design capability has evolved over the past 30 years. Increases in mill diameter came slowly as the industry took a wait-and-see attitude as the technology of larger mill diameters was advanced. The first 32-foot- diameter mill was ordered in 1969. It was not until 1979 that the technology jumped to the 34-foot-diameter mill and 1988 for the first 36-foot-diameter mill. The first 38- and 40-foot-diameter mills were both ordered in 1996. At least five 38-foot-diameter and two 40-foot-diameter mills will be in operation by mid-2004. Advances in structural analytical techniques and increased computational power, coupled with field measurements of large operating mills, have increased the confidence of the mill suppliers in their designs and the operating companies in the viability of larger diameter mills. No failures of a 36-foot-diameter mill or larger have been

Jan 1, 2004

By Patricia O. Milley

Two years ago, AlliedSignal embarked on a journey to improve QUALITY. However, the focus of this endeavor was on the CUSTOMER and not the traditional product focus. It wasn't that a focus to improve product quality wasn't fruitful in the past. We've practiced it in the chemical industry for many years with significant results. But our industry today is in a survival mode and yesterday's way of doing business is simply not good enough. In the mining industry, we have to make lug strides in how we do business or face losing our customer base. As you are well aware, other parts of the world are importing our technology at a rapid rate. We must work smarter to stay ahead of our customers ever more demanding need for higher quality at lower prices. With this as a driver, throughout the Corporation we reviewed in depth how we support our customers to keep them competitive and sought to eliminate work which did not help them reach this goal. Our first year of emphasis was on tools: how to hold meetings, gather data, and how to make decisions. This sounds very basic, I know, but you can't begin to imagine how productive meetings can become when you start with an agenda and prework delivered days in advance, and agree at the start of the meeting what should get accomplished. In the second year, we applied these tools to our work processes. We mapped how we do our work, scrutinized each step for value to the customer, and then set to work on how we could do things better. The areas we concentrated on were customer linked commercialization of new products, manufacturing and materials management. Our discussion today will focus on the commercialization of new products.

Jan 1, 1994

By William R. Beloff, Franklin M. Grynkewicz, Puza

Construction of the MBTA Red Line Extension through Somerville, MA, called for driving twin tube tunnels through a zone of approximately 83m (273 ft) with mixed face conditions. While the majority of the tunnels were driven through competent hard rock using drill and blast techniques, the mixed face zone was advanced using floating crown bars for primary support. The overburden consisted of medium clay, underlain by water bearing glacial till, over a sloping bedrock surface. Due to the unusual nature of the construction techniques, a program was undertaken by the Contractor to monitor ground movement and stresses in the temporary steel supports. This paper presents a description of the instrumentation employed, as well as the measured ground movements and support stresses. Additionally, the tunneling techniques are briefly presented and commented upon. PROJECT DESCRIPTION The Davis Square to Porter Square Tunnel Contract is part of the Massachusetts Bay Transportation Authorities (MBTA) Red Line Extension from Harvard Square in Cambridge to the Alewife Brook Parkway via Somerville. The 5.1km (17,000 ft) Red Line Extension consists of four major new stations, three of which will be interlinked via tunnel construction, and the remaining station will be the last link of an open cut portion, and a terminal point for this phase of the extension. This 866m (2,790 ft) portion began at Porter Square in Cambridge and rose at a 4% slope through Somerville, terminating at the new Davis Square Station. Twin tube tunnels were constructed through 763m (2,517 ft) of rock and 83m (273 ft) of mixed face conditions at the Davis Square end. Figure 1 presents a plan view of the entire contract.

Jan 1, 1981

By Jim Gebhardt

Douglas W. Fuerstenau (DWF) grew up on a farm and in several small communities in rural South Dakota during the depression years, where he learned the value of hard work. Working hard can produce results but being clever and hardworking will give you a bright future. In his later school years, Fuerstenau’s family moved to Rapid City where his intellectual curiosity and capacity helped him graduate with a B.S. in Metallurgical Engineering from the South Dakota School of Mines and Technology in 1949. His technical interests led to graduate studies and completion of a master’s degree from the Montana School of Mines in 1950 and Sc.D. degree from the Massachusetts Institute of Technology (MIT) in 1953.

By ERIK CHARRIER, ADITYA JUGANDA, Jürgen Brune, Gregory Bogin, Patrick Maier

Confined explosions are a major risk in underground coal mine operations. Depending on confinement, ignition location and obstacles in the flame path, methane explosions can transition to detonations. This research focuses on explosion experiments in a reactor with diameter of 71 cm and length of 30.5 m, along with developing the corresponding computational fluid dynamics (CFD) model that captures the observed flame behavior. The results show that the 2D and 3D CFD models are able predict the experimental flame front propagation velocity, but the 3D model shows more explicit conformity than the 2D model.

May 1, 2024

By Yi-Hsuan Chen, Jürgen Brune, Candace S. J. Tsai, Alejandro Munoz, Connor Krause

This study highlights the significant presence of submicrometer- sized airborne particles in underground coal mines, especially around the belt conveyor drift areas. Using realtime instruments and gravimetric samplers, the assessment revealed that particle concentrations were notably higher in the belt entry compared to other locations, with a strong presence of submicrometer- and nanoparticle-sized dust. The study’s findings emphasize the importance of addressing small particle exposure, as these particles, composed of harmful substances like calcium, copper and iron, can pose serious health risks to miners. This research emphasizes the importance of improving air exposure estimation through more effective monitoring and characterization techniques to better understand and reduce workers’ exposure to hazardous airborne particles in the mining environments.

Apr 1, 2025

By D. Diggins

Experimental apparatus for the determination of powder wettability is described. The principle of the technique is based on the measurement of the equilibrium capillary pressure in a packed bed of particles. Both the macroscopic solid-solution-vapour contact angle, e, and the specific surface area, A(m2g-1), of the powder, can be obtained. Experiments on angular quartz particles have been performed. A wide range of situations have been covered: hydrophobic and hydrophobic particles wetted with water, a variety of organic liquids and solutions of surfactants. The results show that reliable and reproducible values for 0 and A for angular and relatively coarse powders can be obtained with the proposed equipment for advancing liquid fronts in the absence of soluble surfactants. In the latter case and for receding liquid fronts in general, only qualitative trends have been obtained.

Jan 1, 1992

By Panshi Xie, Yingyi Zhang, JIANJIE DUAN, Shenghu Luo

The most important safety aspect associated with great mining height in steeply dipping coal seam mining is the stability and control of the roof. When soft coal and hard gangue make up the immediate roof of a working face, the soft-coal interlayer plays a significant role in gangue damage and can cause problems such as roof collapse in front of the support, collapse of partial area supports and other problems that can affect the stability of the supports and the surrounding rock system. This study found that the first weighting step of a multigangue roof is larger than that of a nongangue roof, but periodic weighting steps are similar. The overburden collapse height is lower in a multigangue roof than in a nongangue roof due to the buffering and supporting function of the collapsed gangue. Failure of the coal interlayer is the key factor in the collapse of multilayer gangue. The limited load of the interlayer and maximum resistance of the support is concluded by the hard gangue and soft coal interlayer mechanical model. The maximum resistance of the support increased with the dip angle of the seam and burial depth. Certain measures are proposed to control the stability of the gangue roof, including zoning control of the mining height and resistance and advancing the support while maintaining roof contact, thus ensuring the integrity of the support and surrounding rock system.

Steady state simulation has become a highly effective approach to the optimization of existing mineral processing plants and the design of new facilities. Accurate phenomenological models imbedded in user-friendly software packages make this advanced technology available to the mineral processing engineer. The new version 2.0 of the USIM PAC software package contains many improved features, and a new Windows 3 graphics interface. The main features include Objective-Driven Simulation, new fields of application, improved data processing algorithms and improvements in the design and optimization capabilities.

Jan 1, 1992

By J. Roth

PROLOGUE Nowadays, where production costs and energy costs are increasing and at the same time requirements in fineness and purity of industrial mineral products are getting higher and higher, industry has to look for more efficient grinding systems and developments to produce these products more economically. Therefore lots of new developments in high energy jet mill pulverizing have been made. In the main, however, these developments involved more or less just the new principle of fluidized bed jet pulverizers but not the older spiral jet mill principle. In some cases, especially in the filler industry where laminar minerals are used and higher aspect ratios are required, the spiral jet mill principle has advantages in a better delamination of these minerals. To comminute minerals down to products with a d97 < 3 µm, the specific energy consumption increases up to 2,000 kWh/t – 3,000 kWh/t or even more, depending on the grindability of the mineral. So the production of these fine materials is quite an expensive task. But jet mill grinding is and will be the most favorable method to produce micro-products and in the near future nano-products, despite the high energy consumption.

Jan 1, 2000

Liebherr Mining Equipment Co., of Newport News, VA and Baxter Springs, KS, introduced the T282, a new two-axle, diesel-electric, AC drive haul truck with a payload capacity of 327-t (360-st). The T282 was unveiled at a press briefing in October 1998 at the company&apos;s Baxter Springs research and development1 manufacturing facility. In addition to an increase in pay- load capacity, the truck&apos;s AC drive system has been de- signed to allow for easy configuration to a trolley-assist system with minimal additional equipment. The T282 provides fuel savings, reduced maintenance requirements, and reduced downtime and maintenance costs, providing the mine operator with increases in productivity. Basic dimensions and weight of the T282 are: ? Overall length, 14.5 m (47.5 ft). ? Overall width, 8.7 m (28.7 ft). ? Loading height, 6.5 m (21.2 ft). ? Height - body up, 13.9 m (45.9 ft). ? Empty vehicle weight, 201 t (221 st). ? Operating weight - loaded, 528.6 t (582.6 st). ?Engine, Detroit Diesel 16V4000 at 2 MW (2,750 hp). ?Electric drive system, Siemens/Liebherr.

Jan 1, 1999

By J. Willison

Over the past decade, the coal mining industry has faced the difficult task of remaining profitable in the midst of declining market prices. Historically, the industry has been quite capable of meeting this challenge by various means. As total costs to mine and market coal continue to increase, new methods of tackling the problem must be implemented. Studies have shown that although many options exist to influence both inby and outby costs, the greatest potential remains in addressing costs at the coal face. Mining operations can positively effect a change in their profitability by either reducing costs, or by increasing production to in turn lower their net cost per man-hour. Original equipment manufacturers can play a key role in both options through the introduction of new technology that permits higher extraction rates, as well as other advantages leading to lower cost coal. A leading advancement over the past 30 – 40 year period has been the advent of progressively higher voltages to operate the mining equipment. This advance enables higher power transmission for a given cable size, operation at lower amperages resulting in less voltage fluctuation, and reduced heat on the cable and electrical components.

Jan 1, 2003

By J. M. Schisler

In the last five years Eldorado Resources Ltd. (ERL) has undergone a major expansion and modernization of its uranium refining and conversion plants. A new refinery for processing yellow cake to UO3 was constructed at Blind River in northern Ontario and started up in 1985. Its rated capacity is 18,000 t/a uranium as UO3. At Port Hope, Ontario, ERL&apos;s new UF6 conversion plant has been constructed. This plant started up in 1984. It utilizes the novel, wet-way process to produce UF4 and gives the company a UF6 production capacity of 14,500 t/a U. Also at Port Hope is Eldorado&apos;s ceramic UO2 powder production facility, commissioned in late 1980. It has a capacity of 1700 t/a uranium as UO8. With the completion of these capital projects, Eldorado has the largest and most up-to-date refining and conversion facilities in the western world. This paper reviews the refining process and process design. The methodology used to start up the Blind River plant is described as are some startup difficulties, solutions that were developed, and the resultant current operation.

Jan 1, 1987

By William C. Larson

The number of uranium in situ leach operations has increased significantly since 1975. As of May, 1980, there were a total of 27 active projects, including 16 commercial scale operations (or under construction) and 11 pilot scale operations. The south Texas uranium district and Wyoming have been the most prominent areas in early field experiments as well as in commercial application of this new recovery technique, although in situ leach tests are now being conducted in Colorado and New Mexico. The growing number of commercial-scale operations is accepted as prima facie evidence that in situ mining now offers a third option along with open pit and underground mining for winning uranium from sandstone host rocks. It is estimated that in 1979 about 9 percent of the nation&apos;s total uranium production was from in situ mining. However in situ mining of uranium is not without its environmental controls. The primary emphasis of environmental controls falls into two catagories; namely, control of the leach solutions during mining and demonstration of ground water restoration. Finally this paper briefly reviews the Bureau of Mines research program in uranium in situ mining.

Jan 1, 1980

By Erwin Riyanto, Roy William, Karl Llewellyn

The Deep Mill Level Zone (DMLZ) mine is currently one of the deepest block cave mines in the world. The rock mass is heavily veined with little to no joints and faults are usually healed cohesive structures leading to difficult cave mining conditions. The caving process is improved if the rock mass contains fractures with sufficient density that it will cave by gravity as undercutting progresses. Hydraulic fracturing (HF) has been used to create fractures around the cave to improve mining. A seismic monitoring system has been used in DMLZ since the start of mining. Therefore, the seismic activities before, during and after HF can be monitored. Shear wave splitting is a process used to study the impacts of HF on the rock mass. This process involves the measurement of travel times from splitting shear waves after seismic events and using this to define the anisotropy within the rock mass and subsequently fracture density. This paper sets out the methodology for carrying out the interpretation of the shear wave splitting process using seismic data from the fracked cave crown and abutments along with an overview of the benefits to cave mining as result.

Apr 26, 2022