Search Documents

By Robert F. Kaufmann

INTRODUCTION In response to the Uranium Mill Tailings Radiation Control Act (Public Law 95-604, Section 114c), a report has been prepared by the U.S. Environmental Protection Agency (1980) which describes the potential health and environmental effects associated with uranium mine wastes. The author was responsible for the geology, hydrology and aqueous pathways analysis portions of the report. All potential sources of contaminants, solids, liquids, and airborne emissions, which might cause adverse impacts upon the environment or health of nearby populations were considered. Wastes at both active and inactive uranium mines (Hans and O'Connell, 1981) are described and assessed with respect to dose and health effects (Blanchard et al. 1981). The emphasis of this paper is on the liquid emissions and the aqueous pathway. Model uranium mines were developed for surface and underground mines. The model underground mine was placed in New Mexico while the model surface mine was in Wyoming. Development of a generic assessment was complicated due to the inherent variability of uranium mines. Also, most information available relates to uranium mills rather than to mines, or reported measurements were often influenced (biased) by wastes from a nearby mill and did not specifically reflect mine discharges. Consequently, the assessment presented is often based on conservatve (maximizing) assumptions which are identified as such, and which were based on knowledge from field investigations, available literature, and consultations inside and outside the U.S. Environmental Protection Agency. Maximum use was made of available data, supplemented with limited field studies in Colorado, Texas, New Mexico, and Wyoming. PREVIOUS INVESTIGATIONS Stream survey work in Colorado by the Water Pollution Control Commission and the U.S. Geological Survey (Moran, 1974; Wentz, 1974) mentioned a portion of the Uravan Mineral Belt and uranium mines therein, but the work did not emphasize uranium mines. Significant amounts of acidity and total trace metal concentrations were found in streams from 18 different mining areas. Dilution and chemical precipitation below mine drainages decreased concentration and increased the pH. Given enough time and distance, the streams recover naturally, but the accumulations of trace metals in the sediments increase. Field observations in 1971-72 of streams in most of Colorado indicated that approximately 724 km of streams in 25 different mining areas were adversely affected by mine drainage (Wentz, 1974). Discussions of the impacts of uranium mining on water quality or quantity are incidental in numerous impact statements and environmental reports prepared by industry and (or) the U.S. Nuclear Regulatory Commission as an integral part of licensing or relicensing uranium mills. Coverage on mining is usually minor as the principal focus is on milling impacts. The same is true for the recently prepared generic EIS on regulation of uranium milling (U.S. Nuclear Regulatory Commission, 1979). Radiochemical assessment of surface and groundwater in uranium mining districts of New Mexico is done by self-monitoring programs associated with NPDES permits. Also, radiochemical assessment studies have been funded by the New Mexico Environmental Improvement Division and U.S. Environmental Protection Agency. Unfortunately, there has been no concerted effort to prepare broad assessments of the cumulative impacts of mining and milling in areas of interest in Texas, New Mexico, and Wyoming. Critical review and synthesis of these types of data can produce rather useful information. For example, the publication "Water Quality Impacts of Uranium Mining and Milling Activities in the Grants Mineral Belt, New Mexico" (U.S. Environmental Protection Agency, 1975) addresses the groundwater and surface water changes as the result of extensive uranium mining and milling production in a relatively confined area. A more recent report by the Wyoming Department of Environmental Quality summarizes 16 years of aqueous radium and uranium data. The study reports significant amounts of radium-226 and uranium were present in surface water in the Shirley Basin as a result of inadequate mine water treatment (Harp, 1978). In Texas, surface water and groundwater monitoring conducted by industry, as well as by State and Federal agencies, reveals little or no change of chemical quality attributable to uranium mining and milling (Gesell, 1977; Kallus, 1976). This conclusion is based on 586 samples collected from 198 stations over a period of 39 years, but primarily from 1961 to 1975. The State monitoring program by several agencies is continuing, but data reporting and interpretation is lagging. One survey (Itin, 1975) showed that none of the mine water from the 10 lakes that were sampled was suitable for human use. The lakes were also unsuitable for irrigation due to mineralization of the water by sulfate, chloride, and TDS. One of the 10 was suitable for stock watering.

Jan 1, 1981

Crushing and grinding activity in 1989 followed the rapid pace of the mineral industry. Use of existing installations, demand for expanded capacity, and implementation of entirely new operations contributed to a high level of activity. At the 1989 SME-AIME Annual Meeting in Las Vegas, NV, the crushing and grinding session focused on wear materials in crushers and mills. Another session joined the process control group in its simulation-modeling and control of crushing and grinding circuits. Both sessions addressed the optimization in operating effectiveness. Specific subjects covered grinding media wear of forged and cast grinding balls and rubber lined mill liner wear. Also, the Semi Autogenous Grinding (SAG) Mill Conference in Vancouver in September 1989 provided a valuable update on the progress of SAG operations in recent years. Operationally, gold grinding and roasting circuits were implemented in 1989. Freeport McMoRan Gold started up two operations in Nevada. Two other circuits, both using SAG mills, are scheduled to start in 1990. These will be in Nevada and British Columbia. Elsewhere in gold, additional capacity continues to be brought onstream, both domestically and worldwide. In copper, expansions continue to call on additional crushing and grinding units. The unrest at Bougainville in Papua New Guinea has fueled a continued, strong demand for comminution in the copper sector. Specific equipment installed or started in 1989 included the ac variable frequency drive SAG mills in Australia, Alaska, and Papua New Guinea. Also, the gearless drive SAG mill in Chile provides tremendous flexibility in terms of mill speed. The trend toward moveable in-pit crushers continues -even at established operations.

Jan 1, 1990

By Bryce T. Tripp

Utah produces a wide variety of industrial rock and mineral commodities, valued in 1998 at $534 million (28 percent of the total non-fuel mineral production of Utah). Major commodities produced in 1998 include: halite; potash and magnesium chloride; Portland cement; sand and gravel; car- bonates including lime, limestone, and dolomite; phosphate; crushed stone; clays; perlite; gypsum; and sulfur and sulfuric acid. Commodities produced in lesser amounts include: diatomite; pumice; silica; lightweight aggregate; gemstones, ornamental stone, and mineral and fossil specimens; byproduct sulfur and sulfuric acid; silica; and building stone. The years 1993 through 1998 were a period of steady growth in industrial rock and mineral production. However, some commodities have grown much more rapidly than others. The robust western U.S. economy has stimulated production of construction-related commodities like sand and gravel, raw materials for Portland cement, lime, and building stone, resulting in exploration for raw materials, development of new quarries, and expansion of existing plants. Noteworthy specific developments include: (1) opening of new aggregate operations and buyouts of small aggregate operations by large national and international firms, (2) expansion of a lime operation and two cement plants, and (3) development of several new gypsum mines. The future of the industrial minerals industry in Utah looks promising despite a more restrictive regulatory environment and a growing anti-development attitude among its citizens. While Utah has become less pro-development than it was prior to the 1990s, it is still moderate compared to strongly anti-development states, so companies have some motivation to choose Utah in their strategic mineral development plans. As long as the western states' economies continue to grow, Utah's industrial minerals industry should thrive.

Jan 1, 2001

By Richard V. Wyman

The genesis of ore deposits has been tied to plate tectonics through differential petrogenesis in subduction zones. However, many mineral districts, especially in the Basin and Range province of United States and Mexico, appear unrelated to any possible subduction zones or to plate boundaries. It is proposed that the pattern of mineral belts is related to mantle plumes which have been overridden by an advancing continental margin.

Jan 1, 1976

By Benjamin K. Pocock

When considering alternative equipment choices in mill or process flowsheets, it is important to determine both capital and operating costs of such equipment as well as other possible savings related to downstream operations. This paper presents a few case studies and shows cursory guidelines for the selection of equipment for new installations or in the retrofitting of existing plants. Based upon recent plant experience, suggestions are given to improve the operation of clarifiers, thickeners and vacuum filters.

Jan 1, 1986

By Lee Herold Storey

Groundwater remediation is growing in occurrence in the western United States. Groundwater remediation programs are regulated by state water quality statutes. The remedial action plans implemented under these statutes may conflict with well-established existing rights to withdraw groundwater for beneficial use. This paper discusses how the states of Arizona, Colorado and New Mexico administer conflicts between the need to withdraw and remediate groundwater with the existing rights of others to withdraw groundwater for beneficial purposes.

Jan 1, 1991

By Edwin G. Johnsen

Underground mining is relatively safe today, but no technique or equipment is completely fool proof and 100% reliable. The only sure way to prevent accidental death or injury to underground workers is to remove them completely from the hazardous environment. This alternate approach to underground work is now feasible. Tunnelling and mining systems can be built that could be remotely controlled by men operating consoles in a surface control room. This concept, called a teleminer, would use recently developed remote control technology to remove man from underground work but still give him the capability to remotely operate mining and excavating equipment as if he were actually in the working area. It is appropriate to present this concept in the session "Environmental Controls" because the rationale for environmental control in underground areas can be significantly modified if man is excluded from the underground operation. The development of teleminers cannot only reduce or eliminate most of the requirements for conventional environmental control, but it can also create new and powerful techniques for rapid tunnelling and excavation. TELEMINER CONCEPT The concept of remotely controlled mining machines is neither new nor untried.(1)(2) Conventional remotely controlled mining equipment employs the standard techniques of extending the controls of the equipment to a remote console. For example, the rotary cutters on a remotely controlled tunnelling machine are started or stopped by a human operator turning a switch on the remote control console.

Jan 1, 1997

By E. Yan, M. Mankosa, G. Luttrell

"During the past decade, column flotation cells have become widely accepted for upgrading ultrafine sulfide ores. However, the use of columns has been widely relegated to cleaner circuits due to their comparatively high selectivity derived from the use of wash water dispersed over a deep froth. High tonnage rates and low feed grades make using column technology in roughing and scavenger stages challenging due to the resulting size of the needed equipment. To specifically address this challenge, a new high-intensity flotation system known as the StackCell™ was developed. This technology makes use of a novel pre-aeration method coupled with froth washing to simultaneously provide improved flotation kinetics and selectivity. The novel aeration system provides efficient bubble-particle contacting thereby shortening the residence time required for particle collection. This article reviews the technical design features of this new flotation technology and presents recent data from in-plant pilot testing in a copper-sulfide application. INTRODUCTION Column flotation cells have become very popular in the minerals processing industry for cleaner circuits due to their ability to produce a high-grade froth concentrate via the use of froth washing (Luttrell et al., 1999; Kohmuench et al., 2004). The use of wash water minimizes the nonselective recovery of ultrafine impurities that are normally entrained into the froth product from conventional flotation machines. On the other hand, the unique design of a column cell typically requires a large tank volume. Column cells must be tall to ensure that the pulp residence time is long enough to offset their inherently slow flotation kinetics and to minimize internal mixing that is detrimental to overall cell performance. The tall design minimizes the total floor space required for the column installation, but substantially increases the foundation load. The large size of the column tank can also create issues during fabrication, transportation and installation. To address these concerns, the engineering team at Eriez Manufacturing developed a next-generation flotation technology called the StackCell?. This high-intensity flotation machine was designed to provide column-like separation performance within a very compact volumetric footprint. This article describes the key working features of this new technology and provides data from recent pilot-scale tests conducted in gold and copper-sulfide applications"

Jan 1, 2016

By John Frostiak, Don Welch, David Landriault

The use of paste technology for underground cemented backfill is widely accepted in the mining industry today as a potentially cost effective alternative to cemented rock and hydraulic slurry fill. While paste backfill is not the appropriate backfilling method for all mines, there are presently 23 operating tailings paste backfill plants throughout the world. This new technology has gained increasing acceptance as a backfill method over the last decade and its use is now expanding into the surface disposal of tailings using the stacked, thickened tailings disposal concept. Over the next 18 months there will be ten new paste plants commissioned in the world. Five of these ten plants will be used exclusively for surface tailings disposal or a combination of surface disposal and underground backfill production. The thickened tailings disposal concept, developed by Dr. Eli Robinsky in the early 1970's, has been in use for decades at several mine sites throughout the world (Kidd Creek Mine site in Northern Ontario), but always utilizing non segregating high density tailings slurry central discharge, stacked tailings placement. With the use of a higher solids content paste, the typical 2-degree beach angle can be increased to ten degrees or more with no runoff water and minimal shrinkage crack development through desiccation. This paper presents the design of the first mine to implement true surface paste disposal, Barrick Gold Corp's Bulyanhulu Mine in Tanzania. The paste system will be commissioned in the first quarter of 2001 allowing performance data to be collected to define the full potential of paste technology for surface tailings disposal.

Jan 1, 2001

By Peter Kolitsch, Galyn Rippentrop

INTRODUCTION On April 14, 1994, the joint venture of Kiewit Construction Company and Kenny Construction Company was awarded a 76 million dollar contract for the construction of the New Hampshire Avenue Tunnels in Washington D.C. The Notice to Proceed was given on May16, 1994 and scheduled completion is September 1997. This project is one of five contracts for the Mid-City E Line as part of the Washington Metropolitan Area Transit Authority (WMATA)Greenbelt Route. Once completed, the Mid-City E Line subway tunnels will connect service between the U Street-Cardozo and Fort Totten stations (See Figure 1). The New Hampshire Avenue Tunnels project consists of approximately 6800 feet of twin single track subway tunnels, three vertical shafts, associated utility work and comprehensive restoration work. Section E4b involved two methods of tunneling along the project alignment. The first method consisted of the well known soft ground open face shield driven tunnel and the second method consisted of tunnels driven using the New Austrian Tunneling Method (NATM) . The NATM section of twin tunnels begins at the Buchanan Vent Shaft and proceeds approximately 2630 feet under Rock Creek Cemetery, including the Farragut Emergency Access Shaft and connects approximately 390 feet beyond to the existing Fort Totten running tunnels (See Figure 2). Special considerations had to be given to the portion of the tunnel alignment which passed beneath Rock Creek Cemetery. The analyses and subsequent selection of the tunnel support system were based on anticipated geological conditions and the sensitive tunnel alignment. The New Hampshire Avenue Tunnels project was the second soft ground NATM project in Washington D.C. The first, by no coincidence, was completed at the adjacent Fort Totten Station and Running Tunnels Project by Mergentime/Hochtief, AJV. Currently, on a nearby WMATA jobsite, the J.F. Shea Construction Company has started a third NATM soft ground tunnel. Tunnel support systems were studied with respect to three tunneling methods: •A one-pass system consisting of a bolted precast concrete segmental lining •A two-pass system consisting of an unbolted precast concrete segmen

Jan 1, 1997

I reached New York at the start of my second South American adventure on Jan. 9, 1916. In the Anaconda office I found that we were not to take the steamer for two weeks which gave me time to study reports on Potrerillos and Corocoro. Reno Sales, whom I had met in Butte only casually, was to go with us to South America. Though he was only a little older than I, he was already an unquestioned leader of our profession, and we became and remained good friends. William Braden was in New York and would return to Santiago with us. Tom Hamilton would also be returning from a vacation. Leighton Stewart, a young engineer who was to work for Braden, was going on the steamer with us, taking along his wife. And of course Dr. Ricketts would go along. He had just become engaged to John Greenway's half sister, Kate Greenway, and in order not to be away from her longer than was necessary, he did not reach New York until a day before we sailed. This made eight of us who would be in the party. We were to go to Corocoro first, as Braden had taken an option on the Chilean company there. Development was already under way. As reports came in by mail we tried to get as good an idea of the property as we could before the actual examination. Mr. Thayer "put us up" at India House, one of the best lunch clubs in New York, and Reno and I ate our lunches there almost every day. Thayer, Braden, and Cornelius Kelley, who was to succeed Mr. Ryan as president of Anaconda, joined us when they could. At the lunches they told us about the under- ground war in Butte a few years earlier. When I wrote my chapter on the Butte wars in Romantic Copper more than 15 years later I could not help being biased a bit by my friends, all of whom were on the Anaconda side. But their opponents in the Clark and Heinze camp were just as biased in their comments on my book.

Jan 1, 1976

The mining industry is one of the three pillars of the Namibian economic development, besides tourism and the fishing industry. Generating 20 % of the GDP and more than 50 % of the export income, half of this amount derives from the diamond mining industry. In 2008, the annual production of 2.2 mio carat achieved an income higher than 1.44 billion Namibian Dollars (more than 750 mio Euro). After the global recession in early 2009, which also caused a significant downcrease in production to only 0.93 mio Carat, the diamond mining industry easily restored itself and the production figures for 2010 are expected to be even higher than those achieved in 2008. Compared to other diamond producing countries, Namibia is mainly producing diamonds of highest quality (jewellery quality), with less than 10 % of the mined diamonds not falling into this category. This high quality stands also for the worldwide highest prize achieved per carat. With 370 $US per carat it is more than four times higher than that of the average South African stone. In 1908 the finding of the first diamonds in the Namib desert close to the coastal town of Lüderitz was reported by a Mr Stauch, railway inspector for the then German colonial railway company. This event immediately triggered a Diamond Rush and subsequently the set-up of the restricted diamond mining area ?Sperrgebiet? through the German colonial administration. In 1913, only five years after the first mining operations had started, the steadily increasing production allowed for more than 20 % of the diamond production worldwide. After the First World War, the new South African government concentrated all mining activities in one organization, CDM (Consolidated Diamond Mines of South West Africa) which in following decades conducted an extensive and detailed exploration of the whole Sperrgebiet and started numerous new diamond mining operations.

Jan 1, 2011

By Michael R. Birkos

A new electrotelluric prospecting technique allows the mapping of ore body distribution, lithologic contacts, and voids with accurracy comparable to core drilling. Data is available almost immediately and presented in a format similar to a downhole log. This is done with a passive surface receiver that transduces electrotelluric radiation into an audible signal. Changes in the character of the audible signal lends insight into lithology, porosity, fluid type and medium. Three case histories are presented. The first delineated a paleochannel within a coal seam. The second traced old mine workings and backfill areas. The third identified a high-pressure karst void.

Jan 1, 1986

By P. Somasundaran

Previous studies on semi-soluble minerals such as calcite (1) and apatite(2) and sparingly soluble minerals such as quartz (3,4) have given evidence for significant changes in their electrokinetic properties as a function of aging time. Such changes are relevant to mineral processing operations where the crushed ore particles might not have yet reached equili¬brium with the water that it is in contact with. In order that these changes be studied under controlled experimental conditions for long periods unattended or with fairly less intermittant attention, a streaming potential apparatus with an automatic streaming system was constructed. Also, a new streaming potential cell was incorporated into the system so that the effect of temperature, a variable coming into increasing usage in mineral processing operations(5), could also be studied. Conventional streaming cells(6) cannot be safely employed to conduct studies as a function of temperature since they have many glass joints that are prone to leakage, parti¬cularly under pressure, in the course of an experiment. This paper describes the new apparatus and some typical results that have been obtained with it far temperature effects.

Jan 1, 1973

By Stephen H. E. Phillips

Geological and hydrological conditions in the strata overlying the Salado Formation vary considerably in the Carlsbad, New Mexico area. The first four shafts sunk at international Minerals and Chemical Corporation's property have been located in competent and essentially dry conditions, while other shafts on adjacent properties have had such adverse conditions that ground freezing has been chosen as the water and ground control technique for shaft sinking. At the location of the IMC No. 5 Shaft there has been extensive-erosion and salt dissolution in the Rustler Formation which has led to collapse of some zones of the strata. Both ground freezing and pregrouting were considered as alternative methods of stabilizing the extremely poor ground conditions and controlling the potentially very heavy water inflows it was decided that pregrouting the shaft was feasible and would offer substantial cost and time saving over a ground freezing technique. This paper describes the pregrouting techniques used and illustrates the requirement for flexibility in a grouting program so that it can be codified to reflect any new or additional information which is obtained during the progress of the grouting.

Jan 1, 1984

By Russell K. McFarland, Eugene L. Foster

INTRODUCTION The U. S. Department of Transportation has underway an important new program which will have a major impact on rapid excavation technology. The Transportation Tunneling Program, as it is called, is a coordinated, multi-modal research and development effort. Its goals, if realized, will significantly improve our ability to build the underground structures needed for transportation. This, in turn, will improve transport efficiency, environmental impact, and the energy consumption associated with the movement of people and goods. Tunneling technology research and development had its beginning at the Department of Transportation in the Office of High Speed Ground Transportation (OHSGT). The OHSGT developed and implemented a program in 1965 to provide the technology for underground construction needed to support future high speed ground transportation. In 1967, when the OHSGT was transferred from the Department of Commerce to the Federal Railroad Administration (FRA), the program accompanied that office. The thrust of the FRA program has been cost reduction through the development of new materials, innovative designs, and better construction methods. During the late 1960's and early 1970's, other developments were underway which would influence the future of tunneling research at the Department of Transportation. An ad hoc

Jan 1, 1974

By Shouci Lu, Keji Sun, Dianzuo Wang, Yiqun Li, Chuang Jin

The dephosphorization of iron ore and reduction in Fe loss in process are currently the foremost technological challenges facing the mineral industry of Meishan Iron Ore. These problems can be resolved to a greater extent by an apatite flotation process which depends on selective flotation reagents. The primary objective of this research work is to develop new type of flotation collectors for dephosphorization of weak magnetic iron ore. Detailed discussion is given on the influence of collector dosage, pH, dispersants and pulp temperature on the flotability of apatite, siderite and hematite using the collectors of Oleyl sarcosinate(OSS), Alkyl polyoxyethylene ether phosphate (AEP) and the mixtures of OSS and AEP A key feature of the flotation was the use of the mixtures of OSS and AEP as a selective collector for phosphate. The effects of chemicals and operational variables on the phosphorus flotation from the weak magnetic iron ores have been investigated. The test results shows that floating the phosphorus minerals with new type collectors can reduce the phosphorous content in the flotation concentrate to an acceptable level of less than 0.20% P with increased Fe recovery.

Jan 1, 2002

By Winthrop F. Watts, Robert W. Waytulonis

During the 1980's. the Mine Safety and Health Administration (MSHA) proposed new regulations for the use of diesel equipment in underground coal mines, and the National Institute for Occupational Safety and Health (NIOSH) recommended that whole diesel exhaust be regarded as "a potential occupational carcinogen", and that reductions in exposure to exhaust pollutants would reduce excess risk. During the same time, the Bureau of Mines tested new emission control technology to minimize diesel emissions. The objectives of this paper are to discuss the major issues regarding diesel exhaust emissions. especially diesel particulate matter (DPM) , and to highlight emission controls that will be available. DPM is a potential health threat because it is respirable in size and is composed of nonvolatile carbon with adsorbed or condensed compounds. These compounds include potentially mutagenic or carcinogenic hydrocarbons such as polynuclear aromatic hydrocarbons and sulfates. DPM contributes to the degradation of air quality in mines with typical mean concentrations ranging from 0.2 to 1.0 mg/m3. In addition to adequate ventilation, control of DPM can be achieved by implemention of improved work practices, regularly scheduled engine maintenance, and emission controls.

Jan 1, 1991

By Ronald C. Bethard, Kenneth W. Ely

The liberation of methane during underground coal mining causes serious safety concerns. During a mining cycle, with mechanized mining equipment, thousands of cubic feet of methane are released from coal seams, discharged to return air courses, and vented to the atmosphere through mine fans. This has been the traditional way of removing the explosive hazards of methane gas from the mine. Through horizontal and vertical degasification techniques, this hazard can often be handled in an equally safe and much more profitable manner. Basically, degasification allows for the controlled reduction of inseam methane content of coal prior to its mining. It is the responsibility of mine management to evaluate these degasification programs and ensure that the program itself does not introduce some new risk to the mining process. The removal of methane gas from underground coal mines using horizontal and vertical degasification is a relatively new concept. Products and systems used in degasification continue to evolve. Site conditions vary also, so no one system or equipment can be said to be the safe answer for degasification in all situations. A constant process of cooperation and evaluation by mining and degasification management should result in a safer and more profitable mine.

Jan 1, 1989

By G. Ansong, P. K. Achireko

The authors present a new mineral price model, compare it with time series and naive models, and analyze the effects of the forecasting models on mineral project evaluation. Mineral commodity prices are volatile, which means that the results of evaluation tools that do not treat the stochasticity of metal prices rigorously may be misleading. But, in mine valuation, commodity price forecasts are required to assess the economic viability of a project. In this study, a new mineral forecasting method, called the MNDRVG-MFNN-RM model, which incorporates randomness, neural networks and regression models, is introduced. The MNDRVG-MFNN-RM model, a naive method and time series model were used to forecast gold prices for two successive years for the evaluation of a proposed open-pit mine. The MNDRVG-MFNN-RM model yielded the best results among the three methods. It produced the true optimum pit limits and an optimum pit value slightly less than the true optimum value. The main novelty of the methodology is the simulation and rigorous analysis of the randomness property associated with mineral prices to reduce the estimation and forecast errors, an important contribution to mineral venture evaluation, mine planning and design.

Jan 1, 2000