Search Documents

By V. P. Keran, K. Leung

Two 32 foot x 14% foot, 6.4 MW autogenous mills have been installed in the Mount Isa Mines Copper Concentrator to replace the fine crushing plant, fine ore bin, rod mills and primary ball mills. This paper describes the reasons for the change, the rationale for the new circuit design and configuration, the design and scale-up processes used to size the mills, considerations for the installation of large mills inside an operating concentrator and some early operating data.

Jan 1, 1992

By Y. T. M. Ocsa, V. O. Tenorio

This research is the result of a geotechnical study carried out in a natural slope in an Open Pit mine in Southern Peru, highlighting earthquakes as an important cause of instability within the case study presented. This leads to analyze the stability of a slope, according to the safety factor and thus consider a future construction in its environment according to the identified requirements. There are known disasters at national and international level that involve human lives because of the lack of analysis of slope stability conditions, which based on the results will allow to control and to take adequate corrective measures. These mass movements are classified whether they are soils or rocks, considering the mechanism and type of rupture, as well as the presence of water, the speed and magnitude of the movement. The movement problems are due to factors of inherent nature and constitute a reason to perform a calculation study to analyze and estimate the safety factor of each of the evaluated cases

Mar 2, 2022

By Ronald O. Harma

Iron ore pellets made from concentrates produced from low grade iron ores are the primary iron bearing feedstock for iron making in North American blast furnaces. Steelmakers are demanding increasingly higher quality to provide for improved blast furnace productivity, efficiency, product quality and environmental compliance. Unfortunately, this higher quality iron ore product must be produced from the vast deposits of low grade iron ores that are becoming increasingly poorer in quality with regard to mineral liberation and ease of concentration. Since some of these low grade iron ores require grinding to as fine as 90% -500 mesh (25 microns) for liberation and since more of the silicious gangue and other minor undesirable constituents must be removed to provide the higher quality, we have come to depend on flotation to do the added work. Flotation technology and other preflotation unit operations must improve to meet these increasing demands. In many cases, flotation equipment, reagents and circuit operating performance have improved little during the last two to three decades. Mechanical flotation cells have grown from 14 cubic meters (500 cubic feet) to over 84 cubic meters (3000 cubic feet) to help reduce capital and operating costs; however, flotation metallurgical performance has not improved, Column flotation has only recently shown promise in improving metallurgical performance for iron ore rougher flotation. Previous column flotation success was mainly in scavenger and cleaner flotation steps for treating minerals other than iron ore. Although some new flotation chemicals have been developed for removal of silica and other minor constituents under widely varying mineralogical scenarios, recovery of iron mineral has not improved. The operation and control of flotation circuits have become more challenging because of the increasing workload on flotation. Better sensing, process control and operation of flotation circuits are essential as we go forward. Iron ore upgrading by flotation can be classified into either anionic or cationic methods. Anionic flotation of either iron oxide or silicious gangue is accomplished by collector type, pH control and selective chemical activation . Similarly, cationic flotation of silica or iron oxides is accomplished by collector type, activation and/or pH control. Removal of other minor constituents is achieved by using specialty chemicals under controlled conditions for preflotation, co-flotation or post flotation steps. Generally, anionic flotation is used for floating cleanly liberating crystalline oxidized iron ores such as hematite, specularite and martite. Earthy and hydrated oxides such as hematite and geothite can be upgraded with either anionic or cationic collectors after controlled dispersion of slimes or prior removal of slimes. Anionic flotation of silicious waste can be achieved by calcium activation of silica. For magnetic iron ores small amounts of locked silica particles (middlings) can be removed by cationic silica flotation, which is the only method in commercial use in North America today. Historically the efficiency of these iron ore flotation processes has been restricted by the loss of fine iron particles (minus 500 mesh) to the tailings product. New technology is required to overcome this loss and improve overall flotation performance. Development of technology for more selective separation of silica and other minor undesirable constituents from iron ore will provide both quality and cost benefits to the iron and steel producers. Development of future iron ore production in North America will face stiffer technical challenges. These new and undeveloped iron ore deposits are largely oxidized (non-magnetic) and by nature contain more slimes and other undesirable constituents. Unless other new technology evolves, flotation will be the major treatment process required to upgrade these difficult low grade iron ores.

Jan 1, 1993

By S. B. Bealko

Mining haul trucks comprise the majority of the equipment used in underground limestone mining operations and are known to emit high levels of noise. A previous study conducted by the National Institute for Occupational Safety and Health (NIOSH) indicates that 70-90 percent of all miners have a noise-induced hearing loss (NIHL) great enough to be classified as a hearing disability by retirement age. These results demonstrate the public health need to protect the hearing of workers in the mining industry, including haul truck drivers. ng of workers in the mining industry, including haul truck drivers. Cab enclosures present an opportunity to isolate the haul truck operator from both truck and other noise in the mining environment. A total of twenty-five haul truck cabs were studied which were divided into three style (treatment) categories determined by soundproofing features and technology for noise reduction: old-, new-, and retrofitted-style. This study examines the contribution of cab acoustics, operator performance, and maintenance to noise reduction for each cab style. Dosimeters were used to measure 8-hr time weighted average sound pressure levels (TWA8 SPLs) inside and outside the cabs to determine if different acoustical treatments affect cab attenuation. Adherence to the Mine Safety and Health Administration (MSHA) Permissible Exposure Limit (PEL) of 90 dB TWA8 (with a 90 dB threshold) was used as the main indicator of overall noise reduction achieved. Dosimetery results indicate only 2% of the samples exceeded the PEL, but samples could still be reduced much further. Descriptive and comparative statistics indicate that noise levels inside the new-style cabs are significantly lower than the other two cab styles. Also, data suggest that there is no difference in noise exposures when comparing the old-style to retrofitted cab styles. Operator influence (opening doors and windows) was a significant factor for increasing noise exposure. This paper demonstrates that properly designed cabs can achieve major noise reductions, but noise levels could still be reduced much further below the MSHA PEL. New-style cabs, equipped with modern noise-reduction treatments, exhibit much lower noise exposures than the other two cabs styles, and the effectiveness of the current noise-reduction treatments for retrofitted cabs is questionable. Haul truck driver observations indicate that improved noise exposure reduction training is needed. Finally, specific targets for future noise reduction research are suggested that will further contribute to the prevention of hearing loss for haul truck operators.

Jan 1, 2008

By T. W. Flemal

Good afternoon gentlemen. To begin, may I say ?thank you? to the AIME for the invitation to be here today to talk about my company's experience with shovel, truck, pocket, to car loading. The other author of this paper is here today. (Introduce John Sweet). Before we get to the details of this paper I want to tell you a little about Erie Mining Company. Erie Mining Company is located on the east end of the Mesabi Range in northern Minnesota and is engaged in the business of processing taconite rock into iron ore pellets. In 1970, the twelfth year of production, Erie will produce its rated capacity of 10.3 million tons of high grade iron ore pellets. The plant is the first of five iron ore pelletizing operations managed by Pickands Mather & Co. with a combined annual production capacity of 21 million tons. This plant began producing high grade iron ore pellets in 1957 placing it among the earliest of taconite production facilities in North America. Historically Pickands Mather & Co. had been a leading natural ore mine managing firm in the Great Lakes region for more than 70 years. Pickands Mather & Co. moved into the new field of taconite mining and processing with management and operational experience from the open pits and underground mines. We were to learn much of volume taconite handling requiring new equipment and new procedures. A trial and error period through the early years of taconite processing developed through the operation of an experimental sized preliminary plant near the present Erie Mining Company site.

Jan 1, 1970

By A. G. Mayton, L. Adler

The paper under discussion provides an excellent and concise study of compartment ergonomics for thin seam equipment. However, in accomplishing this, some very important operational aspects were ignored. Since these are likely to be determinant, the authors' response is solicited. The novel shuttle car with its cross-car, end-mounted compartment is operationally very different from the current one. The latter can be considered a highly mobile extension of the continuous miner or loader, with a pass-through conveyor, dump boom, and extra storage. As such, the vehicle's kinematics are the simple "I," or shuttle pattern, bent for going around pillars, with an intermediate stop at the "change-out point" (Adler, 1986 ). The action of the cable reel adjusts well to this pattern. The proposed shuttle car's motion either superimposes a "Y," time is lost (5 seconds) for each cycle, space is needed, line of sight is compromised, and a cable anchor is probably required at the dump. A chute is almost prohibitive in construction time and cost. The lack of a dump boom further curtails flexibility in the proposal. The value of a standard hand and opposite standard hand configuration also needs consideration. Many front-end loaders have a rocker (overshot) capability that is designed to achieve an "I” pattern. And crawler loaders sometimes use a side dumping bucket variant for the same purpose. These examples indicate the pattern's importance. For underground, thin seam application, the ram car has become popular. This is an articulated truck, battery-powered, and with an ejector dump. Its operational patterns would be similar to the novel shuttle car, except without the loading flexibility provided by a conveyor. Since the cab location of the proposed shuttle car largely obviates some of the major advantages of the present shuttle car, the question arises whether this configuration could be adapted to the current ram car and scoop

Jan 1, 1991

By C. A. Fleming, C. J. Ferron, P. T. O'Kane, D. B. Dreisinger

The platinum group metals (PGM's) are typically recovered by flotation, smelting of the flotation concentrate to matte, and matte leaching. Concentrates too low grade to be processed economically by the conventional process require a new treatment route. PLATSOL, a new pressure leach process, was developed for the Northmet deposit and dissolves in one step base and precious metals (PGM's and gold). Various options exist to recover all pay metals from the leach liquor. The preferred option to date involves a solid-liquid separation, followed by sulphide precipitation of gold and the PGM's, and copper solvent extraction using commercial solvent extractants. This paper briefly summarises the process and the effect of the main leach parameters. Application of the PLATSOL process to various feedstocks is also presented.

Jan 1, 2000

By Randhir S. Sehgal

After some decades of lying low and being treated as a second rate fuel, coal is back in the news. Production is rising. Predictions are for an ever expanding use, and they differ only in their rates of increase. Even the FBI is involved in trying to stop fraudulent sales of non-existent coal lands and leases to the innocent. In short, we have a nearly chaotic boom on our hands. Obviously our energy production base is in the process of undergoing a major shift, and the process will present many problems. However, there is little doubt that the industry has the basic strength and organization to be able to deal with the new issues that will arise as a result of these shifts in production and use of coal. After all, it does produce nearly 800 M tpy now, and coal is the single biggest fuel for generation of electricity. This role of coal is illustrated in the table below, which shows the coal equivalent quantities of various fuels used in the production of electricity.

Jan 1, 1980

By Thomas E. McNider

On July 20, 1990, a Spontaneous Combustion Control Plan was approved by MSHA for Jim Walter Resources, Inc. No. 5 Mine. The mine operated under the plan for twenty-nine shifts before MSHA revoked the plan. A total of fifty-five seals were constructed during the process of implementing the plan. The major difficulty in applying the control concept resulted from problems controlling leakage at the numerous seals. The number of seals was a direct consequence of attempting to merge the traditional bleeder system, used in all the Blue Creek Mines, with the bleederless system Jim Walter Resources proposed as a means of controlling the spontaneous combustion hazard. This paper discusses Jim Walter Resources experience with spontaneous combustion control and the new safety standard which applies to underground coal mines that demonstrate a history of spontaneous combustion and how this standard would apply to our No. 5 Mine. The new Ventilation Standards were published in the Federal Register on May 15, 1992, and scheduled to go into effect August 16, 1992.

Jan 1, 1993

By Paul D. Tavares, John Forbes, Eric R. Drooff

As the existing major U.S. - Canada rail tunnel was too small to accommodate double-stack container cars, Canadian National Railways is constructing a new parallel tunnel with a 50% greater diameter. Starting in Sarnia, Ontario, the new shallow-cover bored tunnel runs under a large research building and several other structures in an oil refinery before travelling under the St. Clair River. Maximum predicted settlements to be caused by the 9.2 meter diameter earth pressure balance TBM in the soft St. Clair till were in excess of 100 millimeters. As such, these settlements had the potential to cause severe damage and disruption to the existing refinery. In order to reinforce the soft clays below the refinery research building and other structures, and to compensate for settlement caused by the tunnelling, the ground improvement method of Soil Fracture grouting was successfully applied for the first time in North America. This paper will describe the details of both the soil fracture grouting application and the elaborate electrolevel remote monitoring system used.

Jan 1, 1995

By J. R. Caylor

The Mine Safety and Health Administration (MSHA) advanced several initiatives last year to further protect miners' health. Regulatory efforts included the implementation of a Hazard Communication rule for all mines, work on the Single Sample rule for all coal mines, and the Plan Verification rule for underground coalmines. Development and application of new technologies are actively encouraged in preventing miners' hearing loss and respirable dust overexposures. MSHA's successful x-ray program for screening of black lung among coal miners completed its third year. Compliance Assistance efforts are focused on Best Practices, outreach, and technical support for operators' specific challenges.

Jan 1, 2003

By John W. Harshbarger

The Upper Santa Cruz Groundwater Basin lies in the drainage area of the Santa Cruz River in Arizona, and extends upstream from the community of Rillito to the international boundary, see Figure 1. The principal water use area lies between and includes the cities of Tucson and Nogales. A subsurface geologic barrier near Rillito provides a reasonable dividing line between the groundwaters of the Upper and Lower Santa Cruz Basins. The Upper Basin contains the Tucson and Sahuarita-Continental critical ground- water areas. The Tucson Water Use Area encompasses the Tucson metropolitan area and extends from the northern boundary of the Basin south to the boundary between the Tucson and Sahuarita- Continental critical groundwater areas near San Xavier. The San Xavier Use Area is the San Xavier Indian Reservation. The north and south boundaries of the Continental Use Area coincide with the limits of the Sahuarita-Continental critical groundwater area. The first study of groundwater in this valley was initiated by Dr. G. E. P. Smith in 1905 and the results were published in 1910, followed by a series of bulletins of the Arizona Agricultural Experiment Station, University of Arizona, covering the general field of groundwater development and utilization. Beginning in 1939, the Ground Water Branch of the United States Geologic Survey, in cooperation with the Arizona State Land Department and the Arizona Water Commission (AWC), have published a series of bulletins concerning groundwater occurrence and utilization in various areas of the state. In 1975 and 1977, the AWC published the "Arizona State Water Plan" (1), comprising a detailed inventory of water availability and use in the State of Arizona, and a study of alternative futures.

Jan 1, 1979

By Thomas H. Koenning, William E. Bruce

The importance and complexity of the ventilation systems in many underground coal mines necessitates the use of digital computers to model the ventilation networks. The modeling procedures used by the Mine Safety and Health Administration (MSHA) utilize the MSHA-modified Penn State computer program. The basic techniques used by MSHA have been described in detail in NESA (now MSHA) Informational Reports 1066 and 1183 (1. 2). Two basic methods are utilized for modeling underground mine ventilation systems. The first modeling method is the use of actual air-flow, pressure, and fan-performance data acquired during a full air-pressure, air-quantity ventilation survey to develop a mathematical model of the ventilation system. The second modeling method is the design of a ventilation system using data obtained from calculation, from past experience, or from technical literature. The latter method would typically be used to design a ventilation network prior to developing a new mine. Regardless of which method is used for modeling, there is a need to know, or to calculate, appropriate resistance values to be used for airways and for the various ventilation control structures. Such data is typically difficult to obtain and this report is an attempt to summarize typical resistance values which may be used in designing ventilation networks for new mines or in simulating proposed system changes in existing mines. Illustrations are presented to show where some of the resistances typically are located and how they are modeled in mine ventilation net- works.

Jan 1, 1987

By F. Chavan

1. Introduction The new Cleuson-Dixence development project in the Valais region of the Swiss Alps, involves the construction of a new link between the Grande-Dixence dam (still world recordholder with a height of 300 m) and a power house on the banks of the Rhone consisting of approximately 20 km tunnels and shafts, and involving a fall of about 1900 m. This 1200 MW project will replace an existing 900 MW structure built in the 1960s, no longer considered efficient. The new project comprises a head race drift about 15.8 km long, a surge tank, an inclined cascade shaft 4,2 km long, and an underground power station. The work for lots C and D (head race drift from Tortin to Tracouet, surge tank, six adits ans the complete inclined shaft) was awarded to our group (Prader, Locher, SELL, Losinger, Evéquoz, Dénériaz, Imboden and Bouygues). The geological conditions are: Lower part of the shaft (300 m) : sedimentary - sandstone and soft tertiary sandstone. Middle and upper part (2600 m) : metamorphic - upper and lower carboniferous, interrupted by triasic chipping. The horizontal section (7 km) consists of mica

Jan 1, 1995

By J. Lovering, H. Wilhelm, P. Siewert

Introduction The Afton property is located 290 km (180 miles) by air east-northeast from Vancouver and 14 km (8.7 miles) west of Kamloops, a city of 60,000 people, in south central British Columbia, Canada. The mine is adjacent to the Trans-Canada Highway at an elevation of 670 m (2198 ft) above sea level. The ore body is a porphyry copper deposit that has undergone supergene alteration. The major economic minerals in the supergene zone are native copper and chalcocite with chalcopyrite and bornite in the hypergene areas. The grade is 1% with an overall copper distribution - 70% native, 25% chalcocite, and 5% chalcopyrite with bornite and covellite. The ore also contains important but variable amounts of gold and silver. The mill was designed to treat 6350 t/d (7000 stpd). Semiautogenous grinding was selected to minimize capital cost and because of the expected high clay content of the ore, which would have caused problems in a conventional crushing and screening plant. Test work indicated that a recovery of 87% was possible in a circuit incorporating both flotation and gravity separation. Flowsheet Run-of-mine ore is crushed in a 1.06 x 1.65-m (3.5 x 5.4-ft) Allis Chalmers gyratory crusher set at 228.6 mm (9 in.), closed side setting. The surge pocket, below the crusher, is emptied by a Hydrastroke feeder onto number one conveyor, which discharges onto a 180,000-t (198,416-st) coarse ore stockpile. Six Hydrastroke feeders on two conveyors withdraw the crushed material from the bottom of the pile. These two conveyors, in turn, discharge onto the belt feeding the semiautogenous mill. The live storage in the stockpile is approximately 22,000 t (24,250 st), sufficient for three days' mill feed. Primary grinding is accomplished in an 8.5-m (28-ft) diam by 3.7-m (12-ft) long Koppers (Hardinge Cascade) mill (Fig. 1) containing a 10% ball charge and driven by a 4000-kW dc variable speed motor. The mill dis¬charge is pumped by a 10 x 12 G.I.W. pump to a 1.22 x 4.88-m (4 x 16-ft) stationary screen sloped at 20°. Screen oversize returns to the semiautogenous mill (SAM), and the undersize flows by gravity to the ball mill discharge pump box. Secondary grinding is performed in a 5-m (16.4-ft) diam by 8.84-m (29-ft) Koppers overflow ball mill driven by a 3430-kW synchronous motor through an air clutch. The mill is in closed circuit with a Krebs Cyclopac containing 10 635-mm (25-in.) cyclones and the cyclone overflow, at 35% solids and 65% to 70% -200 mesh, is flotation feed. In order to limit the buildup of native copper, circulating in the secondary grinding circuit, a portion of the underflow from the cyclones is processed in a circuit containing screens, cyclones, and shaking tables to produce a finished metallic copper concentrate. Primary mill variable speed drive The overall waste to ore ratio at Afton was 4.5:1. The mining was to be done with only three shovels, which meant that it was highly unlikely that more than one of them would be in ore at any one time. The resulting inability to blend the mill feed made it impossible to prevent wide swings in the grade and grindability. The variable speed do drive motor installed on the semiautogenous mill was selected because of the extreme variability of the Afton ore body. This variability has persisted throughout the lifetime of the mine. There are times, however, when due to ore conditions, the mill is operated at full speed (78% of critical) for extended periods of several shifts duration. There are other times when the mill speed may be changed several times in a 12-hour shift due to changing ore conditions. When ore is processed that contains a fairly large proportion of fine native copper, the primary mill speed and, consequently, the tonnage may be reduced to improve the secondary grind and to maintain an acceptable grind and recovery. High clay ores require less mill speed and more dilute grinding densities. In the latter case, the slower primary mill speed also helps to minimize damage to the mill liners. Approximately 57% of the time the mill operates between 90% and 100% of full speed or between 71% and 78% of critical. The variable speed is also used for inching during mill relines.

Jan 1, 1987

By M. McPherson, G. Danko

Methods of measuring in situ rock thermo-physical properties are rapidly evolving. Among those existing in the literature, a particular measurement procedure was selected for further development. The measurement is based on creating a spherical temperature field in a drill hole using a point source heater of constant heat flux. The bivariate temperature distribution 0 (r, t) is measured at several points along the length of the drillhole, radius r from the heater and at particular time intervals (t). A number of different evaluation methods were tested for calculating the unknown thermal conductivity (k) and diffusivity [] from the measured temperature and the known heat flux. The results showed that evaluation using the finite difference scheme and small temperature differences measured at points close together, cannot give a reasonable result. In order to solve the problem a new general analytical evaluation method is developed. Using an appropriate technique, it is possible to simultaneously obtain values for k and [], incorporating a semi least square technique to reduce the uncertainty in the evaluation. The new device and evaluation method makes it possible to obtain from a single drill hole highly precise k and [] values within an 8 hour period. The method has been used in several underground mines in the U.S. with good results.

Jan 1, 1987

By Barton Kelby Cross

In the early 1960's the feasibility of mathematical modeling was demonstrated in Northern Rhodesia and southwestern United States, where techniques were developed to use these models in a new approach to aid engineers in the estimation of ore reserves, mine designs, and financial evaluations. These rudimentary models closely followed the manual methods, producing ore reserves and production schedule estimates that were as accurate as the manual methods, yet were many times faster. Mines evaluated and designed using these new tools gradually came into operation during the 1970's and entered the phase at which production scheduling and ore-grade control became day-to-day problems. Management expected the number of operational engineers to be small because small planning engineering staffs had produced the original designs and operated the smaller high-grade pits. Unfortunately, the tools needed by the mine engineer to perform short-term production scheduling and ore-grade control were labor intensive; they had not yet been generally computerized. Several attempts to use the original or exploration model for these two functions were futile. While an exploration model based on data from exploration work proved sufficiently precise for overall mine design and long-term production scheduling, the model lacked the precision required for short-term scheduling and grade control.

Jan 1, 1979

By L. D. Cruz

In Exxon's Los Bronces Expansion Project in Chile, a stochastic simulation is performed to resolve the complex decision problem of matching the mine to mill system capacities from both technical and economic standpoints. The unique combination of weather conditions at the mine and the 30-km belt conveyor network for ore transport to the mill necessitates this analysis in the planning phase to optimize the design capacity of the sys tem. Appropriate statistical distributions of major equipment performance, snow storm duration, power outage, etc, ate developed from actual mine local records and manufacturers specifications. The interactions of operational constraints including ore storage capacities, number and sizes of individual equipment, ore variations, and mine and mill production rates are studied more realistically than in a traditional planning approach. Details of the computer modeling and typical results of simulation studies are discussed.

Jan 1, 1981

Production reporting is a natural computer application and is often one of the first applications implemented by new computer users. Automation of a manual reporting system is a good place for new computer users to gain computing experience because generation of basic reports - is fairly straightforward, and automation can often be justified easily on the basis of clerical cost savings. Computers are particularly well-suited for reporting applications which generally satisfy the criteria for effective computerization. Three characteristics must be present to effectively utilize a computerized system: 1) The potential application must be precisely definable. If an algorithm for data processing cannot be developed, data cannot be processed. 2) The operation to be performed must be repetitive. If a particular function is only going to be performed once, computerized systems development is probably not justified. 3) The volume of the data to be processed must be relatively large. If only a few items of data must be manipulated, manual methods are probably adequate. Although a computer can perform only a few functions (it can compute; it can make comparisons; it can rearrange data), it can perform these functions much faster and more accurately than a human being can. The ability to classify and reclassify data in a variety of ways and the ability to summarize data make the computer an ideal tool for production reporting. Production reports can be classified into three major categories, depending on their purpose. Reports can be used for (1) informative, (2) analytical, and (3) control purposes.

Jan 1, 1979

By Charles H. Grant

Blast design methods generally deal with end points or limits of design such as spacing, burden, stemming depth, etc. Even cratering design deals with limits defined as a function of energy decay to a limit. Although this crater method provides a better method than trial and error judgment it does not take into consideration the distribution of energy throughout the material to be blasted. This paper deals with a method of examining this distribution with the aid of a computer and how changes in blast design affect this distribution. First I would like to explain the equation used to develop the energy summations throughout the blast. As shown in Figure I a series of drill holes are drilled to various depths starting by placing the explosive charge on the surface and then at various depths until a sufficient depth of hole is reached to exceed the ability of the explosive energy effect to reach the surface of the ground. All volumes of explosive are the same, all holes contain the same explosive and the drill hole diameter is the same.

Jan 1, 1980