Search Documents

By Maria S. Adusmilli, Bhaskara A. Rao, Jorge G. C. Barros, Augusto F. Mendonca

Lateritic gold has been the object of study only for a very few years, though nuggets have been mentioned in earlier works even as early as 1984 by Hartt in Brazil. In Mato Grosso State, lateritisation is intense, as is common in all tropical forest areas of the world. Exploration has revealed the presence of recoverable "nugget gold" of variable sizes (30 - 200 gms) but frequently of good size (0 - 40 gms), especially near Cuiaba and Alta Floresta regions. In both of them the host system is a lateritised breccia indicative of a fault or shear zone breccia, though in different lithological domains. The Cuiaba occurrences are phyllitic and show a profile as follows, from top to bottom: 1) Compact ferralite crust. 2) Oolitic to pisolitic compact crust (+ some gold). 3) Mottled concretionary laterite crust. 4) Lateritised "eluvial material" (gold nuggets). 5) Mottled patchy to banded laterite. 6) Banded lateritised phyllite with lenticular to banded goethite. 7) Altered red goethitic phyllite, with quartz veins (+ fine gold). 8) Unaltered grey phyllite with quartz veins (Protore). The Alta Floresta-Juruena River occurrences are volcano-sedimentary and show a profile as follows: 1) Deep brown siltitic, argillaceous and arenaceous material with organic matter (+ gold). 2) Modular and concretionary laterite, compact and indurated, with arsenophyrite in quartz fragments (gold nuggets). 3) Band with silty-clayey matrix and arenaceous in nature. 4) Bedrock meta-arcosian arenite. 5) Volcano-sedimentary with rhyodacites and andesitic basalts, with intercalations of arkosic and greywacke nature. Breccias and quartz veins, and granites associated in different portions (Protore).

Jan 1, 1988

By George J. Karabin

Over the past few years, the use of fully grouted bolts to support the roof of underground openings has increased dramatically. While conventionally anchored bolts effectively reinforce the strata of over 80 percent of mine workings, the use of resin grouted bolts in areas of severe roof conditions has resulted in a substantial reduction in roof falls and an overall improvement in both safety and production. The Roof Control Group of Pittsburgh Technical Support Center, Mining Enforcement and Safety Administration, has conducted numerous field and laboratory investigations to isolate parameters which contribute to the effectiveness of both conventional and resin bolting systems. Specially developed strain-gamed resin bolts, compression pads and differential sag stations installed during the mining cycle have generated data reflecting the loading characteristics and resulting roof stability associated with each type of support. Additional investigations have produced optimum installation parameters of the two systems including the effectiveness of thrust/torque controls for conventional bolts and various bolt/ hole diameter combinations for fully grouted rods. Theoretical analyses, coupled with the actual field and laboratory findings and numerous installation observations have facilitated basic comparisons of the working mechanisms and failure modes of both resin and conventional systems.

Jan 1, 1976

By Colin C. Brooks

The Ok Tedi gold/copper deposit of almost 800 million tonnes was found in I968 because at that time technology had just developed sufficiently to enable exploration of such an area, world markets and prices for copper encouraged exploration for large deposits of low grade ore, Papua New Guinea law encouraged exploration by groups with men, money, management and expertise necessary for successful prosecution of such a search and such groups were already operating in the country.

Jan 1, 1990

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this work was to assess the influence of parameters such as residence time, solid content, and temperature in a process route towards purified rare earth liquor which could be adequate to produce marketable rare earth products. The steps of the process route proposed in this study comprised water leaching of a sulfated rare earth ore and removal of impurities through the purification of the rare earth sulfuric liquor, which is the product of the water leaching step. The sample used in the water leaching experiments was a sulfated rare earth ore produced by the reaction of a beneficiated rare earth ore with sulfuric acid followed by roasting at 700 °C for 2 h in a muffle furnace and cooling at 20 °C. The water leaching experiments showed that the best condition comprised a residence time of 30 min, temperature of 20 °C, and solid content of 10% w/w, resulting in a recovery of 71.3% of the rare earth elements (REE) and a lower impurity extraction, e.g., only 15.0% of Fe, representing the main impurity in the rare earth ore. Even when presenting low amounts of impurities, the rare earth sulfuric liquor still needed to be purified before it can be used in the production of marketable rare earth products. In the study, the rare earth sulfuric liquors were purified in two consecutive neutralization steps, first by dosing the limestone pulp to pH up to 3.5 and secondly by adding the lime pulp to raise the pH from 3.5 to 5.0. The application of two consecutive purification steps at 20 °C resulted in the highest overall REE recoveries (65.4%) throughout all the steps of the process, being 71.3% in the water leaching, 99.6% in the partial purification with limestone pulp, and 92.1% in the purification with lime pulp at 20 °C. Under this condition, there was a total elimination of Fe, P, and Th and a significant reduction in the Al, U, and sulfate concentrations in the purified rare earth liquor. The purified rare earth liquor attained through the experiment is expected to be amenable to be used in the production of marketable products due to the lower impurities/REO mass ratios.

By Robert Dunne, John Angove

The physical properties of an ore body require determination for virtually all mining projects, new and existing. The extent and regularity of such determinations being subject to the size and homogeneity of the orebody. Such properties have an impact at the design stage of new plants, with respect to equipment specification, and thus effects capital costs; and also impacts on the operating costs of new and existing plants, with respect to power consumption, production levels and part replacements. All of these can severely alter the bottom line and can be the determining factor in the economic viability of many projects. This paper examines some of the most common properties that are measured, the procedures utilised in determining these properties, and their variability under conditions of reproducibil­ity, and to a lesser extent repeatability. The properties looked at were Impact Crushing Work Index, Abrasion Index, Bond Rod Mill Work Index and Bond Ball Mill Work Index. A number of testing laboratories throughout Australia and the US were utilised in the survey. The results showed up some interesting and important features of the procedures used, all of which have become accepted industry standards, and which had varying effects on the final result. Tests such as the rod and ball mill indices would appear to have reasonably robust procedures which allowed for the determinations of the respective index without the introduction of significant variations, although there were indications that variations could occur. The other tests gave a sufficiently different picture to be able to suggest that an argument could be made for a more intensive investigation to be undertaken, with the possible outcome that a modified test procedure or an alternative test is required.

Jan 1, 1997

By A. C. Nixon, A. D. S. Gillies, Hsin Wei Wu

Ventilation and refrigeration strategies for the 3000/3500 orebodies, Mount Isa Mines, Australia were reviewed. The orebodies lie between 1,200 and 1,800 m below surface and are characterised by steep geothermal gradients, intensively mechanised stoping methods and high ambient air temperatures in summer. Providing acceptable working conditions under these situations is difficult and costly. The ventilation air quantity required in the 3000/3500 orebodies exceeds 550 m3/s when the production rate is greater than 2.5 million tonnes per year. The maximum quantity that can be supplied and exhausted using the existing intake and return ventilation system is estimated at about 630 m3/s. For production rates greater than 3 million tonnes per year, either new intake and return airways will need to be developed or innovative approaches such as controlled partial recirculation used. A description is given of technical and economic investigations conducted at Mount Isa into controlled partial recirculation. During these investigations, a major field trial of a controlled partial recirculation system was undertaken with results indicating that an acceptable working environment can be achieved practically and economically utilising this approach. The cost involved in controlled partial recirculation for supplying the required ventilation quantity when the production of 3000/3500 orebodies exceeds 3 million tonnes per year is examined. A cost comparison between recirculation and other conventional alternatives such as new surface shaft or underground booster fans is included. The results indicate that the option of a new surface shaft will incur a high initial capital cost and moderate annual operating costs. The alternative of underground booster fans will necessitate a moderate capital cost and very high operating costs. Controlled partial recirculation, in this case, offers both the lowest capital and operating costs of the three options evaluated.

Jan 1, 1995

By Stuart M. Lipofsky, Norm Hutchins

The Metropolitan Water District of Southern California has undertaken the Lake Mathews Outlet Facilities project to replace the existing outlet facilities. In the late1990s, consulting engineers for the District determined that the Lake Mathews Outlet Facilities were susceptible to a catastrophic failure during a seismic event. To ensure a reliable supply of water to Metropolitan’s customers in the Los Angeles area, the District decided to construct new outlet facilities. This Project consists of excavating a large diameter junction shaft, a 6.10 m (20 ft.) horseshoe tunnel, three short 4.88 m(16 ft.) horseshoe bypass tunnels, and a large excavation within a cofferdam that were all driven in difficult rock conditions. Additionally, a new concrete outlet tower was constructed and connected to the existing tunnel by the new bypass tunnels and through the junction shaft. The J.F. Shea Co., Inc. of Walnut, California, is currently finishing the construction of the Lake Mathews Outlet Facilities Project for Metropolitan. The large diameter junction shaft is 50.60 m (166 ft.) deep, excavated 16.15 m (52 ft.) in diameter and lined with a61 cm (2´-0?) thick steel reinforced concrete lining to a finished diameter of 14.63 m (48ft.). The shaft was excavated full face with one stationary shaft three-boom jumbo, modified for the large diameter. The shaft also consists of four sets of gate guides extruding from the shaft wall towards the center of the shaft that provide the ability to operate up to four mechanical gates at any time, to open or close each tunnel. This paper will present the junction shaft excavation and concrete construction techniques, including the innovative slip form method utilized to construct the junction shaft.

Jan 1, 2003

The concept of "classification is expanded beyond the performance of the classifying equipment to include all aspects of the fines removal system of the grinding circuit. Design and operating parameters which affect fines removal are identified and discussed, and a quantitative index for circuit fines removal effectiveness is defined. This approach lends new interpretation to certain observed phenomena, and suggests useful guidelines for circuit design and operation.

Jan 1, 1985

By D. Panias

Alumina hydroxides such as gibbsite (Al(OH)3) and boehmite (AlOOH) are precursors of many types of alumina that find important industrial applications. The thermal decomposition of AlOOH, which is a more energy saving precursor compared to gibbsite, gives rise to the formation of ?-, d-, ?- and a-aluminas that are used for the production of catalysts. The applications of the aluminas are governed by their properties that are a function of the precursor material and its microstructure. The microstructure in turn is a factor of the method and conditions applied, as well as, in the case of soft chemical processes, on the anions present. Towards these ends, this study was focused on the effect of different anions on the physicochemical characteristics of the alumina hydroxides precipitated in the first 5 minutes after the perturbation of the stability of a supersaturated sodium aluminate solution (Bayer liquor).

Jan 1, 2006

By K. J. Reid, I. Iwasaki, T. Sabelin

Introduction Occurrences of platinum group minerals (PGM) in mafic and ultramafic rocks in association with Cu-Ni mineralization are well known. Yet for the Duluth Complex, a large body of dominantly mafic igneous rocks in northeastern Minnesota with significant Cu-Ni mineralization (Bonnichsen, 1972; Boucher, 1975; Watowich, 1978; Weiblen and Morey, 1980), little has been published concerning its platinum group element (PGE) contents and mineralogy. In a previous study of massive sulfide rock, sperrylite (PtAs2) was found in nickel arsenide and recovery of arsenide minerals by flotation has been investigated (Iwasaki et al., 1986; Ryan and Weiblen, 1984). Recently, an announcement was made of the discovery of significant quantities of platinum and palladium [peak assay values of 9 g/t (0.27 oz per st)] in an interval of a drill core with disseminated sulfide mineralization 16 km (10 miles) southeast of Ely, MN (Anon, 1985; Sabelin, 1985). This paper describes PGM from the Pt-Pd-enriched zone and evaluates their potential for concentration. Geologic setting The Pt-Pd zone occurs in the South Kawishiwi in¬trusion near its basal contact at 734 to 737 m (2408 to 2418 ft) depth. The South Kawishiwi is one of several minor mafic intrusions that constitute the western margin of the Duluth Complex near Ely, MN (Fig. 1). It is com¬prised of a 70.1- to 350.5-m (230- to 1150-ft) thick sul¬fide-bearing basal unit of troctolite with minor amounts of anorthosite, norite, picrite, and oxide layers overlain by a troctolite unit with interlayered anorthosite (Bonnichsen et al., 1980; Foose, 1984; and Foose and Weiblen, 1986). The basal unit, in which the Pt-Pd zone is found, is markedly heterogeneous in rock type, lacking any coherent internal stratigraphy, and shows evidence of both pre- and post-consolidation faulting (Foose and Weiblen, 1986). Geochemistry Chemical analyses were made on 0.3-m (1-ft) intervals of crushed drill core material (1/4 core, BX size) at 731.5 to 740.7 m (2400 to 2430 ft) depth and the results are presented in Fig. 2. The analytical techniques used were atomic absorption spectrometry for silver, chromium, copper, and nickel; a coulometric titration method for sulfur; and a combined fire assay-DC plasma technique for gold, palladium, and platinum. Figure 2 shows the significant enrichment of platinum and palladium at 734 to 737 m (2408 to 2418 ft) depth; it corresponds to a stratigraphic interval rich in oxide minerals. Average values for platinum and palladium contents over the 3-m (10-ft) interval are 2520 and 2580 ppb, respectively, or 5.1 g/t (0.15 oz per st) platinum plus palladium. Platinum plus palladium contents from individual 0.3-m (1-ft) intervals are as high as 9120 ppb or 9.1 g/t (0.27 oz per st) and average 7.4 g/t (0.22 oz per st) in a 1.5-m (5-ft) interval in the richest part of the zone. The Pt-to-Pd ratio is nearly 1:1 over the entire 9.1-m (30-ft) interval and the platinum and palladium correlate closely with chromium, which ranges from 1.9% to 5.3%. Copper, nickel, and sulfur contents for the drill core interval are also given in Fig. 2. In¬terestingly, the Pt-Pd high corresponds to a depletion in copper, nickel, and sulfur. Mineralogy of the Pt-Pd zone The Pt-Pd zone occurs within an oxide-rich zone or layer that consists essentially of oxide minerals, plagioclase, and olivine. The oxides may constitute as

Jan 1, 1987

By R. Todd Swinderman

Impact cradles are installed below the belt in conveyor loading zones to cushion the forces from material loading. In this paper, the author will discuss the need for and then explain the new CEMA standard for engineering of impact cradles. He will review the engineering theory and work through an example to demonstrate the assumptions used in the standard do not inappropriately affect the CEMA rating system.

Jan 1, 2002

By Y. Nan

A new computer simulation model for the analysis of underground coal mine production systems in the Peoples Republic of China is presented. As a case study the model was used to analyse the railway system of an existing underground coal mine. Some results of this first application are given in this paper and some conclusions of common interest for underground rail haulage systems are discussed.

Jan 1, 1986

By S. Nunoo

The shape of particles has a significant effect on the shear strength and deformational characteristics of granular materials. Weathering can change the grain shapes. For example, more weathered sands tend to be rounder regardless of particle size. Particle shape analysis was performed on samples collected from the Questa mine rock piles, a debris flow and the pit alteration scar. In order to increase the validity of the particle shape analysis, 4 persons including 2 geologists and 2 mining engineers were involved in describing the particle shapes. The results of this analysis indicate that rock fragments in the collected samples are mainly subangular, subdiscoidal and subprismoidal. The sphericity and angularity of the rock fragments of the older analogs are similar to those of the rock piles. This suggests that short-term weathering (<100 years) has not noticeably changed the particle shapes at the test locations. Rock piles made of more angular particles are more stable compared to rock piles with rounded particles.

Jan 1, 2009

By Brian Fulcher, John Eastlund, J. B. Copeland

Following the completion of the 7,600 m primary access tunnel by Kiewit/Parsons Brinckerhoff (K/PB) in April 1997, an exploratory East-West Cross Drift Tunnel was constructed at the Yucca Mountain Project over the proposed future repository block for high level nuclear wastes. The 2,681 m (8,796 LF) East-West Cross Drift Tunnel was excavated through volcanic tuffs having zones of incompetent rock using a re-built Robbins 5.000 m (16’-5”) hardrock TBM with a special arrangement of supporting equipment. Details of the unusual site and contract conditions will be discussed as well as with the unique tunnel equipment specified by the Owner. This portion of the Yucca Mountain project required eight months to complete.

Jan 1, 1999

By P. Randall, J. Ickes, S. Chattopadhyay

This study was undertaken as a part of developing treatment alternatives for waste materials, primarily waste rock and roaster tailings, from sites contaminated with mercury (Hg) mining wastes. Leaching profiles of waste rock over a range of different pH and oxidation-reduction (Eh) conditions were performed. Since iron (Fe) is present in large quantities in mining wastes, the effect of Fe on leaching of Hg was also determined. Results show that the Hg concentration increased as the pH of the suspension increased until a pH value of 10.65. Thereafter, the Hg concentration decreased sharply. The Hg concentration, in presence of Fe decreased significantly (1/10thto 1/100th). Kinetics results show a relatively slow rate of leaching in presence of ferric ions. The results obtained from the present study are being used to predict the fate and stability of Hg present in the environment, and will therefore, be useful in dictating the nature and suitability of any remediation treatment.

Jan 1, 2003

By Q. Xu

The new process consists of the selective coalescence of fine hematite particles by fine magnetite. The gangue minerals are dispersed by some dispersant; thus it can be separated by desliming. This process is particularly suitable for fine-grained hematite/magnetite-type deposits.

Jan 1, 1989

By M. J. Virnig, Christopher A. Fleming

THE CIP PROCESS "IN THE RIGHT PLACE AT THE RIGHT TIME? After its tentative introduction to the precious metals mining industry in the earlier part of this century, the carbon in pulp (CIP) process has now come of age, and is the process of choice on all new gold mills. Well over 50 percent of all gold that is mined each year is recovered by adsorption on activated carbon, and the percentage will increase in the years ahead, when old mills using Merrill Crowe technology come to the end of their lives, and as the proportion of world gold production from low-grade resources increases. The pioneering process development work in this field, which was mainly concerned with carbon elution, was carried out by Zadra and his colleagues at the United States Bureau of Mines in the early 1950&apos;s (Zadra et al., 1950, 1952), and led to the commissioning of the first large-scale, industrial CIP plant, at the Homestake Mine in South Dakota, in 1973 (Hall et al., 1974). From there, the process spread rapidly, firstly in South Africa in the late 1970&apos;s. and then throughout the rest of the gold producing world in the 1980&apos;s. There were several factors that led to the meteoric (by gold industry standards) acceptance and successful implementation of this new technology into gold processing operations worldwide. Firstly, and perhaps most fortuitously, the development of the technology closely paralleled the 1968 release of the gold price from the rigid constraints of the $35/oz. gold standard. With the value of the metal allowed, for the first time in modern history, to fluctuate in response to free market supply and demand forces, the gold industry witnessed an unprecedented boom as the price of their commodity increased ten-fold in a remarkably short period of time. This had several important spin-offs as far as new process developments were concerned: The profits realized by established gold-mining companies increased enormously and, consequently, there was more to spend on research and development and exploration for new deposits.

Jan 1, 1993

By Martin P. Schroeder

"Challenges have emerged as subway systems age and as new tunnels are bored in congested corridors or in high-risk environments. To help public transportation agencies address tunneling challenges, the American Public Transportation Association has convened numerous independent industry peer reviews composed of top experts in their fields to come together and provide recommendations and solutions. This paper provides case histories of peer reviews that include topics such as boring through toxic soils, boring underneath existing tunnels, retrofit of tunnel ventilation systems, and mitigation of water intrusion. Peer reviews are applicable to all tunnel projects worldwide. The paper will highlight the conditions of these challenges, peer review recommendations, steps taken to reach agreement, and the successes that resulted, which led to major changes, new legislation and reduction of risk. INTRODUCTION Public transit agencies face many challenges in maintaining and expanding safe transit operations, especially as systems age, ridership expands, and budgets remain flat. The development of new industry standards and federal safety regulations places further demands on transit systems, with compliance often taxing in-house resources. Studies of the state-of-good-repair across US public transit systems indicate a current backlog of $84 billion in maintenance projects, which will require an investment of $18.2 billion per year to eliminate the backlog by 2030[1]. Systems not in a state-of-good-repair may not operate efficiently, may not be available to meet the growing ridership demands, and may not meet required safety goals or reduction of risk. Innovation is another clear need transit agencies have for improving system performance and lowering operating costs.To meet these challenges, transit agencies often turn to industry peer reviews for guidance and recommendations as part of their overall strategy to maintain and grow the safe operation of their systems. As a service to its members, the American Public Transportation System (APTA) has developed an industry peer review program designed to give agencies opportunities to learn from each other and help them address challenges in operations, engineering design, and construction of their systems. Over the past 20 years, APTA has performed hundreds of peer reviews covering all aspects of transit system operations from fare collection to agency organization, project delivery methods to safety culture, and engineering design including tunneling and tunnel fire ventilation. As rail transit systems expand to meet increased ridership, it is often necessary to bore new tunnels for alignments in congested areas where surface rights-of-way are lacking. Such proposed alignments can pose significant challenges for transit agencies, as they contend with various tunneling problems."

Jan 1, 2016

By E. Baliktsis

PPC (Public Power Corporation) operates a new power plant at the South-West part of Crete. Recently the extension of the Power Plant started. ATHENA SA the main contractor of the project assigned to EXORIXI SA the implementation of a blast vibration monitoring program and prevention-evaluation of risks caused by construction blastings inside or very close to the operating part of the power station. The blasting parameters and characteristic elements that had been evaluated, the measures that had been taken and materialized, the overall risk management and the results of the whole program are presented in this paper.

Jan 1, 2006

By S. K. Das

A detailed strata-mechanics investigation and examination was carried out in the E2 Panel (ML-II/7) of the XVI Bottom coal seam, which is located in the Moonidih Colliery of B.C.C.L., Jharia coalfield, India. Above this panel, the XVI Top coal seam was previously worked out by a longwall panel. Based on intensive field study and on experiments in a number of longwall panels located within various Indian coal mines, the actual behavior of the coal roof strata was evaluated and new strata-mechanics concepts around the longwall panels were developed. These concepts resulted in new methodologies concerning the behavior of roof rocks, caving characteristics, etc. within longwall panels and in the area of strata mechanics. Based on these new strata-mechanics concepts, a very simple, but realistic, model was developed to determine the optimum capacity of the powered supports. This model considered the combined loads resulting from the detachment of strata and composite layer blocks from the face and, also, loads due to the deflection of strata and composite layers situated above the detached roof rockmass. This formula, along with the other related formulas by the author, prompted the determination of the optimum capacity requirement for the powered supports to be used in the XVI Bottom coal seam, located under the worked out area. This new concept in strata mechanics and capacity requirements of the powered supports in a longwall face may be an aid to Mining Engineers.

Jan 1, 1997