Search Documents

By Britta Schoesser, Zdenek Zizka, Markus Thewes

"The support pressure of a slurry shield corresponds to the in situ earth and groundwater pressure to ensure the stability of the tunnel face. The support fluid (bentonite suspension) penetrates from the excavation chamber into the pore space and transfers the support pressure to the granular structure of the soil within this zone. At the same time, the cutting tools rotate periodically with the cutting wheel and remove the penetrated soil up to a certain cutting depth at the face. Shortly after the tool passing, the penetration process starts again. Both, the support pressure and the soil excavation, act in the same direction at the tunnel face, but they are subject to different cyclic intervals. This relationship between the time needed for the transient penetration process and the interval of the cyclic passage of the cutting tools at a local point at the face is examined and the impact onto the global face stability is discussed. INTRODUCTION Slurry shields are usually deployed for excavations in soft ground. The main application range is in non-cohesive soils (DAUB Recommendations 2010). In non-cohesive granular soils, the tunnel face stability is one of the key design issues. The slurry shields make use of pressurized bentonite suspension (slurry) to support the unstable tunnel face. To support the tunnel face effectively, the slurry pressure has not only to counter the groundwater pressure, but also has to be transferred into an effective stress to support the soil grains. In general, the pressure transfer can be achieved in two ways: (1) with a thin flexible membrane or (2) a penetration zone. The membrane (1), called filter cake, creates a thin impermeable layer from bentonite particles directly on the tunnel face, and enables a transformation of excess slurry pressure into effective stress. In case of penetration zone formation (2), the excess slurry pressure is transferred onto the soil skeleton along the entire penetration depth by shear stresses between slurry and soil grains. These theories, presently applied to assess the pressure transfer on the grains within slurry shield tunnelling, are originating from diaphragm wall technology, e.g. Müller-Kirchenbauer (1977), Kilchert and Karstedt (1984). They assume that the support pressure transfer mechanism is built-up instantaneously on the whole tunnel face and is not damaged or influenced by the interaction with excavation tools. These assumptions are valid for conditions during the excavation of diaphragm wall trenches whose bottom is excavated and the walls of the trench are supported. At the tunnel face of a slurry shield, the support suspension acts on the same area as the soil excavation. Hence, the conditions on the tunnel face are transient (time dependent) due to the time period needed for the penetration process of the slurry and the periodical damage of the pressure transfer mechanism by excavation tools (Fig. 1a)."

Jan 1, 2016

By George P. Demopoulos, Vladimiros G. Papangelakis, Dimitrios Filippou, A. J. Monhemius, G. W. Warren, E. Peters

A new method developed for the estimation of the activity of Ht in mixed sulfate solutions is described and examples of application of this method to the system H2SO4-ZnSO4-FeSO4-Fe2(SO4)3 from 298 to 473 K are offered. The method makes use of an "extended Debye-Hiickel" type of equation that was originally put forth by Das for pure H2SO4 solutions at ambient temperature. The treatment of mixed sulfate solutions was made possible by combining that equation of Das with a speciation algorithm which calculates the abundance of all species formed. The developed method, which also takes into account ionic strength and temperature effects, was used to generate hydrogen ion activity and speciation data for all possible acid/metal sulfate pairs of the system H2SO4-ZnSO4-FeSO4-Fe2(SO4)3. Finally, under the light of the reported data, specific examples of hydrometallurgical reaction systems are analyzed in terms of thermodynamics or kinetics. In particular, the systems discussed are: hydrometallurgical precipitation of hematite, solvent extraction of Fe(III), acid leaching of zinc ferrite, and oxidation of Fe(II) to Fe(III) by O2(aq).

Jan 1, 1993

By D. G. Klaren

Self-cleaning fluidized bed heat exchangers are conquering the world for reason that they are able to solve any severe fouling problem in indirect heat transfer due to the circulation of cleaning particles through the tubes of vertical shell and tube exchangers. In most cases, these particles consist of chopped metal wire. Moreover, self-cleaning fluidized bed heat exchangers perform with excellent heat transfer at very low liquid velocities, which enables completely new designs of conventional shell and tube configurations. This article explains the principle and application of this self-cleaning heat exchange technology and also pays attention to an actual case of a revamp of the severely fouling exchangers of a conventional multi-effect evaporator into a self-cleaning configuration. Possibilities for the revamp of conventional exchangers suffering from massive and very hard scale deposits are found in a variety of metallurgical processes, such as: The refining of nickel, the production of alumina from bauxite and many others.

Jan 1, 2003

By Paul C. Lingo

The title of my talk today might lead you to two logical conclusions: The industry is faced with a problem that requires a solution and after discussing the problem I will offer a solution. The first conclusion is painfully accurate. One need only look at the accident statistics to be aware of the problem. During the eight-year period 1954 through 1962, the United States Bureau of Mines reports that falls of rock and coal accounted for 1,435 of the 2,516 fatal injuries that occurred in underground bituminous coal mines. Some improvement was made during 1962. For the first time since records have been kept, falls of rock and coal accounted for less than 50 per cent of the underground fatal injuries. The 105 deaths recorded in 1962 indicate that a great amount of work remains to be done in this area. As to the second conclusion, let me assure you at the outset that I have no panacean solution; however, I do propose to discuss some aspects of the problem and some possible methods of solution. What methods of solution are now, or have been employed in attempting to solve the problem? More specifically, what methods have you and your associates used? Has it been an orderly well thought out approach to the entire problem, or has it been a somewhat piecemeal approach which tackled the immediate problem and left the total problem for another day? Perhaps a new approach may be in order.

Jan 1, 1964

By M. H. Pettibone

During the past decade, the size of grin- ding mills has steadily increased. Mills 11 m in diameter with 9 mW motors have been installed with even larger units on the drawing board. The rising costs of energy and labor have spurred interest in improving efficiency while reducing capital investment and operating labor. Autogenous and semiautogenous grinding have experienced renewed interest as efforts to reduce operating and capital costs have increased.

Jan 1, 1981

By J. J. Bean

The development drilling program of the Copper Cities mine indicated that the molybdenum content of the ore would be about 0.011% MoS2' The molybdenum content of the Miami mine at the same time was about 0.025% MOS2' The Miami mill had a very successful molybdenum operation which used bleeder turbine steam from the Miami power plant for the steaming operation. The much lower grade of the Copper Cities ore, the absence of a source of low cost steam and the use of sodium aerofloat as the copper collector which Miami experience indicated did not respono readily to the steaming technique made very doubtful the success of a similar operation at Copper Cities. However, the relatively few pounds of copper that could be recovered from the low grade Copper Cities heads made very desirable the recovery of the molybdenwa,as a source of additional revenue. Accordingly, shortly after the Copper Cities mill began operation, a research program was instituted to develop a suitable method of molybdenum recovery. This program explored first, the successful steaming process then in use at Miami and as expected, found it unable to decompose the sodium aerofloat copper collector. The known chemical depressants were then tried without much encouragement. Finally the copper concentrate was dried, not roasted, to 2-3% mOisture and this along with sodium ferro-cyanide and cyanide resulted in sufficient copper depression that a final molybdenum concentrate containing 1.0% CU could be made. The bench scale testing was followed by pilot plant testing. Sixteen

Jan 1, 1972

By Emmanuel V. Manlapig

The variables involved in a complex process like flotation can be classified as follows: a. Disturbance variables - which are undesired properties of the process input which affect the value of the process output but which are not subject to adjustment. They are the result of changes in the properties of the feed, like changes in head grade, flow rate, fineness of grind, etc. b. Manipulated variables (sometimes referred to as process variables or control variables) -which are those that are adjusted - reagent addition, aeration, pulp level - in order to compensate for the disturbances in the properties of feed. c. Performance variables (sometimes referred to as controlled variables) -which are those whose values measure the performance of the process. They are properties of the process output such as grade and recovery. The function of a control system is to maintain the process performance equal to the control objective in spite of the disturbances by adjusting the manipulated variables. Attempts at developing automatic control systems for mineral processing operations date back to the thirties and in many of these attempts the results were not surprisingly poor and un-stable. The poor results brought indifference and suspicion towards automatic control on the part of operators and management. The reasons for the apparent failure of these attempts were two-fold: a. the lack of adequate understanding of the behavioural responses of the process from the control point of view, and b. the lack of reliable control instrumentation which could withstand the harsh environment in mineral dressing plants. Many operators had accepted the fact that control of mineral dressing could be best conducted manually. In the case of flotation circuits, control had been virtually based on the skill and experience of operators particularly their ability to identify and rectify poor flotation performance aided by results from the laboratory (chemical) analysis of regularly collected samples from strategic points in the circuit which are at best, hourly collected samples.

Jan 1, 1978

By Paul Soros

The Conneaut, Ohio, terminal of the Bessemer & Lake Erie Railroad was the first rail-to-ground-to-water coal terminal on the Great Lakes. Compared to the traditional method of holding coal in railroad cars at the ports for dumping their contents into vessels, it provided for: a. Immediate train turn-around independently of vessel arrivals. b. Winter storage of coal at the port, permitting year round shipment by the mines and year round operation of the railroad.

Jan 1, 1969

By E. Ilgar

Biodegradation of spodumene by Asnergillus niger has been investigated. This organism oxidizes sucrose to citric and oxalic acids (in approximately 50-sot proportions) which degrade the spodumene mineral. The kinetic effects of leach variables on the dissolution of lithium were determined. The maximum theoretically attainable rate of lithium extraction was calculated for the effect of pulp density, to be V : 3.01 x 10 kg m sand the corresponding constant value, K = 12.47% pulp density. The apparent activation energy of lithium extraction vas found to be ^E = 20.3 kJ and frequency factor A = 5.66 x 10 s for S-spodumene leaching by synthetic -3 citric and oxalic acids (each in 0.05 kmol m-3 concentrations).

Jan 1, 1989

By Chin Wei Yang

Linear programming (LP) has proven to be a most effective mechanism for modeling a vast array of practical problems, while the development of LP applications in engineering have been extensive enough to show its advantages and limitations. In this paper: we focus on the properties of the widely-wed linear programming transportation (LPT) model formulated and developed by Koopmans (1) . There have been many models of this type applied especially in the field of energy economics (2-7). Since most of these applications can be linked to the seminal work of Henderson (8), we stall present our discussions based on his work.

Jan 1, 1980

By B. A. Waite

The new OSH regulations concerning ground ward monitoring of underground coal mines has been the source of many concerns for the mining industry. Because the regulations were initially written at the federal level but are being administered at the state level, considerable confusion exists within the industry as to what is actually required. Based on the preparation and submission of over 30 monitoring plans for existing deep mines in Pennsylvania, West Virginia, and Ohio, we now have a very good feel for the detail the monitoring plans, as well as the costs to im plement the plans. We do not, however, feel confident in our evaluations of the long-term impact the ground water monitoring regulations may have on the industry.

Jan 1, 1980

By Francis X. Murray

Synthetic fuels will be the first major development effort to feel the effects of a new set of opposition forces. These confrontations will not be of the same variety as those which occured in the 1970s. Instead the synfuels industry, particularly in the West, will find itself confronting a new coalition of local political, community, and state spokesmen. They will oppose synfuels because the projects will represent a threat to existing lifestyles, political structures, taxes, social life, water rights, economics, and other politically sensitive considerations. In short, they mean change -- usually dynamic, full of unknowns and always threatening. The battles themselves may be fought technically over environmental issues, law and regulations; often these will be the instruments of the opposition. The real underlying problems will likely lie much deeper. In many cases environmental groups will be enlisted as the standard bearers; however, this approach may simply reflect the fact that environmental objections are convenient or at times the only tools at hand.

Jan 1, 1981

By Dominique Francois-Bongarcon

The rational and optimal determination of the design of a mining exploitation is a very intricate and difficult problem : the parameters are numerous, some technical, some economic or technico-economic which cannot be fully controlled; beside, deposits are estimated from very limited information and the choice criteria are not always quantitative, the economic context has to be anticipated by several years, and even the technological limits can change tomorrow. So, although very clever and performing numerical algorithms have been developed in recent years for open-pit design, we consider that this problem has not really been solved satisfactorily until now. The reasons are that people have concentrated their efforts on informatical algorithmical problems, and have assumed that the technical and economical data are well defined at the time of the study, which is generally not true. In particular, the mere fact of assigning dollar- values to blocks in order to maximize the total cash-flow is generally unrealistic because of the uncertainty of the data used. Consequently, the significance of the unique pit obtained as a result of these algorithms is questionable.

Jan 1, 1981

By C. D. Keith

Erie Mining Company, a pioneer in the iron ore pelletizing industry, has continued to develop methods and equipment to improve cost and quality. Under the management of Pickands Mather & Co., this property, owned by Bethlehem Steel Corporation, Youngstown Sheet and Tube Company, Steel Company of Canada, Ltd., and Interlake, Inc., has initiated a number of operating improvements for the taconite industry. One of the most noteworthy of these, which is applicable to the entire mineral industry, is the principle of fine screening with rappers (FSR). Erie's original efforts in the field of fine screening, which date back to 1961, were described in the April 1967 issue of the MINING ENGINEERING magazine. In that same month, Erie placed into operation a full scale PSR and regrind plant addition, capable of processing 10.3 million long tons of iron ore concentrates, produced by conventional taconite grinding, classification, and magnetic separation methods. Since this first successful commercial operation of the PSR principle et Erie, it has been applied in eight other iron ore beneficiation plants end is being tested by other U.S. and foreign companies. In addition to the use of PSR units at Erie Mining Company, Pickands Mather has applied PSR to other of its managed properties end to projects under development. This paper covers these applications as well as a now application at Erie Mining Company.

Jan 1, 1971

By Michael Rehbock-Sander, Romed Insam

"INTRODUCTIONThe idea of building a summit tunnel under the Brenner occurred to the Italian engineer Giovanni Qualizza as far back as 1847. But it was to be another 160 years to pass before a base tunnel was to be built.In 1971 the idea of a tunnel at the Brenner was dusted off again. The UIC, the International Union of Railways, commissioned a study for a new Brenner railway with a base tunnel. By 1989 three feasibility studies had been drawn up which formed the basis for further planning of the Brenner Base Tunnel.This was the start of the planning activities. In 1994, the European Union included the Berlin-Naples corridor in the list of priority projects. Ten years later, Austria and Italy signed a State Treaty to build the Brenner Base Tunnel. In that same year, what is today the BBT SE was established.PROJECT DESCRIPTIONThe Brenner Base Tunnel (BBT) with a length of 55 km is the centrepiece of the Helsinki-Valletta Transeuropean Traffic Corridor from Finland to Southern Italy. The BBT tunnel system connects in the north with the Innsbruck station (Austria) as well as to the feeder routes in the Lower Inn Valley, and opens to the south with the projected new line in the direction of Verona (Italy). The tangible design efforts have been underway since 1999; the start of construction of the first section was in the year 2007. The project is financed by the Italian and Austrian governments (each 30 %), as well as by the European Union (40 %).From 2027 onwards the Brenner base tunnel, including the existing lines connected with it, will carry a daily average of 330 trains (approx. 80% cargo trains and 20% passenger trains)."

Jan 1, 2016

By P. Grotjohann

In processing heavy mineral sands, the low feed concentration and respective high value of the desired minerals require high capacity production and sharp classification/separation techniques to reduce the specific production costs. The allflux® separator, a new process system introduced to the heavy mineral industry, meets these criteria in an economical way. Its two-stage process, a combination of rising current and fluidized bed technology, allows the treatment of extremely high massflows in a single unit. Using concepts that have proven successful in processing concrete sands for many years, testwork in coal, iron ore, and heavy minerals looks very promising.

Jan 1, 1998

By Paul H. Miller

After passage by the Congress, Public Law 95-87, the "Surface Mining Control and Reclamation Act of 1977" was signed by President Carter on August 3, 1977. This law, in its simplest form, was intended to control the environmental effects of surface coal mining and to ensure that mined land is restored to a condition equivalent to that prior to mining. Immediately after the signing, the wheels of government bureaucracy began turning to establish a new federal agency -the Office of Surface Mining Reclamation and Enforcement or OSM -in the Interior Department that would implement the provisions of the Act. Since this took time and because the Congress had not yet provided funding for OSM, a special task force was assembled within the Interior Department to begin the task of writing interim regulations to implement the Act. With respect to the use of explosives, the Act specified that a blasting plan be included in the application for a mining permit. The blasting plan will outline the procedures an operator will use to meet specified environmental protection performance standards. The performance standards established by the Act require explosives to be used only in accordance with existing state and federal laws and regulations and with regulations to be promulgated by the regulatory authority. The regulatory authority was defined as either a state agency operating under an approved state program or the OSM operating under a federal program. As a minimum, it was specified that the regulations should include provisions to require that: 1) a blasting schedule be published in a local newspaper and be mailed to local governments and to all residents living within 1/2 mile of the blasting site . 2) daily notice be given to residents in the area prior to blasting. 3) blast reports be prepared that are maintained for three years and available on request to the public. 4) blasts be designed to prevent injury to persons, damage to property outside the permit area, adverse impacts on underground mines and adverse effects on ground or surface water channels or availability outside the permit area. 5) upon request of residents or property owners within 1/2 mile of the permit area, preblast surveys shall

Jan 1, 1978

By M. Boucraut

After stating the advantages of the magnetic roasting technique as applied to iron ores, the authors report on technological research by I R S I D * in the field of magnetic roasting in fluid-bed furnaces This investigation was conducted first on an experimental two stage fluid-bed furnace which processed permanently 100-200 kg/h of ore, then on a three stage fluid-bed furnace with 1-2 t/h working capacity and at last on a 250 t/day pilot furnace The specific features of the IRSID process comprise - on the one hand, using special burners in the roasting reactor thereby ensuring a high production rate of the furnace - on the other hand, using a heat-exchanger where the preheating and cooling stages of fluidized ore are associated, so as to allow an efficient and simple cooling of both roasted ore and waste gases flowing out of the roasting reactor, thereby supplying heat to the crude ore and combustion air for the reactor burners Starting in 1965 the operation of the 250 t/day pilot plant at the Bazailles mine gave IRSID the opportunity of improving the conveying appliances and adapting them to the process, while perfectly confirming the metallurgical results obtained under ideal laboratory conditions

Jan 1, 1968

By James J. Scott

In the fall of 1976 the author started test work with Friction Rock Stabilizers in uranium mines of the West, principally in the Ambrosia Lake and Churchrock districts of New Mexico. Tests were also conducted in other uranium mines in the Rocky Mountains area. These mines are plagues with problems in ground control due to the weak formations in which mineralization occurs, mudstones, siltstones, weak sand, etc. For this reason, it is extremely difficult to obtain good anchorage for long periods of time with conventional mechanical roof bolts. Resin bolts give good anchorage but are expensive and, because of hole erosion and difficulties in installation due to inadequate equipment for mixing the resin and placing the rebar, they are not widely used. Field testing was also carried out in trona, limestones and hard and soft shale formations. The mechanism of the Friction Rock Stabi1izer support is discussed and pull test data presented for various rock types.

Jan 1, 1977

By D. N. Madge

A description will be given of an approach to plant process automation based on the strategy of first developing an information system followed by later development of process models. The advantages of this approach over the unit process control will be outlined. Some insight will be given into the risks associated with this method. These risks can be shown to be primarily economic.' Some reference will be made to two Cominco installations in the interests of illustrating the generality of the information systems approach.

Jan 1, 1972