Search Documents

By Y. Lizotte

The purpose of this paper is to describe a stochastic simulation program used to assess several dispatching rules applicable to small scale computerized systems for optimizing truck/shovel productivity. The system studied is semi-automated with a dispatcher communicating instructions by two-way radio. The simulation program is structured on an advance clock approach which enables the insertion of dispatching rules at various points in the haulage net- work. The rules tested include minimize shovel idle time, maximizing immediate truck use and assigning trucks to shovels to meet specific production objectives. A variation of the traditional "Match Factor" is implemented to maintain fleet balance throughout the shift. A mine case study demonstrates how the dispatching rules increase productivity of such semi-automated dispatching systems. Practical problems involved in the implementation of small computerized dispatching systems are also discussed.

Jan 1, 1986

By S. N. Chadha

INTRODUCTION The work described here refers to the Genesee River Interceptor Southeast Project. This project is a part of the Combined Sewer Overflow Abatement Program, Phase I, for the Rochester Pure Water District, Rochester, New York. Our contract required the design of a 13,200-feet long main tunnel, 14 feet finished diameter, approximately 100-120 Feet below ground; drop shafts and diversion tunnels to deliver surface flow to the main tunnel; a gate chamber whereby the main tunnel is dropped 35 feet, and provision made for connection to the future tunnel in Phase II, as well as a host of other surface structures. Cross sectional dimensions for the structures involved varied from 16 feet circular to a 20'x50' horseshoe, in a competent rock formation consisting of Lockport Dolomite and Rochester Shale. In the construction of a rock tunnel, the problems of the tunnel designers are as follows: 1. To evaluate stresses in the rock as a result of excavation. 2. Design a temporary support system to prevent any rock failure during the period of construction. Design of this temporary support system is empirical. Design loads given by empirical relations are dependent upon the rock quality and size of opening. Temporary support system may either be steel frames closely spaced along the length of tunnel and tied together, in the case of poor rock, or, an even spacing of rock bolts in the case of competent rock. 3. Design a final lining for the service loads. Service loads, in our case of a water-carrying tunnel, are hydrostatic pressure due to ground water, deadweight of lining) pressure of contained water and time dependent rock loading. The constitutive properties of the rock are extremely complex because of discontinuities, pre-existing stresses due to overburden, material symmetries and changes of initial state associated with the process of excavation. The changes of initial state may be changes of stress fields along with the consequent yield of the material or the extension of existing discontinuities.

Jan 1, 1977

By Reed S. C. Rogers

The breakage parameters of phosphate ore were determined by batch first-order grinding studies in a laboratory ball mill according to the procedures described in the text by Austin, Klimpel and Luckie, using a slurry density of 70 weight percent. The results were scaled to five larger mills of 0.56 m diameter by 0.91 m length (2 ft. by 3 ft.), 0.82 m by 1.52 m (3 ft. by 5 ft.), 3.36 m by 7.90 m (11.5 ft. by 25 ft.), 4.41 m by 9.10 m (14.5 ft. by 30 ft.), and 5 m by 11.1 m (17 ft. by 36 ft.), assuming equilibrium ball charges for the full-scale mills. The results were used to predict product size distribustions and capacities for batch grinding in the 0.56 m and 0.82 m diameter mills and open circuit grinding in the 0.82 m diameter and larger mills using a one-large/two-small reactors in series model fitted to the residence time distribution measured in the 4.41 m diameter mill. The simulated results were compared to plant data for ranges of mill capacities. It was found that the simulated product size distributions were in good agreement with the experimental values below the 70% passing sizes, but did not agree so well in the top sizes. The predicted capacities were in approximate agreement with experimental values for the pilot-scale mills, were about 7 percent too high for the 3.36 m and 4.41 m diameter mills and about 25 percent high for the 5 m diameter mill. Use of the Bond method with the measured Work Index of the phosphate ore gave capacity predictions that were 45 to 150 percent too high.

Jan 1, 1985

By S. S. Sephton

Sintering as applied to agglomeration of ferrous fines has shown little growth in the United States in recent years. The general concensus was that most of the existing facilities would remain in production at a reduced tonnage to dispose of and recover solid waste from steel plants. Further growth for ferrous sintering technology was not in sight in the United States and in the early sixties expansion came to a virtual standstill, however, we witnessed a rapid emergence of a tremendous pelletizing industry. On other continents, due to different raw materials supply and capital structure, sintering technology continued to grow, with a more cautious development of pelletizing installations. In the U.S. the diminishing supply of good quality, high grade coarse ore resulted in eventual disappearance of high grade ore fines for sintering. The finely divided concentrates produced from lower grade ores were not amenable to this type of agglomeration, but were more suitable for pelletizing. Furthermore, pellets seemed to possess all the features of an ideal blast furnace feed; namely pellets are free flowing, uniform in size, strong, with extremely uniform chemical composition and good reducibility. Importance and demand for such well stabilized furnace feed further increased as size of newly installed blast furnaces continued to grow. The in- creasing demand for a uniform, stabilized burden coincided with the effort to produce a fully beneficiated burden for smelting, thus reverting the blast furnace to its primary function of smelting.

Jan 1, 1973

By Stephen P. Signer

The U.S. Bureau of Mines is developing an intelligent system for roof' control that uses both an expert system and neural networks to improve the capability of mining engineers to evaluate roof support effectiveness for ground control in coal mines. The expert system com- pares roof support capacities with the support requirements estimated to be necessary to maintain entry stability. It does this by evaluating the results of tests on various types of roof support and establishing the maximum allowable load according to anchorage capacity and yield strength of the support. After the user enters geological information (rock properties, geometry of the opening, in situ stresses, bolt pattern parameters, etc. ), the expert system compares the predicted required loading to the roof support capacity and gives the operator advice on the adequacy of the design and how improvements could be made. A good source of the real-time data necessary to allow the expert system to make decisions will come from a roof bolting machine being developed by the Bureau of Mines. Researchers have collected data from a Western coal mine on drill bit position, penetration rate thrust, torque, and rotation rate. Using this information, two neural net- works were developed to identify different types of strata and features in a mine roof such as rock type, rock compressive strength and joint characteristics. The result is a system that can assist a mining engineer with design information that can be constantly updated as mining progresses.

Jan 1, 1992

By Barrie A. Wigmore

There are two aspects of financing western coal development -- whether there is going to be enough money to finance the prospective large development of the industry, and the specific techniques of raising money for that development. To take the first question of whether there is going to be enough money around to finance your industry, I think it is quite clear that the restrictions on the development of western coal are going to be non- financial. Environmental impact problems are creating the greatest delay in coal mine development, at the moment; but getting enough personnel, mining equipment, railroad equipment, and failure of the Department of Interior to act on leasing federal coal lands all appear likely to create significant bottle- necks in the development of western coal -- larger bottlenecks than financing. Financing appears straightforward for the industry. There are many projections of the financing required to meet Project Independence goals. The National Academy of Engineers estimated that development of 500 million tons per annum of western coal would be necessary by 1985 to meet the Project Independence goals which might require $20 billion of capital spending. It is generally agreed that 500 million tons a year is not a realistic possibility. Carl Bagge?s estimate of production of 250 million tons a year by 1983 appears a more reasonable projection. Development

Jan 1, 1976

By Fabian Laumen, Sunny Schoone, Felix Leaman, ELISABETH CLAUSEN

The acoustic emission (AE) technology has a high potential for flow characterization in hydraulic transport processes. For instance, in deep-sea mining, there are applications where manganese nodules are transported from the bottom of the sea to the surface or a transport ship. Here, an AE-based flow characterization system plays an important role to avoid the transport of non-related objects. However, the structural materials for the components of this system must be carefully selected to ensure resistance against corrosion and a good AE signal transmission. Therefore, in this experimental study, we evaluated the AE attenuation behavior of four different materials that can be employed in marine environments due to their properties. The results were obtained using thin plates and they indicate which materials have the highest and lowest attenuations. Moreover, we provide insights regarding the different wave modes that propagate on the plates.

Mar 2, 2023

By Thomas M. Tharp, Mark A. Travers

A new method is presented for precracking three-point bending specimens for fracture toughness testing. A notched specimen of rectangular cross section is placed on a flat loading platen, with paper between specimen and platen. The specimen is loaded from above through a roller placed directly over the crack. The thin, high compliance joint between specimen and platen causes a distributed load on the bottom of the specimen. This results in bending at the cracked section and crack initiation at the notch tip. Since the joint is thin, its stiffness increases rapidly with deflection and crack propagation in the specimen generally remains stable and controllable. Fracture toughness KIC in a sandstone directly overlying the No. V coal was measured to be 0.27 MPa m 1/2. Even for cracks 1 cm long this value of KIC results in substantially lower effective tensile strength (modulus of rupture) in roof beams than is expected from intact rock strength.

Jan 1, 1986

By B. T. Lusk, J. J. Silva Castro

Currently, there are several methodologies to assess ground vibrations from blasting. Of all available methodologies, one that is becoming more important is the waveform superposition or signature hole technique. This technique is based on a signature waveform assigned to each hole to build the complete waveform for the whole production blast, using the convolution between the time initiation sequence and the signature hole waveform. In the basic methodology of the signature hole technique, the waveform hole-to-hole is assumed to be the same. Several studies and field tests have proven that the waveform hole-to-hole, even in ideal rock mass conditions (rock mass with little or no joint system), changes. In addition to distance or confinement, other factors that could change the waveform hole-to-hole include different geologic paths from the source to the monitoring point and a different energy output of each hole, due to hole loading, explosive composition and/or contamination, priming, etc. These factors result in varying waveforms generated for each hole, making the waveform produced by each hole a somewhat random process. There is available in the literature some proposals to include variability in the waveform hole-to-hole, but the parameters involved are complex and difficult to estimate. In this paper, the variability in the signature waveform hole-to-hole in a blast event was recorded through a field test, and a proposal to include signature waveform variability to develop an equation based on the Fourier series is presented. This methodology is the basis for a future signature hole analysis using a Monte Carlo scheme, taking into account the variation of the amplitude and the frequency content of the waveform hole-to-hole in a production blast event.

Jan 1, 2012

By C. R. McClung

"Molybdenum, in the form of molybdenite, is a common byproduct of many copper mining and concentrating operations. While the recovery of most copper sulfide minerals is principally liberation controlled, the recovery of molybdenite is much more complex, with fully liberated particles commonly lost to tailings.A geometallurgical investigation was undertaken of molybdenite from the Bingham Canyon deposit with the aim of determining what effects, if any, mineralogy and the mineralogical attributes of morphology, angularity, liberation and size have on molybdenite recovery in the processing circuit. A set of samples was collected from the ores and products of Rio Tinto Kennecott’s Copperton Concentrator. The samples were analyzed by normal polarized reflected light microscopy, X-ray diffractometry, and scanning electron microscopy using a Mineral Liberation Analyzer, revealing the presence of two distinct types of molybdenite, which are the two polytypes: hexagonal (2H) and rhombohedral (3R). The 2H polytype occurs as textbook-shaped particles in quartz-molybdenite veins located in the core of the deposit, while the 3R polytype occurs as disseminated, ball-shaped particles with a dull or frosted appearance along the margins of the mineralized intrusive body or central core. Each polytype exhibited metallurgical properties consistent with those reported in the literature. The 2H polytype is easily ground, kinetically “faster” floating and displays surface attributes that are amenable to higher rates of recovery. This commonly results in the production of a high-quality molybdenum concentrate under normal operating conditions at most copper concentration operations. The 3R polytype is difficult to grind, kinetically “slower” floating and displays surface attributes that are less amenable to recovery. Therefore, in deposits with higher concentrations of the 3R polytype, modifications to operating parameters may be necessary to improve the recovery of molybdenite.A preliminary investigation into the metal budget of porphyry copper and molybdenum deposits indicated a possible positive correlation between total economic metal budget and polytype content. Higher concentrations of the 3R polytype appear to be more prevalent in gold-enriched porphyries than in molybdenum-enriched porphyries. This may help explain why it is easier to obtain higher rates of recovery in molybdenum ± tungsten-rich deposits, which contain little to none of the 3R polytype. There is a potential for the metal budget of a porphyry deposit to be used as an indication of the molybdenite polytype present as well as its impact on the economics, in terms of exploration, and the processing circuit, in terms of plant design."

Jan 1, 2016

By Matthias Neuenschwander, Andreas Theiler, Patrick Steinle, John Singer, Martin Vogel, Diego Martini, Ömer Ündül, Markus Weh

"Quartz Dust is a major health hazard in underground works, wherever the ground contains quartz and depending on the chosen method of excavation. A research project initiated by the Swiss Tunnelling Society and realized by the Swiss Federal Institut of Technology, Zurich, established a correlation between the potential of quartz dust generation during excavation and well known geotechnical characteristics – the Cerchar Abrasivity Index CAI and the Uniaxial Compressive Strength UCS - of ten typical Swiss rocks. The results are at the center of a new guideline by the Swiss Society of Engineers and Architects on the requirements for early project stages regarding ventilation and logistics in function of the quartz dust related risk of the expected ground type of the project. The approach presented could be applied worldwide, contributing to more effective health protection as well as to better cost stability in underground works. CONTEXT Respirable quartz dust (aerodynamic diameter of particles < 10 micron) is universally recognized as a major workplace health hazard. Chronic bronchitis, silicosis and lung cancer can be caused by excessive exposure to quartz dust, as has been proved by many medical studies. Therefore, the legislations of many nations specify a maximum workplace concentration (Maximale Arbeitsplatzkonzentration MAK, Occupational Exposure Level OEL). In Switzerland, for example, the Threshold Limit Value TLV for respirable Quartz or Crystalline Silica imposed by the Federal Committee on Exposure Levels (Grenzwertkommission) is 0.15mg/m3 air. Some nations refrain from establishing a OEL because of the carcinogenic nature of quartz."

Jan 1, 2016

By Donald P. Tuchman, Emanuele G. Cauda, Steven E. Mischler, Elaine N. Rubinstein, Jay F. Colinet

The PDM3600 and PDM3700 are two closely related person-wearable dust monitors manufactured by Thermo Fisher Scientific. Both are based on tapered element oscillating microbalance technology and provide nearly real-time, mass-based readings of respirable dust concentrations. From a monitoring perspective, the primary difference between the models is the PDM3600 has an integrated cap lamp with attached inlet, while the PDM3700 has no cap lamp and a revised inlet attaches to the worker’s lapel. Using coals of varied origin and employing a wide range of concentrations, side-by-side measurements from these instruments were collected under controlled laboratory conditions and then compared. By use of ordinary least squares and weighted least squares regression methods, followed by mixed model analysis, results suggest there is no statistically significant or practical difference in instrument performance. The two monitors are equivalent for the field dust concentration measurements for which they were designed.

Feb 28, 2024

By R. M. Reyes, D. Negrete, G. Herrera

First Majestic Silver Corp’s La Encantada Silver Mine is a producing mine with a capacity of 3,000 tonnes per day. The La Encantada team is currently constructing two small-scale caving mines, including the San Javier breccia caving mine. The new mine is constructed within a mineralized breccia body composed of clasts of varying sizes and with very poor rock quality. Due to this poor rock quality, primary and secondary supports are required to support both the development and production stages. Since the proximity of the new mining levels to existing old workings, correct selection of the support system and proper production controls, instrumentation, and monitoring are very critical to maintain the stability of the pillars and fortification elements. An increased ground deformation due to the load transfer during the production stage is expected. This report reviews the primary and secondary support elements used in the different stages of mining, the monitoring of ground deformation, and the steps taken to analyze and visualize the collected data in order to enable the geotechnical team to manage caving stress and maintain pillar stability. INTRODUCTION First Majestic Silver Corp. (“First Majestic”) is a Canadian mining company focused on silver production in Mexico that operates six producing silver mines, including La Encantada Silver Mine (“La Encantada”). First Majestic acquired La Encantada in 2006. La Encantada is located in the northwestern portion of the state of Coahuila, in northern Mexico, in the municipality of Villa de Ocampo. The mine lies in the northern part of the Sierra Madre Oriental physiographic province. The mine location is shown in Figure 1. La Encantada is a producing mine, with a mill processing capacity of 3,000 tpd, and a 4,000 tpd capacity cyanidation leaching circuit equipped to process fresh underground ore and old tailings amenable to be reprocessed. The mine is currently employing several mining methods, including overhand cut and fill for narrow veins, small mantos, and other minor deposits. A subset of caving methods are applied on the larger, but weak, mineral deposits, such as at the San Javier breccia and La Prieta breccia. La Encantada consists of vein, manto, breccia pipe, and chimney deposits with concentrations of silver, lead, iron, and zinc in oxidized mineralization enclosed by calcareous sedimentary formations of Cretaceous age. At deeper levels, there is sulphide mineralization in skarn with zinc and silver concentrations associated with a granodiorite intrusion.

Jan 1, 2019

By D. A. Baker, E. A. Gyawu, K. Awuah-Offei

Several underground coal mining disasters, such as Upper Big Branch in 2010, have revealed technological and organizational shortcomings related to self-escape. Efforts to address these gaps have primarily been top-down, that is, identified and implemented by upper management or external governing bodies. In contrast, this study employs a novel miner-centered approach to identify perceived technological boundaries to self-escape. Using a semi-structured, scenario-based survey, we elicit direct feedback from miners about current, emerging, and hypothetical technologies aimed at improving self-escape during mine emergencies. The results show a general high usefulness rating across all 21 technologies in the survey. Miners who work underground (both outby and working face miners) appear to give higher usefulness ratings overall than miners on the surface and other locations. This work will be directly applied to a series of proof of concept and prototype studies on self-contained self-rescuers (SCSRs), refuge alternatives (RA), and communication devises aimed at improving self-escape technologies through miner-centered research and design.

Mar 2, 2022

By M. Li, W. R. Reed, J. P. Rider, J. D. Potts

"The National Institute for Occupational Safety and Health (NIOSH) recently developed a series of validated models utilizing computational fluid dynamics (CFD) to study the effects of air-blocking shelves on airflows and respirable dust distribution associated with mediumsized surface blasthole drill shrouds as part of a dry dust collector system. Using validated CFD models, three different air-blocking shelves were included in the present study: a 15.2-cm (6-in.)-wide shelf; a 7.6-cm (3-in.)-wide shelf; and a 7.6-cm (3-in.)-wide shelf at four different shelf heights. In addition, the dust-collector-to-bailing airflow ratios of 1.75:1, 1.5:1, 1.25:1 and 1:1 were evaluated for the 15.2-cm (6-in.)-wide air-blocking shelf. This paper describes the methodology used to develop the CFD models. The effects of air-blocking shelves and dust collector-to-bailing airflow ratios were identified by the study, and problem regions were revealed under certain conditions. IntroductionSurface blasthole drilling can generate considerable amounts of respirable silica dust. These high dust concentrations can be exacerbated by the high silica content as drilling cuts through silica-bearing materials such as sandstone and shale, causing overexposures for miners to respirable silica dust. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is often fatal. A review of the Mine Safety and Health Administration (MSHA) respirable silica dust sample database from 2010 to 2016 for metal/nonmetal mining shows the following overexposure rates for occupations related to blasthole drilling: • 14.1 percent of rotary air drillers were overexposed to respirable silica dust (22 out of 156 samples).• 5.8 percent of rotary drillers were overexposed to respirable silica dust (nine out of 155 samples).• 7.3 percent of drill helpers were overexposed to respirable silica dust (three out of 41 samples).• 7.5 percent of blasters/shotfirers were overexposed to respirable silica dust (three out of 40 samples)."

Jan 5, 2018

By Robert J. Auber, Thomas R. Scotese

The West Leg Interceptor is part of a new sanitary sewer system in the southwest suburbs of Cleveland. The first two construction contracts were excavated in glacial soils varying from hard tills to pressurized silts and flowing sands. These soil and groundwater conditions were locally problematic during shaft and tunnel excavations and final lining construction. A variety of solutions were developed primarily during construction. During the WLI-1R Contract, subgrade pressures, continued ground losses, and displacements necessitated extra eductor wells and modified inverts for stabilization of shafts. At the WLI-2Contract, one shaft excavation in similar ground required only one extra well. In the WLI-1R tunnel, localized inflows of groundwater, silt, and sand through the geotextile fabric were stopped by cement grouting. In one WLI-2 connector tunnel, damage to the TBM flood doors combined with wet, flowing silt and sand led to ground losses, surface settlements, plugging, patching, and chemical grouting. The concrete lining in the main WLI-2 tunnel required remedial work to improve watertightness at joints.

Jan 1, 1999

By K. Rushdi, B. E. Abulnaga

The conventional Froude number is blind to the presence of solids, their density and their concentration in a stream of slurry mixture such as tailings flowing in an open channel. This often leads to rough approximations of subcritical, critical and supercritical regimes, based on one phase flow Froude number, limiting subcritical to a value smaller than 0.8 and supercritical to values above 1.4, as proposed in the past by Green, Abulnaga and other authors. While acceptable for small flows, such approximations can be uneconomical for the larger flows encountered in some modern plants that treat up to half a million t/day. A review of concepts of a densimetric Froude number sheds some light on the effect of solids on stratification prior and subsequent to a hydraulic jump. While the approach is heavily borrowed from modern sedimentology, it provides a useful tool to designers of large launders or open channel tailings systems. These concepts are reviewed with some practical examples.

Jan 1, 2013

By Martin Knights

The UK Industry is preparing a new guide on Tunnel Asset Management that reflects current industry advances, in developed technological innovation and evolving tunnel asset owner requirements. This will enable asset owners to have a trusted practical guide that can support technical and commercial decisionmaking regarding tunnel assets and aging infrastructure. It will also provide updated guidance for a spectrum of stakeholders including: • Consultants. • Contractors. • Planners, insurers. • Academia. • Government. Industry views will be crucial in the preparation of the Guide that will assist proactive & predictive planning and maintenance regimes and the availability of the asset. The Guide will enable changes in current working practices, share updated recommendations and provide a route map to implement future requirements for tunnel asset management. The generic content of the Guide would be applicable to North American practice.

Dec 1, 2022

By Mokhinabonu Mardonova, Yosoon Choi

Open-source technology to support Industry 4.0 has become the target of academic research in many sectors. This study reviews the trends of open-source technology, its forms, and some industrial applications. As a case study of the use of open-source hardware and software in the mining industry, this study proposed a low-cost environmental monitoring system for nonmetallic underground mines to support mine safety and occupational health. The system was developed using open-source hardware, Arduino and 3D printer, to design the monitoring device, and open-source software, MIT App Inventor, to develop an Android application for smartphones to enable remote communication with the system. Field experiments were conducted at an underground tunnel and a nonmetallic underground mining site to assess the performance of the system in mobile and static modes, respectively. Although a few limitations related to the precision of the low-cost dust and gas sensors exist, the findings of the experiments show that the mining industry can benefit from open-source technology deployment when considering cost factors.

By Eberhard Stolarski, Michael Tacke

When the oxidized surface gold deposits are mined out, the underlying refractory gold ores become the challenge of treat­ment systems. The size and value ofrefractory gold ore reserves are a function of recovery efficiency and operating cost. The start-up of LURGI's gold roasters at NEWMONT's Carlin site has established whole ore gold roasters as a key to high gold recoveries. The ores from several deposits of the Carlin trend are roast­ed utilizing LURGI / NEWMONT technology, which has achieved gold recoveries approaching 95%. This is in dramatic contrast to the traditional perception that roasting is limited to gold recoveries in the mid 80's. Extensive investigation in pilot scale is required to achieve stable high gold recoveries for most variables in the ore body. The key question for all pilot tests is the classic question of (ROM) run of mine ore roasting or concentrate roasting. All variables are dominated by the leaching/ recovery char­acteristics of the natural ores. The degree ofrecovery improve­ment by roasting / calcining establishes the frame of the eco­nomical conditions. The full range of flexibility is required for the design of the plant to allow for ore variations in heat values, combustible con­tents, agglomeration behavior and off-gas composition. The variables in the ore body influence, therefore, the price of the plant proportionally to its flexibility. Concentrates are usually fairly stable in composition, com­bustion behavior, heat values and particle size since they are a product of the very selective flotation process. Flotation is not the successful process step when the tailings remain high in refractory gold contents.

Jan 1, 1996