Search Documents

By William A. Prosser, Kyle R. Ott, Philip Rice

"INTRODUCTION The existing Baltimore and Potomac (B&P) Tunnel accommodates Amtrak (National Railroad Passenger Corporation) and MARC (Maryland Rail Corporation) service between Baltimore, MD and Washington, DC and occasional local freight service. The Baltimore and Potomac Tunnel Replacement Project proposes new tunnel construction through Baltimore, Maryland along the Northeast Corridor (NEC) that maintains connections to Baltimore Pennsylvania Station. After the Replacement Project is constructed and operational, the disposition of the existing tunnel must be determined. The tunnel could be abandoned; however, considering its location in a congested downtown, alternative uses have been considered to take advantage of this unique piece of infrastructure by repurposing it. Alternative uses for the existing 140-year-old B&P Tunnel may end up being cost effective and should be considered, as the tunnel can be made accessible to construction crews for extended periods of time that will allow for efficient work activities unlike when it is fully operational. Possible alternatives include conversion for non-rail use, rehabilitation, or complete modernization for continued rail traffic. The following paper describes the four potential fates of the conceptual designs for the existing B&P Tunnel. The four concepts include: • No Build – rehabilitate to keep the tunnel operational. • Abandonment – complete or partial sealing of the tunnel. • Adaptive Re-Use –repurpose the tunnel with sustainable building practice. • Full Rehabilitation and Modernization – bring to current fire-life safety aspects. Of the four concepts, only the no build addresses maintaining the tunnel while it is under traffic. The remaining fates address the existing tunnel after the new tunnel is operational and railroad traffic has been diverted to it. Development of these conceptual designs were provided in a concept design study (Parsons Brinckerhoff/Parsons, 2015) that supports the National Environmental Policy Act (NEPA) review process for the Project, which includes evaluation of possible alternative uses of the existing B&P Tunnel."

Jan 1, 2016

By Jerry Wang, Greg Bold, Mahmood Khwaja, Rebecca Caldon, William Simcoe

Phase III and Phase IV of the Beaver Creek Clean River Project, Albany, NY, includes microtunnel construction of 2,320 feet of 48-inch/36-inch internal diameter (ID) conveyance pipe and a 525 foot long 9.5-ft horseshoe shape roadheader excavated tunnel. Notable challenges were encountered during the construction including mixed face tunnel conditions, undocumented existing fill ground conditions that resulted in settlement during shaft construction, and unstable tunnel face conditions. This paper discusses several of the key challenges encountered during construction and selected solutions to construction sequencing and methodology to successfully complete Phase III and Phase IV of the Beaver Creek Clean River Project.

Dec 1, 2022

The need for an integrated approach to optimization of unit operations in both the pit and the mill has long been recognized, but the complexity and nature of the overall problem has up to now resisted solution. This paper reports on a modeling methodology which couples symbolic and numeric computing to unify operations in both the pit and mill. The ultimate goal of this work is to optimize all operations that are influenced by blasting. Blasting plays a key role in all facets of operations. Obviously, drilling and blasting costs are determined by blast design, but the down-stream costs that are closely related to blasting results are often treated as separate functions: loading, hauling, cleanup, and crushing and grinding are all heavily influenced. Diggablilty and bucket fill factor are a function of fragmentation, the condition of the floor and uniformity in the shape of the muck pile. Likewise, cycle times and loading delays partially determine haul cycles, while fragmentation distribution and size determines the efficiency of truck loading. Removal and breakage of oversize causes loading delays and increases cleanup costs. The influence of blasting doesn't stop at the crusher. Mill productivity, power consumption, and maintenance are a function of the feed. Even at the SAG mill a reduction of a critical particle size during blasting can increase throughput. Thus, a bottle-neck for production far removed from unit operations in the pit can be alleviated by a modification in blast design. The question is: how do we optimize blasting with respect not only to itself but to al\ related mining and milling operations? For that matter, how do we even model blasting so that we can control the results of a blast?

Jan 1, 1991

By Wayne F. Crockett, Martin H. Col

Gold, as a precious metal, has been sought for several thousand years. During this time economics have generally determined whether or not a deposit is minable. Today, few would spend $500.00 or $1,000.00 to produce one ounce of gold, yet most gold deposits currently being mined would have such costs if they were mined using the methods of the 18th century. Innovation has been the key to success in the world of mining. We are constantly having to look for new ways to mine deposits of lower grade, at greater depths, or with higher stripping ratios. The mining of placer gold deposits has always been subject to the volatile swings of the world price and the constant rise in production costs. The rise in costs is compounded by the drop in overall ore grades. Occasionally, a major technological innovation will dramatically reduce the costs of placer mining to allow previously marginal or unminable deposits to be mined at a profit. The continuous bucketline dredge was the last such major innovation in the gold placer mining. The continuous bucketline dredge has allowed large volumes of placer deposits to be picked up and processed on a continuous basis. Unfortunately, as the overall grade of the deposit declines, it becomes impossible to process enough ore to pay for the operating costs. There are many gold deposits around the world waiting for the next technological innovation that will allow them to be mined. One such deposit has been the Grey River deposit near Greymouth in New Zealand. The deposit contains gold reserves of 8992 kg, yet the deposit has been sitting idle for many years because the average value

Jan 1, 1988

By C. C. Bailie

This paper will be concerned with those mineable coal measures at depths necessitating deep mine operations in the range of 200 feet to 800 feet in depth. The area is generally classified as the Southern Illinois Field but more specifically includes that part of the state south of a line extending from St. Louis, Missouri on the west to Vincennes, Indiana, on the east. This embraces an area which presently includes a total of 38 shipping mines and 5 local or truck mines. Of these shipping mines, 22 are deep (shaft or slope) mines and the remaining 16 are strips. The average annual production of the shipping mines is around 29 million tons. The presently classified mineable reserves of the area are estimated at around 70 billion tons.

Jan 1, 1964

By Dan Nilsson

Open pit mining is the strong sector of the American mining industry. In the middle of the 60's. 17-18% of the ore in metal mines was mined with underground methods. From the middle of the 60's to 1980 the production in open pit metallic mines increased from about 400 to close to 600 million short tons while at the same time the underground mine production decreased a little, from about 90 to about 80 million tons. Less than 15% of the ore prodction now come from underground mines. Large amounts of waste rock were also handled in the open pits. In the middle of the 60's about 600 milion tons were handled, in 1980 1,200 million tons were moved. This means that the average stripping ratio increased from about 1.5 to over 2.0 tons of waste rock per ton of ore, figure 1.

Jan 1, 1983

By Yi Luo

Longwall coal mines are frequently located in steep mountainous areas with narrow valleys. In order to protect surrounding watersheds and residential structures, support areas are left under the valleys. However, the indirect subsidence effects to the residential structures due to the potential topography effects can be a serious problem. The present study examines a longwall mine in southern West Virginia located in an area with an average slope of about 30°, or 58%, and with an overburden depth that varies from 49 to 376 m (160 to 1,235 ft). A comprehensive investigation was carried out to assess the subsidence and topography effects, as well as other ground control issues at this site. Surface and subsurface movements and deformation were predicted and their direct effects on nearby streams and structures were assessed. The potential and indirect subsidence influences of surface topography effects were assessed. The techniques and results of this investigation are presented in this paper. It shows that the direct and indirect subsidence effects on the streams and residential structures should be insignificant. The post-mining observations agreed well with this study.

Jan 1, 2010

By A. K. Ghose

The increasing application of roadheading machines in the coal industry has prompted the development of an appropriate selection methodology for such machine applications in specific locales. Accurate geological sections and comprehensive rock testing are required for all machine tunneling. Using suitable geotechnical parameters and index tests, sensitive both to excavability and standability of the strata, a classification scheme has evolved to help evaluate the rock mass vis-a-vis application of a given weight-class of roadheading machine. The classification parameters include point load index, brittleness, abrasiveness, average crack density, and ground water, which with assigned numerical ratings, lead to a quantitative global rating of the rock mass. For each rock mass class, the selection of an appropriate roadheading machine is recommended. The paper illustrates the application of the rock mass rating system and also describes simple index tests for evaluating the classification parameters for brittleness and abrasiveness. Manuscript not received in time for publication.

Jan 1, 1983

By S. P. Liebenberg

During the past fifteen years significant progress has been made on carbon-in-pulp (CIP) technology for the extraction of gold. While most research on the mechanisms and kinetics of CIP sub-processes has focused on the adsorption step only, auxiliary unit operations such as elution have received less attention. The mathematical models which have been developed for elution at the University of Stellenbosch can be used for design as well as process optimisation by incorporation into an overall CIP simulation program. Except for these models, no other comprehensive models for the complex elution process are available. It is the aim of this paper to review recent modelling work on competitive elution from activated carbon.

Jan 1, 1995

By C. H. Bucknam

An interlaboratory testing program was undertaken in support of an ASTM standardization program for simultaneous combustion-infrared analysis for carbon and sulfur in ores and related materials. Statistical analysis results from the study are used to generate the within-laboratory and between-laboratory precision data needed for standardization of the methods. The interlaboratory precision statistics are also interpreted to estimate the uncertainty in calculation of net carbonate value classifications using a simplified quantitative risk analysis technique.

Jan 1, 1998

By Richard Hogg, Erol Kaya, Jan M. Mutmansky

Characterization of the size, shape, chemical composition, and mineralogical content of mine airborne dusts generally requires a larger mass of dust particles than is typically collected using traditional sampling devices. In this paper, the general design of a passive dust collector is described and the field results are presented. The collector was constructed of galvanized sheet metal duct with a resin-coated honeycomb to provide an elutriation-type system for particle collection. Several versions of the collector were used in the field portions of the research. The dust samples collected from underground coal mines were found to possess angular particle shapes, relatively consistent size distributions, and elemental compositions that showed relatively little variation, at least for the more prevalent elements. In addition, the distributions of particles sizes obtained from the passive dust collector appear to be similar to those of samples collected at the same time in a conventional personal sampler except that the passive device seems to collect a larger quantity of coarse, non- respirable particles. Conclusions on the suitability of this dust collector for collecting characterization samples are presented. In addition, the potential for using such a dust collection system for supplying dusts for biomedical research is discussed.

Jan 1, 1993

By T. A. Moss

The installation of equipment and structures at mines often requires the evaluation of unique loading and operating conditions. Consideration of these unusual features is required throughout design and construction and into operation. The necessity for employing sound civil, structural and mechanical engineering techniques to the design of structures and equipment is well understood. However, the influence of geotechnical factors on the overall behavior during construction and operation of these facilities is less appreciated. Mine operators routinely perform exploratory drilling for the purposes of defining ore deposits. These exploration activities can be extensive and often include provisions for assessment of subsurface conditions as they relate to the mining operation, i.e., requirements for ground support. All of these factors are important to the economics of the mine and are well justified. Surface facilities are provided to access and service the mine and they play an important role in the successful development and operation of a project. Headframes, hoist foundations and shaft collars, in particular, are examples of unique installations encountered at underground mine sites. The design and above surface behavior of these facilities can be analyzed with the usual fundamental engineering practices employed throughout the engineering professions. This requirement during the project development is understood and adopted. Unfortunately, near surface exploration for the purposes of assessing soil and rock conditions for foundations are often given a reduced priority and less consideration. This paper is aimed at providing an outline into the benefits and importance of performing such explorations and to provide a brief discussion of the merits of such an approach. References in the paper relate particularly to shaft headframes, hoists and shaft collars but the issues raised apply equally well to other installations of a similar nature, e.g. milling equipment.

Jan 1, 1992

By M. Schultz

The cost of remediation often drives the selection of the preferred remedial alternative at hazardous waste sites. The use of probabilistic cost/risk analyses can aid in predicting costs of remedial alternatives. Three types of information are discussed in performing cost/risk analyses: (1) data on the quantity of contamination versus the contaminant concentration; (2) unit costs of remediation for the remedial alternatives; and (3) risk to contaminant concentration relationships. Cost/risk evaluations are performed on a site-by-site basis, to account for combined risks of different contaminants and differences in quantity to be remediated versus contaminant concentration. The cost/risk analysis produces a graph of risk versus cost for each of the remedial alternatives. These costs are then compared to facilitate selection of a preferred alternative. An example of comparison of alternatives is illustrated for a historic coal gasification site.

Jan 1, 1992

By Frederico J. Price

This paper describes the production of a specific iron oxide pellet that has given very good and consistent results as feedstock for HYL-Process Direct Reduction Plants. The sponge iron originated from these pellets has been used for the economic making of almost 15 million tons of low carbon steel via electric arc furnace meltshops. An overview of mining, benefication, pelletizing direct reduction and steelmaking for this case is given with emphasis on the characteristics of the self-fluxing oxide pellets. HYL Operator and management training is described.

Jan 1, 1979

By R. J. Sweigard, G. T. Lineberry, B. K. Slone, F. A. James III, D. S. Maggard

The depth at which it becomes more economical to use slope access instead of box-cut access for nearsurface coal reserves is termed the "transition depth." The transition depth can be established for a given coal property by considering cost estimates for those parameters that determine respective access methods. Fourteen parameters that influence access cost were identified, and ranges for these parameters were determined. A transitiondepth formula was developed to permit the determination of which is the better method of accessing a reserve, given information such as high wall slope, road width, total bench width, pit dimensions, road grade, belt component costs, pumping costs and the cost of overburden removal and reclamation. In most cases in Appalachia, especially in eastern Kentucky, the observed transition depth ranges from 20 to 30 m (66 to l00 ft). This indicates that actual practice is consistent with the analytical approach used.

Jan 1, 2002

By Mark L. Blanford, Roger M. Zimmerman

INTRODUCTION Volcanic tuffs on and adjacent to the Nevada Test Site (NTS) are being considered by the Department of Energy (DOE) for the possible geo- logic disposal of high-level radioactive wastes. The Nevada Nuclear Waste Storage Investigations (NNWSI) project was established in 1977 to evaluate such disposal. Sandia National Laboratories (SNL), one of the participants in the NNWSI project, has as one of its responsibilities the development of a rock mechanics program for the Nevada site. SNL conducted three small-diameter heater experiments in welded and nonwelded tuffs in G-Tunnel on the NTS, to investigate the thermal (heat transfer) and hydrothermal (thermal- induced water migration) behavior as part of the rock mechanics program. These two aspects were investigated to increase knowledge about the behavior of tuff so that predictive capabilities are available for use by repository designers, waste-package designers, and performance analysts. Also, knowledge of the behavior of the tuff is invaluable for planning and designing future in situ experiments at Yucca Mountain, the candidate site for the repository. The evaluations of these three experiments is the subject of this paper. Designers, analysts, and experimenters are seeking a better understanding of the behavior of tuffs under the influence of thermal loads expected from radioactive-waste storage, because of two physical features peculiar to tuffs. First, tuffs are inherently porous because of the manner in which they are deposited (Smith, 1960). Tuffs utilized in G-Tunnel testing have porosities ranging from 15 to 46%, which cover the ranges of expected porosities in the target horizon at Yucca Mountain. It has been established that the G-Tunnel tuffs have similar bulk, thermal, and mechanical material properties to those at Yucca Mountain (Zimmerman et al., 1984), thus, G-Tunnel testing can be used to evaluate the effects of porosity on the thermal and mechanical behavior. The second feature is that tuffs above the water table contain pore water that influences the thermal properties of the rock; displacement of the water must be accounted for in repository designs and analyses. For example, G-Tunnel tuffs, located some 600 m above the static water level, have saturations in excess of 60%. Similar percentages are expected at the target horizon in Yucca Mountain (Zimmerman et al., 1984). The presence of and the removal of the pore water affects the thermal behavior of the tuffs, and these three experiments were designed first to determine the phenomenological behavior and then assess influences on predictive capabilities. The focus in this paper is to present the results and evaluations of the experiments as they apply to improving predictive capabilities. The thermal aspects are emphasized by comparing the measured temperatures (in and around heater emplacement holes) with calculations of predicted temperatures using numerical models, so that the effects of significant parameters can be evaluated and integrated into future predictive models. Observation of the hydrothermal aspects is needed to assess the effects of loss of pore water and subsequent migrations on the temperature fields during the heating, and also to define the expected environment in the vicinity of the outer metallic surface around the waste. The metallic boundary can be either the outer shell of the waste package system, which is the main engineered barrier for waste containment, or the borehole liner. A final decision has not been made as yet about the necessity for lining boreholes; thus, the emphasis is on predicting the characteristics of the environment around the outer metallic surface. Two aspects that limit the scope of this paper are (1) the experiments were performed at a smaller than canister scale for the purpose of

Jan 1, 1986

This paper presents the development of a knowledge based integrated decision support system (E.X.I.S) for the extractive industries to provide information concerning the environmental impact of extractive operations on land quality, surface and ground waters, and the best solutions for the rehabilitation/revegetation of the waste disposal areas to the relevant target groups (extractive industries, regional authorities, national authorities, research institutes, public). GIS was integrated with the decision-making models for the rehabilitation and revegetation of mine spoil. The system design involves several steps including site selection ? mine type identification ? waste identification ? selection of rehabilitation (revegetation or other methods). The knowledge based model consists of two integral parts: the model base, in which the input data are processed and classified using special fuzzy algorithms and criteria and the knowledge model, which hosts the various decision algorithms concerning evaluation of vegetation covers, selection of trees and plant species, selection of rehabilitation and revegetation schemes and also economic analysis for each option. The system input will include parameters on site characteristics (climate, topography, geology, hydrology etc), waste type and properties (physical-geotechnical and geochemical data) as well as environmental parameters of the existing waste disposal area. Based on the values of the above parameters and the characteristics of the rehabilitation technologies developed worldwide, the system, using IF-THEN rules will define a list of appropriate techniques for the rehabilitation of the examined waste. Then, the model will involve the application of multi-criteria analysis (MCA), i.e. a structured system for ranking alternatives and making selections and decisions. Each technique shall be judged based on its behavior into four fields, i.e. financial, social, technical and environmental criteria. In turn these fields will be analyzed into a lower level of evaluation criteria.

Jan 1, 2006

By Kambhampati C. Rao, Cecil Lue-Hing, Nabih P. Kelada, William B. Willborn

improvements in the analytical techniques for cyanide speciation can furnish useful information about the behavior of the different cyanide species in the receiving environment. This could be of help to the environmentally concerned public and the regulatory agencies in the assessment of cyanide limits for effluents, stream quality, and land disposal of cyanide bearing wastes. In addition the ability to distinguish the free cyanide and the weakly bound cyanide from the strong ULTRAVIOLET IRRADIATION UNIT (LAMP, COIU3' HOUSING) FIGURE 1 complexes, as well as transformation to thiocyanate is also needed by different industries, such as mining and metal finishing, etc., to evaluate the efficiency of several processes. Cyanide has been used for the recovery of gold since the late 19th century. Although cyanide leach solutions are mostly recovered and used again, a large quantity of cyanide bearing wastewater becomes unfit for use and has to be treated before it can be released into natural waterways.

Jan 1, 1992

By C. M. Chang, H Gu, J. A. Barrera-Godínez, T. J. O’Keefe

The inability to economically separate Fe3+(aq) from a variety of liquid effluents is a major Concern for the primary metals industry. A unique solvent extraction process, galvanic stripping, has been developed to address this problem. The galvanic stripping of iron from D2EHPA using only a 5~10 g/L H2SO4 solution is achieved after Fe3+ is directly reduced to Fee, in the organic phase using zinc metal additions. To date, the primary focus of the laboratory research has been on optimizing the parameters that control iron removal. The results from these studies have now been, used to make a preliminary design for a continuous flow process that is envisioned for zinc industrial applications. Specific quantitative data are shown for the use of a Zn-Ph cellos° in the iron-reams al process. Some introductory results on electrochemical potential measurements and impurity distribution with solution cycling are also giiven.

Jan 1, 2000

By D. E. Munson

To assure the safety of a radioactive-waste repository, the performance of the repository must be predicted far into the future. The Waste Isolation Pilot Plant (WIPP) Program is responsible for developing the technology for such performance predictions in bedded salt. An important technology-development activity concerns the, fielding of very large-scale in situ tests to determine the time-dependent deformation of underground openings in salt as a basis for validation of the predictive technology. This technology is necessary to predict repository seal performance and final closure times of rooms and may be of value to the salt and potash mining community, as well.

Jan 1, 1992