Search Documents

By William G. Pariseau

The purpose of this paper is to present a design procedure for the quantitative estimation of support load requirements in underground mines. Emphasis is upon the basic features of support behavior common to a large variety of support systems-bolts, timber sets, stope fill, steel arches, concrete liners and so forth. A strong reliance is placed upon fundamental principles and modern computing techniques for their quantitative implementation. Example problems illustrate the approach. Where artificial support is required, the ground in the vicinity of the face usually stands unsupported long enough for the support to be installed. At the time of installation, the load transferred to the support from the adjacent rock is essentially zero, although in some cases there may be an initial set load, for example, from timber blocking. With the passage of time and advance of the face, ground motion loads the supports. If the support system is properly designed, then the additional loading poses no threat to the safety and productivity of operations. If not, then difficulties may arise including high maintenance costs, hazardous work conditions and reduced productivity. Of course, over-design can be equally wasteful. Quantitative estimation of support loads is therefore essential to overall efficiency in mining.

Jan 1, 1975

By Kevin Fitzpatrick, Carmen Scalise, Patrick Jensen

"The Metropolitan Water Reclamation District of Greater Chicago (MWRDGC) owns and operates the Tunnel and Reservoir Plan (TARP) system which was adopted in 1972. TARP is a network of 110 miles of deep tunnels and ultimately 3 large reservoirs to combat waterway pollution and flooding within a 350 square mile area served by combined sewers. The original TARP concept included additional tunnels to convey CSOs from the largest storms to the reservoirs. With the initial TARP tunnels complete and the reservoirs nearing completion, MWRDGC commissioned hydraulic and hydrologic modeling studies to analyze the benefits of additional conveyance tunnels. These updated studies optimized the configuration of additional tunnels considering integration with potential future local sewer system upgrades. The alternatives considered several routes of 25, 30, and 35 foot diameter tunnels, ranging from 10 to 18 miles. Alternatives were analyzed based on projected reductions to basement flooding compared to the relative costs. TUNNEL AND RESERVOIR PLAN After World War II the Chicagoland area underwent rapid growth and development. With the Metropolitan Water Reclamation District of Greater Chicago's (MWRDGC) service area becoming increasingly impervious, the flat Chicago landscape was increasingly at risk of significant flooding. In the mid and late 1950's, Chicago experienced multiple extreme storm events that had significant impacts on the city and generated the momentum necessary to initiate what would ultimately become one of the world's largest civil works undertakings. In 1957 a Flood Control Coordinating Committee was formed, consisting of representatives of the MWRDGC, Illinois Department of Public Works, Cook County, and the city of Chicago, to review various plans and develop recommendations for a course of action. With more than 50 alternative concepts being identified, the Tunnel and Reservoir Plan (TARP), which itself is a composite of various alternatives, was adopted the by the Metropolitan Water Reclamation District of Greater Chicago (MWRDGC) in 1972. The need to adopt a long term plan was further influenced by the Clean Water Act, which was enacted only 8 days prior."

Jan 1, 2016

By James J. Scott

Longwall mining has not received a great deal of attention in the United States; however, this system offers many advantages over the conventional room-and-pillar methods now being used. In order to conserve the coal resources of this country, the U. S. Bureau of Mines has investi¬gated the feasibility of adapting European longwall mining methods to American coal seams. Their studies showed longwall mining to be well suited to thinner seams and, greater depths; and, in addition, permitted almost 100 percent recovery of the coal. Most, experiments with this method resulted in higher overall production-costs than were commonly obtained with highly mechanized room-and-pillar techniques This high cost-was largely due to the excessive amount of labor required to maintain adequate roof support with conventional longwall mining techniques. With the substitution of hydraulic-powered, self-advancing roof support systems for conventional supports, this excessive labor cost has been decreased, and longwall mining costs are now competitive with those of modern room-and-pillar mining.

Jan 1, 1964

By Joaquin Marti, Peter A. Cundall

This paper reports on some recent work in which several schemes were developed to model jointed rock under high stress, with particular reference to the phenomenon of "block motion" observed during dynamic loading of underground structures. Three approaches were made, corresponding to an increasing relative importance of internal block deformations as compared to rigid block movements. The first one uses distinct element method and assumes internally rigid blocks, which can break, repeatedly, whenever an empirical crack criterion is met. In the second approach each block is allowed three degrees of freedom to deform internally. The third approach, still in the development stage, permits arbitrary deformation of all blocks, which are internally decomposed into finite-difference zones and automatically rezoned during slip to preserve the calculation accuracy on joints. The last two schemes allow arbitrary constitutive relations for the intact rock, and all three schemes permit the geometrical arrangement of joints to be arbitrarily complex, in contrast to normal Lagrange, finite-difference programs, which are unsuited to model discontinua.

Jan 1, 1979

By Karl S. Vorres

Coal my not seem like it, but it is a perishable commodity. The basic coal scientist cannot always replicate earlier experiments with a given sample because of changes that have taken place in the sample. This has led to a stated need for stable samples Coal looks like a uniform black solid to many people, but it does vary in its composition from state to state and mine to mine it also can be shown to vary significantly within a mine or seam. These variations have led to a stated need for consistent samples.

Jan 1, 1985

By Peter Van deVelde

Many companies in North America because of economic or environmental reasons are considering reprocessing material from their waste ponds. The Japanese have developed highly specialized machines and techniques to reprocess industrial/mining wastes from settling ponds. This paper discusses the techniques and results of applying this technology to North American applications.

Jan 1, 1983

By Lawrence A. Taylor

The rocks and minerals of the moon will be included among the raw materials used to construct a lunar base. The lunar regolith, the fragmental material present on the surface of the Moon, is composed mostly of disaggregated rocks and minerals, but also includes glassy fragments fused together by meteorite impacts. The finer fraction (i.e., < lcm) of the regolith, the soil, is probably the most important portion of the regolith for use at a lunar base. For example, soil can be used in bulk as insulation against cosmic rays, for lunar ceramic and abodes, or for growing plants. However, beneficiation of the soil can provide other feedstocks. For example, the soil contains abundant solar-wind implanted elements, as we1 1 as various minerals, particularly oxide phases, which are of potential economic importance. These components of the soil are sources of oxygen and hydrogen for water and rocket fuel, helium for nuclear energy, and metals such as Fe, Ni, Al, Si, and Ti. The uses of the lunar materials only await a fertile imagination.

Jan 1, 1990

By M. Karmis

The Virginia Center for Coal and Energy Research is leading an interdisciplinary coalition to identify potential carbon sequestration sinks in unmineable coalseams as part of the U.S. Southeast Regional Carbon Sequestration Partnership. The Virginia Center for Coal and Energy Research and the Eastern Coal Council are leading education efforts for the project, as well as specific outreach efforts in Central Appalachia in order to develop a process for stakeholder education and engagement in sustainable energy.

Jan 1, 2007

By R. Hogg, T. F. Dumm, L. G. Austin

The applicability of SEM/EDS techniques to particle-by-particle analysis of respirable coal dust is evaluated. It is demonstrated that the correction procedures needed to account for the failure of most EDS systems to detect light elements (especially carbon) become unreliable for particles in the respirable size range (< 10 µm). Other serious limitations arise from x-ray counting errors for coal particles with low but significant mineral content and particle counting errors for liberated mineral matter.

Jan 1, 1991

By J. D. Miller

Reaction kinetics for gold dissolution in acid thiourea solutions were investigated using formamidine disulfide as an oxidant. For the conditions studied it appears that a surface reaction limits the rate of gold dissolution. The rate was found to be first order with respect to thiourea concentration and half order with respect to the concentration of formamidine disulfide; the apparent activation energy for the reaction was 10.40 kcal/mol (43.40 kJ/mol); and the reaction rate was independent of pH for the pH range 1.0 to 3.0.

Jan 1, 1999

By K. Terhaar, K. Prisbrey

The objective was to determine operating protocols for a lead and silver column flotation cleaner being considered for installation at Sunshine Precious Metals Inc. &apos;s Kellogg mill in Northern Idaho. In this column, tetrahedrite and galena were floated, and pyrite and other gangue minerals, including siderite and silica, were depressed. The procedure was to develop a dynamic simulation using a linear transfer function approach. The transfer function related cause-and-effect variables such as the influence of collector and depressant dosages on recovery and grades. Bench-scale flotation tests followed by pilot column testing provided the data used to develop a linear transfer function. The transfer function was derived using a spreadsheet. This model was applied to simulate how the flotation column could be made to respond to disturbances in feed grade. The results were that xanthate, zinc sulfate and sodium cyanide were found to be suitable controls for grade and recovery. Simulations showed the best sequence of manipulations of these reagents, and these sequences are useful for future operator training. The conclusion was that linear transfer functions were able to simulate lead and silver recovery, develop scenarios for operator training and provide a foundation for future on-line control.

Jan 1, 2002

By S. Hicks

This technical note describes an alternative procedure that can be used in linear programming calcula¬tions where the compliance limit of lbs S02/million Btu for the blending coal is subject to change. Dr. Mateer in his technical note titled "Coal blending for sulfur compliance" (ME, September 1994, p. 1103) defined an "excess sulfur" parameter that provides a valid constraint equation for a linear program optimization. The coals used by Dr. Mateer in his examples are shown in Table 1. To create the parameters for the constraint equa¬tions to blend to an SO2 content of 1.2 lbs S02/million Btu; the excess sulfur for Coal A was defined as Sulfur excess%o = 0.5 - 0.6-13,000/10,000 = -0.28 This equation was used to create the constraint equation -0.28A + 0.44B + 1.36C<- 0.0 Another way to create the parameters for the constraint equation is given below. In these equations: ? W is the total weight; ? A, B and C are the fractional proportions of each potential blend stocks; ? Sa, Sb and Sc represent the percent sulfur content of the blend stocks; ? Ha, Hb and He represent the calorific content of the blend stocks in Btu/lb; and ? H and S represent calorific and sulfur contents of the composite blend. The weight of blend to produce one million Btu is [ ]

Jan 1, 1997

By Heinz Distelmeier

Short Historical Review Tunnelling in Germany is as old as it is in other industrial countries. Until the middle of this century German contractors had no chance to work continuously in this business except if they were operating internationally. Since 1960, however, tunnelling has been a growing market domestically. The reasons for this growth have been both in the growing demand of traffic routes and also in an increasing environmental consciousness, which tries to transfer any cause of disturbance underground. Tunnelling engineers of course don&apos;t complain about this trend. As almost every German city is built upon water-bearing soft ground, shields have been used soon after they were first successfully utilized in Great Britain and the United States. Until the seventies lining systems for shield tunnels were predominantly either cast iron segments or concrete segments for primary support combined with different sealing systems and a secondary concrete lining cast-in-place. Steel ribs and timber lagging for primary support has not been utilized in Germany, since the owners don&apos;t accept timber to be left in the ground. In 1973, for the first time, permanent linings were constructed with watertight segment rings of precast concrete (Fig. 1). This lining was developed as an economical solution for use with slurry shields in noncohesive, water-bearing soils that required an immediately watertight lining. Extruded linings have a similar effect, although these still need a secondary lining

Jan 1, 1987

By R. K. Mehta

A review of the literature reveals that methods for simulating the coupled behavior of size reduction and liberation are limited to binary mineral systems containing one composite particle class. The aim of this paper is to describe the development of a mathematical model to simulate such behavior for binary and ternary systems containing multiple classes of composite particles. A modified Levenberg-Marquardt algorithm and a finite difference Jacobian are used in conjunction with the developed model and a set of constrained equations to estimate all kinetic parameters. This estimation scheme is validated for a binary ore (sphalerite-dolomite) with five composite particle classes using experimental data.

Jan 1, 1989

By E. K. C. Chanda

The best use of available reserves to give good metal recoveries relies on short term mine production scheduling.-The aim is usually to produce a plan to guide mining in specific areas that will enable mine operations to deliver the budgeted tonnes and grade to the mill and keep within the long range mine plan. Thus, short term production scheduling is an important aspect of the open pit mine planning function. Since the 60&apos;s increased attention has been paid to effective production scheduling as a means of improving the economic viability of existing mines. Hence, mine scheduling scheduling systems have been evolving rapidly during the last two decades. These systems include manual techniques, computer based simulation, mathematical programming and more recently Computer Aided Design (CAD). Some general drawbacks of the current scheduling systems are that firstly, the costs of acquiring and using them are not at all insignificant especially for small to medium sized pits. Secondly, there is an inherent trial-and-error aspect in these systems. Thirdly, they tend to be suited for specific orebody geometries, hence lacking the necessary generality. For instance, the use of computer programs for planning open pits to mine stratiform orebodies raises problems which are not usually met when massive orebodies are considered. There for, a need exists to develop simpler but effective short term pit scheduling procedures suitable for stratiform type orebodies, considering their geometry and geology. This paper describes a PC- based model designed to assist the planning engineer in optimizing the short term production schedule in open pit mines with stratiform orebodies. The model is based on a combination of linear goal programming and deterministic mining simulation. The orebody model is made up of ore and waste mining regions where winning and and/or stripping are taking place. These shovel regions form the basic planning elements in the model. This approach does not require the laborious preparation and use of a regular block model. The computer program consists of main modules: (i) Data capture - processes the raw data into the required format for mine planning. (ii) Precedence mining constraints - checks the status of each shovel .region at the beginning of a given scheduling period with regard to geometrical mining constraints such as undercutting. (ii) LP- Optimization - provides an optimal selection of ore shovel regions which do not violet geometrical constraints for mining in the period, the objective, being to maximize the contained metal equivalent in the blended R-O-M ore and at the same time to minimize deviations in grade and tonnage from the call values. (iv) Post LP-Simulation - enables the user to smooth out the LP solution in order to adjust it to a practically executable plan and simulates mining of ore and waste for the period. Shovel allocation to selected ore and waste shovel regions, unit operations and depletion of reserves are executed in this module. Preliminary testing of the model for monthly production scheduling using data from Nchanga OPen Pit on the Zambian Copperbelt indicates that it can be a useful planning tool and gives acceptable results.

Jan 1, 1992

By Charles A. Ramsey, Kathleen S. Smith, Philip L. Hageman

We developed a statistically based strategy for sampling the surficial material of mine-waste dumps for use in screening and prioritizing historic dumps on abandoned mine lands. This sampling strategy entails the collection of a representative composite sample from individual dumps and allows for regional or watershed-based assessments. One 30-inment dump-composite sample collected using this sampling strategy contains as much information, relative to average value, as 30 individual grab samples at 1/30 of the analytical cost.

Jan 1, 2000

By Ronald K. Frobel, Christopher J. Wienecke

Geomembrane systems and associated geosynthetics such as geotextiles, geonets, geogrids and geocomposites have been used in precious metal heap leach and tailings facilities for many years. Geomembranes have been used in the heap leach process in pad design and solution recovery ponds as well as associated collection channels as the primary liquid barrier to contain and collect metal bearing leach solution. Geomembrane systems offer an effective, low cost alternative to other containment methods such as compacted low permeability soils, asphalt or concrete. In the 19BO's, rigid High Density Polyethylene (HOPE) liners were used to a great extent with a gradual transition to the use of the more flexible Very Low Density Polyethylene (VLDPE) and Polyvinyl Chloride (PVC). These three geomembrane systems have been used successfully in precious metal heap leach solution containment. Predominant material thicknesses have been 30 and 40 mil for PVC, 40 and 60 mil for HOPE and VLDPE. Variants in recent years have included roughened HDPE and VLDPE to provide higher surface friction characteristics, as well as newer polymer materials such as polypropylene. In addition to providing an economical method for providing enhanced solution recovery, geomernbranes are also providing the primary liquid barrier for prevention of groundwater contamination. Because heap leach solution chemical components and dissolved metal constituents are classified as toxic substances, they are subject to environmental regulation. Many regulatory agencies are still developing guidelines for heap leach pad design, however a geomernbrane liner system is often used as a single liner or in conjunction with other materials to form composite double or even triple lined systems. "Other" materials can include alternate layers of drainage aggregate, geotextiles, clay layers and other geomembrane or geocomposite layers.

Jan 1, 1993

By D. W. Dew, D. M. Miller, P. C. van Aswegen

The bacterial oxidation (BIOX®) process for pre-treatment of refractory ores for gold recovery is marketed by BIOMIN Technologies S.A. The process was originally developed by GENMIN who are still providing testwork, design and commissioning assistance to BIOMIN. This process offers an alternative to the more conventional roasting or pressure oxidation techniques with the following advantages: • Greatly reduced capital costs for small to medium size plants. • A relatively flexible and easily controllable process requiring relatively unskilled labour for operation. • Improved gold recovery. • A process that is environmentally friendly. The principal disadvantage of bacterial oxidation is the relatively slow kinetics compared to pressure oxidation and roasting, a plant residence time of 4 to 5 days typically being required to obtain complete liberation of gold from refractory sulphide minerals. Bacterial activity is also slow to recover from disruptions such as air supply failure or contamination by toxic species such as cyanide. Optimum plant performance depends on judicious management and sound training of operators.

Jan 1, 1993

By L. M. Klimov

In recent gears in the coal industry a great deal of attention is attached to the questions of elaborating and introducing the problems of planning and management and, first of all, in the sphere of mine production. The basis for planning of mi- ne production is complexes (sets) of problems for planning the development of mining operations based on different time periods, ensuring the follow-up of changes of mine productive capacities. Complexes of problems for planning, the development of mining operations at existing underground and surface mines within the OASUugol system (Coal Industry-wide Automatic System of Management) are aimed at ma- king decisions close to optimum, i.e. general lay-out of panels, blocks and pillars; transport and ventilation networks; schedules for working out parts of mine take; coordinated mining operations with limited labour and material resources; control of mining operations and ultimately maintaining productive capacities of existing mines at the required level.

Jan 1, 1979

By Edward Marszalek, Boleslaw Firganek

The paper deals with a computer method and algorithm of optimization of the rescue routes for the endangered staff in the case of fire in a given place of the mine. The adapted method is based on the objective function and realizes the algorithm of the shorest path with weighers assigned to it. The objective function is so defined that it reflects possibly all the hazards and difficulties arising during a fire in the mine. The algorithm is enhanced by an empirical formula for calculation of the smoke zone as result of a mine fire. The presented results of computations of optimal routes for several simple examples using the canonical scheme of the mine network and simulated fires are satisfying and prove the method, the algorithm and the coded program to be correct. The program will be a part of the software library of the mine ventilation engineer. The data for the program will be updated on-line from the fire detection systems.

Jan 1, 1989