Search Documents

By Boshou Bian

Air quantity is the primary parameter governing the working condition of a mine fan. In order to improve the fan performance and efficiency, reduce its energy consumption, and guarantee mine safety, it is very important to obtain an accurate value. However, generally speaking, the fan ducting or drift on surface is very short in distance and contains sharp bends. The air quantity of the mine is so concentrated in this way that the air velocity becomes very high, and the airflow, either in the fan drift before the fan impeller or at the downstream diffuser, is very turbulent. Therefore, no anemometer is satisfactory because there is too much difference between the measured value and the actual value of air quantity at the mine fan.

Jan 1, 1989

By S. L. Jung, T. L. Nichols, K. Prisbrey

The problem was to evaluate the on-line detection of rock properties through acoustic emission sensors. Acoustic emission sensors, when attached to crushers, grinders, and roof bolters, are robust, economical, and relatively maintenance free. Our objective was to relate acoustic emissions to rock fracture mechanisms, including micropore closures, linear elastic deformations, and crack propagation. We evaluated acoustic emissions from steel jacketed rock cores during indentation tests. In addition we attached sensors to the rotating shaft of a rock bolter drill. A back propagation neural network "learned" rock fracture characteristics and rock type with 99% classification accuracy. A neural network's calibration and computational abilities suggest better acoustic emission sensor capabilities.

Jan 1, 1993

By R. D. Lama

This paper presents the results of a large scale trial of polycrystalline diamond picks (PDC) on longwalls with particular reference to dust control. Results from fixed position monitoring showed that PDC picks produced less respirable dust than tungsten carbide Point Attack picks. Dust generation at the longwall face was lower by 39 - 43%. Field trials also indicated that the life of a PDC pick to be at least 1460 tonnes/pick.

Jan 1, 1993

The present contribution examines the main components of a sustainable land reclamation program applicable to surface coal mines and the environmental threats that hinder the transition to sustainable land management. It compares the main ?waste streams? that cause adverse impacts to the environment with the so-called ?best available technologies and managing practices? that are proposed by organisations with high expertise in land management. Also, it addresses the environmental and socio-economic indicators that should be monitored in order to assess the results of the land management program and to allow remedial actions and continuous improvement. Based on the Greek lignite mines experience in land reclamation, this paper presents the common weaknesses of the land management programmes and proposes an improved communication scheme that moves things towards sustainability. This scheme is based on a more rational exploitation of the available economic resources and a constructive dialog between the mining companies, the local authorities, the state institutions and other stakeholders.

Jan 1, 2003

By D. M. Cregger, J. L. Rosenblad, R. E. Ranken

The construction of a large span, high-walled underground opening in a low strength shale rock is unprecedented. The feasibility of constructing a pumped storage project with several tunnels and a large underground powerhouse in low strength shale rested largely on the feasibility of building stable openings large enough to accommodate the required equipment. Because of the lack of experience with large openings in shale, the decision was made to excavate a test adit and test chamber and conduct a multi-faceted geotechnical evaluation program designed to yield pertinent in-situ data on the ability of the shale to accommodate a large underground opening. Factors considered in the shape, size, orientation, and location of the test chamber were: (1) similarity to the anticipated powerhouse chamber, (2) nature of the most important data to be obtained, (3) feasibility of construction, and (4) economics.

Jan 1, 1983

By K. F. Unrug

Martin County Coal Corp. is located in Martin County, KY, in the Appalachian coal fields, near the West Virginia border. The company's total leasehold covers more then 133.5 km' (33,000 acres). Total annual production at Martin County Coal Corp. is currently 2.2 Mt (2.5 million st). In certain years, though, it exceeded 2.7 Mt (3 million st). About 45% of the annual production comes from two surface mines. The balance is produced from five underground mines. Martin County Coal's work schedule consists of two nine-hour shifts a day, 240 days a year. Topography The topography of the area is characterized by rugged hills and ridges and sharp V-shaped valleys demonstrating a cliff and slope topography. This topography consists of alternating benches of outcrop sandstone and slopes. The deep valleys have been carved out by many small streams in the area. These streams are contained within the steep slopes of narrow, twisted mountain ridges. The ridges are underlain by massive sandstones that, being resistant to erosion, create sharp, rocky morphology. The height of the hills above the valley floors ranges from 122 to 244 m (400 to 800 ft).

Jan 1, 1991

By L. M. Gochioco

The Seismic Interactive Interpretation Workstation (S//W) provides a wide spectrum of utilities ranging from improving field acquisition techniques, data processing and interpretation of coal seismic data. The power of the workstation lies in the interpretation process where various sets of geophysical and geological data are integrated to form a network of information that is stored in a database. Computer models are generated from known borehole and geologic information and later cross-correlated with the processed seismic data. Structural and stratigraphic modeling techniques add another dimension to the interpretation process. Complex trace attributes highlight subtle features not easily observed in black and white sections. Using the computer workstation, the explorationist gains valuable insight and conducts more intelligent interpretation of seismic data through a more comprehensive network of data analysis.

Jan 1, 1992

By K. Hanumantha Rao, K. S. E. Forssberg, H. R. Manouchehri

The responses of calcite, feldspar and quartz minerals in a laboratory free-fall electrostatic separator after tribocharging with stainless steel, PVC and copper plates were investigated. The effects of H3BO3 and BaC12 chemical pretreatment on the electrical properties of the above minerals were examined. The changes in the electrical properties are discussed along with the determined charge, dielectric constant and electrical conductivity of the mineral samples. The electrical properties of the minerals and their responses to the electrical field during separation after tribocharging and chemical pretreatment are explored relative to the electrical behavior of the minerals.

Jan 1, 2000

By Eugene Honeycutt, David Gallagher, R. E. Melley, Nick Madison

Drummond Co. Inc.'s Shoal Creek Mine slope conveyor is the highest lift, highest horsepower, highest tension conveyor system in North America. The system has a capacity of 4950 t/h (5500 tph), a vertical lift of 360 m (1180 ft) and a total connected power of 6000 kw (8000 hp). The mine will include 2 longwall machines and 5 to 7 development sections. Annual raw production will approach 9 million tly (10 million tpy). This paper describes the early investigation of system capacity, haulage system options, and the final selection of a single flight belt conveyor. It will review the basic system de- sign and equipment selected. Also included will be some highlights of the installation of the conveyor system.

Jan 1, 1996

By Charles N. Alpers, Jane M. Hammarstrom, Robert R. II Seal, Nora K. Foley

Geoenvironmental models are compilations of geologic, geochemical, and hydrologic information that describe both the pre- and post-mining environmental signatures of mineral deposits. The environmental behavior of seafloor massive sulfide deposits varies according to deposit type. This study has divided massive sulfide deposits into six categories: (1) Noranda-type, (2) Kuroko-type, (3) Cyprus- type, (4) Bathurst-type, (5) Besshi-type, and (6) sedimentary-exhalative deposits. In addition to Fe and Al, the heavy metals most commonly associated with drainage from these deposits are Cu, Zn, Cd, Pb, and As. Metal ratios of mine drainage and natural background waters tend to reflect the primary character of the ores. Variations in pyrite and pyrrhotite contents are reflected in lower pH values associated with pyrite-rich deposit types.

Jan 1, 2000

The issues involved in mine closure are usually complex, and the risks are significant. Although environmental risks are paramount, other issues such as safety, community, legal, fiscal and technical factors need to he taken into account. This paper describes a simple empirical model based on the concept of the closure risk factor, which will enable decision-makers to analyze the mine closure risks at any site, regardless of the complexity of the issues and the scale, scope and location of the operation. The model enables all the issues to be captured and their individual and collective risk quantified. A number of case studies in Australia and the Pacific that illustrate the usefillness of the model are presented.

Jan 1, 2002

By Harry M. Edenborn, Richard W. Hammack

Experiments were done to determine if a mushroom compost-based sulfate reduction system could be used to treat nickel-contaminated mine waters. Sulfate reduction systems were established in columns containing acid-washed mushroom compost. Simulated mine waters containing 2000 mg/L sulfate and 50 to 1000 mg/L nickel were adjusted to pH 4.5 and pumped through the columns at flow rates between 15 and 25 mL/hr. During the first nine days of operation, virtually all influent nickel was removed in the columns by sorption and ion exchange mechanisms. The nickel removal rate then dropped to 18 to 30 mg Ni/day (7.8 to 12.8 nmol/ g-substrate/day), probably due to low sulfate reduction rates. When sodium lactate was added to the inflow, a sustained and seven-fold increase in the nickel removal rate was observed. Bacterial sulfate reduction rates measured in mushroom compost-based wetlands exposed to coal mine drainage are 2 to 20 times faster than the rates observed in this study. Low sulfate reduction rates in the columns may have been due to the inhibition of microbial activity by high nickel concentrations and the removal of labile organic compounds from the mushroom compost substrate during acid-washing. Results of this study indicate that bacterial sulfate reduction can effectively treat nickel concentrations up to 500 mg/L if labile carbon is nonlimiting.

Jan 1, 1992

By Rowan Melrose, Naj. I. Aziz, Arvind Misra

Mathematical models have been developed to simulate longwall heading development systems in Australian Longwall Mines. The models developed consider the effect of non concurrent cutting and supporting systems and concurrent cutting and supporting systems. They also consider the impact of operating parameters on each of these systems. Operating parameters that are considered include pillar dimensions, the use of surge cars, bolting time, shuttle car speed and heading advance per cycle. The effect of these parameters is considered with respect to production rates and also panel advance rates.

Jan 1, 1996

By Richard C. Fountain

The Central Florida Phosphate District is located in southwestern Polk, southeastern Hillsborough, Manatee, and Hardee Counties, Florida, flanking the.southern end of a major structural uplift known a the Ocala arch. Ore control problems here are varied and unique due to non-homogeneity of matrix and high volume mining operations. Overburden stripping and matrix mining are performed by large draglines, the matrix being slurrified and transported to the processing plants hydraulically. Production geologists' responsibilities include, 1) prediction of special mining problems, 2) prediction of ore quality and quantity, and 3) the physical control of the ore quality and recovery during mining. prediction is based on core drilling and visual inspection and analysis of the core samples. Basic economic, and physical minability criteria are thus established. Ore grade and tonnage recovery are of particular importance with emphasis being placed on coordination between mining and processing personnel. Routine inspection of the working pit face is of prime importance and both physical and quality variations are pointed out to the mining supervision. Physical problems in ore control occur due to erratic clay, dolomitic limestone and sand lenses. Near surface ground water is abundant, posing a threat to recovery. Contaminants of the phosphate ore are large quartz grains, pebbles of cemented quartz sand, clay balls, iron oxide laminac and dolomitic limestone particles. Success of the ore control program is predicated on a balance between predicted ore tonnages and grade and actual production. The geologists' primary attention is directed toward this balance.

Jan 1, 1972

By G. L. Black

Choosing a mining method for an underground ore body is a complicated and often iterative process. Advances in technology give the design team an overwhelming array of possibilities for methods and equipment. Hecla's recent discovery of the deep Gold Hunter ore body has given the staff at the Lucky Friday Mine the exciting challenge of determining the optimum mining method. Taking an ore body from prospect to production requires traditional resource characterization, including drilling, delineating and modeling. Developing the mining plan is an evolving process, changing with each new piece of information as the project progresses through exploration and development.

Jan 1, 1998

By Francis Martino

There are numerous techniques and predictive models used by geologists and mining engineers to define coal reserves and plan mines. The traditional reserve estimation methods commonly used include the isopach, triangular, polygonal, inverse-distance weighting, weighted-moving-average, and trend-surface methods. Geostatistically-based estimation techniques are now being examined by many geologists and mine planners as a superior alternative to these traditional methods. With today's coal mine development costs often exceeding $100 million, and power generation $1 billion, it is logical that a technique that can indicate the degree of confidence associated with a reserve estimate (fuel supply), and thus also the degree of risk, is highly desirable to the coal producer, the financiers, and those desiring to commit to coal utilization under short or long-term supply arrangements.

Jan 1, 1983

By Harold J. Bennett

The Minerals Availability Program is a Bureau of Mines Program to systematically measure and classify identified worldwide nonfuel mineral resources according to their respective extraction technology, economics, and commercial availability. The program is designed to identify, collect, compile, and evaluate information on worldwide active mines as well as on developed and explored mineral deposits, and on mineral processing plants. Objectives are to classify domestic and foreign resources, to identify by cost evaluations resources that are reserves, and to prepare analyses of the availability of these resources for 34 commodities and secondary minerals. Availability analyses consider such factors as geographic location, the type of producible material, the technology and time required to produce a marketable product, and the productive capacity and unit cost for each deposit. These factors, reflected in the aggregated tabular and graphical data in the study for each commodity, are developed for consideration in the formulation of both domestic and foreign mineral policy. To date, the data have been collected for the 34 commodities and the availability analyses are in various stages of completion; expected first cycle completion date for all 34 is early 1986. Raw and aggregated data are available to the public in the form of computer-generated listings, tapes, and maps as well as in published reports. Also, systems developed to assist in performing the engineering and economic c analyses, including the computerized economic evaluation program (MINSIM) and the cost estimating system (CES), are available.

Jan 1, 1984

"There’s no fast way to add more than four miles of track, most of it underground, to the Sound Transit Link Light Rail system in the Seattle area. But increasingly busy traffic through a number of neighborhoods made it necessary. That’s the challenge a joint venture of several tunneling contractors faced when starting its portion of the $1.9 billion Northgate Link Extension in 2013, and the project is still keeping them busy three years later. Completion will mean just a 14-minute ride from Northgate to downtown for an extra 60,000 passengers by 2030. The transit lines will join 58 km (36 miles) of new and under-construction light rail lines running north, east and south from Seattle.Voters, tired of long commute times, approved the project, a key part of Seattle’s regional mass transit system, in 2008. The extension is part of a plan adopted by the Sound Transit board in 1996 to connect the region’s major activity centers. The Northgate project is meant to relieve one of the area’s most congested traffic areas by connecting the Northgate, Roosevelt and University District neighborhoods to existing routes including downtown Seattle and SeaTac airport.Sound Transit dedicated more than a quarter of the project’s estimated expense — $440 million -— to general contractor JCM Northlink LLC to handle the tunnel segment. JCM is a joint venture formed in 2013 between Jay Dee Contractors of Livonia, MI, Frank Coluccio Construction of Seattle, WA and Michels Corp. of Brownsville, WI. The contractors regularly collaborate on large-scale projects and brought experience working on a different section of the extension they completed in 2013.JCM project leaders knew immediately that the schedule would be demanding. They had to work around the clock, six days a week to meet deadlines. The extension runs through highly populated areas, meaning contractors had to follow strict city noise restrictions between 10 p.m. and 7 a.m. Plus, supervisors needed to manage the scheduling of nearly 250 employees to keep work running smoothly.“We had eight different operations and four different subcontractors trying to work in one tunnel,” said Chris Wood, JCM site project superintendent. “It’s important that we keep work linear. That’s the biggest challenge: keeping a path in and out so you can pour concrete, keep electricians and carpenters going, and accomplish everything else.”"

Jan 6, 2018

By R. Perez

The consumption of grinding media forms a significant part of the operating cost of a mineral processing plant. An estimated half billion pounds of steel in the USA and over one billion pounds in the world are consumed each year in wet grinding alone. However, there is some conjecture as to the interacting roles of abrasion and corrosion. In order to provide a more complete picture of the conjoint action of abrasion and corrosion, marked ball tests were conducted on different grinding ball compositions in a laboratory ball mill and the metal losses were measured on varying the conditions, i.e., pH, PO2, in wet grinding a Cu-Ni gabbroic rock and compared with taconite grinding. Ball wear rates ere discussed with respect to ball composition and microstructure and the varying conditions used in the grinding tests.

Jan 1, 1984

By J. A. Finch, Zhenghe Xu, Z. A. Zhou

The generation of microscopic bubbles by cavitation may enhance particle-bubble attachment and improve flotation performance. It is shown in this paper that tiny bubbles or cavities can be generated by strong shear and turbulence in high speed liquid flows. These conditions create the necessary pressure fluctuations in the bulk water to cause the local pressure to drop below a critical value. The formation of bubbles is favored by high dissolved gas contents to promote gas diffusion into the cavities, and by the presence of surfactants to provide some mechanical strength due to the adsorbed film. Experimental results on bubble formation by cavitation and consequent flotation of fine silica (d50 = 1.6 µm) are presented.

Jan 1, 1995