Search Documents

By M. L. Young, M. S. Klima

Hindered-settling columns are used throughout the minerals industry for both size and density separations. In this study, the performance of a continuous laboratory-scale hindered-settling column was evaluated for various particle systems. The test variables included solids composition, water rate and column height. Column performance was evaluated using partition curves and corresponding performance parameters.

Jan 1, 2000

By Steven J. Schafrik, Michael Karmis, Zacharias Agioutantis

3-D or pseudo 3-D visualization of orebodies and mining related processes such as loading and tramming, are now commonly used by the mining industry. An approach is presented that can aid the engineer in creating the visualizations necessary for accurate presentations for use in public relations, safety training, production projections, reclamation plans, etc. It is shown that the creation of such digital representations of mining environments are independent of the mining package used to create the original mine design. Once a proper model has been created, any view of the areas is possible. These views can be taken from any number of stationary points or entered into an animation showing the progress of a mining construction. The paper focuses on the presentation of the steps used to accomplish the visualization and an example is for a quarry fill placement project.

Jan 1, 2002

By R. C. Berry

The Environmental Impact Statement (EIS) has become a routine requirement for mining operations on federal lands. A similar document is being required in developing countries. Baseline studies are needed prior to writing an EIS and these studies involve surface water, groundwater, air quality, and wildlife/ native plant evaluations. The required baseline hydrology and geochemical studies are often the most expensive and lengthy evaluations. This paper summarizes the hydrology and geochemical baseline studies required for .An EIS and presents suggested methods to expedite these studies and to shorten the time and the cost to complete the studies and the EIS.

Jan 1, 1999

By A. Shakoor, A. M. Hirt

The compressive strength of coal, and its variation within and between seams, was determined for four Pennsylvania coal seams (Pittsburgh, Sewickley, Upper Kittanning and Lower Kittanning). Large coal blocks were obtained from 12 coal mines (three mines per seam) and cut into 50-mm (2-in.) cubes using a low-speed saw. The cubes were tested for compressive strength, with the results used to compute actual pillar strength. Using the tributary area approach, the pillar stress was determined. The pillar stress and strength data were used to calculate the factor of safety against pillar crushing for each mine. The cube strength was also correlated with various physical and chemical coal properties (density, percent absorption, percent ash, percent sulfur and percent carbon) to see if any strong relationships exist. The coal's mean compressive strength varies from 9.1 MPa (1326 psi) in the Lower Kittanning seam to 37.8 MPa (5480 psi) in the Pittsburgh seam. Between different seams the pillar strength varies from 29.5 MPa to 48.1 MPa (4282 psi - 6981 psi). Although coal strength appears to be weakly related to carbon content, no relationship was found between compressive strength and other physical or chemical properties. Since the values for the safety factor against pillar crushing generally exceed the recommended value of two, the existing pillars are mostly overdesigned. This implies that an accurate assessment of coal compressive strength could result in the use of smaller pillars and, thus, increased coal production.

Jan 1, 1993

By C. Douglas Lee

This case study describes the work done at the University of Arizona on the development of a computer mine model for an irregularly shaped and spotty ore deposit. The purpose of the work was to develop techniques for modeling any highly irregular deposit, for which the regular 3D fixed block model is not well suited. The deposit contained complex geology consisting of sedimentary beds that had been faulted, thrusted, and intruded by igneous rocks (see Fig. 1). The physical dimensions of the modeled ore body were 1067 m (3500 ft) along the N-S direction and 914 m (3000 ft) along the E-W direction. Topographic relief in the modeled area was approximately 274 m (900 ft). The highest grade of ore was found near the surface with mineralization extending down to approximately 152 m (500 ft) below. Using a fixed bench height of 12 m (40 ft), the model required 25 levels with the highest elevation being at 1286 m (4220 ft). Fig. 2 shows a cross section of the developed computer model of the ore deposit. The particular modeling approach selected for this deposit was the 3D irregular block model.* This meant that only the dimension of bench height was fixed at 12 m (40 ft). Irregular size blocks in the form of polygons were adopted in the model to describe the ore zones and geologic contacts. The following sections of this chapter describe some of the techniques used in modeling.

Jan 1, 1979

By A. R. Garcia, A. S. Myerson, W. R. Ernst, J. D. Carruthers, M. D. Franke, L. H. Hilzik

A method for removing nickel and vanadium contaminants from spent HDS catalysts involves pretreating the catalyst with H2S followed by extracting the metals with an acidic solution of ferric ion. The ferric ion solution alone removes significant amounts of active ingredients, cobalt and molybdenum; however, by pretreating with H2S, the extraction becomes more selective for removal of Ni and V.

Jan 1, 1988

By P. Whincup, T. Showell, B. Marchant, R. Dunne

An oversupply of copper on world markets in the early 90' s, coupled with a decrease in demand, resulted in a "tight" market for the sale of copper concentrate. In these conditions small producers of low grade copper concentrates found it difficult to sell their products. The situation was exacerbated for those producers also having reasonable quantities of penalty elements (e.g. As, Bi). The Telfer Gold Mine bulk copper gold concentrate, produced from treating underground sulphide ore, fell into this category (i.e. 16% to 20% copper, 30% to 35% sulphur and 3500ppm to 4500ppm arsenic). The concentrate sulphide minerals are predominately chalcocite and pyrite. Although a higher grade copper concentrate was attainable a substantial decrease in gold recovery ensued. Under the prevailing market conditions a decision was made to stockpile concentrates pending either an easing of market conditions or alternatively finding an on site method for treating the concentrate to recover both the contained gold and copper.

Jan 1, 1995

By L. G. Austin

Using an instrumented laboratory high-pressure grinding rolls mill, the grinding force, gap dimension, mass flow rate and net mill power were measured for six coals and a crystalline quartz. A technique was developed to estimate the compressive stress-strain curves for compression of the materials in the mill plus the effects of elastic decompression. To reconcile the mill power and grinding pressure results, it was necessary to allow for the energy recovery on decompression. No clear correlation was obtained between the form of the stress-strain curves or the variation of specific mill power factor with the Hardgrove grindability index (HGI), although coals with the lowest and highest HGIs (i.e., 44 and 106) gave results significantly different from the other coals. Feeds below 140 mesh (105 µm) flowed more rapidly than coarser feeds and would not build up high grinding pressures. This indicated shearing and fluidlike properties rather than compression as a locked bed.

Jan 1, 1998

By Ben H. Daud

A computer model has been developed at Consolidation Coal Co.'s Central Engineering Dept. for preliminary economic evaluation of deep coal mine reserves. Since it was first formulated more than two years ago, the model has been used for the following purposes: (1) ranking studies of coal exploration projects, (2) marketing surveys, (3) preliminary sale and acquisition analysis of coal reserves, and (4) parametric analysis in conjunction with detailed feasibility studies.

Jan 1, 1979

By Trevor A. Moss

Installation of equipment and structures at mines often requires mine planners to evaluate unique loading and operating conditions. Consideration of these unusual features is required throughout design and construction and into operation. Most planners understand the necessity of employing sound civil, structural and mechanical engineering techniques to design these structures and equipment. However, the influence of geotechnical factors on the overall progress of construction and operation is less appreciated. Mine operators routinely perform exploratory drilling to define ore deposits. These exploration activities can be extensive and often include provisions for assessment of subsurface conditions as they relate to the mining operation - requirements for ground support. All of these factors are important to the economics of the mine and are well justified. Surface facilities are provided to access and service the mine, and they play an important role in the successful development and operation of a project. Headframes, hoist foundations and shaft collars, in particular, are examples of unique installations encountered at underground mine sites. The design and above-surface behavior of these facilities can be analyzed with the usual fundamental engineering practices employed throughout the engineering professions. However, near surface exploration for the purposes of assessing soil and rock conditions for foundations is often given a reduced priority and less consideration. This article provides an outline of the benefits and importance of performing such exploration. References here relate particularly to shaft headframes, hoists and shaft collars. But the issues raised apply equally to other installations of a similar nature, including milling equipment.

Jan 1, 1992

By Lee W. Saperstein

The Research Council of SME, at its Annual Meeting in Reno, NR, in February 1993, held a Research Forum on Technology for the Future. The Forum's purpose was to find out from the members, particularly those from industry, their opinions on research needed in the mineral industries. Panelists were selected for their breadth of knowledge and connections. Many panelists, in turn, solicited opinions from additional contacts. A similar effort is underway with mineral-oriented schools. A parallel mission has been undertaken by the American Mining Congress (AMC) through its Committee on Technology. In particular, AMC is concerned that the needs of industry be transmitted in a timely way to federal agencies, especially the US Bureau of Mines. This article reports to the SME membership the principal findings of the Research Forum. The article is derived from a full report that is available from SME. Many of the calls for research made during the Forum can be clustered into five broad categories. These categories are discussed in the following sections of this article. However, since the time of the Forum, many reviewers of the full report have noticed that fundamental research was not given much emphasis. The Research Council points out that the Forum was organized around industrial needs. There is a call to the academic and research community to organize a similar Forum. The Council emphasizes that this is not the last word on research needs and that the membership is urged to continue to give ideas and opinions to the SME Research Council. There will be an opportunity at its next meeting during the SME Annual Meeting in Albuquerque, NM, Feb. 22, 1994, for open discussion of this report. Because the opinions were intentionally confined to representatives from industry, the problems portrayed and the solutions sought are from the vantage of an operator. It comes as no surprise that many of the espoused research desiderata seek more efficient or cost-effective outcomes for the various mining activities discussed. The order of the Forum was a straightforward set of mining activities: exploration, evaluation, mining and processing.

Jan 1, 1993

By P. K. Berger, G. T. Lineberry, H. P. Cole, J. V. Haley

Sixty-five simulation exercises were developed for teaching and testing problem solving and decision making skills to miners and mining engineers. The exercises focused on judgment and decision making for preventing and controlling mine emergencies. The structure and field testing of the exercises are described, and sample frames of individual exercises are presented. Empirical data are summarized about the effectiveness of these simulations based on the performance scores of a national sample of miners and mining engineers.

Jan 1, 1994

By William R. Groseclose, Kenneth D. Schoeman

The Buckskin Mountains Tunnel is a key link in the Bureau of Reclamation's Central Arizona Project. The 22-foot (6.7-m) diameter tunnel is being bored in a north-northwesterly direction through volcanic rock near Lake Havasu in western Arizona. The 6.9-mile (11-km) conveyance tunnel will carry up to 3,000 cfs (85 cu m per sec) of water through the Buckskin Mountains as part of the Granite Reef Aqueduct. The water for the project will be drawn from Lake Havasu behind Parker Dam on the Colorado River and pumped some 800 feet (244 m) above the lake to the inlet portal of the free flow tunnel where it begins its 190-mile (300-km) journey to Phoenix, Arizona, and beyond into Orme Reservoir (figure 1). Precast concrete segments are being used as a single system initial support and final lining in the tunnel being excavated by a tunnel boring machine specially designed and built for the job by The Robbins Company. J. F. Shea Company, Inc., of Walnut, California, is constructing the tunnel for the Bureau of Reclamation.

Jan 1, 1976

By A. E. Hall, K. R. Mutama

The wind tunnel has been used extensively for mine ventilation research and continues to be a valuable tool. The advent of the powerful personal computer has reduced the use of wind tunnels because several flow problems car be simulated and investigated quickly. This paper describes the recent design and construction of a wind tunnel which is now being used for mine ventilation aerodynamic research and teaching purposes. The wind tunnel has a square cross section measuring 900 by 900 mm and is 8485 mm long from the entrance to where it joins the fan. The tunnel was designed as an open circuit suction type and is attached to a 7.5 kW variable pitch axial flow fan capable of producing over 6 m3/s of airflow. The entire length of the wind tunnel can be used for flow investigations and all activities are visible since the sides are made of plexiglass. Results are presented from the test program to show that even without honeycombs and screens air flow symmetry is achieved.

Jan 1, 1993

By Pedro Marques Bernardo, Carlos Dinis da Gama

This paper presents a methodology for design and simulation of underground ventilation networks, based on the analysis of real situations, followed by the careful interpretation of the obtained results in order to implement their optimization. The method involves two basic steps: the construction of a complete ventilation data base for the mine, upon a series of care- fully previous surveying studies in order to determine the values of its ventilation parameters, and the simulation of relevant situations for the ventilation system optimisation. A simulation model, modified after the Hardy Cross method, allows the testing of various mechanical means located at different points of the network, aiming to determine the technical-economical feasibility of each solution. These simulations obey the directions of air flow in each point of the mine, as determined by the directions of the natural ventilation flow established in the data base that represents the network. The methodology was validated upon studies developed in ventilation network of the Panasqueira Mine (Portugal), in two situations: regular production (mechanical ventilation) and care- maintenance (natural ventilation).

Jan 1, 1997

By J. M. Scharer, Bruce E. Halbert, Pettit. Carol M., Lysane Bolduc

The ratio of neutralization potential (NP) to acid production (AP) ratio is often employed for predicting acidic discharges from waste rock dumps. The available NP was evaluated in laboratory studies of limestone dissolution in simulated acidic mine water. The available neutralization potential strongly depended on the particle size. Using limestone particles of 114" (6.4 mm) or greater, less than 20% of the total neutralization potential was exhausted at the onset of acid conditions. Apparently, the dissolution of limestone became mass transfer limited. Under mass transfer limitations, the rate of pyrite oxidation may exceed the rate of neutralization by buffering minerals. The implications concerning the controls on limestone dissolution were examined using a geochemical predictive model for sulphide mineral oxidation in waste rock. The results have shown that in case of heterogeneous waste rock piles the NP/AP ratio is a reliable indicator for short-tam predictions only. Kinetic data on the depletion rate of the neutralizing minerals and geochemical modelling suggest that waste rock environments with NP/AP ratios as high as 5.0 may turn acidic in the long term.

Jan 1, 2000

By J. G. Groppo, D. J. Sung, B. K. Parekh

Hyperbaric filtration for the dewatering of fine coal cleaned by froth flotation was evaluated on a laboratory scale. A laboratory pressure filtration procedure designed to obtain a uniform cake structure from dilute slurries containing a significant amount of coarse material is described. Baseline tests were conducted to determine the optimum operating conditions for the eventual application of the process to a continuous pilot-scale hyperbaric filter. Investigated were filter operating parameters such as driving force, time, cake thickness, percent solids, viscosity and pH.

Jan 1, 1996

By T. Y. Yan

An effective elution technique has been developed for recovering uranium from ion exchange resins loaded in the carbonate leaching process. The procedure employs direct elution with acid. In comparison with conventional base elution, the procedure yields eluate of higher uranium concentration, results in a more complete elution, keeps the performance of the ion exchange resin at the fresh stage, reduces acid consumption, eliminates carbonate consumption, and reduces waste for disposal. The technique has been successfully demonstrated in the field and patented. It lends itself to commercialization.

Jan 1, 1987

By H. Huang, J. C. Wu, C. H. Xie, Y. Q. Xue, Z. H. Zhang

Two- and three-dimensional groundwater flow models for dewatering in an opencast mine are presented. The models focus on solving special problems using numerical simulations of the opencast mine. These special problems include the drying up of the aquifer, the movement of the model boundary and the prediction of the residual head. These models are used to describe the decline of groumdwater levels in the Yuanbaoshan Opencast Coal Mine and its neighboring area during the drainage period. The simulated values agree very well with the field data. There have been several successful examples of numerical simulation for predicting the mine dewatering rate in an opencast mine. However, The hydrogeological conditions for the Yuanbaoshan Opencast Coal Mine are rather complex, and the total average flow rate is very high at 4.676 x 105 m3/d (1.65 x 107 cu ft/day). In this paper, a two-dimensional groundwater flow model in a large area is developed to solve the problems mentioned above by simulating regional drawdowns of the groundwater level during the drainage period, and a three-dimensional flow model is developed to simulate the residual head near the open-pit bench.

Jan 1, 1998

By R. L. Wiegel

Several mineral process modeling and simulation packages are currently available for use in evaluating the performance of alternative process flow schemes. A critical link that has been missing from these packages is the ability to quantitatively model the effect of size reduction on the liberation of the valuable and waste minerals in the ore being processed. Although there have been several approaches taken to this problem over the past 25 years, none of them has led to a satisfactory conclusion. A technique was developed for measuring the effective liberation characteristics of magnetic taconite ores, and a program was constructed that makes use of these liberation characteristics in simultaneously simulating both size reduction and mineral liberation as it occurs in tumbling mills. This is an especially important step in the modeling of magnetic taconite processes, where magnetic rejection of low-grade wastes between grinding stages mandates that a predictive capability be available. The current application is specific to magnetic taconite, but it is possible that a similar approach could be used for other types of mineral systems. Key words: Modeling and simulation, Size reduction, Mineral liberation, Taconite, Magnetic concentrator

Jan 1, 2003