Search Documents

By Robert Marks, Enrico Dal Negro, Richard Schulkins

"In July 2012 construction started on the Grosvenor project, a five million tonne per annum underground longwall mine planned for Moranbah in Central Queensland. Grosvenor is located immediately to the south of the existing Moranbah North mine which has been in operation since 1998. EPBM technology is being used for the first time in Australia for excavation of a coal drift. The TBM was used to build two drifts on the project, one for the coal conveyor which will transport to surface, and another for people and equipment to access the underground once the mine’s operational (as shown in figure 1). The TBM will pass beneath a steel archway roof that has been installed at the drift’s entrance and begin drilling into the ground to build the seven metre diameter tunnel, descending at an angle of one in eight until it reaches the depth of the coal seam approximately 160 metres below.INTRODUCTION AND BACKGROUND The first TBM used in a coal mine was in 1962, a Wohlmyer, in Westerholt, Germany. A further 75 km of tunnels were excavated in coalmines within Germany between 1971 to 1983. This paper will review the Grosvenor Mine project (Grosvenor) owned by Anglo American Metallurgical Coal (Met Coal) includes the construction of a new underground coal mine and surface facilities on the northern boundary of the town of Moranbah in the Central Queensland Bowen Basin coal precinct. The contract to undertake the underground development works was awarded to Redpath in 2012. The scope of the Grosvenor Project was to construct temporary office and workshop facilities, install 2 portal arches, backfill boxcuts and infrastructure, excavate by EPBM method 967 m of 1:6 gradient Conveyor Drift and 1,258 m of 1:8 gradient Transport Drift, development of 2,520 m of pit bottom area roadways and development of 10,550 m of the first longwall tailgate. In the following figures 2 and 3, is possible to see the aerial view of the job-site."

Jan 1, 2016

By Qing-Wang Hao

In this paper, the authors attempt to develop engineering based approaches for estimating safety factors against pillar and floor failures and predicting likelihood of subsidence events over abandoned coal mines in Illinois. There are two critical problems involved in the analysis: determination of geotechnical properties, and consideration of time effect. The authors attempt to solve the problems by generating hypotheses, which are used to modify existing engineering models for estimating pillar and floor safety factors. The modified models are validated using data from two well established databases of subsidence events over active and abandoned mines in Illinois. The data analysis suggests that most of the trough type subsidence events in Illinois were caused by floor failures rather than pillar failures. The subsidence incubation period seems to be directly related to initial floor safety factors at the time of mining. This correlation can be used to predict the likelihood of subsidence and to assess subsidence risks within both spatial and temporal contexts where detailed mine maps are available.

Jan 1, 1986

By B. K. Mishra, R. K. Rajamani, R. Venugopal, P. Songfack

Millsoft is a computer-simulation software that predicts the performance of large industrial grinding mills. This software surpasses all other tumbling-mill analysis techniques available today because it is based on fundamental laws of physics instead of empirical correlations. Graphical user interface (GUI) forms simplify the specification of the following design and operating parameters: mill diameter, length, speed, charge density and size distribution, lifter material and geometry. All of these parameters are taken into account in the discrete element numerical technique that constitutes the essence of the simulation software. In turn, the software produces a visual animation of grinding-charge motion, predicts mill power and gives the distribution of impact energy. In this paper, a case study of an 8.5-m-(28 ft-) diam SAG mill is used to illustrate the application of Millsoft for mill design and trouble shooting.

Jan 1, 2000

By John J. Sammarco, Alan G. Mayton, Elaine N. Rubinstein

Researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) developed the Saturn light that significantly improves illumination for roof-bolting machine operators while reducing glare. The existing roof-bolter lighting was the baseline and was compared to the Saturn at 100, 75 and 50 percent intensities. Discomfort glare and disability glare were measured by the De Boer rating scale and the Mars Letter Contrast sensitivity test, respectively. Thirty study participants were tested. Discomfort glare was reduced at least three levels with the Saturn luminaire. Visibility levels were four to 6.5 times better with the Saturn than with the baseline. The Saturn design is freely available for commercialization.

By Stanley W. Ivosevic

Introduction Increasing investor and industrial demand for gold is not being matched by new mine output from traditional sources. This forces the exploitation of alternative natural and industrial resources to supplement traditional sources. A traditional natural resource is either high- to medium-grade ore, of gold or silver with coproduct gold. Or, they are medium- to low-grade base metal ores having byproduct gold. Traditional ores are also frequently extracted at relatively great expense by selective underground mining. Alternative natural resources include low-grade, near surface ores and the products of mining-dumps - and of onsite processing - tailings. Traditional industrial resources are newly mined gold or that obtained from plant sweepings. Their alternative analogues include gold in old scrap and chemical sludges and precipitates, notably those incidental to the electronic industry. These alternative gold resources have several attractions. They are untapped and abundantly available. Having been overlooked by prior metals suppliers, title to many alternative resources is easily acquired. Or, the value of such a resource may go unnoticed until its gold is rendered exploitable by an advance in extractive technology or an other approach. This article addresses the effect of large tonnage, low-grade lode ores on gold supply. Exploiting these ores is rendered commercial by their amenability to bulk mining by modern large-scale mining and metallurgical operations requiring little selectivity. Placer gravels, perhaps the earliest type of gold ore mined, also are bulk minable. But these fall outside the definition of being lode deposits. Most lode bulk mining is from surface open-pit mines. Some, however, is from underground by such large-scale mining techniques as room and pillar, vertical crater retreat, and end slicing. The low-grade gold ore being discussed averages 2.8 g/t (0.082 oz per st). Output How greatly do bulk minable, low-grade resources effect supply? 1982 was a somewhat healthy year for gold mining and exploration in North America in spite of the general depression in the mining industry (Table 1). The wildly fluctuating price of gold bullion had stabilized at an annual aver¬age of $12.08/g ($376 per oz) - (Handy and Harmon base price). Half of the 1.3 kt (43 million oz) of 1982 world gold mined were from South Africa's high-cost, medium-grade, selective underground mines. Of the remaining half, 20%, or about 130 t (4.2 million oz), was mined in North America. This includes Canada and the US - the third and fifth largest gold producers in the world. Of that North American production, more than 62.2 t (2 million oz) of gold, or about 50%, came from bulk mining of gold ores with or without co-product silver. Most of this was in the US, where bulk minable gold-silver lode ore produced nearly 31 t (1 million oz). This amounted to 60% of the nearly 46.6 t (1.5 million oz) produced in the US during 1982. An additional nearly 7.7 t (250,000 oz) of gold were produced as the byproduct of bulk mining of cop¬per ore, for a total of 34 t (1.1 million oz) of gold, or 75% of US gold production by bulk mining. To further illustrate this, US placer, mine dump, and related operations produced an insignificant 4% of US gold output at the time. Exploitation of bulk minable gold deposits is becoming increasingly important worldwide. Most new Australian gold mining announcements are of bulk minable developments. This trend will increase in North American mining as more large tonnage, low-grade operations come onstream in Canada, where much current production is from underground. It will increase with the general climb in Mexican gold mining. And it will grow with expansion of the 12 t/a (400,000 oz per year), gold production of the Dominican Republic. Production Metal price and operating costs make these large tonnage, low-

Jan 11, 1984

By Andrew M. Wala

The determination of air quantity needed to dilute the exhaust gases to a safe level has to be individually evaluated for particular cases. The diesel powered machines are doing some specific operations in the cyclic order required by the technical process. The dynamics of this process in certain conditions has an essential influence on environmental health conditions in the working area. The main purpose of this paper is to show, using computer simulation, how the movement (dynamic) of diesel vehicles effects environmental health standards and also how to determine the required air quantity for certain conditions

Jan 1, 1983

By Y. FUJII, E. CHANDA, J. KODAMA, D. FUKUDA, M. NISHIHARA, Y. NAKAYAMA, P. SINKALA

This paper describes a creep damage model that was proposed to clarify the rockburst mechanism for the Mufulira underground copper mine in Zambia. Cumulative rock damage was evaluated for the edge elements of each sidewall of the mining drives based on normal stresses by the 3-D displacement discontinuity method (DDM) (Crouch and Fairhurst, 1973). The rockburst occurrences were well hindcasted.

Jan 1, 2023

By Charles Stone, Eric Wang

A method for estimating geotechnical rock loads for shallow cut and cover subway stations is presented. Localized geotechnical conditions lead to extreme variations in rock loading on the walls of subway structures. Actual lateral rock stress on these structures can range from near zero to over four times the vertical in-situ rock stress. The primary factors affecting the actual lateral stress are intact and rock mass mechanical properties, excavation sequence, localized tectonic conditions, and potential future adjacent structures. The authors recommend using the AASHTO code value of 65 pounds per cubic foot (10 kN/m3) during concept design, followed by numerical analysis of rock wedges and stress measurement for final design.

Dec 1, 2022

By A. K. Fallaw, D. L. Taylor, G. Wang, L. R. Moore, S. Dobson, C. B. Parkinson

"Over the years, the decline of high grade ores have become an increasing problem in the global mining industry. As such, techniques and chemistries must change in order to continue to meet the market demand and quality. Reverse cationic flotation of quartz and silicates is one of the most important techniques for generating the industry standard product from minerals such as iron and phosphate ores. Amine collectors are the global standard in such processes. However, as the ore quality continues to decline so must the chemistry change to meet the change in ore composition. This paper will focus on the introduction and full scale application of a novel amine collector towards a cleaner flotation process in phosphate beneficiation with Crago process. The results suggests the collector is capable of improving the phosphate recovery, in this cleaner circuit, to approximately 94% with minimal sensitivity to the everyday changes in feed grade.INTRODUCTION The days of mining high grade minerals are long gone, but the demand continues to increase. Phosphate ore, for example, is most dominantly demanded from the agriculture industry as a fertilizer component (i.e. diammonium phosphate, DAP) (FAO, 2014). Some literature suggests that global food production must increase by approximately 70% by 2050 (Cordell, 2009). It is also suggested that the peak global phosphorus production will occur around the year 2033, which is the period at which the easily accessible reserves have been depleted. Currently, phosphorus is commonly mined with a BPL (Bone Phosphate of Lime) concentration of 12-20% and a remainder typically being gangue minerals such as silica, clays, metal oxides, calcareous minerals, and carbonaceous minerals. These gangue components can lead to various negative processing and utilization consequences. Calcium, from carbonaceous minerals, is problematic due to the elevated levels of sulfuric acid required to convert the phosphate rock to the acid form (SRI Consulting, 2009). Calcium can also lead to elevated dosages of flotation reagents due to the desire of the fatty acid to coordinate to calcium minerals. Carbonate leads to increased levels of foam during the wet acid process. Silica is associated with the level of insols (acid insolubles), which must be less than 10% in the final concentrate that will be transferred to the chemical plant for acidification. Phosphate ore can generally be classified as carbonaceous or siliceous (El-Shall, 2003). Siliceous ores are commonly processed through various sizing steps followed by multi-staged flotation (Figure 1) (FIPR, 2014 & Güven, 2010). Though the higher grade phosphate pebble is declining, many mines are still able to size good enough to produce some amount of such pebble. Unlike most metal flotation processes where grinding is a necessity for an optimal process, Florida phosphate flotation does not generally require aggressive grinding and can typically operate at 0.1-1.0 mm. The rougher flotation step applies pH modification to achieve the optimal pH of 8.8-9.3 followed by conditioning with a fatty acid type collector, which builds a hydrophobic waxy layer on the surface of the particle to assist in the flotation. This generally achieves higher than 85% recovery of a product with 50-60% BPL and 15-30% insols. Unfortunately, DAP production generally requires 3.5 tons of phosphate rock containing greater than 63% BPL to produce 1 ton of phosphoric acid (ArgusMedia, 2014). Thus, further purification is required to achieve the grade by the chemical plant for fertilizer production. After the fatty acid is scrubbed off the phosphate particles using sulfuric acid (pH 2.5-3.5), the pH is generally operationally readjusted to 6.5-7.2 by washing with “fresh” water. A second collector is applied prior to the cleaner, which is a reverse cationic flotation process. This collector is typically a cationic amine based reagent, which should have an affinity for silica containing mineral"

Jan 1, 2015

By E. W. Hawk

he power generation industry may be required to reduce carbon dioxide (C02) emissions if regulations related to global climate change are enacted. Coal-fired generation emits more than 80% of the power sector CO2 and would be a likely target for CO2 reductions. Compliance with the Kyoto Protocol will require a 33% reduction from the projected year 2012 emission level, even with moderate load growth. This article describes an analysis of power industry CO2 reduction options and their costs. It assesses how a generator would make compliance decisions under a mandatory CO2 emissions reduction program. Carbon sequestration, fuel switching and new plant construction are considered. The Global Climate Change Treaty signed at the Rio de Janiero Earth Summit in June 1992 set the long-term goal of stabilizing CO2 concentration in the atmosphere. The December 1997 Kyoto Protocol established short-term mandatory targets for the United States and 37 other developed countries. The United States' target is a 7% decrease by 2012 from the 1990 "greenhouse gas" level. Developing countries are exempted from reductions, according to the Kyoto Protocol, despite projections that indicate a significant increase in their emission levels. The Kyoto Protocol must be ratified by the US Senate. US power industry carbon emissions were 490 Mt (540 million st) in 1990 and are projected to be 680 Mt (749 million st) in 2012, according to the US Energy Information Administration. Coal-fired generation emits more than 80% of the power sector CO2. Assuming that the power industry is only required to reduce emissions by a proportional share, a 33% emission reduction, or 225 Mt (248 million st) of carbon, would be required to comply with

Jan 1, 1999

By Irene Bendanillo, Canon Cheung, Justin Lianides, Derek Penrice

The SLAC National Accelerator Laboratory’s two-mile-long particle accelerator generates the world’s brightest X-rays from its Linac Coherent Light Source (LCLS) freeelectron laser. This facility has driven groundbreaking discoveries in medicine and industry. The LCLS-II-HE project will provide a significant increase in laser energy, allowing cutting-edge research in fields including biology and environmental science. A key project component is the Low Emittance Injector Tunnel (LEIT), a 240-foot-long tunnel to be built alongside the existing accelerator and connected to it via a 30-footlong Transfer Tunnel. This paper discusses site and scientific constraints that led to the selection of the LEIT configuration: tunnels to be constructed using the sequential excavation method in mixed-face conditions comprising native rock and placed backfill, and critical design considerations including protection of overlying and adjacent historic structures and structural accommodation of near-fault seismic loading.

Jun 13, 2023

By Sidney A. Hiscock

INTRODUCTION Lead and zinc are today rightly regarded as sister metals. Historically, however, they differ markedly with lead being known and in general use as the metal since 3000 BC in several countries which at that time might have been described as mature economies. Zinc was not isolated and recognised as an industrial metal with distinct and valuable properties until about 1700-1800 AD (although it had, of course, been utilised as a constituent of brass for some 2000 years previously). c were well established as industrial metals by the beginning of the 20th century. The present paper briefly reviews the overall growth in world consumption* and changes in the three main areas which today represent the mature economies or industrialised areas, i. e. ,Europe, the United States and Japan. Trends in overall consumption are determined by the demands for the individual uses for lead and zinc. The changes in patterns of use in the industrialised areas - individually and collectively - and reasons for the changes are also considered. LONG TERM TRENDS - 1900-1984 The World Picture Since the beginning of the 20th century the world consumption of lead (3.9 million tonnes in 1984) has grown almost fourfold and that of zinc (4.7 million tonnes in 1984) is almost eleven times greater than it was in 1900. The long-term trend has been one of continuing expansion for both. metals although the pattern has been severely disturbed at certain periods, for example in the years immediately following the two world wars and at times of marked recessions in industrialised areas. Apart from such major setbacks, new levels of consumption have been established regularly every few years. Recently, however, consumption has not really grown and with only a slow and partial recovery in world industrial activity at present, there is no indication that the peak consumptions of 4.2 million tonnes of lead, set in 1979, and 4.8 million tonnes of zinc (1973) will be exceeded in the near future. The growth in world lead and zinc consumption since 1900 is shown in Figure 1 (which includes changes in copper and aluminium for comparison). Overall growth over the period 1900-1984 has been about two percent a year for lead and about three percent for zinc (annual growth for copper has also been about three percent). Increases in tonnage consumption and growth rates by decade for lead and zinc are summarised in Table I. However, the growth rates by decade sometimes conceal very large individual annual increases and decreases. For example, in 1975 lead consumption fell by 13 percent and zinc consumption by 22 percent compared to 1974. In 1976 consumption of lead and zinc rose by 12 percent and 18 percent respectively. The years when consumption 'landmarks' (ie one, two, three and four million tonnes) were first reached are shown on Table 2. Clearly, the pattern of shorter periods being required to attain each extra million tonnes of consumption was broken in the 1970's. The consumption of zinc overtook that of lead for the first time in 1940, and since 1946 has always been at a higher level. Trends in industrialised areas The two key industrialised areas at the beginning of the 20th century were Europe and the United States which between them accounted for some 95 percent of world lead consumption and 98 percent of zinc consumption. Figures 2 and 3 show the growth in lead and zinc consumption, and Figures 4 and 5 the percentage shares for each area since 1900. Europe has usually been the major user of lead except for some years in the 1920fs, most of the 40's and early 50's when consumption in the United States was larger. In 1900, Europe accounted for about 64 percent of world lead consumption and the United States just over 30 percent. Currently, Europe takes about 40 percent of world consumption and the

Jan 1, 1986

By Lindsey Schneider, Steve Kirk, Michael Miglioretti, Jeffrey P. Kolzow, Kyle White

The US17 Spring/Fishburne Drainage Improvements Project utilizes a stormwater conveyance tunnel system of approximately 8,250 LF. The tunnel system includes two intersecting tunnels of differing diameter at a 40-degree angle. The intersection was constructed in soft-ground conditions. This paper discusses the design, geotechnical concerns, initial ground support, and final lining construction. The tunnels utilized two soft-ground TBMs excavated at 15 ft and 11 ft with ribs & lagging initial support. The final lining consisted of unreinforced and reinforced cast-in-place concrete with polymer fibers. Concrete final lining was successfully completed in March 2020.

Jun 13, 2021

By H. Janas

In a gas/coal outburst the gas plays an active, driving part. The proneness of coal to outbursts can be determined by means of its gas emission properties, since coal that is liable to outbursts differs from coal with normal gas emission properties in that it liberates its gas from the sorptive bond more quickly. There is a risk of outburst when the flow of metha¬ne originally desorbed by the coal is sufficient to move the loosened coal which has been broken suddenly. The violence of a gas/coal outburst can be evaluated from the distance of projection of the mass of coal. It depends on the gas pressure and on the liability to outburst of the coal at the original centre of the outburst. Both factors are complementary in their effects so that the same work is done in a gas/coal outburst when there is a high gas pressure and low proneness to outburst as when there is a low gas pressure and a higher proneness to outburst. The gas pressure in the coal increases with its gas content. Consequently it is possible to deduce the gas pressure of a coal seam from its gas content. In the Federal Republic of Germany the risk of a gas/coal outburst is thought to exist when the desorbable gas content of the coal reaches or exceeds the value of 9 m3/ton and if the specific limit value of the proneness to outburst is exeeded. The Mine Ventilation Testing Station of the Westfalische Berggewerkschaftskasse has developed a new method for determining the risk of gas outbursts immediately after taking the samples at the coal face (1), (2).

Jan 1, 1980

By G. Vogt

Water is one of the most important ressources of our planet. Unlike many other natural resources, water cannot be substituted by anything and must therefore be handled with the utmost care. Depending on the region and the possible shortage of water, the importance of water increases even further. Water consumption is not the only factor. In the construction industry, water pollution from auxiliary and operating materials and processes as well as other contaminants and their resulting load on wastewater play an important role. The sources for wastewater on tunneling construction sites are various: Washing water, seepage water accumulating in construction pits, tunnel water, water used in the slurry circuit in fluid-assisted tunneling methods or water from concrete work and stone cutting all these waters are contaminated with a range of pollutants like solids, hydrocarbons, heavy metals, etc. These contaminants can be removed or treated/reduced with the help of specifically designed wastewater treatment plants (WTPs). After the treatment the cleaned water can be either, in best case, reused on the construction site itself or discharged into water utilities like the available sewer or river pin respecting their discharge requirements. Due to dwindling water resources globally, the continuously rising discharge limits and the ever more important aspect of sustainability the use of WTPs on tunneling construction site will be indispensable. In this paper, it will be presented how these systems are designed and work, what advantages they offer environmentally as well as financially and what to look out for when planning and implementing such a system onto jobsite.

Jun 23, 2024

By S. R. La Brooy, P. C. Earley

Gold and Resource Developments NL (GRD) operates the Macraes Gold Project in East Otago in the South Island of New Zealand, treating a carbonaceous, refractory sulphidic gold ore. The ore is concentrated by flotation, then reground, followed by CIL cyanidation, to minimise loss to the preg-robbing natural carbonaceous material. As the mine has progressed there has been some variation in the preg-robbing nature of the ore, with average overall gold recovery generally in the range 70- 75 %. The Macraes Gold Project has been operating since 1990 and still has an estimated 11 year mine life, which has stimulated the continuing drive to enhance gold recovery. Testwork in 1994 showed there was no improvement in CIL gold recovery after conventional acid pressure oxidation of Macraes Gold Project flotation concentrate. Hence roasting was initially considered as the preferred option to improve gold recovery, being the only established technology to deal with both carbonaceous preg-robbing and sulphide encapsulation. However Newmont Gold Company pressure oxidation technology, as used at Twin Creeks in Nevada, has proved to be applicable to the Macraes Gold Project concentrate. Pilot scale testwork has shown that both roasting and pressure oxidation could achieve similar CIL gold recoveries on the concentrate. However, capital cost, simpler arsenic stabilisation, the ability to operate autothermally at a lower concentrate sulphur grade and simpler environmental consenting factors, has tipped the balance in favour of pressure oxidation. Overall average gold recovery is expected to improve to approximately 84% with adoption of pressure oxidation. GRD has appointed Minproc Limited as EPCM contractor to install pressure oxidation at the Macraes Gold Project, together with upgrading the existing flotation and grind circuits at a cost of NZ$ 30M (US$ 16M). Construction is 60% complete and on schedule for 1 October 1999 start up.

Jan 1, 1999

By Arnolfo A. Valdivia

Prior to 1971, there were several clinical trials to evaluate programs for early detection of lung cancer. Among these, the Philadelphia Pulmonary Neoplasm Research Project,(3) the Veterans Administration Study published by Lilienfeld,(7) and the controlled trial of the Kaiser Foundation Health Plan showed an overall five year survival rate of 8% for newly detected cases (the same as the national statistic for unscreened patients). In 1971, the National Cancer Institute initiated three randomized, controlled mortality studies using lung cancer screening of persons at high risk (male smokers over 45 years old). The studies are being conducted at the Johns Hopkins University Hospital, the Mayo Clinic, and the Memorial Sloan-Kettering Cancer Center. The studies have slightly different designs in the combination of sputum cytology and chest x-rays. At the Mayo Clinic the study group is offered screening with sputum cytology and chest x-rays every four months, whereas the control group is advised to have an x-ray and cytology every year. No reminders are sent, and it is believed that only about 20% of the control group is screened. At Johns Hopkins and Memorial, both experimental and control groups are offered annual chest x-rays. The experimental group is additionally offered sputum cytology every four months.(5) At present all of the programs show that screening can detect cancers that are undetectible by other means. However, at this time mortality rates in the control and experimental groups are not significantly different in any of the three studies. OUR PROGRAM Our clinic is located in Grants, New Mexico and we provide most of the pre-employment physical examinations for the mines operating in the Grants area (Kerr McGee Nuclear, Homestake Mining, United Nuclear, Western Nuclear, and Ranchers). In the examinations, we obtain the previous mining history of the worker, a chest x-ray, a sample of sputum for cytological examination, and a blood sample. We also provide routine annual physical examinations of the workers, with special interest in the detection of bronchogenic carcinoma. In the early seventies, we did not have a definite surveillance program. We did not know whether we should have a program like the one started at Memorial or like the one started at the Mayo Clinic. After long consideration, we decided to have a program that does not demand a sputum cytology and chest x-ray every four months, but that allows as many chest x-rays and sputum cytologies as needed to diagnose lung cancer as early as possible. We believe that, if a screening method for cancer is to be optimally effective, it must detect the process at stages early enough for curative therapy. We order a test depending on the age of the miner, the race, the mining history, the smoking history, the radiation exposure levels, and the results of the previous chest x-ray and sputum cytology. With the help of the computer, we have a list of all the miners who should be watched closely because of age, race, mining history, smoking history, radiation exposure, etc. Examination of the miners is performed at our clinic, where all the records are kept. The sputum is collected there but examined in Grand Junction, Colorado, by Dr. Geno Saccomanno. There are two ways to collect sputum. The best way is to collect three consecutive morning samples. For this, we need the cooperation of the miners. They have to follow these instructions and mail the bottle containing the sample to Grand Junction. "Instructions for obtaining a good cough specimen" The enclosed plastic bottle contains a preservative solution, so do not empty out the liquid in it. When you go to bed, place the plastic bottle at your bedside where it will be handy in the morning. When you first get up in the morning (before breakfast) try to cough up some "phlegm" from deep in your chest, and spit it into the liquid in the bottle. Try coughing several times. If you have difficulty coughing, try inhaling deeply the steam from a teakettle (or home-type inhalator). Keep the amount of saliva (ordinary spit) that you put into the bottle along with the cough specimen as small as possible. Do not collect the "phlegm" or mucous that comes from the back of your nose. Put the cap back on the bottle, and shake it vigorously for two minutes. If the amount of material you have coughed up is quite small, then keep the bottle at your bedside for three or four days, and each morning try to add another cough specimen. After obtaining your cough specimen, repack the bottle in the mailing container, and attach the enclosed mailing label. It does not require any postage stamps. Unfortunately, some miners "forget" to mail the sample and end up with an incomplete physical examination. To avoid this some companies, like Homestake, request that we obtain the sample in our clinic by forcing cough and expectorant with a nebulizer machine. This method does not give as good a sputum sample as the previous one, but we do get a sputum sample for every miner. The policies of different companies, in regard to annual physical examinations are different. All

Jan 1, 1981

By Herman Gill, Dani Delaloye, Madelyn Rubin

The Foothill Tunnel is a remote 16-mile-long untreated drinking water tunnel in the San Francisco Public Utilities Commission’s (SFPUC) Hetch Hetchy Water and Power (HHWP) system. The 14-foot horseshoe shaped tunnel, constructed in the 1920s, is lined intermittently with concrete over approximately 53% of its length, with the balance being unlined rock. After detailed planning, in January of 2020 Mott MacDonald and HHWP staff completed a visual inspection and documented the condition of the tunnel with electronic data collection, photographs, and video with audio recording. The result was a comprehensive condition assessment that identified key areas of the tunnel to monitor.

Jun 13, 2021

By Priscilla P. Nelson, Francis L. C. Fong

Introduction Fracture mechanics is the study of the behavior of cracks and their modes of propagation. During cracking, energy is consumed in creating new surface area. The more energy a material absorbs, the higher is its fracture resistance. This fracture energy is provided either by work done externally, by the release of elastic strain energy within the cracked body, or by a combination of these two effects. Fracture resistance is measured in terms of either the stress intensity factor, K, or the energy release rate (also referred to as crack driving force), G. For linearly elastic materials, these two quantities are related by the following equation: [ ] where [u] is Poisson's ratio and E is the modulus of elasticity. Both K and G are direct functions of the applied force and the crack length. The process of rock cutting with full-face tunnel boring machines (TBMs) involves the indentation of a rock surface by rolling disc tools. Excavation occurs as fractures, extending from the locus of chip indentation, propagate between concentric disc grooves and liberate rock chips from the intact rock face. Since disc cutting is achieved by a fracture process, it is logical to anticipate that differences in cuttability of a variety of rocks should be related to the variation of fracture material properties among the rocks. Such a relation has been demonstrated between the performance of full-face TBMs and the critical crack driving force for excavation in relatively high strength, brittle, low porosity, isotropic rock (Nelson et al., 1985). The objective of this paper is to report on the results of a continued investigation of the relationship between fracture material properties and the effectiveness of disc cutting. Additional reliable data on full-face TBM performance is difficult to obtain, so that the results of disc linear cutter tests performed by the Transport and Road Research Laboratory (TRRL) (U.K.) are utilized in this study. Fracture Material Property Evaluation If a crack tip is subjected to a perfectly plain strain condition, many materials will behave in a brittle manner, and the material resistance to fracture is constant during crack growth. This resistance is referred to as the plain strain fracture toughness, believed to be a material property. The standard testing procedure for this parameter is given in the American Society for Testing and Materials (ASTM) test designation E399. To ensure plain strain conditions, acceptable specimen geometries are specified. Unless these geometric specifications are adhered to, the measured fracture resistance is regarded as the apparent fracture toughness, and a subscript Q is used, as [ ]. The methodology adopted by ASTM E399 is within the framework of Linear Elastic Fracture Mechanics (LEFM). This approach assumes that material resistance against cracking is developed instantaneously, without initial stable or subcritical crack extension. Prior to crack advancement in rock, however, much of the crack driving energy is absorbed in a localized volume in front of the crack tip, referred to as the plasticity or microcracking zone. This capability for energy absorption substantially increases material resistance, and a crack may be arrested unless an increased crack driving force is applied. The LEFM or plain strain assumptions would underestimate the actual fracture resistance of such a material. Such a conservative approximation may be desirable in the design of structures against fatigue or brittle failure. In mining or tunneling, however, an underestimation of crack resistance can lead to the selection of underrated excavation equipment and a decrease in production efficiency. The development of fracture resistance in rock is best described by the material resistance curve, or R-curve, which is a plot of fracture resistance as a function of crack extension. Typically, peak resistance is only reached after a finite amount of subcritical crack growth. The

Jan 1, 1986

By R. Poulin, R. Pakalnis, D. Peterson

Introduction A comprehensive project has been completed at the University of British Columbia that focused on the development of a commercially competitive composite cable bolt. Laboratory evaluation consisted of pull tests, preliminary shear tests, grout column testing and scanning electron microscope evaluation of the composite cable bolt. Field implementation at five underground mines throughout Canada were completed for technical and overall performance evaluation of the new product. The project began in 1989 under the sponsorship of HDRK Ltd., a consortium of mining companies including Inco, Noranda and Falconbridge Ltd. The objective was to develop a cuttable cable bolt that would serve as support for a continuous miner within a hardrock environment (Mah, 1994). The bolt was required to be cuttable by a continuous roadheader without adverse effects to equipment, personnel and the milling process. From the beginning, the focus was to employ existing cable bolt installation technology (Goris et al., 1994) whereby the cable bolts are grouted within a 4.8-cm-diam (1.08-in.diam) or larger employing a portland cement grout having a water: cement ratio between 0.35:1 to 0.4:1. The prototype, developed from Phase I, was technically comparable to that of conventional steel cable bolts. However, high cost and limited accessibility hindered its commercial acceptance. The second phase of the project was sponsored by the British Columbia Science Council and Pacific Pultrusions Ltd. of British Columbia to locally develop a glass fiber cable bolt. This phase of the project has resulted in the DAPPAM cable bolt (Pakalnis et al., 1994). DAPPAM Cable bolts are the second most used support method in Canadian underground mines after mechanical rock bolts. It is projected that 870,000 m (2.9 million ft) of cable bolts are installed annually in Canada (Poulin et al, 1994). The objective of the research program was to develop a glass fiber cable bolt with similar pullout strengths to the conventional steel cable bolts (267 kN - 60,000 lbf). More than 200 laboratory pull tests were conducted employing standard cable bolt test procedures, as outlined by the US Bureau of Mines (Goris, 1994), to assess optimum rod and surface composition, geometry, number required, pullout and shear characteristics, among others. This resulted in the DAPPAM cable bolt (Fig. 1). It consists of 10 individual 0.6cm-diam (0.25-in.-diam) rods enveloping a 2.2-cm (0.8-in.) outside diameter, high-density polyvinyl grout tube. The composite used in the construction of the rods is comprised of about 65% glass fiber within a 35% polyester resin matrix (by volume). Through pultrusion (a continuous fabrication technique), the fibers and resin are combined into a composite material. The strength of the overall composite is largely governed by the material properties, the alignment [ ] of the fibers relative to the applied load and the density and interaction of the overall components within the composite. A further modification to the composite was the addition of a sand grit to the surface of the individual rod. This increased the overall bond strength between the rod and the cement-based grout, used to solidify the cable bolt to the rock mass. The grout tube has an inside diameter of 1.9 cm (0.75 in.) and is rated at a pressure of 1.72 MPa (250 psi). During installation, the grout is pumped through the annulus of the grout tube thereby filling the hole from toe to collar. Laboratory and field trials concluded that a minimum drill hole diameter of 4.8 cm (1.08 in.) be used to ensure optimum grout coverage. Table 1 compares the design strengths (as tested) for DAPPAM vs. the ultimate strengths for a conventional 1.6cm (0.6-in.) steel cable bolt. The characteristics for the steel cable have been derived directly or indirectly by Goris et al. (1994). A design tensile strength of 289 kN (65,000 lbf) was proposed for the composite developed. However, recent tests have indicated maximum breaking strengths of more than 400 kN (90,000 lbf) (Fig. 2). Figure 2 shows the load vs. displacement pull out curves for steel and DAPPAM cable bolts. The methods of testing were standardized so as to be able to compare the results directly. The shear strength of the fiberglass cable is largely a function of the surface area sheared. Shear strengths of 89 kN (20,045 lbf) were obtained for the configuration shown in Fig. 1 when sheared normal to the axis of the cable. The testing procedure was similar to the shear tests performed on steel by Goris (1993). It is important to reinforce the implication that critical bond strength has on the success of an overall support system.

Jan 1, 1995