Search Documents

By Diler Katircioglu-Bayel, Oner Yusuf Toraman, Safak Gokhan Ozkan

One of the most energy-intensive processes for producing submicron range calcite is stirred media mill. In the present work, numerous operating parameters such as solid mass fraction, grinding media size, media filling ratio, and grinding time have been investigated using a vertical type stirred media mill. The results are evaluated on the basis of mean particle size, specific surface area, and specific energy consumption. After conducting this study, optimum experimental conditions found to be as 70% media filling ratio, 25% solid mass fraction, 1 mm grinding media size, and 120 min grinding time. Besides, energy savings up to 22% were achieved with the choice of proper media size.

By C. Özgen Karacan

The formation of the gas emission zone in longwall mining and the potential amount of gas in this zone are factors of local geology and spatial variability within this geology. Therefore, geostatistical methods can be used for modeling and prediction of gas amounts and for assessing its uncertainty in the gas emission zone of longwall mines. This study used core data obtained from 64 exploration boreholes drilled from the surface to the bottom of the Pittsburgh coal seam in a mining district in the Northern Appalachian basin. After identifying important coal layers for the gas emission zone, semivariogram modeling was conducted for different coal seams to define the distribution and continuity of various attributes. Sequential simulations were performed for stochastic assessment of these attributes to calculate gas-in-place (GIP) in each coal seam. GIP calculations for coals of various gas emissions zones were combined and ranked for their cumulative distribution function to find GIP in the caved zone and in the fractured zone at the 5%, 50%, and 95% quantiles. Fifty percent quantile results were later used to isolate a panel from the whole area and create a mosaic representation corresponding to the daily advance rate of the longwall face. This approach helped to estimate the daily emissions of this panel from the caved zone and from the fractured zone. Results showed that gas-in-place in the Pittsburgh coal seam, in the caved zone, and in the fractured zone showed spatial correlations that could be modeled and estimated using geostatistical methods. This study showed that gas-in- place volumes in the study area may be as high as 12.3 Bscf and as much as 3.5 MMscf per acre of mining.

Jan 1, 2012

By D. Kozelj

Introduction The porphyry copper deposit “Borska Reka” is the biggest undeveloped deposit in the Timok Magmatic Complex (TMC). Total reserve calculated manually is 611 Mt (cut-off grade 0.3% Cu) of 0.62% Cu, 0.21 g/t Au and 1.81 g/t Ag and 869 Mt of 0.58% Cu, 0.14 g/t Au and 1.11 g/t Ag using software. But since several deep drill holes are suspended in high grade (0.7% Cu) porphyry, total reserves could exceed 1Gt. The massive sulfide is also detected in the central (12 m at 4% Cu) and the bottom of porphyry style. Deposit was discovered during geologic exploration of deeper part of the Bor copper and gold deposit, i.e. area of high sulfidation with dominant massive sulfides. During exploitation of massive sulfide, constant explorations were carried out aimed at the expansion of reserve and discovery of new ore bodies. In that way, porphyry copper mineralization was discovered without knowing in the beginning that it was different mineralization type in regard to the ones that had been already identified and exploited. Vertical extension of porphyry is 0 m up to -1000 m sea level and not contoured along plunge. In the very beginning (1976), the exploration was focused on the shallow part of porphyry. That is because block caving method of massive underground mining was not developed at that time. Up to 1999, most of activity was related to underground exploration up to level -395 m. Geographic position The Bor deposit is located close to the industrial and University town Bor, which has over 50,000 inhabitants (census made in the year 2002). Apart from the Bor Mines, industrial complex of Mining & Smelting Basin Bor (RTB) comprises also a copper smelter (installed capacity up to 160,000 tons of blister copper) and tank house, copper wire factory, copper tube factory etc. Currently, RTB Bor is under privatization process that is going to be completed by the end of 2006. Up to date, over 20 companies have bought tender documentation.

Jan 1, 2007

By M. Ge

Signal processing is a major challenge for In-Seam Seismic (ISS) technique. Fourier Transform is an important tool for signal processing such as frequency analysis. However, for ISS signal, localized information, especially time-frequency localization is even more important. Wavelet Transform (WT) provides another approach to study the signal as a function of frequency and time. The objective of this paper is to demonstrate the application and advantages of WT to seismic signal analysis. Both transmission and reflection signals from coal mine void detection experiments are analyzed. The results illustrate that WT appears to be a powerful and convenient method for the in-seam seismic signal processing.

Jan 1, 2007

By M. Kuchta, A. Newman

LKAB’s Kiruna Mine, located in northern Sweden, produces about 24 Mton of iron ore yearly using sublevel caving. For efficiency, the mine must deliver planned quantities of three ore products. We use mixed integer programming to schedule Kiruna’s operations, specifically, which production blocks should be mined, and when they should be mined to minimize deviations from planned production quantities while adhering to mining restrictions (e.g., sequencing). A new production block database and a well-formulated mixed integer programming model dramatically reduce the size of the original problem; in less than ten minutes we generate five-year schedules with time fidelity of months.

Jan 1, 2002

By J. F. T. Agapito, R. R. Goodrich

Yield pillars have been used for many years to help reduce stresses near mine openings and improve roof and floor stability. A yield pillar is often defined as a pillar that fails but retains residual strength. Stress transfer occurs through the roof and floor after the peak strength of the pillar is reached. High stresses are transferred from around the openings onto abutments that can be barrier pillars or unmined ground. This mechanism, often referred to as pressure arching, is possible as long as the width of yield pillars is less than the critical width above which stresses cannot be carried by the overburden. Significant stress transfer also can occur due to small amounts of pillar and/or floor yielding before the peak strength is reached. This is accomplished in a quasi-elastic manner with little or no visible roof and pillar fracturing or floor heave. Long-term stability may be achieved when stresses and mechanical properties are favorable to pre-failure yielding. This paper gives practical examples where improvements in stability and resource recovery were achieved with this mechanism. Yielding was assessed by comparing measured and calculated vertical pillar stresses. Results indicated that calculated stresses in the pillars were 25 to 40 percent higher than the measured stresses, demonstrating significant arching load transfer to the abutments. Pre-failure yielding is probably often present but unintentional in both development and production areas. Better recognition and use of this mechanism should lead to improved designs as mines become deeper.

Jan 1, 2001

By Allison

During the 1980’s, laboratories opened throughout the United States to serve the analysis needs of a rapidly growing asbestos abatement industry. The samples analyzed were either collected during the abatement of known asbestos-containing materials or were suspect asbestos-containing construction materials. Many asbestos analysts received minimal training and used analytical protocols that were industry specific. False positives (reporting a sample as containing asbestos when none is present) went unnoticed or had minor repercussions. The mindset of the industry was to err on the conservative side – it would be better to identify a non-asbestos fiber as asbestos than visa versa. With growing public awareness of the health hazards of asbestos, other materials began to be tested for asbestos content. Rock and ores began to be tested for naturally occurring asbestos by these laboratories using the same protocols or an in-house protocol. Analysts were given no additional training and accreditation, in most cases, it was not required. With no consistency in sample collection, testing protocol or expertise in analysis, significant discrepancies in final results can be expected. If we further complicate this scenario with misidentification of naturally occurring look-a-likes for asbestos, expensive false positives are likely. To avoid the repercussions of misidentification of naturally occurring chrysotile asbestos from look-a-like fibers in rock and ores, correct sampling and analysis protocols with more stringent scientific diagnostic criteria are needed.

Jan 1, 2005

Multilevel-multiseam hardcoal mines on the European continent usually consist of a huge network of underground openings, sometimes more than 200 km long in total, with some longwalls operating down to a depth of 1,500 m. While operating several longwalls simultaneously, these mines are making use of a number of stationary and mobile measurement- and analysis units in their main ventilation passes combined with atmospheric measurements on the surface. This paper provides an overview over the systems and technology used and describes the typical set-up of a measuring net. To detect and monitor underground fires through fire gases measurement and -analysis, a mobile underground testing laboratory collects data locally in the area of the fire. These laboratories have proven to be extremely useful not only during the actual fire fighting but also for the long-term gas measurements in critical mine areas. They have repeatedly detected starting fires and have thus given the mine the opportunity to react early and to avoid larger damage. Therefore several mobile laboratory units have now been installed for long-term testing in a number of German mines and similar units are being used in the Czech Republic and Poland.

Jan 1, 2012

By S. Bargigli, S. Ulgiati, M. Raugei, F. Cherubini

Metallic magnesium is mostly used in lightweight alloys in order to decrease fuel consumption in automotive applications. Several different production processes are currently used worldwide, and the magnesium production scenario is changing rapidly, with Chinese production increasingly dominating the world market. For the purpose of this paper, a novel approach to Life Cycle Assessment was applied, in which Material Flow Accounting and energy-based methods (Embodied Energy, Exergy and Emergy Analyses) are integrated and complemented, with a detailed description of the environmental hazards associated with emissions from all the different processes.

Jan 1, 2005

By Mohamed Yusuff

Modern transportation systems are one of the most important achievements of our civilization and provide us with tools for broadening individual and social freedom of choice. The transportation system initiated today is handed dawn to the next generation, probably with little choice because of the enormous expenditure of monies involved, and influence their way of life as to where they should live and where they should work. The ever increasing antagonism between the citizens and the planners of the transportation systems necessitates a careful review of the entire planning process. The planning process can be broadly classified into: the goal formulation and decision making process; the plan development process; and the plan implementation process. THE GOAL FORMULATION AND DECISION MAKING PROCESS Goal formulation and decision making is one of the vital phases of the planning process and is primarily based upon social values. In measuring social values, the planner must employ an appropriate scale of measurement since in the absence of this yardstick, these values tend to became vague and abstract ideals. The need for major social programs and concerns (poverty, etc.) of the urban areas should be analyzed to determine the type of transportation system which would contribute to the solution.

Jan 1, 1974

By H. Verakis, M. J. Sapko

The Pittsburgh Research Laboratory (PRL)1 of the National Institute for Occupational Safety and Health (NIOSH) in collaboration with the Mine Safety and Health Administration (MSHA) Technical Support Center has devised a prototype hand-held instrument which can provide a direct assessment of the potential explosibility of a coal and rock dust mixture. Current Federal regulations require that rock dust be applied in all underground areas of a coal mine to mitigate the propagation of a coal dust explosion. To determine compliance with the Federal regulation, mine inspectors collect dust samples from sections of underground coal mines for an MSHA laboratory analysis of incombustible content. However, the laboratory analysis may not be completed for more than a week or two, during which time the mine area from which samples are taken may be inadequately protected. The operation of the Coal Dust Explosibility Meter (CDEM) is based on the difference in optical reflectance between light rock dust and dark coal dust. For a given coal volatility, the optical reflectance of such mixtures is relatively constant at the limit of explosibility, independent of the coal dust particle size. The CDEM is not intended to replace the current MSHA laboratory analysis of coal mine dust samples for incombustible content, but to serve as a supplemental device for enhancing mine safety through improved rock dusting practices.

Jan 1, 2006

By Gerald C. Smith

Introduction Newmont Mining Corp.'s Carlin Gold Mining Co. mines gold ore and waste material from four open-pit mines in Northeastern Nevada. Combined production rate is 24.5 Mt/a (27 million stpy). The company is producing gold bullion from the 2.4 kt/d (2600 stpd) Carlin Mill No. 1. and the 2.3 kt/d (2600 stpd) Maggie Creek heap leaching plant. In August 1985, the 6.3 kt/d (7000 stpd) Carlin Mill No. 2 at Gold Quarry came on-line. The total combined throughput of 11.2 kt/d (12,000 stpd) will make Carlin Gold Mining one of the largest US gold producers. Feasibility studies are underway to increase the total gold out-put from Gold Quarry. This will be done by adding a continuous dump-leaching process that will recover gold from lower grade ore. History In 1961, Newmont exploration geologists located claims in the Lynn Creek mining district near Carlin, NV. An exploration drilling program revealed significant gold mineralization. A stepped-up drilling program revealed an ore body with an estimated 10 Mt (11 million st) of ore containing 109 t (3.5 million oz) of gold. Test results in 1963 allowed metallurgists to develop the flowsheet and design for a 1.8-kt/d (2000-stpd) countercurrent decantation (CCD) cyanide plant. Carlin Gold Mining Co. was formed to operate the property. Carlin purchased its first mining equipment in 1965. This consisted of two Bucyrus-Erie 2.7 m3 (3.5 cu yd) shovels and nine 27.2 t (30 st) Wabco Haulpak trucks, two Inger¬soll-Rand track-mounted drills, one Chicago Pneumatic T-650 rotary drill, one rubber tired Michigan 280 dozer, one Caterpillar D-8 36A track dozer, one Caterpillar 16 motor grader, and the necessary ancillary equipment. The fleet was capable of mining 3.2 Mt/a (3.5 mil¬lion stpy) working two eight-hour shifts, five days a week. In 1967, one P&H 1500 3.8 m3(5 cu yd) diesel electrical shovel and three 59 t (65 st) Dart trucks were added to the fleet, along with a Chicago Pneumatic rubber tire mounted rotary drill. This equipment addition increased the mining capabilities to 5.7 Mt/a (6.3 million stpy). Three separate pits, the Main, East, and West, within a 1.6-km (1-mile) radius of the Carlin mill were being mined. The crew consisted of 46 hourly men and three supervisors. This equals 497 t/ total hourly manshift (548 st) or 407 t/total manshift (515 st). Rising gold prices in the early 1970s allowed lower grade deposits to be mined at greater distances from the mill. The Boot-strap pit, 19.3 km (12 miles) north of Carlin, was started in 1973. Two Hough 45.4 t (50 st) front-end loaders, four Wabco Haulpak 45.4 t (50 st) trucks, and a second track type D-8H dozer were added. The higher grade ore was trucked to the Carlin mill using three

Jan 11, 1985

By W. Scheetz

The Brewer Gold Mine is an open-pit, heap leach operation that processes about 122 kt/m (135,000 stpm). The mine is operated by Brewer Gold Inc., a subsidiary of Westmont Mining Inc., and is located near Jefferson, SC, about 80 km (50 miles) southeast of Charlotte, NC and 80 km (50 miles) northeast of Columbia, SC (Fig. 1). All of the ore to date has been produced from a breccia body of hydrothermal origin and a related smaller body of fault-controlled ore, known as the B-6. Reserves at the time the mine commenced production were 4.6 Mt (5.1 million st) grading 1.4 g/t (0.042 oz per st) gold. History Although some reports of a pre-Revolution War shaft at the Brewer are in the literature (Lieber, 1856, Nitze and Wilkens, 1897), gold was first produced in earnest from the Brewer Mine in 1828. Production occurred primarily from placer deposits south of the present mine workings. Lieber noted in 1856 that “every branch, gulch, ravine or even declivity of the main hill has been washed and rewashed.”

Jan 1, 1991

A large-diameter road tunnel will cross beneath the strait in Istanbul and expand the infrastructure bottleneck between Europe and Asia. The technical planning of the tunneling operations poses complex challenges. Therefore, the construction consortium ordered a specially adapted tunnel boring machine (TBM) from Herrenknecht. The 13.6-m (44.6-ft) machine, a Mixshield, was completed in early July 2013 in Schwanau, Germany. To get from the European to the Asian side of Istanbul, people and goods have to cross the Bosporus Straits. So far, two road bridges as well as ferries provide the only transport link between the two parts of the city and the two continents. The tense traffic situation for the nearly 14 million residents of the city and for international transit traffic should be improved considerably thanks to the construction of a new road tunnel under the Bosporus. ?The project is certainly one of the most challenging tunneling operations currently being addressed in the world,? said Herrenknecht project manager Georg Schleer. The route of the ?Istanbul Strait Road Tube Crossing Project? runs around 100 m (330 ft) below sea level at its deepest point. The interior diameter of the tunnel will be 12 m (40 ft) so that two lanes in each direction can be accommodated. They will extend one above the other on two levels. 3.34 km (2.1 miles) of the tunnel with a total length of 5.4 km (3.3 miles) are being created by a 13.6-m- (44.6-ft-) diameter Herrenknecht TBM that will begin its underground mission from a launch shaft on the Asian side.

Sep 1, 2013

By Maurício Covcevich Bagatini, Maycon Athayde

Nowadays, the HPGR (high-pressure grinding rolls) is an intermediate step between filtering and balling in the most modern iron ore pelletizing operation. The operation debottlenecks filtering process and reduces pressure over the typical milling process to control particle size to the balling. The present study evaluated aspects of microwave application to the iron ore concentrate fed to HPGR in a bench scale unit. Iron ore concentrate was irradiated varying the microwave exposure time and grinding efficiency was evaluated. The moisture influence in the HPGR efficiency was also assessed. The pellet feed blaine surface area (BSA) improved by 300 cm2/g and % < 325# fraction by 3%. Scanning electron microscope (SEM) images show the formation of micro-cracks onto the particle surface induced by microwave; the effect observed helped improve the milling process performance, in addition to the moisture reduction observed due to the temperature increase.

By Steve Kral

Commodity price down cycles are a fact of life in the mining industry. And companies pre-pare for them as best they can. Evenso, operations are still curtailed or closed during those cycles, profits shrink, layoffs are inevitable and many companies do not survive. However, one of the few good things that occurs during down cycles is the new, innovative exploration, mining and processing technologies that come about during hard times. To survive the lean times, the mining industry turns to improved technology to decrease costs and hold the bottom line. And, because mining is a cyclical business, each down cycle brings about technology improvements that carry over into the good times.

Jan 1, 2004

By G. L. Dollinger, J. P. Kindsvater, J. A. Gibson

DESIGN AND DEVELOPMENT OF A MOBILE MINING MACHINE INTRODUCTION Until recently, developing tunnels in hard rock has been accomplished either by the drill and blast method or by using large tunnel boring machines. Combining the flexibility of drill and blast with the safety, efficiency and productivity of a TBM has been the objective of mining machinery producers for many years. In 1979 The Robbins Company began developing a new type of tunnel boring machine called the Mobile Miner to meet these objectives. The development and testing of the Mobile Miner is the subject of this paper. CURRENT MINE DEVELOPMENT METHODS Both the drill and blast method and the use of a TBM have notable advantages and disadvantages. The drill and blast method, for example, allows much more flexibility, requires less setup time and has a lower initial cost than a TBM; however it requires the use of high explosives and blasting has a disrupting effect on the rock surrounding the development. A TBM, on the other hand, is safer to operate, more efficient, more productive and produces smooth tunnel walls without disturbing the surrounding rock. In longer straight drifts it will easily out distance the drill and blast method. The TBM, however, is limited to boring a circular cross section tunnel which must then be modified if a flat floor is required. It also has a higher initial cost and an extended setup period.

Jan 1, 1985

The 21st Annual American Mining Hall of Fame Awards Banquet sponsored by the Mining Foundation of the Southwest will be held at the Sheraton Tucson Hotel in Tucson, AZ on Saturday, Dec. 6, 2003. This year’s inductee, guest of honor and featured speaker at the banquet will be Thomas J. O’Neil, recently retired president and chief operating officer of Cleveland Cliffs Mining. Prior to Cliffs, O’Neil spent 10 years with Cyprus Minerals. He was also professor and head of the Department of Mining and Geological Engineering at the University of Arizona. As representatives of mining heritage, the Hall of Fame will induct James Boyd and Thomas F. Walsh. Walsh discovered a rich gold telluride vein in Ouray, CO, which became the Camp Bird gold mine. Boyd was a former director of the U.S. Bureau of Mines, vice president of Kennecott Copper and later president of Copper Range.

Jan 1, 2003

By J. E. Friant

Until 1956, drill and blast was the only way to excavate rock. In that year, a tunneling machine using disc type cutters economically bored a small Toronto tunnel. Its amazing 105 ft/day set a new world record and set the stage for a new industry. The Disc Cutter Role in Excavation Mechanical excavation of hard rock is by now deeply ensconced in the heavy civil construction industry. All over the world, from the Swiss Alp Melange to Hong Kong Granite, to New York Gneiss, huge Tunneling Boring Machines (TBMs) create transportation, water and sewer tunnels. Powerful machines, boasting as much as 6000 hp, bore through rock, excavating in excess of 1400 tons per hour. The tool that makes this tunneling phenomenon possible is the single blade, rolling disc cutter. These hardened steel discs, from 15 1/2 to 19 inches diameter are arranged on a rotating cutterhead, to cut concentric circles in the rock. As the machine is propelled forward under great pressure, rock below each cutter is crushed. But the efficiency of the cutterhead is derived from the science of cutter spacing (distance between cutter paths). The majority of the rock excavated is not crushed, but flakes off in chips and chunks. No pick, tooth, or drag type cutting tool can duplicate the performance of a disc cutter. The economic use of drag type tools is limited to as low as 5,000 psi UCS rock strength in massive formations. In weakly bonded, foliated rock, drag tools do better, but are still limited to rock generally less than 15,000 psi.

Jan 1, 2002

By A. W. Khair

This paper deals with the design characteristics of cutting tools and the operating parameters these tools are usually subjected to. Eight types of cutting tools/bits with different geometrical shapes and sizes were tested in a linear cutting apparatus, utilizing concrete blocks. The objectives of these experiments were to study the performance of each type of bit, make qualitative assessment of each bit geometry and size and establish cutting parameters for efficient utilization of the tools. During the experiment required forces Fx, Fy, and Fz, cutting, penetrating and lateral forces respectively and audible and sub-audible noises were measured. In these experiments, the depth of cut was kept constant to 1.5 inch while the bit spacing was varied 1.5,2.25 and 3.0 inch (3.75,5.6 and 7.5cm respectively). The results of these experiments indicated that by optimum ratio of depth of cut to bit spacing, the cutting face will be cleaned with the least ridge/land remains between the bit groves, resulting in least specific energy consumption, more large and less fine product particles and substantial reduction of audible noise. The results of these experiments also showed that proper bit design not only decreased cutting energy consumption but also reduced audible noise.

Jan 1, 2001