Search Documents

By A. I. Kalugin, A. A. Abramov, D. E. Kozlov, D. V. Magazanik

Based on theoretical and experimental researches of phosphate and carbonate minerals flotation in the presence of soluable glass at various pH values and sodium silicate concentrations, it has been established that the presence of soluble glass in solution leads to formation of silicate compounds on the surface of phosphate and carbonate minerals causing change in their floatability for the worse. The harmful influence of soluable salts is done by tying of collector as metallic soaps, forming precipitates on the surface of minerals to be floated and causing their depression of flotation, and breaching of the froth etc. Depressing action of slimes and products of interaction with collector depends on the ratio of values and signs of potentials of the mineral surfaces. The possibility of phosphate and gangue minerals separation can be evaluated by comparing the minimum-necessary concentrations of collector required for their flotation.

Jan 1, 2002

By J. G. Asbury

Broadly conceived, the demand for electricity depends upon three sets of variables: (i) the growths of the many individual demands for energy services; (ii) the competitiveness of electrically driven technologies in meeting these demands; and (iii) the energy-conversion efficiencies of installed electrical technologies. The first set of variables establishes the size of the potential market; the second, the market penetration of electrical equipment; and the third, the quantity of electricity required to operate the equipment. All forecasts of electricity consumption ultimately depend upon inferred or assumed relationships to describe the future behavior of these variables. This partitioning of the demand-forecasting problem is conceptually useful and will guide the discussion presented in this paper. However, it is also something of an oversimplification. Examined in more detail, the electricity fore-casting problem is exceedingly complex. The variables mentioned above are, in turn, found to depend upon more fundamental sets of demographic technological, resource, and policy variables. The demand projections developed by the major forecasting services are usually developed in terms of these underlying variables, which themselves must be independently forecast.

Jan 1, 1985

By Zhang Youdi

A two-step approach has been developed for surface mine short term planning by the authors. The first step is mid term control and planning by the use of Goal Programming. This step gives optimal results for mid term planning (i. e. yearly or quarterly mine plan) as well as a macro control for short term planning (i. e. monthly or weekly plan.) The second step of the approach deals with short term production scheduling by the application of CAD technique and Systems Simulation. An interactive color character graphic design system has been developed with a software package. The menu-driven and module- structured package provides sufficient functions for surface mine short term planning and makes the model very flexible and user-friendly. This model has been applied to a large surface coal mine for short term planning optimization. Satisfactory results have been obtained. It is concluded that for complicated mining conditions this two-step combined approach gives an optimal control of mid term planning, makes the short term planning easier to avoid blindness; it has been proven that the Goal Programming is a powerful tool for solving multi-objective decision-making problems; guided by GP mid term planning, the CAD technique and simulation software package for short term planning are able to be concentrated on their practicality and flexibility.

Jan 1, 1992

By David E. Peterson, F. Merz

The Waihi Gold Mining Company Limited, Martha Hill Project was the first major hard rock mining operation following the resurgence of the mining industry in New Zealand. Because of its location adjoining a town and at the southern part of the sensitive Coromandel Peninsula, the operation received a high level of public scrutiny. Very srrict limits for effluent criteria had to be met and led to the necessity for advanced wastewater rreatment technology. The process technology selected was the copper catalysed oxidation of cyanide using hydrogen peroxide, with subsequent removal of heavy metals by precipitation and filrration. This paper discusses the adoption of environment limits together with the detailed description of the plant and design criteria. Data of the one year's operational history is also presented.

Jan 1, 1991

By Robert J. Ramsey, N. Finkelstein, Robert D. Jeppson

Introduction The Utah Copper Division of Kennecott Copper Corporation will present its contribution to the A. M. Gaudin Flotation Symposium in four parts. The first two segments will discuss briefly the historical development of the Utah Copper Division and describe the ore body. The third segment will review the facilities and operating procedures for the Utah Copper Division's newest plant, the Bonneville Concentrator. The fourth segment describes flotation process circuitry, including molybdenite recovery procedures, at the Arthur and Magna concentrators. (The Bonneville concentrator is a crushing and grinding unit and does not have its own flotation plant). 1. Historical Development Progress through change has been the key to the successful operation of the Utah Copper Division for more than 70 years. As the original low-grade copper operation, the pressures to remain competitive and profitable have dictated the timing and extent of each change. Much of the change has occurred through technological and economic advancements in the area of ore concentration. The Utah Copper Division of Kennecott Copper Corporation had its origin June 4, 1903, when the Utah Copper Company was organized. The initial mill of 300 tpd (tons per day) capacity was built at Copperton a few miles below the present Bingham Canyon mine site. From 1904 to 1910, the Copperton mill was expanded to a capacity of 1,000 tpd, and all of the known apparatus for gravity concentration were evaluated.

Jan 1, 1976

By Bern Klein, Richard W. Lawrence, Scott Frostad

Laboratory and field scale kinetic testing was conducted to evaluate scaling up of laboratory data. Two 20- tonne (field) cells were monitored for internal temperature, pH, conductivity, volume and rate of flow, and water quality. On a surface are. basis, results showed sulfide oxidation rates obtained using 50-kg cells are more sensitive to changes in aeration than those from 1-kg cells. Correcting the laboratory oxidation rates for field temperatures with a pH 7 activation energy, which is in the field drainage pH range, returned oxidation rates an order of magnitude lower than the field cell rates.

Jan 1, 2000

By Satya Harpalani

An investigation was carried out to study the microscopic structure of coal in order to understand the phenomenon of methane migration. A Scanning Electron Microscope (SEH) was used to study the surface and pore structure of bituminous coal taken from an underground mine. Micrographs obtained showed the highly porous nature of coal which explains the large quantities of gases that remain within the pores in the compressed and adsorbed forms. These micrographs further showed that most of the pores within the coal matrix are the 'dead-end' type and do not contribute much towards the flow of gas. The most important finding was that solid coal has a network of cracks and fractures indicating that it is these cracks that are primarily responsible for the gas flow, rather than the pores. The size and distribution of the pores within coal influence the capacity of coal to retain methane but movement of the gas molecules is the responsibility of the microfractures. Any mathematical modeling to simulate gas flow through coal must take this into account. For purposes of modeling, the structure of coal can be considered to have dual porosity. First, the gas molecules are released from the pores and there is a gradual migration towards the fractures. Once the gas reaches the fractures, its movement is eased greatly along these fractures.

Jan 1, 1987

By Bruce C. Trent

The need for effectively evaluating the potential for surface subsidence due to under- ground mining has been widely documented. As the emphasis within the coal mining industry changes to reflect the increasing demand of this resource, the potential for damage due to differential surface subsidence will certainly become more acute. The present state-of-the-art of predicting ground motion due to underground excavations is, at best, primitive when one considers the immense complexity of possible geological inter- actions. For the most part predictions have been limited to empirical evaluations based upon earlier case histories. While the tools of the subsidence engineer are limited, they are important and serve to provide reasonable bounds for possible ground motion. As underground mining becomes more extensive, however, there will be many instances where excessive subsidence will be most undesirable and yet there may be few, if any, case histories similar to the operation in question.

Jan 1, 1982

By Philip M. Rice, Paul Schmall, Peter W. Deming, Hugh S. Lacy

A groundwater cut-off is needed to provide a stable face of tunnels to be constructed by jacking precast rectangular tunnel segments beneath commuter rail tracks for the new I-90 extension in Boston, MA. Extensive obstructions are present within the path of the tunnels. This paper describes how the use of artificially frozen ground is being planned to provide a reliable groundwater cutoff and assure a stable tunnel face. Monitoring during freezing assures continuity of the cutoff. Laboratory testing of frozen soil samples aided the design of this frozen soil boundary. Logistics of installing vertical freeze pipes are described.

Jan 1, 1999

By Karl P. Norrena, Clayton V. Deutsch

Ore and waste cannot always be visually separated. The distinction between ore and waste may need to be made on the basis of blasthole sampling. Hand drawn dig limits or computer-generated contour lines do not account for uncertainty, economics or equipment. Geometric methods for interpreting grade information such as the polygonal or triangulation methods share the same limitations as contouring. Geostatistical techniques exist for the realistic modeling of grade variations and uncertainty. Decision analysis techniques exist for the binary classification of ore, and waste blocks in the presence of this uncertainty. Block-by-block classification is not enough; mining equipment cannot exercise free selection of blocks. There is a need for procedures to determine optimal dig limits that account for (1) the uncertainty in the grades, (2) the economics of risk-qualified decision-making, and (3) the ability of the mining equipment to dig to specific limits. This paper presents a procedure for optimal determination of dig limits that account for these constraints. Simulated annealing (SA) is used with modest computational requirements because the number of variables is relatively small. The solution of the optimization problem is dig limits that maximize profit under multiple constraints. The method is illustrated with different constraints and tested against hand drawn dig limits in a "Dig Limit Challenge," which illustrates the efficacy of the new method.

Jan 1, 2002

By Hans Smit

The face of mining as we know it is set to change in the very near future as mining companies all over the globe realize the implications of accessing the vast mineral wealth contained on, and under, our ocean floors. With some land based mineral deposits being fully exploited across the world, deep sea mining is set to revolutionize global approaches to the search for precious metals and other sought after minerals. [ ] Previously, the financial implications of deep sea mining outweighed the benefits of access to the mineral rich deposits identified all around the world. The process of marine diamond mining off the west coast of southern Africa started in the late 1950?s by a Texan, Sammy Collins, and subsequently continued by De Beers to the present day, has proven to be an excellent proving ground for the development of technology and mining systems that ensure a sustainable and financially viable business. [ ]

Jan 1, 2008

By Mritunjoy Sengupta

The Green River formations in the Western U.S.A. contains vast amounts of petroleum reserves in oil shale deposits. Exploitation of this petroleum reserve calls for large scale mining of the oil shale. Applicable mining methods include conventional underground mining using roan and pillar, sub-level caving and block caving; underground insitu retorting of oil shale and open pit mining. Roam and pillar mining offers one of the most economic methods of underground mining of oil shale. A 2.4 x l09 litre per year (50,000 barrels per day) of crude oil production would require a daily oil shale production of 100,000 tomes per day from underground operations. For this large production, a highly mechanized room and pillar mining muld utilize large capacity diesel equipment such as 85 tonne trucks and 8m front end loaders. The total air requirements of an oil shale mining operations can. be as high as 28443/s. Ventilation planning for such a large scale underground mining operation presents a formidable task. The major objectives of providing ventilation air to underground workings are to dilute airborne .dust and diesel fumes to harmless levels, and to insure that the mine environment is compatible with the health and safety of mine personnel. Regulation of air velocities and air temperatures is a major factor in mine environmental control. Colorado State law requires that a minimum of 0.047m3/s of fresh air be supplied for each kW of diesel power operating underground. Additionally, 0.047m3/s of fresh air must be supplied for each underground employee, and a minimum air velocity of 0.15m/s must be maintained in all working places. It is desirable to exceed this minimum velocity in order to prevent stratification of ventilation air. Moreover, Colorado law also stipulates the maximum allowable concentration of noxious gases mine air, below: ? C02 - 0.5% by volume, 5,000 ppm. ? CO - 0.005% by volume, 50 ppm. ? Oxides of Nitrogen - 0.0025% by volume, 25ppm. ? Nitrogen Dioxide 0.005% by volume, 5 ppm. This paper examines ventilation requirements for the underground mine, with respect to air quality requirements and distribution of air in mine workings in light of the above regulations. Analyses were made for sane typical mining plans to determine airflow resistance or pressure drops and fan horsepower requirements. In addition, the possible occurrence of high concentrations of toxic gases, was examined. Expected temperature levels in mine workings were approximated.

Jan 1, 1980

By G. Atesok, M. S. Celik, G. Onal, I. Yildirim

A new coarse cleaning device, the Stripa, has been developed for processing of coal in the size range of -100+10 mm. The Stripa is an auotogenous heavy medium separator originally developed for processing of iron ores. Although it has been employed in concentrating ores such as chromite, it has not been applied in coal cleaning. In this study, a pilot plant scale modified Stripa and its counterpart alternative, a diaphragm jig, are compared using subbituminous and lignitic coals. The separation performance of the Stripa and the diaphragm jig has been established in the light of washability properties of the coal samples. Comparison of the performance of the Stripa with that of the jig indicates that the Stripa can be used in coal preparation circuits as an alternative to jigs in the size range of -100+10 mm. Simplicity, low initial investment, and low operating and maintenance costs make the Stripa a plausible candidate for coarse coal cleaning. More importantly, Stripa due to its short residence time, has a superior capacity over jig.

Jan 1, 1995

By James Warren Andrews, Philip C. Nyberg

The regulation of exposure of underground personnel to radon and its daughter products has significantly changed since the 1950's. The U.S. Bureau of Mines - Mining Enforcement and Safety Administration (MESA) - Mine Safety and Health Administration (MSHA) sequence of standards and regulations have lowered the maximum allowable occupational exposure and now the new Environmental Protection Agency (EPA) National Emission Standards for Hazardous Air Pollutants, effective in 1990, have further regulated uranium mine emissions. Under the authority of Section 112 of the Clean Air Act (42 U.S.C. 7401), the EPA has set regulations for the control of radon (Rn-222) emissions from underground uranium mines as well as other sources. Since the venting of radon from the mine atmosphere to the outside air is a major component of the miner's protection, and since this is the first quantitative effort to limit gaseous mine emissions to the environment, it was felt that it would be useful to examine the implementation of the EPA regulation at working mines. The concern was not only for determining compliance with the regulation but also for observing what effect the rule might have on mine air quality and thus on worker exposure. The regulation is stated in terms of the maximum permitted radiation dose to the closest potentially exposed individual, which is calculated from a computer program supplied by EPA and radon emission rates measured by the mine operator. Relative proximity to nearby populations determines the allowable magnitude of mine exhaust ventilation emissions. For some mines this is a serious operational constraint.

Jan 1, 1991

By B. M. Flohr

Railroads are cost competitive with trucks for hauls greater than 500 miles - WRONG. Today I will tell you about many rail movements of less than 100 miles throughout the country. Rail is a short haul transportation alternative you must consider. Transportation today is the largest controllable cost in the total cost of production of goods. In fact it is the one cost area where aggressive management, using new tools, can achieve significant reductions. You can't control the price of metals in the world market, you can't control labor rates since they are tied to industry norms, and the price of raw materials are relatively insensitive to specific price reductions to your firm. Transportation is the one area where major savings are now being realized. Sample Movements First, I will give you several examples of short haul rail moves to make you a believer that they do exist. Then I will show you the reasons why railroads suddenly "like" short hauls.

Jan 1, 1986

By A. J. Jeffery

Heat transfer to a fluid flowing through a rough duct has been shown by many researchers to be a function of surface roughness. The effect of roughness asperities on the duct surface is to turbulate the fluid as it flows through the duct, increasing frictional pressure losses and convective heat transfer rates, and also increasing the surface area per unit length available for heat transfer. These factors combine to increase the total costs to the mine in terms of refrigeration and fan power requirements. A measurement system designed to automate the collection of tunnel roughness information and based on an infra-red timed pulse laser has been developed at the Royal School of Mines in London. The system allows accurate, high resolution digital recordings of tunnel surfaces to be made in two or three dimensions. Software for analysing the data has been written, and the description of a complex surface via single numerical term has been explored. A relationship between the numerically measured surface roughness and the pressure loss of the ventilating air is being investigated with a view to establishing an alternative method of describing tunnel roughness. The paper describes the roughness measuring technique developed and the analytical techniques explored so far.

Jan 1, 1993

By M. K. Gangal, E. D. Dainty, G. Kunchur

This paper presents a validation of C02 as a single surrogate measurement for other diesel-emitted pollutants in multi-diesel-machine operations typical of small underground mines. This means that the simple measurement of C02 alone can be used to estimate the concentrations of other components of diesel exhaust in the mine environment. The linear relationship of C02 concentration with other diesel-emitted pollutants was indicated by the results of simultaneous real-time monitoring of C02 with CO, NO, NO2, SO2, Respirable Combustible Dust (RCD), and Air Quality Index (AQI) in several small underground mines. The SO2 was not directly measured but calculated from the measured C02 concentration and diesel fuel analysis for carbon, hydrogen and sulphur. The measurements were made in the return air drift under various mining conditions involving a number of diesel LHDs and haulage trucks. The statistical analysis and mathematical representation of the several components of diesel pollutants with C02 are presented. Regression analysis shows that at the 1 percent level of significance there is a strong linear relationship of these diesel pollutants with C02. This relationship is discussed in detail, concluding that C02 measurement alone is a good indicator of overall mine air quality and can be used as a control parameter.

Jan 1, 1991

By E. A. Rychkun

Mining and environmental objectives have traditionally been in conflict. This conflict reflects a delicate balance between the need to spend money to protect the environment, and the need to save money by extracting minerals efficiently. In an increasing number of cases, profit margins diminish rapidly with new environmental regulations and reactionary measures. Forced cleanups and increasing restrictions are unwelcome expensive processes. A practical solution lies in planning rather than reacting. This requires the ability to precisely quantify and qualify environmentally sensitive problems by providing effective engineering tools to model, visualize and analyze subsurface conditions. Prevention of environmental conflicts, and effective cost control are both rooted in the mining company's ability to construct accurate models, monitor changes, assess contamination risks and to design effective remediation plan. This paper presents a case study where these issues are addresses through the application of a new and innovative technology.

Jan 1, 1993

By Milton H. Ward

The percentage of exploration dollars flowing out of the industrialized countries continues at an all-time high, and this shift in risk money is justified (Samuels, 1990; Bosson, 1977). Clearly, the odds of discovery are greatly enhanced if exploration is pursued in an untrampled and geologically more prospective environment. Unfortunately, such major unexplored areas of the developed world are shrinking rapidly, not just because the lands have already been tested, but primarily because they have been withdrawn from exploration. Experience, however, has shown that foreign investment is not without risks. These include problems that result from working in isolated areas, a lack of infrastructure, untrained workers and an absence of a solid geological data base. While the likelihood of once-feared expropriation is now low, mining enterprises still must take precautions to gain the support of their constituencies, including a variety of governments (local, provincial and central), workers, environmentalists, cultural organizations and local landowners. Is foreign exploration worth the risk? In most cases, Yes! But maintaining tenure and long-term success in a less developed country is only likely with good planning and the use of appropriate safeguards. These include measures such as buying country-risk insurance, building multinational relationships, forming joint investments, developing a broad customer base and seeking local investors in the company (Cobbe, 1979). The primary theme of this lecture is: How a company handles its constituency is critical to long-term tenure in a foreign country. Ideally, a multinational mining company would be so effective in dealing with the local people and managing its relationship with the host government that it would become a preferred employer, preferred over its competitors and over local companies. Historical overview Our earliest ancestors lived in Africa three to four million years ago. The Paleolithic or Old Stone Age, about 500,000 years ago, marked the beginning of mining in its earliest form (Gregory, 1980; Wolf, 1984). Various types of rocks and stones were used for tools and weapons, with flint being the preferred resource for implements. Initially, these materials were collected as stones (eoliths) lying on the surface. Then they came from excavations of flint in limestone beds that were exposed in river banks or naturally occurring excavations. Later, more formal mining developed. No doubt tribes of the Old Stone Age experienced conflict over rights to eoliths, food and land. The question of who owns the land and has rights to its contents and what is fair value for extraction is still the subject of intense debate and, occasionally, open conflict. As time passed, the search for useful minerals required migration from one area to another. Later, voyages from Europe to the New World and travels to other remote regions were funded and supported by absentee investors, kings and such (Rogers, 1976). The primary objective of such funding was to obtain gold, silver, food stuffs and other commodities that could be collected from the new countries. This is still the objective of foreign investment.

Jan 1, 1994

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

Hydrodynamic investigations in exploratory boreholes and grouting holes are conducted for the purpose of obtain¬ing information about the hydraulic properties of the hydrostratigraphic section to be intersected by the proposed underground workings. The information obtained from the investigations provides the basis for calculating the hydrau¬lic coefficients of fractured permeable rock, the dimensions of the anticipated grout isolation curtain(s) around the un¬derground workings, the number and location of grouting holes, the injection pressure modes, and also the volume(s) of grout that will be required (Anon., 1976, 1978). The following data on each aquifer are obtained from the investigations conducted in monitoring and grouting bore¬holes and the analysis of the results: 1) the top of each hydrostratigraphic unit, 2) the thickness of each unit, 3) the ground water fluid potential distribution in each unit, 4) the coefficient of permeability, 5) the piezoconductivity, 6) the fracture porosity, 7) the geometry of the fractures in the rock, 8) the elasticity-compressibility coefficient of the fractured rock, 9) the chemical composition of the ground water, 10) the direction of flow of the ground water, and 11) the expected inflow rate of water into the shaft, drift or tunnel. STG uses its DAU-3M type flowmeter to conduct in¬vestigations of directions of flow in vertical, inclined and horizontal drillholes. The DAU-6 instrument is used to de¬termine the direction of flow of ground water in each frac¬ture or fractured aquifer. Various singular and double DAU type packers are used for pumping and for injection studies (tests) and for flowmeter investigations. Normally the instruments enumerated above permit in¬vestigations to be conducted in each separate aquifer with¬out reinforcing the holes with casings. On the basis of these investigative data, both the hydraulic properties of unfractured rock and the hydraulic properties of the fractured rock are estimated. Dual porosity rocks require special attention because they tend to segregate the grout. 3.1 FLOWMETER INVESTIGATIONS IN BOREHOLES The STG flowmetric methodology is based on the mea¬surement of the ground water flow rate through the borehole by hydrostratigraphic interval after the disturbance of the hydrostatic equilibrium in the "hole-aquifer system" (after pumping or injecting). The relationship of the head changes to the discharge into or from a particular hydrostratigraphic unit obtained during the tests serve as the basis for calcu¬lating the hydraulic properties. Flowmetric investigations facilitate the determination of the number of aquifers, their depths, their thickness, the hydraulic properties of the fractured rock and the magnitude and direction of the flow of ground water. 3.1.1 FLOWMETER HARDWARE STG conducts flowmetric investigations in boreholes using its DAU-3M-108, DAU-3M-73, DAU-3M-57 and DAU-3M-44 instruments.' They have respective external diameters of 108, 73, 57 and 44 mm. The type of flowmeter selected for use depends on the borehole geometry and the technological scheme for carrying out the investigations. Boreholes with a drilling diameter of 76-93 mm are inves¬tigated with the DAU-3M-73 flowmeter; boreholes drilled by bits with a diameter of 112 mm and more are investi¬gated using the DAU-3M-108 flowmeter. The DAU-3M¬108 and DAU-3M-57 instruments are used for flowmetric investigations with a packer. 3.1.1.1 The Downhole Sensor The sensor design of the DAU-3M-73 hole flowmeter is shown in Fig. 2. The design of the DAU-3M-108 instru¬ment is similar to the design of the DAU-3M-73 instrument. The frame of the flowmeter sensor shown in Fig. 2 consists of a casing, an upper and lower centering mount and two rings to which the guiding rods are attached. The upper rods are built into the connector bushing; the lower rods are built into the coupling sleeve. The borehole cable is attached using a half-coupling, a packing ring and a constriction nut. Thus, the frame of the flowmeter sensor is made so that the free passage of water to the impeller is facilitated along with the necessary rigidity. The primary moving component of the flowmeter is the double-bladed impeller, which rotates on cobalt-tungsten pivots and agate thrust bearings. Special extended air cham¬bers protect the supports of the impeller from the action of the borehole fluid which may contain fibrous and abrasive particles. The air located in the chambers shields the sup¬ports from direct contact with the borehole fluid when the sensor operates in a borehole. The hollow casing of the impeller serves the function of a lower cap. The upper cap is attached to the casing using a threaded connector; it is affixed also with a lock-nut. An adjusting screw with a

Jan 1, 1993