Search Documents

By C. C. Graham

In this paper, the problems which occurred on introduction of dense medium cyclone coal washing in Australia are reviewed together with the subsequent measures taken to obtain a satisfactory magnetite. Specification and testing of magnetite for exploration, quality control and in-plant check purposes is discussed. The disposition of Australian magnetite deposits in relation to the main coal producing areas is examined, and comments are made on the economics of mining, milling and beneficiating magnetite for coal preparation uses alone. Future trends in the Australian Coal Industry are predicted, and the need for a planned approach for the future is demons traced.

Jan 1, 1982

By M. L. Young

Hindered settling columns are used throughout the minerals industry for both size and density separations. In this study, the performance of a continuous, laboratory-scale hindered-settling column was evaluated for various particle systems. The test variables included solids composition, water rate, and column height column performance was evaluated using partition curves and corresponding performance parameters.

Jan 1, 1999

By Dale C. Matthews

Pressure oxidation of refractory gold ores is becoming more popular in our environmentally sensitive society. This paper will discuss some specific process problems and solutions involved with starting up and operating an autoclave circuit.

Jan 1, 1991

By William A. Wallace

Common mineral resources (sand, gravel, crushed stone, etc.), which are so necessary for the construction of metropolitan areas, are rapidly being depleted or otherwise rendered unavailable in the very areas that need them most. However, the problem of planning for these resources involves a number of independent and dependent variables that must first be defined and related. Finally, a dollar value must be assigned where possible. Complex interrelationships between the variables and their dependence on outside factors has made mathematical "solution" of the problem of planning for non-renewable mineral resources difficult at the present time. Therefore, the use of computer simulation is suggested as a means by which this complex problem can be investigated. The purpose of this paper is to report on a continuing research program whose objectives are: (1) to delineate the factors involved in planning for the utilization of common mineral resources in urban-suburban environs; (2) to construct a planning model for these materials amenable to computer analysis, (3) evaluate the model by using test cases, and (4) perform a sensitivity analysis to determine the initial parameters in future planning for these materials.

Jan 1, 1968

By T. O. Kuhl

The Royal-Mountain King Project is 7.2 kilometers (4.5 miles) northwest of Copperopolis, California. Reserves of 8,250,000 t (9,100,000 st) at 2.32 g/t (0.068 oz/st) gold will be processed at 2500 t/d (2750 st/d) from three pits. Production is scheduled to begin the first quarter of 1989. District geology consists of northwest trending sequences of Jurassic meta-sedimentary and meta-volcanic rocks. Three ore bodies are located along the Hodson fault which trends northwest and dips 40 degrees northeast. The Gold Knoll and North Pit ore bodies are hosted in carbonate and silica altered meta-volcanic rocks whereas the Skyrocket ore body is hosted in quartz stockwork zones in meta-sedimentary rocks. Gold is present as inclusions and micro-veinlets in pyrite.

Jan 1, 1989

By Mark Cadzow, Rodney Lamb

CARBAD is a recently developed Australian process for the recovery of gold and platinum group metals (PGM). The process relies on the selective agglomeration phenomena of the gold and PGM to capture the mineral in a carbon-hydrocarbon media. The precious minerals are then extracted from the loaded media by a solvent gold room process producing a relatively pure concentrate. The media is then reformed and recycled. The process development from batch test work to a 5 t/h commercial scale CARBAD plant is discussed. The operation and results of processing a variety of ore types at several alluvial and hardrock gold mines is examined. The operating and capital costs for the CARBAD process shows that it is significantly less than that the conventional CIP/CIL. The environmental safety of the process is a major feature where precious metal deposits are located within urban environments or within wilderness areas.

Jan 1, 1989

By Stephen P. Winkelmann

The expansion of gold production in Nevada's Carlin Trend over the last few years has been staggering. To increase gold production while minimizing capital requirements and providing for the safe and efficient mining and processing of ores has required a tremendous effort by the mine engineering group at Newmont Gold. Organizational changes were implemented by the company to effectively deal with a full range of engineering problems. Specially developed computer software and its applications will be explained in this article as well as improvements in the techniques used in converting geologic resources into reserves. Scheduling procedures for the mining of multiple pits to feed multiple processing facilities will likewise be presented. Ore control procedures and current mine engineering practices are discussed. Growth at Newmont Gold Expansion of production levels at Newmont Gold Co. was brought about primarily by the economic incentive to exploit increased reserves. From 1987 to 1989, mined production increased by 260%, gold production by 238%, and manpower by 166% (Table 1). These increases came quickly and demanded

Jan 1, 1990

By T. Faulkner, S. A. Richards

"Classic engineering economics provides the mining engineer with a fundamental approach to choosing between capital spending alternatives. This approach has been heavily used over the years and is an accepted technique for most investment decisions. There is a shortcoming that I have run into over the 15 year period when I worked in business planning roles. The classic time value of money approaches such as Net Present Value, Return on Investment, and Internal Rate of Return provide good estimates, but the input assumptions may fall short of describing the real material differences required by these analysis techniques. If the cost benefit analysis is defined solely on the improvement of the item being replaced or improved, the true profitability of the decision may be overestimated. Productivity improvement based capital projects can yield more accurate forecasts when conducted in concert with a “bottleneck analysis”. INTRODUCTION A review of the Theory of Constraints, (Goldratt, Cox, 1984) Lean, (Womack, 2003) (Rattner, 2006) and Six Sigma (Cryger, DeFeo 2015) lead us to recognize that these process improvement methodologies are oriented to the manufacturing process. These systems generally involve a factory that the material moves through on the way to becoming a final product. The mining challenge has many similarities to manufacturing once the ore has been won and made ready for processing. Before that point, however, the process is somewhat inverted while the ore is being won. Instead of the material moving through the factory, the factory is moving through the material. The Theory of Constraints (TOC) was used in an underground context by Baafi, Cai and Porter at 2015 APCOM, but even this groups’ analysis did not carry the concept from mining to shipping of the final product. There can be spatially distributed data that can affect the mining throughput constraints, some of which can be determined from exploration results. Identifying constraints can lead us to mapping productivity bottlenecks on future mining. Knowing this may improve decision making by eliminating one of Jim Fishbein’s three deadly sins of strategic planning: incomplete planning. When evaluating capital investment alternatives you should evaluate the impact of any proposed improvements on the entire operation. At the core of any mining system is the materials handling system. This can be typically expressed as the system that handles the raw material from the “face” through processing and then handling the finished product as well as the waste material. A “Bottleneck Analysis” is an investigation into the factors limiting a material handling system’s productivity (Goldratt, Cox, 1984). Mining material handling systems are usually composed of several linked components such as draglines, shovels, loaders, hydraulic excavators, continuous miners, longwalls, highwall miners, bucket wheel excavators, LHDs, feeders, conveyor belts, stockpiles, crushers, processing plants with various circuits, and waste handling systems. Each of the aforementioned components has a slightly different throughput capacity. When these are linked in series, the one with the lowest throughput capacity limits all of the others, creating the bottleneck for the system. Every material handling system has a bottleneck. In the mining environment, a subtle, but very significant phenomenon may also occur. The bottleneck may change as a result of a change in the raw feed qualities, face recession, overburden depth, digability, learning curve, and many others factors which may be derived from the drillhole data. These parameters often change as a function of the location in the reserve base, and may also vary with time."

Jan 1, 2016

By Y. Luo, S. S. Peng

Based on the concept of slope-stability analysis, a formula for determining an important parameter required in the mathematical model for the prediction of mining subsidence in hilly terrain is proposed. The slope geometry and the physical and mechanical properties of the soil at the surface of the natural slope can all be considered in the formula. Incorporation of this new formula into an existing mathematical model provides an integrated approach for the study of ground movement in hilly regions.

Jan 1, 2000

By Joseph M. Morrison

This paper offers a comprehensive solution to the problem of dust emissions at belt conveyor transfer points. It discusses details of enclosure design and presents a straightforward procedure for calculating required dust control exhaust volumes. Many design variables are taken into account which heretofore have been commonly ignored or inadequately considered. These include belt widths, belt speeds, enclosure openings, material flow rates, material bulk densities, material lump sizes, height of material fall, material temperature, and ambient air temperature. All of these quantities are handled by means of a "fill-in-the-blanks" type of calculation form which permits quick, reliable solutions by relative "non- experts".

Jan 1, 1970

By Randal J. Barnes

Computer based techniques for solving the Ultimate Pit Limit Problem have appeared in mining literature since the early 1960's. The majority of papers pertaining to this subject can be partitioned into one of two categories: discussion of the pros and cons of a particular algorithm, or a case study presenting specific applications of an algorithm. Subsequently, there has a1 so been considerable debate concerning the best techniques between, essentially, two camps: those favoring the moving cones techniques, and those favoring the techniques which yield true optimal pit designs. The purpose of this paper is not to add to this debate, but rather to present a few new ideas (partially a new look at an old idea), which can be easily implemented to noticeably improve any ultimate pit limit approach independent of the particular algorithm used. These ideas fall under the heading of "bounding the optimum" (Barnes and Johnson, 1980).

Jan 1, 1982

By James A. Hartlage

Work on the design of Kelex 100 was initiated several years ago at the Research Laboratories of Ashland Chemical Company. The effort was specifically directed toward the synthesis of an organic molecule which would strongly and selectively chelate copper ions in acidic solutions and form an oil soluble complex which would be stable in contact with an aqueous phase having a pH of approximately one. This publication describes efforts to establish data which could be used to estimate the economic utility of the new reagent. For helping to accomplish these ends, the author wishes to acknowledge the assistance of Mr. A. V. Henrickson of Hazen Research, Inc. for gathering a portion of the data presented here and to thank the copper companies who supplied leach solutions for studies described in this paper.

Jan 1, 1969

By Earl M. Frizzell

Investigation of mined land characteristics, evaluation of irrigation systems and evaluations by the mining industry determined that irrigation is a feasible method for aiding the revegetation of coal mined lands in the western arid and semi-arid regions (Sherman, et al. 1980). The various regions studied displayed a commonality of characteristics which enables, independent of the site or region, the recommendation of solid-set irrigation. Irrigation should be supplemental by complimenting natural precipitation and should be implemented on a temporary basis. For germination, the vegetation requires application of small amounts of water in a gentle, frequent, and timely manner. For the establishment phase of growth, moisture should be applied and stored in the soil either through pre-irrigation or deep irrigation.

Jan 1, 1985

By W. A. Hoyer

Neutron activation analysis for mineral identification has attracted the attention of numerous investigators, judging from the publications on this subject in the past few years. 1-9 The appealing aspect of this method of mineral analysis is its proven sensitivity in the laboratory. In principle, activation analysis is one of the few petro-physical methods whereby a direct analysis for a mineral itself is possible in a borehole. The successful application of activation analysis requires the use of particular neutron reactions, measurement of selected gamma-ray energy intervals, and optimum bombardment and detection times. For copper analysis, Labanov et al., 10,11 using a low-energy PuBe source, reported an acceptable logging means. On the other hand, Pradzynski12, in analyzing ores and process tailings, used high-energy neutrons and photons for surface measurements of process samples. The work of Labanov et al. was based on measuring the rate of decay of the activated copper and hence was not as definitive as might be desired. Equipment is commercially available to carry out activation studies in the field 13,14 Gamma-ray spectra can be successfully transmitted over ordinary logging cables and, with borehole high-energy neutron accelerators and lower-energy chemical neutron sources, a variety of neutron activation methods can be studied. The purpose of the study discussed in this paper was to determine the feasibility and practicability of logging for copper using neutron activation techniques and commercially available equipment. The laboratory study showed that Cu could be detected in rock samples in the laboratory by high-energy neutron activation of 63 Cu. In the field, however, due in part to the large volume irradiated, the direct detection of copper using high-energy neutrons was not as promising. Detection of copper by measuring both the direct gamma-ray emission and the excessively strong low-energy gamma-ray absorption appears promising. Copper was not detected either in the laboratory or

Jan 1, 1972

By S. J. Swan

A computerized on-line process control system designed to monitor and control the seven-cone copper precipitation operations at Kennecott Copper Corporation's Chino Mines Division in New Mexico has been continuously operating since April, 1972. The cone monitoring system consists of plant sampling components, process measurement instrumentation, on-stream X-ray spectrometer, control computer, typewriters for programming and for operating reports, foreman's communication console, and cone automation hardware. The system provides the following functions: (1) assays for copper and iron from ten process streams on a continuous rotating basis, (2) directs hardware to automatically flush and start up cone units based on measured performance variables, (3) provides continuous plant operating data and calculates metallurgical averages as well as production figures for shift and daily summaries, and (4) provides data logging capabilities. The system is very reliable and improves plant performance by increasing yields, reducing scrap iron consumption, and reducing operating manpower requirements.

Jan 1, 1975

By V. R. Degner

Given: the process tonnage, performance objectives, and plant floor area, the paper will outline the metallurgical and machine hydrodynamic scale-up procedures for translating the lab flotation test results to the design of a full size flotation machine installation, including the machine number, size, and arrangement. Machine selection considerations for rougher, scavenger and cleaner duty, and special considerations relative to specific applications, will be summarized where appropriate. The value of kinetic modeling in quantitative metallurgical (lab to full size machine) scale-up will be reviewed considering a coal installation, and design information for additional applications such as copper, molybdenum, iron, phosphate, and potash will be discussed.

Jan 1, 1986

By Evangelos Spyridonos, Thomas Frommer, Wolfdietrich Skala, René Prissang

Operational grade modelling is a technique that uses production data to run daily updates of property models. It will enable mining engineers to use property predictions based on the most recently acquired data as support for quality control and decision making. The approach necessitates that the properties of the run- of-mine material can always be attributed to individual mining blocks or charges. The software employed must be highly reliable, because a system failure or the loss of data could seriously affect the mine's quality management. An operational grade modelling system has been developed for the Breitenau magnesite mine. It makes use of the Linear Octree Based Property Modelling system which was conceived and realised at the Free University of Berlin. This paper describes the system design and gives an account of the experiences during the first six months since system start-up.

Jan 1, 1996

Power cable costs are only a small part of total mining costs. So many mine operators consider power cable failure and resultant downtime as part of the cost of doing business. But, viewed in terms of lost production, these costs can be quite significant. Now one company, Cablec, seeks to cut cable costs by upgrading the polymer compounding process used to make cable insulating and semiconducting materials. Cablec is the leading manufacturer of electrical power cables in North America. And with about a third of the market, Cablec is the largest supplier of power cable to the mining industry in the United States. To improve its products, Cable has entered the polymer compounding business. In July, it began producing insulator and semiconductor polymer compounds at its plant in Indianapolis, IN. "This new facility provides a quantum leap over conventional compounding methods," said Harry C. Schell, Cablec's president and chief executive officer. "The Cablec polymers plant is producing a dramatically higher standard of polymer compounds that provide significantly higher levels of performance and improved life cycle costs for power cable." Cablec faces tough foreign competition in the wire and cable business. Competing on price alone is difficult, particularly when foreign producers are state subsidized. So Cablec feels the best way to compete is to establish new quality production standards. The company's new polymers plant is one way to do this. By increasing purity control and uniformity in polymer compounding, Cablec says its power cables will last longer and fail less often. A typical medium voltage cable consists of a conductor, conductor shield, insulation, insulation shield, metal shield, and jacket. The conductor shield and the insulation shield are conducting polymers. Contaminants and imperfections can occur within the insulation, at the conductor shield/insulation interface, or at the insulation shield/ insulation interface. Over time, these contaminants and imperfections can decrease the electrical strength of the cable or cause premature cable failure. The effort to minimize the number and size of any possible contaminants begins with pure polymer compounds mixed in a clean facility. However, most power cable manufacturers manually handle raw materials, use ethylene/propylene (EP) in bulk bales, and mix polymercompounds in open Banbury mixers. The quality and uniformity of polymer compounds is also impacted by temperature variations in the mixing process. This results in wide gradations of product consistency from batch to batch and ultimately contributes to power cable failure. Cablec says the improved polymer compounds from its state-of-the-art plant will be the purest and most consistent insulating and semiconducting materials available. The plant itself RCA spent $18 million to build Cablec's Indianapolis plant. RCA used the facility to mix specialty polymer compounds used to make video disks. RCA had two considerations in mind for the plant, cleanliness and uniformity of the compounds. However, when the video disk market failed to materialize, RCA sold the 46.5 dam 2 (50,000 sq ft) plant to Cablec for $3.1 million. Cablec invested an additional $3 million for modifications and increased production capabilities. Today's replacement cost for such a facility is estimated at $30 million. Cablec says the plant will set a new standard for performance and be economically difficult to duplicate anywhere. One of the essential elements of the plant's clean process environment is the air intake system. It filters contaminants greater than 2 um, less than one-fiftieth the current industry standard. All material handling and conveying areas in the facility are air-locked. This keeps out contaminants such as smoke, dust, and pollen. Banks of pneumatic pumps move polymer components through the system and continually filter the air. The plant also has a backup air intake system. No process downtime due to pump failure here. From the time raw material enters the plant, it is stored, transported, and processed in filtered air by an airtight stainless steel system. The stainless steel resists rust and corrosion. This further eliminates the danger of contamination from paint or rust particles in the conveyance network. A computer system allows a single operator in a central control room to monitor every aspect of the compounding process from air quality to line speed. The computer

Jan 12, 1988

By Gary P. Marshall, Jeffery S. Thompson, Robert E. Jenkins

The effectiveness of the new DuPont Passivation Technology in eliminating acid generation from iron sulfides is presented. Passivation is achieved by treatment with a dilute basic perman­ganate solution. This treatment produces a thin impervious layer of iron/manganese oxide on the sulfide surface, providing a bar­rier to the environment so that the sulfide is not available for undesirable reactions such as the production of acid.

Jan 1, 1998

By Christian F. III Baiz

Introduction A new mining agenda is before us. Born of government policies and world economies, the years ahead will show reduced growth. Metals, mining, and most other natural resource industries are inflation dependant and capital intensive. For these, a long period of contraction of outmoded and costly capacity will evolve. In some cases, this will be supplanted by new, lower cost capacity. But this will occur only if the cost of production - including cash operating and debt service costs - comes in at or below current market conditions. The industrial outlook for metals mining can be characterized as bearish. A US bank economist said mining companies planning their five-year forecasts should take current market conditions and straight-line them to the end of the decade. With low growth and low inflation, the real price of metals will remain flat or decline slightly. As a result, capital funding will be problematic. The low-cost producer will succeed. That means only the producer with low cash costs and low principal and interest costs per unit of production, will succeed. Gaining a perspective One must look back 30 years to see the evolution of the capital markets, for metal mine financing. This period can be divided into two economic periods. The 1950s were a time of stable economics. Mining companies earned and reported good profits. They had good corporate creditworthiness. In essence, mining companies of the 1950s were highly self-reliant. When equity infusions were needed, they were easily obtained. Financial management kept long-term debt low. Fixed rate, long-term financing was readily available in the long-term bond markets. The commercial banks of the 1950s were rarely used by the mining industry. When necessary, mining companies went to the banks for short-term financing - the kind that was needed for working capital requirements. Changing rhythms In the old rhythm there was an orderly market. Even into the mid-1960s, 75% of world annual copper production was controlled by eight companies: two in the UK, one in Belgium, and five in the US. During times of poor market demand, these producers would control supplies to the market. They took their losses out of retained earnings. Capital was easily restored during the ensuing good times. The new rhythm called for copper to be an economic means to a political end. Third World copper producers brushed aside the market fundamentals of commodity economics. Yet, the political solutions of these countries - their lack of response to the market - have seldom achieved their original objectives. Each commodity has its own old and new rhythm. Aluminum may have a similar rhythm, coming 10 to 20 years later than copper. By the late 1960s, changes were occurring. Inflation was on the rise. Ore reserve quality was falling. As a result, capital expenditures were necessary to maintain existing output. These costs created an increase in corporate leverage, thus adding to inflation and rising interest rates. Indicators A comparison of the gross national product (GNP) deflator index, consumer price index, and the metal mining deflator index is instructive. (Fig. 1 and Table 1). With 1972 equal to 1, note that the metal mining deflator reached its lowest point in 1967. From that point, the metal mining deflator has accelerated severely for 16 years. Only two minor downturns occurred during the business recessions of the mid-1970s and the early 1980s. In essence, Fig. 1 shows that while GNP has grown modestly, a miner's dollar in 1972 would require $3.48 in 1980. This is an almost 17% compounded growth rate over that eight-year period. Beginning in the late 1960s, for the first time in mine financing, the risk of success shifted from the corporate balance sheet to third parties. Limited-resource financings were taken up by banking syndicates that accepted certain of these risks. The lender needed to be well acquainted with the types of risks to be evaluated. These include resource quality and quantity, construction and completion, capital and operations costs, market risks, force majeure, and political and exchange rate risks. Project financings became the basis whereby mining companies were able to maintain their borrowing capacities. In essence, the lender was willing to share some of the project risk while only receiving lenders' returns on these investments. Over the last two decades, mineral project financings have become highly complex transactions involving multicurrency, multi-

Jan 8, 1985