Search Documents

By Behzad Khorshidi

"The ultimate objectives of the post-tensioned strands are to connect the precast segments into a ring and provide pre-stress in the tunnel circumference. The method involves inserting the strand through the preliminary embedded duct in the precast concrete segments and then tensioning the strand by jack and fastening it. The post-tensioned strand eliminates the necessity of bolt connections between the segments and may reduce the labor cost and increase speed of lining construction. Pre-stressing of the segmental lining reduces the steel reinforcement or fiber volume in precast segments and/or thickness of the precast segments which would result in reducing the manufacturing cost of them. Pre-stressing would reduce cracking and increase water tightness, and would provide smooth intrados due to eliminated bolt joints and pockets in the tunnel lining. Pre-stressing would increase resistance to internal pressures as well. Further, this system could work very well structurally in tunnels with squeezing rock or tunnels with high seismic loadings. INTRODUCTION OF THE METHODPost-tensioning is commonly used in the construction of bridges, large buildings, nuclear power stations, and water tanks but its utilization in tunnels is still in its infancy.The precast pre-stressed concrete segmental lining can be used for shield tunnels. It provides a reinforced lining ring by the following construction stages and as shown in Figure 1:1) Segments to be assembled by TBM to complete a full ring2) Steel strand to be inserted through embedded duct (sheath) within the segments3) The strand to be tensioned by Jack after anchorage of the other end4) The strand to be fastened after reaching required tension load5) The horizontal strands (if necessary) to be installed, tensioned and fastened6) The recesses and gap between strand and duct to be filled by groutingFurther, Figure 2 shows an unbonded post-tensioning strand model; Figure 3 shows an anchor sample (Xanchor); Figure 4 shows a duct (sheath) and anchor within reinforcement; Figure 5 depicts the posttensioning of a strand by jack; and Figure 6 is an image of the Midorigaoka Trunk line tunnel in Sagamihara, Japan which was constructed using this system."

Jan 1, 2016

By R. K. Will

An inactive mining operation in northern California is known to be a source of acid mine drainage and heavy metals which have impacted adjacent creeks. Elevated concentrations of copper and zinc are a concern to aquatic populations, particularly steelhead trout and salmon downstream in the Sacramento River. Previous regional geological surveys of mineralization by the U.S. Geological Survey located and mapped outcrops of massive sulfides and gossan. Recent investigations indicate that a substantial amount of the metals in the local creeks are due to natural causes. The investigations include locating and mapping surface and subsurface minerals, soil and water sampling, and chemical analysis. Groundwater, seeps, and surface water were also sampled and analyzed. A water balance was conducted on a sub-basin level following delineation of surface water drainage and groundwater divides. A chemical mass balance incorporated metal concentrations and water volumes and was then used with other data to determine the contribution of metals from natural versus mining-related causes.

Jan 1, 1998

By James A. Decker

Hanna has developed three production planning systems to help the mine engineers determine the sequence of mining from available ore supples. The Production Scheduling System was developed to give the staff a tool for long range planning by sequencing the removal of blocks from an open pit property. It was needed to determine the year of removal for each block so that the optimum present-valued pit limits could be established by our pit design program. Since in this type of planning short term grade control is less of a factor than it is in daily or monthly planning, the system gives the program greater control and more latitude in block selection. It permits only full blocks to be taken.

Jan 1, 1984

By L. H. Munson, E. H. Carbaugh, D. E. Hadlock, L. F. Munson, R. L. Gilchrist

As a result of the Three Mile Accident and because of evidence indicating radiation protection problems, the U.S Nuclear Regulatory Commission (USNRC) undertook a major effort, with the assistance of the Pacific Northwest Laboratory (PNL), to analyze radiation protection programs at 47 commercially operated nuclear power plants. This effort, the health physics appraisal program (HPAP), using a modified management oversite and risk tree analytical logic methodology (MORT) which consisted of analytical trees with applicable questions for each tree, was subsequently extended to include USNRC licensed uranium mills. In the uranium mill appraisal, a team of four senior radiation safety professionals spent a week at each mill evaluating the total health physics program. Prior to the HPAP, the USNRC inspection efforts were designed to determine if the licensees were fulfilling the requirements of the code of federal regulations and the mills source material license. The HPAP, however, was designed and structured to facilitate an integrated look at the total program. It is also directed into areas for which explicit NRC regulatory requirements may not currently exist. The latitude of the HPAP was designed to allow professional judgement in the evaluation of program adequacy, because merely meeting the explicit regulatory requirements does not necessarily ensure an adequate and effective health physics program. The results of the first eight site visits and the generic health physics problems identified within the uranium milling industry will be identified in this paper.

Jan 1, 1981

By H. C. Juvkam-Wold

The design of an aquifer depressurization system is discussed. The system uses a number of wells surrounding a mine shaft to reduce the aquifer pressure in the vicinity of the shaft. The effect of various parameters such as number of wells, wellbore diameter, time and well location is discussed. It is concluded that, with a properly designed depressurization system, the aquifer pressure and the water inflow rate to the shaft may be reduced to less than 15X of their potential values in the absence of wells

Jan 1, 1980

By R. L. Loofbourow

SEVERAL categories of storage are used depending on capacity. Operational storage, which is small in comparison with the market, facilitates handling surges of a few hours' or a few days' duration. Seasonal storage, usually larger, permits accumulation of product during sea- sons when demand is low, for delivery when demand is high. In producing areas, large storage may permit production at a uniform rate, without waste or distress sale. Near large markets such storage increases the efficiency of transportation, allows a more extensive or higher grade market to be served, and affords protection against interruption in delivery.

Jan 1, 1959

By James P. Savely

This paper describes the development of a trim blast design to improve the stability of a final pit wall. Description is given of the effects of rock characteristics, rock type, and pit plans on the blast design. Currently, six benches have been mined with trim blasting. A more stable final wall has resulted and the successful program has reduced mining costs over an extended time period. Low cost blast monitoring and field observation were used to determine peak particle velocity and blast damage. Using criteria developed from this relationship, trim blasts were designed and evaluated.

Jan 1, 1986

By Mario E. Rossi

Often geometallurgical models are prepared at various project stages from very few data and are assumed to be representative of very large tonnages. These may include recovery models; crushing and grinding parameters and models; models of concentrate grades; models of acid consumption; etc. These models commonly do not carry a measure of uncertainty or variability, and are taken at face value at the time of design and planning. This paper proposes a proactive approach to modelling variability, providing uncertainty estimates and thus allowing for risk analysis and mitigation of geometallurgical models. The variability model is built up by understanding the limitations of the pillars of a geometallurgical model: data uncertainty; geologic model uncertainty; domain definition uncertainty; and parameter estimation uncertainty. Of these factors, typically domain definition is the most significant contributor to geometallurgical model variability. First, the fundamental supports for these models are briefly discussed, with domain definition emphasized. Second, two methods for uncertainty modelling are proposed. The first, more applicable to conceptual or early-stage projects, is a simpler and more expedient alternative that provides initial assessments of variability. This is intended to aid management in decision-making related to budgeting, including further sampling and testing. The second, a block-by-block approach that allows a detailed assessment of risk for specific designs and mine plans, thus providing further opportunities for mitigation. In the example provided, emphasis is placed in communicating this variability to both management and technical personnel in the form of “measured-indicated-inferred” indicators and also block-by-block confidence intervals.

Jun 25, 2023

"From April 22 to 28, the eyes of the tunneling and underground construction world will be on San Francisco, CA, as the world’s most influential underground construction industry leaders gather at the Moscone Center for the 2016 World Tunnel Congress.Recognized as the most important international annual meeting for the industry, the 2016 version comes to the United States for the first time in 20 years and will be hosted by the Underground Construction Association of SME (UCA of SME). The conference will be held in lieu of the UCA’s biennial North American Tunneling Conference and will bring the strengths and resources of the UCA of SME and the International Tunnelling and Underground Space Association (ITA). The result will be a conference with unmatched technical programming and a showcase of more than 200 exhibiting companies.A program committee led by Randy Essex of Mott MacDonald, Lonnie Jacobs of Frontier Kemper Constructors, Michael Mooney, of the Colorado School of Mines, Priscilla Nelson, of the Colorado School of Mines and Amanda Elioff of Parsons Brinkerhoff formed the program committee and worked for more than two years to build the program. The result is four technical sessions with five tracks in each session and 185 oral presentations.“One challenge was the sheer size of the group that would be assembled, perhaps 2,500 attendees or more, and the large number of abstracts we were likely to receive,” said Essex. “ We investigated extending the conference a fourth day, but that was not workable with the Moscone Center. We settled on having five concurrent technical tracks – something that has not been attempted in past NAT or RETC conferences to my knowledge. The next step was to develop suggested session titles that would span the breadth of subjects that would interest conference attendees as well as serve the conference theme.”"

Apr 1, 2016

By Roberto Pimentel de Souza

Since 1976 CVRD is carrying out tests to develop a type of pellet made with organic binder. One binder that showed good possibility to be used in industrial plants is Peridur. An extensive framework of tests was run in CVRD's pilot plant. The results are presented in this paper. Finally, the decision was taken to carry out an industrial production of 50.000 t of pellets. It was scheduled for March '81. The results are shown in this pager. It was not observed any detrimental effect of the peridur neither in the process nor in the product quality.

Jan 1, 1981

By John Newby, Mahmood Khwaja, Bernard Theron, Janice McGovern, Bernard Catalano, Michael S. Schultz

Launching a full-size pressurized-face Tunnel Boring Machine (TBM) in difficult ground conditions is always challenging. Recently, few projects have innovated the process by scaling the trenchless method of pipe jacking, and modified steel bell approach, to facilitate the launching of a full-size TBM without the need for large and deep trenches, starter/tail tunnels, or for incrementally installing supporting gear as the machine advances. This paper presents three such projects; evaluates the post-bid contractor proposed modifications; details the innovative use of pre-cast pipe segments to facilitate machine launch; and, provides an overall assessment of the benefits, challenges and lessons learned related to the modified approach.

Jun 13, 2021

By Fred T. Towne

There are a number of air classifiers manufactured throughout the United States and the rest of the world. The classifiers manufactured by Alpine, A. G. of Augsburg, Germany, are unique in their abilities. It is this uniqueness that I wish to delve into and in this respect we will limit this discussion primarily to the classifiers as manufactured by Alpine. It has been reported in the past that these classifiers were introduced into the. United States in the late 50's. Until the introduction of the Alpine Classifiers, air classification seldom produced a satisfactory fractionation of a product below 45 microns (325 mesh) or above approximately 22 mesh. It has been a common practice to classify fine materials which used water as a carrier medium The use of centrifuges are today producing thousands of tons of finely partitive powders in the very small particle size range. The use of centrifuges in connection with wet grinding mills has increased the rates of production of these mills considerably.

Jan 1, 1965

By Otto E. Zwanzig

You may think long before this talk has been completed that the speaker is belaboring the obvious. Please let me put to rest here and now any doubt which you may have in this regard by assuring you that is precisely my intent, and for a very specific reason. We all profess to know and recognize the obvious, but I am impressed increasingly how often we forget or fail to act upon the obvious. Shortly after starting my first job upon graduation from college, I was asked by my boss to participate in a course on practical communications, particularly as applied to conveying proposals effectively to the client -- be he customer or company president. The concept or philosophy underlying this program was so simple and obvious that in my youthful brashness I saw only a gross waste by the company of e good, solid $1930 in compelling me to take the course. The sequel to this experience occurred about five yews ago when I was directing a 300-man marketing group. At that time I enrolled a dozen of my department heads, and subsequently about a hundred other personnel, in the contemporary version of that sane program. Why? -- because they all knew the obvious, but I could see how imperfectly they were implementing it. Truly, a wide chasm exists all too often in our beliefs on the one hand and our practices on the other.

Jan 1, 1962

By P. M. Hawley

Kennecott Corporation, in joint venture with Galactic Resources Ltd., recently began operation of an open pit gold mining and milling facility near Columbia, South Carolina. The deposit consists of two ore bodies (North and South deposits) hosted in deformed and altered meta-volcanics and meta-sediments of the Carolina Slate Belt. This paper describes the rock mechanics and engineering geology investigations conducted for design of interim, ultimate and final reclamation slopes for the South Pit. Emphasis includes the successful use of drill core orientation techniques to confirm complex geologic structure at depth; the development of a three-dimensional rock mass competency model, incorporating surface mapping data, results of bench mapping documentation, field index testing and laboratory testing; and kinematic assessments for design of optimum slopes.

Jan 1, 1991

By Bahaa Alyosif, Turan Uysal, Muhammet Kürsat Aydemir, MURAT ERDEMOGLU

 The paper investigates the effect of intensive milling on the conversion of microcline to potassium chloride during chlorination roasting. The study aims to improve potassium recovery by reducing the chlorination roasting temperature through mechanical activation.

Aug 1, 2023

By Richard R. Klimpel

INTRODUCTION The purpose of this paper is to summarize the current status of reagents used in the mineral industry plus present some current challenges and possible new technologies of the future. Table 1 lists the important families of reagents which, when taken together, constitute at least 95% of the current commercial reagent market. A very approximate estimate of the free world reagent market size in mineral applications is about 1.5 to 2.0 billion dollars (U.S.) using 1985 data. Obviously, to serve such a large market requires the effort of many different types of commercial supply sources. It is estimated that there are over 300 industrial firms in the free world that have a dedicated business/technical structure for supplying reagents related to the mining industry. There are a number of characteristics which are associated with the product families listed in Table 1. Understanding these characteristics helps to provide a realistic economic/technical basis for outlining future challenges in mining chemicals. 1.Essentially all of the products listed are old chemistry in the sense that the molecules have been known and manufactured for at least 25 years. This has not been a highly dynamic field of endeavor from the viewpoint of new product introduction. 2. The greater majority of the products listed can be viewed in commercial terms as "commodity" chemicals, that is, they are available from many sources and the pricing of a some- what generic product generally dominates differences in product quality or uniqueness. With commodity pricing, reagent suppliers significantly reduce research expenditures, loosen product quality somewhat if the applications of the reagents allow, etc. in order to be cost competitive.

Jan 1, 1989

By John F. Martonik

When OSHA came into existence in 1970, it adopted national consensus standards to improve safety and health conditions in work places. Coke oven emissions, which are proven to cause cancer and respiratory diseases, were regulated by the coal tar pitch volatile standard, adopted from the 1969 edition of the Threshold Limit Values for Airborne Contaminants by the American Conference of Governmental Industrial Hygienists. The coal tar pitch standard, based upon the benzene soluble fraction of total particulates, limits the personal exposure to 200 micrograms of the benzene soluble fractions of total particulate per cubic meter of air. This standard can be classified as a performance standard because only general limits are set which allows the employer to choose for themselves the means to comply. Both the United Steelworkers of America and the American Iron and Steel Institute petitioned the Secretary of Labor to write a new standard for coke oven missions, each thinking the coal tar pitch standard unsatisfactory.

Jan 1, 1980

By T. Hollenberg, N. Nolten

The mining industry is one of the major energy consumers in Namibia. Energy costs increase the operating costs of Namibian mines, in particular, the processing plants, and result in an overall increase of production costs. A substantial part of the energy used is directly imported from South Africa. The cost of energy has been increasing rapidly in the past few years and will most likely continue to do so in the future. In 2015, the average wholesale price for energy from national power utility NamPower was US$87/MWh after rising more than 12 percent annually in the two previous years. At peak times, which are early in the morning and late in the evening, imported-energy prices are extremely high and have to be factored into the electricity tariffs. This problem is expected to intensify due to a projected 4 percent annual increase in energy demand. A major target of the Namibian mines, therefore, is to consider possible ways to address energy-saving challenges and to investigate possibilities for the mines to generate electricity internally during peak times. This is in alignment with the mines’ strategic plans and objectives to reduce total energy consumption and costs from both national and foreign electricity suppliers. In this paper, we explore addressing some of the key energy consumption and optimization challenges through process energy reuse and solar energy production to decrease demand for imported energy through a case study carried out in cooperation with Skorpion Zinc Mine and Refinery.

Jan 1, 2018

By Mohamed Gamal, Bill Zietlow

"In oil fields that have been depleted with conventional surface oil wells but still contain significant reserves, an extraction alternative that has been constructed recently consists of a drilling gallery below the oil-bearing formation at the bottom of a 1,200-ft deep shaft where upward sloping wells are being drilled to allow oil collection by gravity. The gallery is 92-ft diameter with a flat ceiling supported by rock bolts and shotcrete structurally connected to the shaft liner, which doubles as a large tension support element. A special excavation sequence was implemented for the gallery to maximize arching in the stress above the large diameter gallery. The gallery was located in competent sandstone, constructed with sequential excavation methods, and designed with a 3D finite element model. Special consideration was given to optimizing the gallery location to take advantage of the geology for construction and support while giving good positioning to the well drilling equipment. BACKGROUND Brierley Associates was contracted to provide both design and construction management services for an approximately 1,165-ft deep, 18-ft excavated diameter vertical shaft that opens to a 92-ft diameter flat roof gallery. The geotechnical data for the site was based on information available from literature and from data obtained during core drilling and from in-situ testing in a 1250-ft deep borehole. Wire line coring was conducted using a HQ, 10-ft long core barrel with a mud-rotary drilling method through sedimentary bedrock. The geometry of the shaft and the bottom gallery is shown in Figure 1(a). GEOLOGIC SETTING AND STRUCTURAL GEOLOGY The stratigraphy at the site includes a series of interbedded marine limestone, shale, claystone, siltstone, sandstone, and chert units. Limestone and shale are the predominant lithologies in the upper approximately 675 ft, while the lower portion contains five distinct sandstone units and more abundant shale, claystone, siltstone, and coal than the upper zone. A cherty sandstone at a depth of 1,130 below ground surface (bgs) was encountered. At a depth of about 1,000 ft to 1,116 ft bgs, a non-marine sandstone unit was encountered. This sandstone is the hydrocarbon bearing layer. Joints and fractures observed in the limestone had dips ranging from 0 to 90 deg. from horizontal with joint and fracture surfaces that ranged from planar to irregular and smooth to rough. Several, near vertical shear planes with slickensides were observed with surfaces that were generally smooth and planar. RQD values for the limestone ranged from 0 to 100 percent but in general were good to excellent."

Jan 1, 2016

By H. H. Murray

New and improved beneficiation techniques are available to allow the production of clay minerals of exceptionally high purity. This is particularly true for kaolins and smectites. Wet processing techniques include particle size separation, high intensity magnetic separation, chemical leaching ,flotation, and selective flocculation. The blending of clay minerals with other minerals provides opportunities to make special ceramic materials such as cordierite and other minerals that have very special ceramic properties including low heat expansion, high fired strength, low absorption, and other desired qualities.

Jan 1, 1990