Search Documents

By Keith G. Wallace, K. M. (Chris) Chmura, Kirk H. McDaniel

The Waste Isolation Pilot Plant (WIPP) performed a feasibility analysis for the purpose of either modifying, supplementing, or replacing its two main mine fans. The WIPP, located near Carlsbad, New Mexico, is a U.S. Department of Energy (DOE) fa¬cility designed to demonstrate the permanent, safe disposal of U.S. defense-generated transuranic waste in a deep bedded salt deposit. Since the centrifugal fans were installed in 1988, multiple op¬erational and performance concerns have been identified. A com¬prehensive engineering study was conducted in 1995 to: 1) Qualify and quantify operational concerns, 2) Evaluate possible alternatives, and 3) Recommend an optimum solution. Multiple system modification and/or replacement scenarios were evaluated with associated cost estimates developed. The study considered replacement with either centrifugal or axial fans. Multiple fan duties are required at the WIPP. Therefore, Variable Frequency Drives and Inlet Vane Controls (IVC) were investigated for centrifugal fans. In-flight adjustable blades were investigated for axial fans. The study indicated that replacing the existing system with two double-width, double-inlet centrifugal fans equipped with IVCs was the best choice. This alternative provided the most desirable combination of: 1) ensuring the required operational readiness, and 2) improving system performance. The WIPP is currently planning to replace the first fan in 1997.

Jan 1, 1997

By W. R. Reed, S. Klima, J. Driscoll, T. W. Beck

"Tests were conducted to determine properties of four foam agents for their potential use in longwall mining dust control. Foam has been tried in underground mining in the past for dust control and is currently being reconsidered for use in underground coal longwall operations in order to help those operations comply with the Mine Safety and Health Administration’s lower coal mine respirable dust standard of 1.5 mg/m3. Foams were generated using two different methods. One method used compressed air and water pressure to generate foam, while the other method used low-pressure air generated by a blower and water pressure using a foam generator developed by the U.S. National Institute for Occupational Safety and Health. Foam property tests, consisting of a foam expansion ratio test and a water drainage test, were conducted to classify foams. Compressed-air-generated foams tended to have low expansion ratios, from 10 to 19, with high water drainage. Blower-air-generated foams had higher foam expansion ratios, from 30 to 60, with lower water drainage. Foams produced within these ranges of expansion ratios are stable and potentially suitable for dust control. The test results eliminated two foam agents for future testing because they had poor expansion ratios. The remaining two foam agents seem to have properties adequate for dust control. These material property tests can be used to classify foams for their potential use in longwall mining dust control. IntroductionAbout one-half of U.S. underground coal is produced by longwall mining, which allows for mining high volumes of coal but generates significant amounts of coal mine dust. This can lead to overexposures for longwall miners and possibly occupational respiratory diseases, including black lung and silicosis, which have no cure and can be disabling or fatal. The only method to avoid these occupational illnesses is through elimination of exposure to respirable coal mine dust and crystalline silica (quartz). The current occupational exposure limit for respirable coal mine dust is 1.5 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities (Mine Safety and Health Administration (MSHA), 2015a). When respirable quartz is present, the mine must maintain average concentrations at or below 0.1 mg/m3. If the mine exceeds the 0.1 mg/m3 respirable quartz dust concentration, then the applicable respirable dust standard is reduced, calculated as 10 divided by the percent quartz present (MSHA, 2015b)."

Jan 1, 2018

By Reed S. C. Rogers

The most widely used machines for grinding coal to the sizes prescribed for the pulverized coal firing of furnaces, boilers, and kilns are the vertical ball-race, roller-race and roller-bowl types of mills. However, the increased use of coal has led to an increased use of tumbling ball mills for coal grinding. Specifically, air-swept ball mills are now a part of many dry pulverized coal firing systems, offering the advantages over vertical mills of lower maintenance costs and the ability to handle strong or abrasive (high ash) coals. The current use of wet ball mills is to prepare coal-water slurries for direct combustion, although in time they may also find routine application for preparing slurry feed for coal gasifiers. In either application, wet ball mills ofer the advantages that coal grinding and wetting can be accomplished in a single step, and that the mills are readily used with fine wet screens to assure top size control in the slurry product. The simulation of tumbling ball mills with mathematical models has reached a fairly advanced stage, but the concepts have been applied only recently to coal grinding. As this paper will demonstrate, however, significant progress has been made in the use of models in ball mill circuit design for coal grinding. Included is a description of the techniques used for simulation, recommended parameter estimation methods, and demonstrations of process engineering calculations for large scale coal grinding circuits.

Jan 1, 1986

By A. Wang

This paper defines the elements of a basic economic model for decision-making when considering a methane drainage system for an underground coal mine. A drainage system will require significant capital and operating expenses; hence the decision to utilize drainage must be made carefully. The model outlines the basic structure of decision-making and considers the costs and benefits when the methane is marketed and when the methane is vented to the atmosphere. The effects on mine safety and the dust levels in the mine are also considered, both in a general format and as economic variables. Sources of information for executing this decision-making are provided for an actual mine decision.

Jan 1, 1997

By Richard L. Sanford

The generalized rail haulage simulator described in this paper is an outgrowth of the need to expand a previously developed single level simulator to permit analysis of production problems where intermediate car storage is used. Many of the ideas of the former single level simulator, which is an integral part of an Underground Generalized Materials Handling Simulator (UGMHS), have been used in model development. In addition, experience gained in applying the earlier model to a variety of operating conditions has been heavily relied on. The generalized rail haulage simulation model can operate as an independent system and, as such, can be used to analyze rail haulage systems using production distributions as data input. In addition, this model is designed to replace the present rail haulage sub-assembly in the UGMHS model and the linking procedure has been integrated into the model. The flow of coal from production sections in UGMHS, for example, fill the mine cars and a condition of no empty cars at a loading station will shut down in by production systems.

Jan 1, 1974

By R. Venugopal, V. K. Saxena, Veerendra Singh

"Ore morphology plays a vital role during the milling and liberation of minerals. This study was carried out to understand the role of mineral crystallography and mineral interfaces on the milling and liberation processes. Data related to mineral crystallography, Vickers Hardness Number and beneficiation processes were collected from literature, and detailed statistical analysis was conducted to relate these parameters. Review of the crystallographic information of minerals present in ores indicates that molecular weight and cell parameters significantly affect milling and liberation characteristics. Mineral interfaces were classified into the three categories of coherent crystals, semi-coherent and incoherent crystals, and breakage behaviors were studied. The studied cases revealed that these material interfaces control the micropore properties that play a vital role in the initiation of intergranular and intercrystalline fractures which occur in siliceous manganese ores and dolomite as a result of thermal treatment. In contrast, banded hematite jasper and coal exhibited a much more complex fracture pattern due to their coherent interfaces and finer physical associations. This study explains the effect of the various types of interfaces on milling, and the approach can be helpful in developing a methodology to enhance mineral liberation with minimum energy consumption.IntroductionComminution is a vital unit operation in the mineralprocessing, cement-making, power-generation and pharmaceutical industries. Its importance in mineral beneficiation operations is increasing every year as a result of the growing need to exploit lower-grade ore bodies and process reject materials (Blazy et al., 1994; DOE, 2005). Low-grade ores require significant energy during grinding to liberate the valuable minerals, which are further separated from the gangues by various beneficiation methods. Various attempts have been made to enhance mineral liberation during grinding to minimize energy consumption. Most of these studies focused on the analyses of the compression mechanism, chemical additives, thermal treatment, microwave treatment and electric disintegration (Klimpel and Austin, 1982; Norgate and Weller, 1994; Bearman et al., 1997; Kumar et al., 2010; Wang et al., 2011; Singh et al., 2012). However, many of these efforts had limited success, and there is a need to see the problem from a fresh perspective."

Jan 1, 2015

By L. H. McGuire

Many coal beds in the State of Washington, pitching as much as 90°, offer unusual mining conditions. This paper describes methods and safe practices of mechanized mining in pitching bituminous-coal beds that have attracted the attention of mining people from most of the coal-producing countries of the world. The development and use of continuous miners as part of the mechanized program apply particularly to the Roslyn-Cle Elum coalfield, Kittitas County, Wash. All three mines now operating in the field use continuous miners and during 1957 furnished 72 percent of the State's total coal production. Mining operations are now conducted in three coal beds of the Roslyn-Cle Elum field. The coal measures range from 3-1/2 to 20 feet in thickness and vary in dip from 5° to 45° in the localities where the coal is mined. Some safety measures adopted by-the principal operating company in the field during the past 30 years of mechanized mining follow: Use of only permissible electrical or compressed-air-operated equipment on other than intake air; providing and using an explosion gallery to test repaired permissible electrical equipment before taking it underground; use of only compressed-air-operated drill augers in preference to permissible

Jan 1, 1959

By Frank J. Skudrzyk, Vladimir F. Petrov

In compliance with the current Russian environmental legis­lation, possible impact of industrial activities on the environment is restricted by acceptable limiting values (maximal allowable concentrations - MAC) of individual chemical substances in the natural environment - water, atmospheric air and soils. These norms have federal status and are valid for the whole territory of Russia. Disposal of the substances, for which no MAC is estab­lished, is forbidden by the law. Many gold mining companies use cyanide in precious metal recovery. This paper overviews the Russian experience in pro­tection of natural water reservoirs from technogenic impact of cyanic technologies. Major toxic compounds, contained in liquid and solid rejects from hydrometallurgical treatment of gold ore using cyanidation, are cyanides (CN), thiocyanates (SCN) and cyanide metal com­plexes. Unlike western classification of various cyanide types, in Russia any inorganic cyanide compounds (simple and in com­plexes with metals), with the exception of iron cyanide com­plexes, are considered toxic and the acceptable limiting value is established for them. MAC is 0.05 mg/I for fish reservoirs and 0.1 mg/I for drinking water. For iron cyanide complexes MAC is 0.15 mg/I for fish reservoirs and 0.25 mg/I for drinking water. Russian norms for thiocyanates are practically as rigid - the acceptable limiting value for them in fish reservoirs is at the level of 0.07mg/l (0.15 mg/I for potassium thiocyanate) and for drinking water - O. lmg/1. Norms for metals are established on the basis of total content regardless of the form in which they are present in water - as cations or complex ions. It should be noted, that in case several toxic compounds of the same limiting value (for cyanides, thiocyanates and base metals the limiting value is toxicological) are present in water. Their allowable concentra­tion is calculated as the sum of actual concentration of each com­pound, divided by the corresponding acceptable limiting value, with the result not to exceed one (compounding effect). Differences in cyanide classification and the necessity to include thiocyanates dictate different analytical methods. This, in a number of cases, results in certain discrepancies in analytical results. Until recently chlorination was used as a basic process of detox­ification of wastewaters. Calcium hypochlorite powder or hypochlorite pulp, prepared of lime milk and chlorine shipped to the plant, were used as a reagent. Chlorination is an efficient method: it allows to completely destroy plain and complex cyanide, in addition to iron complexes, and thiocyanates. A good example of high efficiency chlorination can be found at the Mnogovershinniy mill near the Okhotsk Sea located in the salmon spawning area, for which we designed an automated chlorination plant for tailings dam. Since plant start-up ten years ago, the required concentrations of cyanides and thiocyanates have been kept at the MAC level required by environmental regulatory agen­cies and no harmful affects on ichthyofauna has been reported. One major drawback of chlorination is high cost of the major reagent, as well as secondary contamination of detoxified waters by chlorides. Secondary contamination by chlorides becomes obvious in the course of detoxification of wastewaters of com­plex composition, which require increased reagent consumption. Recent changes in economic conditions in Russia caused the necessity to direct efforts to reduce the costs of precious metals recovery, and in particular, wastewater treatment. We have con­ducted certain work in this direction and obtained positive results. We hope that our experience described below will be of interest to other specialists particularly taking into account the current low gold prices.

Jan 1, 1998

By Jerry C. Tien

The rare earth elements (REEs) are a group of 17 chemical (metallic) elements which appear in the periodic table. The group consists of 15 lanthanide elements along with yttrium and scandium (Table 1). They share many similar properties, which is why they occur together in geological deposits. Although commonly referred to as rare, they are really quite common; the reason they are perceived as rare is because it is not common to find them in commercially viable concentrations. These metals are critical to advanced technology, ranging from smart phones to global positions system (GPS) receivers, medical devices and jet engines. They are critical in green, high-tech and defense industries (Fig.1 and 2). Although there have been increasing efforts to find alternative supplies, these efforts have been complicated by the pollution that rare earth mining and processing creates. To extract rare earths minerals from mined ore is a complicated and costly process. The ore is first mined through normal mining process, the bastnaesite, which generally contains a number of minerals of little value, is first removed through a floatation process. The bastnaesite containing the REEs is further separated into their respective pure forms in a separation plant using acid and various solvent extraction separation steps. Each element has its own unique extraction steps and chemical processes. At times, these elements, in the form of oxides, will require reprocessing to achieve ideal purity. The last steps would be to further process into metals first, then alloys for various applications. The entire process takes approximately 10 days. The mining and processing of REEs, if not carefully controlled, can create environmental hazards. This is one of the reasons the Mountain Pass Mine in California was closed down in the 1980s.

Dec 1, 2013

By T. G. Rozgonyi

The basic goal of this investigation was to determine the degree of drying of high moisture lignite through the use of high temperature and pressure steam autoclaves. Specific items studied were: a) the effect of lignite particle size, b) steam temperature and pressure required, and c) the time of ahydration. Although removal of sodium, ash, sulfur and other ash-forming minerals was not the goal of this study, basic analysis of effluent water showed organic material and alkalai metal content. Removal of inherent moisture from run-of-mine lignite was tested by lock-feeding the lignite, which was previously sized by screening into 25 kg autoclaves. High pressure, up to 4.053 MPa (588 psi), saturated steam was then introduced into the pressure reactor. Reaction time, pressure, temperature, and depressurization rates were strictly controlled for each reactor test run. Results indicate that about 80% of lignite total moisture was removed, including some of the inherent moisture, yielding a non-oxidized, and thus stable, lignite product. As stated, a side benefit occurred as some reduction of non-combustible portions of the lignite also took place. The conclusion reached as a result of the tests is that the steam-drying process can be successfully applied to reducing moisture in lignite, and may be considered for additional studies on acceleration of the coalification process. On the basis of the data presented, the author believes that lignite can be economically upgraded in steam autoclaves by simultaneously reducing the moisture content by 80 percent and the sulfur content by at least 50 percent. Upgrading the lignite by this method will result in large energy and financial savings.

Jan 1, 1984

By P. Kawahata

Newmont?s Twin Creeks Mine, located in northern Nevada, is producing gold ore from surface mining operations. The ore is currently processed at three different on-site facilities depending on ore type and grade. Processing facilities operate under stringent geochemical blending constraints that must be met from mine ore deliveries and off-site sourced ore. To analyze various strategic options, the technical team utilizes the mathematical optimization approach. However, due to the size and complexity of the operation, there are unique challenges in optimizing life-of-mine production scheduling. This paper describes those challenges and methods developed to take advantage of different scheduling software to effectively compensate each other and result in reasonable guidance. This paper also describes how those scheduling results are reflected in detailed mine plan and cost estimate work.

Jun 1, 2013

By H. Maleki

This paper recognizes the 100th year of research accomplishments by the mining industry resulting from close cooperation among mining companies, geotechnical consultants and researchers from the former United States Bureau of Mines in stability assessments and development of improved and productive mine designs. The paper provides an overview of dramatic developments in geotechnical instrumentation, and its applications in the U.S. and around the world for enhancing the understanding of ground response to mining-induced changes in stress, resulting in improvements in ground control technologies.

Jan 1, 2010

By H. T. Mikkelsen

Mineral production implies emissions of particulate matter (dust), noise and vibration that may cause conflicts with neighbors living nearby. In Norway a few conflicts has been brought to court, the latest in 2006. This paper discusses dust emissions and dust depositions (dustfall). The pollution authorities have accepted monitoring of dustfall instead of suspended dust as the first step in conflict cases concerning small and medium sized enterprises. In the case of exceeded limit values, the second step is to require monitoring of suspended dust and next the implementation of control actions to reduce dust emissions. Dustfall monitoring programmes carried out at six mineral production plants in Norway, show that the mineralogical rates of dustfall are rather low a few hundred meters away from the plants or the tailings disposal. They are mostly considerable lower than the limit value of 5 g/m²/30days accepted by the authorities. Seasonal variations between mineralogical and organic dust fractions can be observed in Norway, with higher content of mineral dust during winter time. Other sources to mineralogical dust can be recognized. During winter time wear of road pavement and sand on icy roads can give high emissions of mineralogical dust to the ambient air. Parallel monitoring of suspended dust and rates of dustfall indicate that dustfall can be used to estimate the level of suspended dust. A model for estimating suspended dust based on records of dustfall is presented.

Jan 1, 2007

By Aleksandar N. Nikoloski, Rorie Gilligan

Brannerite, UTi2O6, is the most common of the refractory uranium minerals and requires leaching under intense conditions to effectively extract the uranium contained within. Brannerite is often found together with apatite in metasomatic uranium deposits. Apatite and other phosphate gangue minerals can inhibit uranium leaching by generating phosphate ions which interfere with the reactions between acidic ferric sulphate and uranium minerals. As part of a detailed fundamental study on the leaching reaction mechanisms for brannerite, tests under a range of selected leach conditions were carried out with the addition of 10 g/L fluorapatite with the goal of identifying conditions where the negative effects of phosphate are reduced. Leaching was carried out for 5 hours with 0.05 mol/L Fe3+ as Fe2(SO4)3 with 0.25–1.00 mol/L H2SO4 and at temperatures between 25 and 96 °C. A single test was performed with 0.05 mol/L Fe3+ as FeCl3 and 1.00 mol/L HCl. In the sulphate system, the effect of phosphate was weakest at the highest acid concentration (1.00 mol/L H2SO4). In the chloride system, phosphate did not suppress uranium extraction, suggesting that HCl leaching could be a viable alternative for the leaching of high-phosphate refractory uranium ores.

Mar 17, 2021

By J. F. Hunt

[THE AUTHOR DESCRIBES THE ACTUAL PROCESSING OF THE GOVERNMENT STOCK¬PILE OF CHROMIFEROUS SANDS. LOCATED AT COQUILLE. OREGON, DURING 1955 AND 1956. A GENERAL HISTORY OF THE STOCKPILE IS GIVEN, ALONG WITH A BACKGROUND OF THE GEOLOGY AND ORIGIN OF THESE SANDS. THE FLOW SHEET USED IN THIS OPERAT ION IS OUTLINED IN DETAIL, AND THE MINERALS WON FROM THE STOCKPILE BY HIGH TENSION AND MAGNETIC PROCESSING ARE DISCUSSED AS TO THEIR PURITY AND SALEABILITY. AMONG THESE MINERALS ARE CHROMITE, ILMENITE, MAGNETITE, ZIRCON, GARNET, RUTILE, MONAZITE, GOLD, AND PLATINUM. PLANNED POST-STOCKPILE OPERATIONS ON THE PRESENT BEACH DEPOSITS ARE DISCUSSED. THESE OPERATIONS WOULD HAVE BEEN CARRIEDOUT TO SET UP A' CONTINUOUS INTEGRATED MINING AND BENEFICIATION PROJECT, EXCEPT FOR UNFORESEEN CIRCUMSTANCES WHICH DICTATED THE CLOSING OF THE OPERTIONS AT THE EXHAUSTION OF THE GOVERNMENT STOCKPILE. THE PAPER IS ILLUSTRATED WITH MAPS, FLOW SHEETS, CHARTS; AND PHOTOGRAPHS OF STOCKPILE, PLANT, AND EQUIPMENT.]

Jan 1, 1964

By Sean Dessureault

The mining industry has used fleet management systems (FMSs) for decades. These systems were developed long ago in large truck-and-shovel mines, where hardware sales were the core business driver for vendors. These traditional models can be overhauled in the era of the Internet of Things (IoT), Big Data, gamification and low-cost tablet technology. Relatively low-cost tablets are ubiquitous in modern life, and they are packed with communication radios and sensors like Global Positioning System (GPS) and inertial measurement units used widely for games, fitness measures and navigation. These powerful computer devices provide the same, if not more, sensing capability than traditional fleet management hardware, all at a fraction of the cost and without complicated cables or challenging supply lines. 

By J. P. Earnhardt

Recycling of such municipal solid wastes as glass containers, metal cans, and newspapers has received increasing attention recently. However, municipal solid wastes account for only 1% of the total solid waste stream in the United States. The remainder includes hazardous and non-hazardous industrial wastes. Generators of industrial wastes are facing higher landfill costs. Future liability potential, and public image concerns which are forcing them to seek innovative and often profitable solutions to minimize, reuse, and recycle their waste streams. Opportunities for the mining industry in industrial recycling include recovery of mining wastes and by-products, and utilization of mineral products for treating waste streams.

Jan 1, 1993

By Matias Pentinnen, Wayne Dickinson

Electrowinning is a key process for copper production contributing roughly twenty percent globally and thirty to forty percent of production in the Americas1. Copper grade is assessed largely on deposit smoothness and on level of impurities in the metal. Smoothing aids are essential to create dense, low porosity deposits and guar has long been the material of choice for this purpose. Guar is, however, poorly stable under the strongly acidic electrowinning conditions, underlying ongoing research to identify an effective, acid-tolerant replacement. Current efficiency is also a critical factor in controlling copper production costs and chemical additives should ideally improve current efficiency as well as improving deposit smoothness.

Feb 1, 2025

By D. L. McClure

Gold mineralization at the Colosseum Mine is submicroscopic and associated with pyrite. Pyrite occurs in breccia clasts, replacing dolomite, in crackle breccia veinlets with traces of quartz, and as disseminations in two small, interconnected intrusive pipe complexes of rhyolitic felsite and breccias of felsite and wall/country rock. Breccia types grade from felsite plus wall rock of Pre-cambrian gneiss to cross-cutting breccias "of felsite, gneiss, and Paleozoic sedimentary rocks that are in contact with the Precambrian gneiss terrane one-quarter mile (40Om) southwest of the Colosseum pipes. Mineable reserves are estimated to be 8 million short tons (7.3 million metric tons) at 0.074 troy ounces of gold per short ton (2.3 g/metric ton) at a cutoff of 0.03 troy ounces of gold per short ton (1.0 g/metric ton).

Jan 1, 1988

By John S. Lagarias

When ore bodies are faulted or mill feed turns refractory, mining managers and engineers act vigorously to convert imminent failure into eventual success. The recent proliferation of onerous "environmental" regulations and restraints is likewise a threat to successful mining enterprise, in some ways more insidious and dangerous than the problems presented by natural obstacles. The regulatory burden has become so heavy that a pall of pessimism covers much of the mining enterprise. In this paper we frankly recommend a Pollyanna approach, making not just "the best of it" but directing the whole environmental process: first, to improve our planning, engineering, and operating procedures; and, second, to demonstrate the need for modification of laws and regulations which are intolerably burden-some to both the mining industry and the public. It is customary for government officials and environmentalists to point out how great are the new environmental regulations and how successfully these have improved the natural environment in particular and the quality of life in general.

Jan 1, 1978