Search Documents

By Y. C. Lo

This paper attempts to answer whether or not the mill performance at Bougainville could have, in fact, been predicted by the population balance approach, or whether other special considerations are required to explain their behavior. In recent studies, the plant tests were performed at Bougainville and batch tests were carried out at the Utah Comninution Center. In all tests power measurements were made and several levels of energy input to grinding were evaluated. Also, tracer tests were performed for mill residence time determination. The performance of Bougainville's 5.5 x 6.4 m mill has been very successfully predicted by population balance methods. The prediction errors are only about 1% on product size distribution and 4% on power with a mill volume scale-up of 3790 to 1. It is significant that this approach will reduce the risk of failure in large mill design that has been recognized in traditional methods.

Jan 1, 1987

By M. M. Fine

One of the most persistent topics at technical gatherings and in the recent scientific press has been the reduction of iron ore. To cite some of them, in May 1960, a symposium on the subject was sponsored by the Electrochemical Society. The proceedings, comprising two dozen papers, were later published.3/ More recently, November 1966, a similar gathering took place at Michigan Technological University, Houghton, Mich. The latest meeting was the International Congress on Production and Utilization of Reduced Materials, Evian, France, May 1967. If the volume of literature, symposia and conferences is a measure of industry concern, then current interest must be at a high level. To the casual observer of the metallurgical scene, the abiding and recurring attention to iron ore reduction outside the blast furnace must be somewhat puzzling in that so much research endeavor has resulted in so little commercial activity.

Jan 1, 1968

By D. L. Ealy

At the Beckley Mine in southern West Virginia, forecasting unstable roof conditions in advance of mining is accomplished by using a rating system that combines historical information on mine roof failures with known mine geology. Failure frequency rates are derived for each category of roof rock composition, unit thickness, structure, and extraction ratio. In this manner, known geological environments are rated according to instability based on actual experience. Drill hole control and geological interpretation provide the basis for forecasting unstable conditions beyond working faces. The forecasting technique has assisted mine management in reducing fall frequencies by 80% over the past two years compared to the first five years of operation. This reduction in fall frequency was accomplished by modifying the plan of advancing sections to minimize mining exposure to unstable roof conditions.

Jan 1, 1980

By T. N. Moore, E. M. De Souza

J. Dasher Regarding the March 1991 ME technical paper by De Souza and Moore: For more than a decade since my February 1981 article on how to use modern metric, which SME-AIME had decided to do, I have monthly pointed out metric errors to the editors. In part, I do this because there has been no action to allow editors to fix figures and tables or to allow them to require authors to do so. The latest resulting atrocity provokes this discussion of vibrating drill handle units being stated in decibels. Reply by T. Moore We have read the discussion of our paper by Mr. Dasher. Our reaction is one of surprise and incredulity. It would seem that Mr. Dasher takes exception to the use of the decibel scale to present vibration acceleration data, and the use of hertz as the unit for frequency. The basis for his objection to the decibel appears to be that it has no dimensions (which somehow invalidates its use), that it is "non-metric" and, finally, that it is parochial (of limited or narrow scope). His objection to the use of the term hertz is not stated, but we will assume that it stands condemned as "non-metric" and parochial. Obviously we disagree with Mr. Dasher's views and will now outline our reasons. Although the decibel scale originates from transmission line theory and telephone engineering, it is also at present widely used, not only in the fields of electronic engineering and acoustics, but also in the area of vibration. The original definition of the decibel (dB) was based on power ratios: dB = 10 log 10(W/W0) where Wo is a reference power. However, as the power measured across a given impedance is related to the square of the force acting upon this impedance, Z, a more commonly used definition is: [2 dB = 10 logF /Z) = 20 log F/F 10\ F0 2 /Z(0)] where F and F0 are the r.m.s. values of the forces. Now, if the measurements are related to one and the same impedance, the decibel notation in the form of 20log10(X/Xo) may be used as a convenient relative magnitude scale for a variety of quantities. Thus, X may, for instance, be an r.m.s. displacement, velocity or acceleration. It is only required that XD always be a reference quantity of the same type as X. That is, when X represents an acceleration, then X0 represents a reference acceleration. This is the formulation used in our paper. This was not an arbitrary choice on our behalf but reflects standard practice as specified in the International Standard ISO 5349-1986(E) Mechanical Vibration - Guidelines for the Measurement and the Assessment of Human Despite the metric prefix, the decibel is a parochial expression of (l) the logarithmic ratio of the loudness of a sound to what is normally audible or (2) the logarithmic ratio of two power signals in radio or electronics. A decibel is not a unit, much less an SI, unit and has nothing whatsoever to do with the acceleration of drill handles. Stating that m/s2 (acceleration) is decibels is without reason. Whoever reviewed this material should not have allowed publication of figures of dB and H.[ ] Exposure to Hand-Transmitted Vibration. This was clearly stated in the "measurement protocol" section of our paper. This quantity is then referred to as the acceleration level and is expressed in dB. We may have inadvertently caused some confusion when we simply used the term acceleration to refer to acceleration level on our diagrams. At the time, we felt the use of dB or m/s2 would make the context clear to the reader. For any confusion this decision may have engendered, we apologize. Since the decibel expresses the ratio of two like quantities, it certainly has no dimensions. It is, however, common practice to treat "decibel" as a unit as, for example, in the sentence, "The acceleration level measured at the operator's hand was 160 dB." The expression of measured quantities in dimensionless form is not inherently unacceptable. In fact, in many areas of engineering it is standard practice (consider the use of Reynolds Number, Nusselt Number, etc.). The fact that the decibel is a dimensionless quantity makes the question of whether it is a SI unit nonsensical. However, it is valid to insist that the dimensional quantities used to obtain the decibel values be expressed in SI units. A careful reading of our paper will make it clear that the measured acceleration was, in fact, expressed in units of m/s2 as was the reference acceleration (l x 10-6 m/S2). These are the accepted derived SI units for acceleration. See, for example, the standard ASTM E380-89a Standard Practice for Use of the International System of Units (SI) (The Modernized Metric System). Concerning Mr. Dasher's implication that hertz (Hz) is an unacceptable unit of measure for frequency, we would again refer him to the standard ASTM E380-89a. Here, he will find (section 2.4.2) that hertz is an accepted "special name" for the derived SI units-1. This is in keeping with numerous other international standards including ISO 5349-1986(E) to which we referred in our paper. In conclusion, we agree with Mr. Dasher on the desirability of expressing measurements in modern SI units. But we would remind him that the standards that define the use of these units, and the accepted means of presenting measured data, are in a continual state of refinement. It is, therefore, incumbent upon him to keep abreast of these changes if he wishes to constructively critique the work of others.[ ]

Jan 1, 1992

By Charles E. Dunne

One of the most frequently asked quesitons is: "Where is copper (price and usage) going?" I will not attempt to forecast either the future price of copper or the future growth of the copper industry; rather I would like to discuss the current trends experienced in the smelting and refining terms and conditions for sales and/or purchases of copper concentrates. A brief review of contract language and terms, together with a review of the common jargon, I believe, would be helpful. To accomplish this review, I will first list what I consider the four basic parts or sections of a basic ore contract and then illustrate basic terms with calculations.

Jan 1, 1984

By Richard L. Ash

Usually stresses generated by explosive charges during blasting are considered to propagate through materials in a spherical manner. Although conical stress-waves had been suggested by a few investigators they have never been clearly defined or critically observed. An experimental technique using models and lengths of Mild Detonating Fuse was developed to produce conical stress-waves and study their effects. Several materials with different properties were tested to compare the influence of those properties on wave shape and crater formation. The investigations showed that whenever column charges were end-initiated, conical stress-forms were produced if the explosive's velocity exceeded the energy propagation velocity of the surrounding material. The stress-cone angle significantly affected fragment size and shape as well as the geometry of craters produced.

Jan 1, 1967

By R. A. Cummings

From before the turn of the century until as recently as the 1950s, relatively shallow coal reserves near the margins of the Illinois Basin were extracted by room- and pillar methods. Subsequent development has, in many cases, extended onto ground with high subsidence potential. The same state of affairs exists in many other historical coal mining districts, as well as in Illinois. Pit subsidence in Illinois is particularly common in the towns of Streator, Carterville, and Herrin, although there are others. Pit subsidence is characterized by distinct circular or oval depressions and normally is associated with shallow mining and thick soil relative to the thickness of rock.

Jan 1, 1985

By Robert W. Bruhn

Ground movements associated with high extraction underground coal mining, such as pillar retreat and longwall, are sometimes large enough to disrupt the ground water regime as well as damage buildings and other surface structures. A U.S. Department of Energy/Bureau of Mines- sponsored subsidence study currently underway at Kitt Energy Corporation's Kitt No. 1 Mine near Philippi (Barbour County), West Virginia has provided an opportunity to monitor the ground water response above a mine panel during both developmental and pillar retreat mining. The initial findings concerning ground water effects presented in this paper indicate that total extraction mining produced significant water level declines in deep-lying strata but had little effect on water bevels at shallower depths.

Jan 1, 1985

By Charles Kimbell, L. Nahai, E. Shekarchi

INTRODUCTION AND SUMMARY World mineral trade during 1960 to 1984 has shown substantial changes both in value and tonnage. Although fuel commodities dominated total mineral trade during this period, this paper will focus attention primarily on nonfuel minerals. Brazil and Australia, modest producers of iron ore in 1960, have become dominant producers and exporters, together accounting for about half of major iron ore exports in 1984, far surpassing traditional export suppliers such as Sweden. Australia has also become the largest producer and trader of bauxite and alumina, and worldwide alumina trade has increased at the expense of bauxite trade. Similarly, shipments of ferroalloys have increased more than shipments of ores such as those of chromium and manganese. Canada, retaining its first rank in world export of zinc, has become also the leading source of potash and sulfur in world trade, and South Africa has been the dominant factor in chromite, manganese and their respective ferroalloys. Developing countries' share of world copper trade has increased, with Chile maintaining first rank, but developed industrialized countries have continued to dominate production and trade of lead and zinc. Phosphate, sulfur, and potash have been the principal crude nonmetallic minerals traded worldwide. Looking to the near future, dramatic increases in export of iron ore, phosphate, potash and sulfur are not envisaged. Bauxite exports will continue to decline relative to alumina but at a slower rate than in the recent past. Zinc concentrate will continue to be exported but lead will be traded more as metal than as concentrate. For iron and steel, there will be some production shift from traditional producers to certain developing countries and recently industrializing developing countries such as Brazil, India, the Republic of Korea, and Taiwan. In the following sections dealing with specific commodities, it should be understood that information is presented only on the major forms of each commodity that move in trade, and only for a selected group of countries for each commodity or major form of each commodity. Thus, totals shown or mentioned generally represent only the totals of figures presented here and do not include estimates for minor forms of material or for countries that are not listed. However, the data provided is regarded as sufficiently complete to reflect major patterns and trends, and exclusions are there- fore not seen as affecting conclusions that may be drawn from the material provided. FUEL AND NONFUEL TRADE Values of Fuel and Nonfuel Trade The value of world export trade in major mineral commodities (ores, concentrates and scrap, crude minerals, iron and steel, nonferrous metals, nonmetallic minerals and mineral fuels) in 1983, the latest year for which comprehensive data are available, was reported by the United Nations in May 1985 to have totaled over 514 billion current U.S. dollars (Table 1). This was 79% of the historic record high of nearly $649 billion ,current dollars set in 1980, but almost 18 times the current dollar value reported for 1960. [1/] The value of these 1983 exports in constant 1960 dollars was $164 billion (Table 2), only 66% of the record 1980 high of almost $250 billion, and only about 5.7 times the 1960 dollar level.

Jan 1, 1986

By W. R. Reed, G. J. Joy, B. Kendall, A. Bailey

"Testing of the roof bolter canopy air curtain (CAC) designed by the U.S. National Institute for Occupational Safety and Health (NIOSH) has gone through many iterations, demonstrating successful dust control performance under controlled laboratory conditions. J.H. Fletcher & Co., an original equipment manufacturer of mining equipment, further developed the concept by incorporating it into the design of its roof bolting machines. In the present work, laboratory testing was conducted, showing dust control efficiencies ranging from 17.2 to 24.5 percent. Subsequent computational fluid dynamics (CFD) analysis revealed limitations in the design, and a potential improvement was analyzed and recommended. As a result, a new CAC design is being developed, incorporating the results of the testing and CFD analysis.IntroductionExposure to respirable coal mine dust can cause coal workers’ pneumo-coniosis (CWP), also known as black lung. If silica is present in the dust, the miner may develop silicosis in addition to CWP. CWP and silicosis are occupational respiratory diseases that are ultimately fatal and have no cure. The only method of prevention is to eliminate exposure to respirable coal mine dust and crystalline silica, or quartz. The occupational exposure limit on a Mining Research Establishment (MRE) basis for respirable coal mine dust had been 2 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities. Under recently enacted legislation, this standard was changed in August 2016 to 1.5 mg/m3 for a full working shift (The Office of the Federal Register, 30 CFR 70.100, 2015). When respirable quartz is present, the mine must maintain its average concentration at or below 0.1 mg/m3. If the mine exceeds the 0.1 mg/m3 respirable quartz dust concentration, then the applicable respirable dust standard is reduced, calculated as 10 divided by the percentage of quartz present (The Office of the Federal Register, 30 CFR 70.101, 2015).The sources of exposure to respirable coal mine dust for roof bolting occupations include infrequent maintenance and cleaning of the vacuum dust collection system and operating the bolter downwind — in the return air — of the continuous miner (Good-man and Organiscak, 2003). Recent studies have demonstrated that vacu-um dust collection systems are effective in capturing bolter-generated dust if maintained and operated correctly and if proper face ventilation techniques are used. However, most expo-sure to respirable coal mine dust for a roof bolter occurs when the roof bolter machine is operated downwind of the continuous miner (Potts, Reed and Colinet, 2011; Colinet, Reed and Potts, 2013). Because of this higher exposure downwind of the continuous miner, the roof bolter is often limited to working downwind of the miner only once during a production shift."

Jan 1, 2017

By V. O. Tenorio, K. W. B. Requist

As the mining industry begins efforts to examine the feasibility of extraterrestrial resource utilization, the extraction and processing of icy regolith containing water and other volatile materials will be the initial focus for future expansion of capabilities. Pure water is essential for human consumption, and a source of oxygen and hydrogen. The latter, along with the volatile materials, lend themselves to the creation of fuels that may be used for further space exploration at distances not currently feasible. For any extraterrestrial scoping project, the transport of materials to geoscientists remains virtually impossible. Therefore, analysis must be done in-situ, possibly millions of miles away from the nearest human. To address the need for geologic resource estimation in the absence of geoscientists, an infrared framework has been developed for the analysis of water ice content in simulants of permanently shaded lunar regolith. This framework relies on a convolutional neural network model for the rapid analysis of percent water ice content in samples, at which point standard geostatistical methods may be employed.

Feb 1, 2023

By Robert L. Frantz

The various facets of university-company cooperative activities and the opportunities for collaborative research for the mineral industries are presented in this paper. The advantages and disadvantages of various alternative research funding arrangements for the researcher, the university, and the sponsoring corporation are discussed. Examples of university-industry cooperative research programs are briefly outlined. The concept of a cooperative mining research program is presented. The improvement of performance through techno- logical developments and human skills may well be the greatest competitive edge available to the U.S. mining industry. In this regard, the need for new endeavors between industry and universities can hardly be overemphasized.

Jan 1, 1984

By M. W. Buche, E. Tarshizi, R. Chappidi, B. Inti

"Coal mining is an age-old method of power production in the world. It is also widely known for the associated risks during mining. Although the number of mishaps has dropped dramatically over the years, the number of fatal accidents is still a concern, and any aid in reducing these figures would be important to industry workers. Therefore, data from accident reports during the past seven years were collected and analyzed. Qualitative data from reports and articles provide a deeper understanding of the incidents, thus affording the possibility of identifying patterns and relationships between the accidents. For this study, a total of 119 fatality accidents occurring in U.S. coal mining operations were analyzed using advanced text mining techniques. The fatality data were obtained from U.S. Mine Safety and Health Admininstration fatalgram reports. This analysis is primarily exploratory in nature and uses term frequencyinverse document frequency (TF-IDF) methodologies along with correlation network plots. An interesting word relation pattern was obtained that identified “positioning” as the common cause of 12.6 percent of accidents, and found that 29.4 percent of accidents can be categorized as vehicle-related. IntroductionIn the mining industry, accidents are situations that employees and employers wish to avoid. They are devastating experiences to the victims and their coworkers alike. Even worse, accidents that result in fatalities create trauma and undesirable repercussions. Several measures have been taken throughout the industry to prevent such mishaps, and the U.S. Mine Safety and Health Administration (MSHA) provides continuous monitoring for miners’ safety by guiding organizations through best practices in every job role. As a result, according to MSHA, there has been a steady decline in the average number of deaths due to accidents over time. Nonetheless, any opportunity to avert one more such casualty is of paramount importance, and that is the goal of our analysis. Our objective is to identify opportunities resulting from previously unexplored directions in order to provide additional insights into potential safety recommendations. Until now, most of the studies in this area had been conducted using structured and tabulated data with a constant number of categorical and numerical variables. Unstructured text data mining is an emerging area that is still insufficiently researched and has a feasible scope for important results, as a vast majority of human communication and cognizance is comprised of words. The aim of undertaking this project by capitalizing on unstructured data is to analyze the text reports to discover potential relationships that explain the causes of accidents in new light in order to mitigate the occurrence of fatalities. The analysis in this project is based on textual data obtained from the MSHA website (2017). Individual accident reports are organized according to the date and year of the fatality. Each report includes details with images of the incident. For convenience, a simplified summary of the report is also available. Data collection consisted of gathering formal documentation of fatal accidents in the coal mining industry during the past seven years. These reports were extracted from the website in text format."

Jan 4, 2018

By S. S. Klima, D. E. Pollock, J. A. Organiscak

"Airborne respirable coal dust capture by water sprays or wet scrubbers has been studied and developed over many decades as an engineering control to reduce dust exposure in coal mines and combat coal worker pneumoconiosis. Empirical relationships and deterministic models for particular dust capture experiments have previously been devised to show the key parameters involved in airborne coal dust capture. Many of the results from these models show that the significant parameters related to airborne dust capture are water spray pressure, water quantity, water droplet size, relative water droplet-to-dust particle velocity, and total operating air pressure of the scrubber. However, many airborne dust capture efficiency relationships and models developed for particular experiments cannot be readily applied to forecast the dust collection efficiency of different spray and scrubber design configurations, which rely on several key dimensional engineering measures. This study examines engineering measures from previous water spray and wet scrubber experiments conducted by the U.S. National Institute for Occupational Safety and Health (NIOSH) and the U.S. Bureau of Mines (USBM) to develop empirical models for wet collection of airborne dusts. A dimensionless empirical model developed for predicting airborne dust capture efficiency of water sprays and wet scrubbers is presented. IntroductionWater sprays have been one of the earliest mainstay engineering controls used to suppress respirable dust in underground coal mines. Some of the earliest reports of water spray usage on continuous mining machines indicated respirable coal mine dust reductions of 20 to 60 percent (Kobrick, 1970). Not long after the enactment of the 1969 Coal Mine Health and Safety Act, the U.S. Bureau of Mines (USBM) and others conducted extensive research into water spray and wet scrubber systems to control respirable dust in coal mines. The primary aspects of water spray dust control included prewetting for dust prevention, localized ventilation redirection and airborne dust capture, which are summarized in handbooks or best-practices guides (Kost, Yingling and Mondics, 1981; Kissell, 2003; Colinet et al., 2010). Initially, underground studies were conducted to identify the primary sources of dust during the mining processes and effective dust controls (Courtney, Jayaraman and Behum, 1978; Jankowski and Organiscak, 1983). Laboratory research systematically studied ventilation and airborne dust capture effects of water sprays and scrubbers to improve their application in underground coal mines (Tomb, Emmerling and Kellner, 1972; Divers and Janosik, 1978, 1980; Grigal et al., 1982; Ruggieri et al., 1983; Jayaraman, Jankowski and Kissell, 1985; Volkwein, Ruggieri et al., 1985; Jayaraman, Schroeder and Kissell, 1986; Divers, Jankowski and Kelly, 1987; Jones and James, 1987)."

Jan 10, 2018

The purpose of this paper is to present validation studies of the mine-fire simulator using data gathered from an actual mine fire which occurred in November 1991 at the Pattiki Mine. To develop the model of the ventilation system with the fire in this validation study, the following adjustments were made: (1) flow and gas distribution in the entire ventilation network, and (2) fire parameters matching the data recorded by the monitoring system. After close correlations between simulation and real data were achieved, additional analysis of the ventilation system with the mine fire was performed. Presented and discussed in this paper are the following stages of the fire at the Pattiki Mine: (1) early fire (before the fire was detected), (2) preparation for and fire fighting with water, (3) fire sealing, and (4) fire extinguishing. This study evaluates the suitability of the computer software package for modeling underground fires. The paper also discusses the importance of the on-line monitoring system for the validation process.

Jan 1, 1995

By Carter Brown, Kate Brown Requist, Eric Lutz, Moe Momayez, Athira Satheesh

New mining health and safety training modalities are becoming increasingly prevalent in the underground mining industry. Various digital training tools have been developed over the past several years, but the extent of their use remains unclear. Advances in gamified training by way of computerbased video games and virtual reality (VR) have opened a new avenue for mine rescue and self-escape training, but these methods have not been widely adopted across the mining industry. Mine rescue and self-escape situations require a mix of in-classroom training as well as live drills, but it is important to assess the extent of and effectiveness of new training modalities. The Mine Rescue and Self-Escape Survey (MRSES) was distributed to underground mining operations to collect perceptions of current training effectiveness as well as willingness to adopt new training methods as a complement to live rescue drills. Responses from the MRSES indicate that adoption of digital training technologies has been slow-going despite an interest in their use. Further, there appears to be no meaningful connection between more frequent escape and rescue training and feelings of emergency preparedness. With relatively little use of already developed digital training tools but an interest in their adoption, it may be time to reassess current emergency preparedness training philosophies.

May 1, 2025

By George M. Anderson

The extraction of industrial minerals is usually confined to relatively small mining operations. The recent COSMAR (Committee on Surface Mining and Reclamation) report found that 93% of all mines in the United States were of the small unit variety. Also, of the total number of mines in the U.S. (15,279) 96% were in the industrial minerals (non-metals excluding coal) category. To break it down further, 86% were sand and gravel, and crushed stone operations. Therefore, we are talking about a very large number of small mining operations. If these small miners can afford to hire a college graduate, what kind of training should this person have beyond the normal mining engineering curriculum to best serve the problems that he or she will encounter?

Jan 1, 1981

By E. B. Thorn

The production of portland cement requires that four basic elements -- calcium, silica, alumina and iron -- be ground to a fine powder, homogenized, and fed to the pyroprocessing unit, where it is burned to a cement clinker. The raw material must either be ground wet in a slurry form or dried and ground to a dry powder, with a fineness of approximately 85% passing the 200 M screen. According to the Portland Association's Plant Information Summary, approximately 38% of the U.S. capacity is ground wet and 62% ground dry. The following data is taken from the Portland Cement Association's 1981 Energy Survey: [Million BTU/Ton kW h/Ton Wet Process Plants 5.86 138 Long Dry Process Plants 4.97 123 Dry Preheater Plants 4.03 157 ]

Jan 1, 1984

By Jacques B. Wertz

It is well known that the major fractures and lineaments presently recorded in Western North America are preferentially oriented along a general northwest direction (Figure 1). There are other features, however, more subtle, more elusive as a rule and which can only be inferred, occurring at right angle to this broad NW direction. It is intended a) to examine some of these NE or transverse trends, b) to compare these regional NE breaks to similar ones that transversally cut through the eastern part of the European Tethys, more specifically in Iran and Turkey, and c) to study their potential relationship to mineralization in both areas.

Jan 1, 1973

By Gary E. Geiger

laboratory studies were performed to assess the calcium carbonate inhibition performance of phsophonates and polymeric dispersants at high hardness and high pH conditions. Based on the results of these studies, a new calcium carbonate treatment program was developed that shows excellent Inhibition characteristics and Is not sensitive to calcium hardness.

Jan 1, 1998