Search Documents

By Hee-Young Chung, In-Mo Lee, Jeongjun Park, Hangseok Choi, Seok-Won Lee

"When using a Tunnel Boring Machine (TBM) during tunneling work, unexpected ground conditions can be encountered that are not predicted in the design stage. These reduce the stability of tunnels, and can result in considerable economic losses. This paper analyzes the potential risk events that may occur due to risky ground conditions. A resistivity survey is utilized to predict the risky ground conditions ahead of the tunnel face during construction. The potential risk events are evaluated considering both the occurrence probability and the impact. A TBM risk management system that can suggest proper solution methods for potential risk events is also developed. Multi-Criterion Decision Making (MCDM) is utilized to determine the optimal solution method to handle risk events. Lastly, an actual construction site, at which a risk event occurred during tunnel construction, is analyzed utilizing the Earth Pressure Balance (EPB) Shield TBM, to verify the efficacy of the proposed system.INTRODUCTION The Tunnel Boring Machine (TBM) method has been widely adopted in numerous tunneling projects because, as a mechanized tunneling method, it is also environmentally friendly, exhibiting minimal noise and vibration when compared with conventional tunneling method. In addition, it provides considerable economic benefits that allow for a high advance rate for long drives during construction. However, the TBM method has a limitation, as it is unable to deal with unexpected situations during construction, as the system is not capable of moving backwards. This leads to delays or even stoppages, and a corresponding increase in construction costs due to the need to arrange for alternative equipment and solutions. It is essential to retain systematic management in order to prevent or deal with unforeseen consequences such as the collapse of a tunnel face, ground surface upheaval or settlement, and construction delay due to water leakage during construction. Therefore, a systematic risk management system that is applicable during the construction stage of the TBM tunnel should be developed, taking into account the predicted risky ground conditions ahead of the tunnel face in advance."

Jan 1, 2016

By M. Board, C. Alexander, M. Ramström, W. Johnson

"Hecla - Lucky Friday is an underground mine that has been in operation for 75 years and produces from depths over 2.3 kilometers (7,500 ft) below the surface. Technical issues at this depth include high rock temperature and seismicity. The use of new innovative mechanization is being examined for ore production. Principal advantages of mechanization are the reduced exposure of personnel, reduced seismic triggers, and increased efficiency. Lucky Friday has partnered with Atlas Copco to design, build, test, and deploy a mechanical miner for primary ore production. We will discuss the background, concept, development and deployment strategy for a mechanical miner. BACKGROUND The Coeur d’Alene mining district in northern Idaho was first discovered over 130 years ago and has been the most prolific silver producer in the US. The Lucky Friday mine of Hecla Mining Company (Figure 1) is the oldest (76 years) and deepest mine in the district, producing approximately 725 tonne per day (800 tons per day) from narrow, vertical lead-zinc-silver veins. Cut and fill stoping is currently employed at depths to about 2.3 km (7,500 ft) below ground surface, making it one of the three deepest mines in the western hemisphere. The #4 Shaft, a winze collared at approximately 1.8 km (5,900 ft) below surface and extending to a depth of nearly 2.9 km (9,600 ft), was recently completed to exploit the high-grade 30 Vein, whose resource has been identified to at least 3 km (9,700 ft) in depth.As with other deep mines worldwide, a number of challenging engineering issues occur, including: high in situ rock stress, squeezing ground, seismicity, high in situ rock temperature that requires refrigeration, diesel equipment that generates diesel particulate matter (DPM) requiring high ventilation airflow rates, and long travel times for worker transport to mining areas."

Jan 1, 2018

By Samuel S. Adams

The Grants uranium region of northwest New Mexico is the largest uranium district in the United States (approximately 50% of U.S. production plus reserves) and one of the largest In the world, with approximately 900 million pounds U308 production plus reserves. Deposits of the region are unusual among sandstone deposits for their high content of epigenetic carbonaceous material, generally interpreted but not proved to be of humic origin--that is, co-extensive with uranium in the primary deposits. Virtually all production in the region has been from the Jackpile Sandstone and Westwater Canyon Member of the Jurassic Morrison Formation. The tabular uranium deposits contain, in addition to humate and uranium, significant authigenic phyllosilicates, quartz overgrowths, humate-replaced detrital silicates, and a trace-metal assemblage typical of other sandstone uranium deposit types. Surrounding the deposits in the two sandstone units of the Morrison Formation is an alteration zone within which iron leaching has altered detrital ilmenite-magnetite to residual masses of titanium oxides. Feldspar alteration is locally present within this zone, below deposits in the Jackpile Sandstone, and above those in the Westwater Canyon Member. The feldspar alteration increases in inten¬sity toward the Brushy Basin Member which separates the two sandstone units, ranging from partial replacement to replacement and dissolution of plagioclase and sanidine. Spatial relations among the epigenetic humate, authigenic silicates, and the broad alteration zones that extend from the Brushy Basin Member to and including the uranium deposits suggest that (a) the organic material was involved in the unusual silicate alteration, transport, and authigenesis, and (b) that the humates originated in shales of the Brushy Basin Member. Stratigraphic relations among the Brushy Basin Member and the overlying Jackpile Sandstone and underlying Westwater Canyon Member suggest [in turn] that there was continuous, interfingering deposition controlled in part by contemporaneous basement subsidence along northwest- and northeast-trending zones. Following minor erosion of upper Jackpile Sandstone and deposition of basal organic-rich Cretaceous sediments, the silicates of the Jackpile Sandstone were once again altered by organic-bearing fluids, this time permeating down from Cretaceous sediments and partly obliterated ore-stage alteration.

Jan 1, 2013

By Gösta W. Diehl

During the past five years the use of all-hydraulic drilling equipment has increased rapidly, and we have now reached a point where the hydraulic drill has become an alternative to be seriously considered for every drilling operation. The hydraulic drills have many advantages over pneumatic drills, but they also have certain characteristics, which makes a potential user hesitate before making the switch. And when the decision to use hydraulic drills has been made, the user then faces another choice of equal difficulty: the choice between different hydraulic systems. This paper discusses some of the factors to be taken into account when considering hydraulic drilling equipment for rapid tunneling in hard to medium hard rock. THE CHOICE BETWEEN HYDRAULIC AND PNEUMATIC EQUIPMENT The choice between a hydraulic and a pneumatic drill is much more than just that: It is a choice between two different systems. The choice is usually based on the productivity, economy or ergonomy of the system. However, also other factors should be considered, such as service capabilities and training requirements. And finally the choice will be influenced by the need to acquire know-how in the new technology. Productivity If the prime consideration is to achieve the highest possible tunneling speed, then the high penetration rates of the hydraulic

Jan 1, 1979

By Alexander I. Feldman, Michael S. Kucker, Robert A. Robinson, Harvey W. Parker

An extensive geotechnical monitoring program was used to assess ground and liner behavior, provide input to a Disputes Review Board, and verify design assumptions during construction of the Mt. Baker Ridge Highway Tunnel along I-90 in Seattle, Washington. The stacked-drift tunnel liner was constructed with twenty-four 2.9 m diameter concrete-filled drifts forming a semi-flexible compression ring, followed by excavation of the 19.4 m diameter soil core. Instrumentation data was used for monitoring hillside stability, liner deflections and loads, impacts on adjacent highway tunnels, for back analyzing soil properties, and for helping to limit construction-induced settlements to about 6 cm.

Jan 1, 1987

By D. J. Torpy

With copper at its host depressed price in several years, producers are looking at every opportunity to cut costs in order to continue operating. Some of the measures that have been applied by different companies include reduction in manpower, high grading, and in some cases partial shutdowns. The most beneficial cost cutting measure implemented by Southern Peru Copper Corporation was to steepen the slope of the final pit limit from a conservative 37 degrees to an average of 48 degrees. By doing so, substantial cash outlays were saved. Southern Peru Copper Corporation (SPCC) operates two open pit copper mines and concentrators in the southern part of Peru, about 150 kilometers from the Chilean bordar. The Toquepala Mine went into production in 1960 and the Cuajone Mine in 1976. Both mines use shovel, truck and train operations. The trains, which haul ore to the crusher or waste to the dumps, are loaded either directly by shovels or by a transfer system. The Toquepala Concentrator treats an average of 43,000 tons per day and the Cuajone Concentrator an average of 55,000 tons per day. Concentrates are shipped via a 200 kilometer railroad to the port city of Ilo where the SPCC smelter is located. The annual production in the smelter from both mines is 290,000 tons of blister copper.

Jan 1, 1987

By J. L. Workman

The stability of spoil and highwall slopes are important to successful strip mining. This paper discusses soil parameters of importance in stability analysis. The common mechanisms of spoil failure are discussed. Modes of highwall failure are also outlined. The importance of water to stability is presented. Dragline mining methods most suited to creating spoil and highwall profiles that address stability needs are provided. It is concluded that groundwater and surface runoff must be well controlled, and that it will often be necessary to modify spoil and highwall configurations to achieve a stable overall slope angle.

Jan 1, 1996

By D. Hong

The leaching behavior of rhenium in ammonium iodide solutions with iodine as oxidant has been studied. Experiments were carried out in an autoclave. The effect of stirring speed, temperature, pH of the solution, iodine and iodide concentrations on the dissolution of rhenium was investigated. It was found that high temperature and high pH of the solutions were essential for the efficient leaching of rhenium. The dissolution rate was found to be dependent upon the concentration of iodine and iodide. It was concluded that the dissolution of rhenium under the conditions studied was controlled by mass transfer of iodine with an apparent activation energy of 15.77 kJ/mole.

Jan 1, 1997

By G. B. Amicucci

A Denver Autometrics Particle Size Monitor, PSM-400, was installed at Golden Sunlight Mines, Inc. in October 1988. The PSM-400 measures the grind product's particle size and percent solids. The particle size is used to control grind size by automatically adjusting mill feed rate. The PSM's continuous response to ore changes has improved grind product uniformity and mill throughput. Metallurgical testing has shown the PSM's accuracy to be +/-1 % + 150 µm (100 mesh).

Jan 1, 1991

By Koji Nakanishi, Masayoshi Karasawa, Yasuhiro Morimoto

"Shin-Yokohama station (tentative name), one of the station of the Sotetsu - Tokyu through line (ST line), is under construction by the OPEN – CUT method. The Underground Soil–Cement Steel Diaphragm Wall is implemented as an earth retaining wall. This earth retaining wall is utilized as a main body of a subway station. It is the first time to utilize this earth retaining wall as the main body. There are two difficult issues for this project. One is that this station is planned under busy major road and there are many underground utilities, for example, an electrical transmission line. Because of that, construction area is limited. The other is that this station is located in a thick soft clay layer. This layer has a high risk of consolidation settlement because of draining during main excavation. Thus, high water tightness is required for this earth retaining wall. This paper reports design and construction methods for the Underground Soil–Cement Steel Diaphragm wall introduced as a part of the body of the subway station.1. OUTLINE OF SHIN-YOKOHAMA STATION 1-1. Location and structure of Shin-Yokohama Station Shin-Yokohama station is an intermediate station on the ST line connected to the Tokaido-Shinkansen bullet train, the JR-Yokohama line and the Yokohama Municipal Subway. Access to Tokyo and the Tokaido- Shinkansen from the eastern part of Yokohama city will be improved by this project. In addition, the number of estimated passengers of this station is one hundred thousand people/day because a soccer stadium (Nissan Stadium: 72,000 people), a huge indoor arena and a hotel are located in this area. This station consists of 4 stories and 3 spans (Max width; 29m, Depth; 33m, Length; 325.5m). Completion image is shown in Figure 2. Generally, stations have 1 platform and 2 trucks. But this station has 2 platforms and 3 tracks because some of ST line trains return at this station and a train deadheads from Hazawa station to this station in an emergency. This station is planned as 4 stories underground station, and the platform is on the lowest story. The reason why this station is in such a deeper position is to prevent the alignment from interfering with the Yokohama Municipal Subway station and foundation piles for bridge piers existing along the alignment. Even under the constraint conditions, earth covering should be shallow as much as possible. As a result, the tunnel edge is very close to the foundation pile, and the gap is only about 2m (Figure 3). In addition, passengers will be able to change trains easily from the ST line to the Yokohama Municipal Subway or vice versa at this station."

Jan 1, 2016

By R. C. Bunge

A magnetogravimetric separation is the consequence of two competing forces with opposing directions, i.e., magnetic buoyancy and gravitation (or centrifugal force). While magnetic buoyancy is a function of particle volume, gravitational force depends on particle mass, thus permitting a separation according to specific gravity. Since magnetic buoyancy is not a phenomenon of common knowledge, this chapter is meant to briefly introduce the theory of magnetogravimetric separations. A particle that is suspended in a magnetic fluid which is exposed to an inhomogeneous magnetic field experiences a repulsive force -the so called magnetic buoyancy. In order to illustrate this effect, an analogy with the more familiar hydrostatic buoyancy is drawn. Hydrostatic buoyancy occurs due to unsymmetrical pressure distribution 'above' and 'below' a suspended particle (fig. 1).

Jan 1, 1990

By A. Taghavi, I. Hassan, A. Solecki

"The Eglinton Crosstown Light Rail (LRT) Project is part of an $8.4 billion investment to expand transit in the Toronto, Canada area and is the largest transit project initiated in Province’s history. Settlement control and impact to over 1400 adjacent structures due to tunnelling was identified early as a critical project risk. The ground conditions along the 10km tunnel alignment consist of water bearing soft ground deposits (clays, sands, silts) which required careful analysis and control during design and construction. This paper will describe the process used to analyze settlements along the numerous of adjacent structures and evaluate achieved settlement results to those used during design. The paper will demonstrate that with the appropriate design specifications, selection of modernized EPB machines, and contractor performance, settlement can be maintained well below typical industry (volume loss) standards, expanding the application and suitability of soft ground tunnelling in sensitive settlement areas. INTRODUCTION The Eglinton Crosstown Light Rail Transit (LRT) Project is part of an $8.4 billion (2010$ CND) investment from the Ontario provincial government to expand transit in the Toronto, Canada area. The project is being developed by Metrolinx, an agency of the Government of Ontario to provide 19 kilometers of dedicated LRT service connecting the City of Toronto from the west to east along Eglinton Avenue. Upon completion in the year 2020, the Crosstown will be the first LRT constructed in Toronto. It will link regional and local transit, cut travel time along the route by half and provide over a thousand jobs during construction."

Jan 1, 2016

By J. Moreno, P. Sinton, R. Vogwill

Groundwater models are often used to estimate and optimize dewatering volumes, locations, and rates, as well as water supply production for mines. Projections of future dewatering rates are highly dependent on the conceptual model used as a basis for the numerical model. This paper presents an audit of modeled dewatering rates versus actual data and an examination of the reasons for discrepancies. The setting is a gold mine, in a collapsed volcanic crater breached by the ocean. Mining will occur to about 200m below sea level within a remnant geothermal system. A detailed hydrogeologic investigation was conducted to support dewatering and geothermal depressurization design for future mining operations. These studies included development of a three-dimensional model to simulate heat and density-coupled groundwater flow, using software developed by URS/Dames & Moore. In this paper, the groundwater modeling results prepared 5 years previously by others was audited using operational dewatering data. This model was then extended using the new mine schedule and actual locations for dewatering wells to predict future dewatering requirements. In addition, a comparison between “hot” and “cold” model results was used to assess the need to use a heat-coupled versus a standard groundwater model for dewatering predictions.

Jan 1, 2003

By P. Jonsén

Understanding mill charge motion is important. In the charge, the centre of gravity is shifted from the rotational centre of the mill system, and its motion is induced by rotation of the mill, while at the same time the charge creates a torque into the mill system. Breakage of ore particles and wear of liners/ball media are closely linked to the motion. To study these phenomena in a physically correct manner, numerical models for different parts of the mill system are needed. Validations of such models are scarce, because of the difficulty to measure in a tumbling mill. Experimental measurements in a lab mill were done for diverse load cases: varying feed materials, mill fillings, mill speeds and pulp liquids. The mill is set up to directly measure the charge-induced torque. The accuracy is good with relative uncertainty smaller than ±2% for relevant load cases. A full three dimensional numerical model of the whole mill is used to predict induced torque. Agreement between predicted and measured torque at steady-state is good. In addition, the model can accurately predict the mill start-up behavior for torque and mill power. This proves that the model is physically correct, and can be used for full-scale mills.

Feb 27, 2013

By Steven A. Savage

Agrico Chemical Company, as we presently know it, is the result of the coming together of several different fertilizer operations. The Williams Companies, our parent organization, first entered the fertilizer business in 1971, when it acquired the fertilizer operations of the Gulf Oil Company. This gave us, among other things, the manufacturing facility at Donaldsonville, Louisiana. In 1972, The Williams Companies acquired Agrico Chemical Company from Continental Oil Company, bringing in a manufacturing facility and phosphate mines at Pierce Florida. Our Florida Mines are in the region commonly known as the Bone Valley Region of Florida. The majority of the phosphate fertilizer produced in the United States utilizes rock mined in this region. The Donaldsonville Plant was originally built in 1967-68 on the site of the old Faustina Plantation at an approximate cost of $80,000,000. (This plant is commonly referred to as our Faustina Plant.) Until such time as Agrico was acquired from Continental Oil, the Donaldsonville Facility was solely used to upgrade phosphoric acid into finished granular products.

Jan 1, 1986

By V. C. Koppe, J. F. C. L. Costa, D. M. Marques, A. Amaral

Errors associated with estimating the grade of an attribute of interest in a deposit can compromise planning, sequencing, and mineral beneficiation decisions. Several factors are associated with estimation errors. Among them, we can highlight the factors associated with sample spacing, the size of production volumes, and the variability of the attribute considered in the estimation. The access to estimation error can be obtained by some geostatistical methods, for example, by stochastic simulation. However, this is a process that in some situations is computer intensive and takes time. Previous works have proposed a simplified method to access the Maximum Estimation Error (MEE) associated with different types of grade variables, depending on the sample spacing, at small production volumes and considering specific coefficients of variation ranges. This paper presents an approach to assess the MEE associated with long-term volumes. Considering the methodology proposed, it is possible to approximate if a specific drilling pattern used in a deposit provides an acceptable pre-determined estimation error for Resource Classification. Results and considerations on the impact of the geometry of larger production volumes on the MEE calculation are also presented.

Jun 25, 2023

By M. C. Roberts

The material composition of product is defined as the quantity of metal used per unit of product manufactured during a year. This ratio measures the efficiency of converting a ray material into final products. The material composition of product has shown steady and persistent declines over time for most metals and materials. This tendency demonstrates the continued improvements in manufacturing technology, resulting from substitutions of other materials and improvements in production efficiency. The purpose of this paper is to study trends in the material composition of product to reveal the impact of advanced materials on the use of traditional metals.

Jan 1, 1990

By T. A. Laser

"INTRODUCTION A positive workplace environmental, health, and safety (EHS) culture affords organizations and corporations many benefits, including increased trust and employee morale, sustainable EHS performance improvements, and reliable productivity and profit margin growth. Unfortunately, many leaders and EHS professionals struggle daily to achieve and maintain positive workplace cultures and consistent business results. While lack of management support, corporate or employee buy-in, resources, and time are common factors that conflict with an EHS culture and safe work behaviors and processes, there are many other actions that threaten the positive attributes of an organization’s culture. Often these culture killers are not recognized, or worse yet, ignored because they are considered taboo. For example, voicing observations or questioning long-held management practices or process that were initially designed to promote EHS values, but no longer do so. Unfortunately, this could be viewed as challenging authority, not being a team player or even not valuing EHS. And for those that speak up, the potential for negative consequences can be real impediments to positive change. Having an open mind, constantly striving to identify culture killers, and putting forth the effort to eliminate them are the first steps to begin reaping the benefits of having a sound workplace culture. This paper helps readers to: • Recognize culture killers that negatively impact fostering and maintaining sustainable EHS cultures in the workplace. • Understand how to prevent, avoid, and respond to culture killers, before they wreak havoc in your organization. • Assess EHS culture strength, and implement plans to continuously improve it. The desire to draw boundaries around concepts, put things into boxes, and nail down requirements for something that is virtually impossible to solidify for any length of time is quite fascinating! These desires can pose challenges when trying to define what the perfect EHS culture should look like. The very act of trying to define our culture tends to create silos, and these silos, in turn, can become “culture killers”. The following is one of the most common culture killers. UNBALANCED ORGANIZATIONS TRIGGER CULTURE KILLERS Unbalanced organizations occur when an organization’s constantly shifting focus forces other important needs to take a back seat--until the focus changes again. This balancing act can be detrimental and lead to catastrophic results including low morale, lack of trust, employee dissatisfaction, high turnover, increased incidents, poor profit margins, loss of market share, and ultimately into organization-wide failure."

Jan 1, 2018

By C. W. Schultz

Earlier publications from The University of Alabama have indicated that column flotation performance is improved when operating at low pulp levels and when the feed is directed into the froth phase. To validate these early observations a series of tests were performed in which the position of the feed entry to the column and the pulp-froth interface were systematically varied. The optimum grade-recovery relationship was achieved with high feed entry (WA) of column height) and very low pulp levels (<10% of column height). The position of the pulp-froth interface appears to be the more critical variable. When operating in this mode (1. e. at low pulp levels) column flotation becomes. in reality. a froth separation process.

Jan 1, 1991

By Ulrich Maidl, Marc Comulada, Janosch Stascheit

"INTRODUCTION Cohesive soils are notorious for causing clogging of the cutter head and the excavation chamber of tunnel boring machines (TBMs). While clogging leads to a drastic reduction in excavation performance, it further induces higher wear of tools and other parts of the cutter head and may even prevent a controlled support of the tunnel face and, thus, lead to face collapse and excess settlements or sinkholes. Employing well-balanced soil conditioning techniques, the clogging tendency can be significantly reduced. The monitoring and control of soil conditioning as well as the timely detection of potential clogging tendencies require a close monitoring of all relevant machine parameters and measurements. To this end, a reliable and powerful Process Controlling software that gathers all machine and process-related information is a prerequisite for successful mitigation of clogging-induced problems. The remainder of this contribution is organized as follows: First, a brief introduction to the Process Controlling system PROCON is given. Afterwards, the mechanisms and mitigation techniques of clogging are discussed. Finally, an example is given how Process Controlling has been employed to soil conditioning in a tunneling project with highly clogging soils.PROCESS CONTROLLING Being both the active part and a huge measuring device, the shield machine represents the core component in mechanized tunneling. This machine comprises a manifold of complex components and devices that require constant supervision and control and, thus, is equipped with a manifold of different sensors that provide a continuous monitoring of the state and condition of the machine (Maidl & Stascheit, 2014). If these data are put into the whole context of the tunneling process, they can provide insight to the assessment and optimization of the performance and to the prediction of potential risks and hazards such as, for example, the tendency of clogging of the cutter head."

Jan 1, 2016