Search Documents

By P. R. Pereira

This paper presents a comparison between the simulations of a semi-empirical model and a theoretical model for the prediction of radial stress in rock. The results of the simulations were compared to the results of a field test. The comparison of the radial stress predictions shows that in the semi-empirical model use of the plane wave approximation as the basis for the prediction of the radial stress provides a much better result than the theoretical model. The theoretical model includes the correct elastic wave geometry and theory but fails twice, firstly by considering the charge as a point (unit) energy source therefore; and secondly by using a Delta function with a very sharp rise and decay time to simulate, with no distinction between non-linear and linear zones, the attenuation of the energy per unit volume at the shock wave front as the wave moves away from the borehole. The results of the semi-empirical model were within the same order of magnitude as the results from the field test whereas only one result from the theoretical model came close to the result of the field test. However, even this closer result for the theoretical should be taken with caution as there was no measurement in the field test made at this distance from the borehole. Finally, because of its potential portability, convenience, and cost-effectiveness the theoretical model can be a most valuable tool for mining and civil construction operators in the early design of blasting rounds and of the mining operation itself.

Jan 1, 1993

By I. Weir-Jones

I. Introduction The experimental work described in this paper was carried out during 1967 and 1968 in an inclined reinforced concrete adit which had been driven during 1965 and 1966 to provide primary access for a new gypsum mine. The new mine was situated near the village of Sherburn-in-Elmet in central Yorkshire in an area of extensive post-glacial plains of deltaic and lacustrine origin. These plains cover a large area of this part of Yorkshire extending inland from the coast for a distance of about 35 miles. The gypsum deposit at Sherburn dates from Permian times and it is considered" to have been associated with the western-most edges of the ancient Zechstein Sea which was also responsible for the formation of the extensive evaporite deposits in north-east Yorkshire. The gypsum deposit, which varies in thickness from 10 to 15 feet, is extremely pure and it occurs quite close to the surface; in the Sherburn area the overburden is only 120 feet thick. The proximity of the deposit to the surface, however, tends to give a somewhat false idea of the magnitude of the problems associated with its extraction. These problems were all related to the nature of the overlying strata. As has already been mentioned, the surface deposits are post-glacial and they consist of an extremely large number of thin layers of varved clays, fine silts and sands extending down to a depth of 75 feet. From the bottom of the post-glacial deposits to the seam, a distance of about 45 feet, the strata consists of a succession of marls, weak sandstones, and siltstones, which although they are inherently incompetent materials, are appreciably stronger

Jan 1, 1971

By E. R. Pantos

US coal production increased 3% to a record 832 Mt (917 million st) in 1987, according to preliminary Energy Information Administration (EIA) data. Most of the increase was due to the unusually warm summer and the increased coal-fired electricity demand for air conditioning. Drought conditions in the Northwest lowered hydroelectric generation, contributing to the higher use of coal by electric utilities. However, excess production capacity and increased competition from natural gas added further downward pressure on delivered coal prices, continuing the declining price trend of the last several years. Coal production by region Appalachian coal production reached 402 Mt (443 million st) in 1987. This is about 3% more than in 1986 and just short of its 1984 peak. Virginia produced 7% more than its 1986 level, due to increased coal-based electricity demand. Smaller percentage increases were attained in eastern Kentucky, Pennsylvania, and West Virginia. Ohio and Alabama were the only major coal-producing states in Appalachia that produced less coal in 1987 than in the previous year. In the Interior region, 1987 coal production reached a record 182 Mt (201 million st), about 2% above 1986. Illinois is the largest coal-producing state in that region. Production there fell about 3.7%, primarily because of lowered demand at electric utility plants in Alabama and Tennessee. However, this was more than offset by production increases in western Kentucky, Texas, and Indiana. After falling slightly in 1986, coal production in the West resumed its upward trend to a record 248 Mt (273 million st). Wyoming is that region's dominant coal producer. It mined 7% more coal than in 1986. Wyoming's increase offset the 11% decline in New Mexico production and smaller declines in other Western states. Coal consumption and prices Domestic coal consumption reached a record 759 Mt (837 million st) in 1987. Most of the increase resulted from the unusually warm summer that led to higher than normal peak demands for electricity in the third quarter. Electric utility coal consumption was also boosted by the below-normal hydroelectric generation that resulted from low water levels in the Northwest. These factors more than offset the effects of increased nuclear power generation and competition from natural gas. As a result, coal provided 56.9% of electric utility generation in 1987, compared with 55.7% in 1986. Electric utilities consumed a record 651 Mt (718 million st) of coal. While electric utility coal consumption increased, the average cost of coal to utilities was down, from $1.58 per million Btu in 1986 to $1.52 in 1987. The average price of coal delivered to utilities in 1987 was $35.09/t ($31.84 per st), the lowest since 1981. Coal prices were held down by a glut of coal supplies and by a decline in the average price of natural gas to electric utilities. Coal consumption at coke plants in 1987 was 2.6% above the 1986's 32.5 Mt (36 million st). This increase reflects steel's recent resurgence. Coking coal demand, though, was reduced by the increased use of continuous casting and electric furnace technologies. The average price of coal delivered to coke plants fell from $56.02 to $51.35/t ($50.83 to $46.59 per st). Coal consumption in the industries other than coke plants amounted to 68.2 Mt (75.2 million st) in 1987, slightly less than in 1986. Coal lost part of its market share to natural gas, which was priced favorably relative to coal. The average price of coal delivered to manufacturing plants was at its lowest level of the current decade. It fell from $39.50/t in 1986 to $37.27/t ($35.84 to $33.81 per st). Residential and commercial coal consumption fell to 6.2 Mt (6.9 million st) that is 9.8% below 1986 and the lowest since 1980. This decline is also attributed to the relatively low price of natural gas in 1987. Coal stocks Coal consumers held 169 Mt (186 million st) of coal stocks at the end of 1987, 5.9% above the 1986 year-end level. Most of this increase was due to stockpiling by electric utilities in anticipation of a possible strike by the United Mine Workers of America early in 1988. Stocks at electric utilities increased to an estimated 154 Mt (171 million st) at the end of 1987, 5.6% higher than the previous year. This was much lower than 1984's stock buildup. Coke plants increased their coal stocks by 30% in 1987 to 3.5 Mt (3.9 million st), rebounding from the unusually low inventories of 1985 and 1986. Other industries increased their stocks slightly in 1987. Coal producers and distributors ended 1987 with 25 Mt (28 million

Jan 5, 1988

By C. H. Sheerin

Remotely located in the jungle near mount Puncak Jaya [16,500 ft (5,030 my), Irian Jaya, Indonesia rests Freeport's Indonesian copper mining operation. Shortly after start up of Freeport's copper concentrator in 1972, lower than estimated throughput was experienced within the crushing circuit. Within one year, Freeport had successfully engineered a solution, and was operating a 5,500 dmtpd wet screening circuit. Today, after 19 years of successful wet screening expansion and operation, the concentrator processes 57,000 dmtpd.

Jan 1, 1993

By Thomas P. Meloy

Floating "fines" differs from floating "sands" because the fines have a much larger surface area compared to their mass. The forces that arise from this large specific surface the key to understanding the behavior and treatment of fine particles. Though the nature of these forces is not thoroughly understood, enough work has been done to give a qualitative picture of what is happening in a flotation cell. It is the purpose of this chapter to re-examine some of the more, recent theoretical work and-to indicate its importance.

Jan 1, 1962

By Robert G. Woolery

Union Carbide_ began looking seriously at heap leaching in 1971. At that time some 1.6 million tons of mineral averaging 0.040% U308 were stockpiled at various sites around the Gas Hills, Wyoming, uranium facility. Several alternatives for economically exploiting these reserves were considered and heap leaching seemed the most attractive. At the time, Western Nuclear Inc. was operating a heap leach project nearby in which the low-grade ore was leached with sulfuric acid, the product liquor treated in an on-site solvent extraction circuit, and the stripped product liquor re-acidified and recycled. They were most generous in allowing us to visit their site, answering our questions, and were helpful in discussing the problems associated with heap leaching. They confirmed our belief that, it was possible to operate a heap leach profitably on material too low grade for. conventional milling. Based largely on what we had learned from Western Nuclear's experience, a program was set up involving a laboratory study to determine the characteristics of the mineral stockpiles as related to heap leaching and to conduct a pilot heap leach adjoining our Gas Hills mill. Basically, the pilot heap construction and leach procedure were similar to those described in the literature(1,2) with certain modifications to permit detailed monitoring of the operation. In May, '1972, the decision was made to construct a test heap. The UCC plant at Gas Hills, Wyoming was selected as the most appropriate site for the follow¬ing reasons:

Jan 1, 1977

By C. G. Hunkin

In situ, or in-place leaching is concerned with the extraction of metals from natural mineral disseminations without removal from their geologic location which, in many cases, amounts to the reversal of the deposition process accompanied by a presumed increase in velocity of the processes, if the project is to be profitable. Solution mining processes involve removal of minerals such as sulfur, common salt, and potash, generally leaving cavernous voids, in contrast to in situ leaching which term is applied to the selective dissolution of a mineral from its gangue without sensible disturbance of the formation. Where such a process can be operated, the advantages are manifold and have been so recognized by miners from the earliest days of mining. Recent technological developments have encouraged a reassessment of the status of in situ leaching, and it now appears possible to extend the application of the method from a few isolated special situations to many uranium and copper deposits. Anaconda's interest in the techniques stems from long experience with vat and heap leaching, 'dump leaching, and natural leach activities associated with several established mines. Increasing activity through-out the industry has been noted, particularly in leaching low grade pillars and the peripheral zones of operating mines, often by the introduction of leach solutions via boreholes drilled from surface. Reactivation of dormant mines] using similar techniques has been successful. Over the long term, environmental improvement activity will lead to excess sulfuric acid production, even to a disposal problem. The cost of leach solutions and reagents must be reexamined in this light. The mineral industry now classifies as uneconomic deposits of readily soluole minerals whose potential value, on a per acre basis, may De several times that of many currently profitable oil field reser-

Jan 1, 1971

By J. P. Ducarme

The eastern U.S. contains vast reserves of thin seam coal deposits, particularly in the Appalachian mountain region. These typical 355 to 710 mm thick reserves are difficult or uneconomical to recover with present technology. The U.S. Bureau of Mines is developing technology that would allow nearly 100% recovery of thin seams in these mountaintop regions. This paper details the research that has been conducted on these new techniques and presents results of testing on a cross-ridge full-scale physical model.

Jan 1, 1994

Little knowledge is available that considers the effects of continuous miner position on the possible respirable dust exposure of the remote mining machine operator. Such information could be very useful for increasing the awareness of the remote operator as to those parts of an extended cut that generate higher levels of respirable dust. This data could be used to develop guidelines for positioning the remote operator to reduce his potential exposure. This work details the effects of continuous miner position on dust levels measured on the machine and at the remote continuous miner operator location.

Jan 1, 1998

By R. J. Pruett

Selective flocculation enables the production of high-brightness kaolin products from kaolin ore once considered too poor in quality for beneficiation into paper-coating pigments. Anatase, Ti(1-X)FeXO2, with X = 0 to 0.05, is a common iron-bearing impurity in sedimentary kaolin that can be unresponsive to kaolin beneficiation processes, such as magnetic separation, due to its extremely fine particle size (<0.3 µm), or chemical bleaching, because of its chemical stability. Described here are selective flocculation technologies that separate anatase by flocculating anatase or flocculating kaolinite from dispersed slurries. Applying the advances in the chemical and mechanical dispersion of ultrafine particles and the selective aggregation of kaolinite or anatase particles have resulted in the selective flocculation processes practiced today that have increased process recoveries from those technologies practiced beginning in the 1960s.

Feb 1, 2012

By Felicia F. Peng

The naturally occurring aged manganese oxide coated on the granular media was found to have a catalytic effect on the removal of low concentration of Mn(II) (-1 ppm) from drinking water. Applying this principle, a manganese removal technique was developed for removal of higher concentration of Mn(II) (-100 ppm) from mine drainage by using various aged filter media and synthesized granular media with manganese oxide coatings. Laboratory-scale continuous granular media column experiments were conducted to assess the feasibility of manganese oxide-coated granular media for Mn(II) removal from synthesized mine drainage. The removals of Mn(II) were evaluated as a function of operation parameters including solution pH, manganese oxide concentration coated on the media, interstitial velocity, and oxidant concentration of influent. Higher solution pH and/or higher manganese oxide concentration promoted the removal of Mn(II) on the oxide-coated granular media under low interstitial velocity. Addition of sodium hypochlorite as an oxidant in the influent resulted in continuously regenerated oxidized surface to serve as the catalyst for Mn(II) oxidation reaction on the surface of oxide-coated media.

Jan 1, 1994

By Steven Keim, Steven Stansfield, Kevin Andrews

Geotechnical, geological, and hydrogeological fieldwork and data collection for the mining industry is often conducted by younger, less-experienced staff members. In many cases, fieldwork personnel are recent college graduates or are otherwise relatively new to the mining industry. Due to busy schedules, staffing shortages, project budgets, and in some cases, poor management, new fieldwork hires often do not receive thorough training. In the past and the present, many workers in the mining industry learn(ed) by “doing.” While this is still considered to be the most practical approach and the easiest way for a company to determine the skill set of an employee, there is always some risk involved in the “feet to the fire” method. The reality is that field personnel are often collecting data on which major operational decisions will be made or on which regulators will base enforcement decisions. Inadequately trained or inexperienced field personnel may collect inaccurate data or fail to recognize key conditions that may influence decisions made by regulators, design engineers, mine managers, and corporate leaders. Even the best engineers may come to incorrect conclusions if they are starting with poor input data. Decisions based on inaccurate data often result in delays, budget issues, unsafe conditions, or even worse consequences. This paper provides numerous mining industry examples of incidences where inaccurately collected field information did, or could have, resulted in major adverse consequences. The paper also offers some simple approaches to minimizing the potential for such problems.

Jul 1, 2023

By K. C. Ko

The pit slope angle dictates the economics as much as the depth of the pit. Steeper slope provides more ore reserves, at the same time, the steeper slope presents higher probability of instability and associated maintenance problems. While large open pit mines mostly belonged to nonferrous metals in the past, other mines are becoming deeper as the mine economics permits deeper mine operations, Such minerals include coal, uranium, phosphate, and others. There are some basic differences between an open pit slope and slopes that are encountered in usual civil engineering work such as dam embankments and highway cuts (Figure 1). The stability of the civil engineering slope changes continuously with time due to ground-water movements, weathering, etc. But the stability of the open pit slope (Figure 2) changes more drastically day-to-day or even hour-to-hour, These changes occur because not only is the slope geometry being continuously changed by the mining operation, but also different geology and geologic structures are being exposed on the slope. Even when a particular slope area is not presently being mined, excavation in adjacent areas can affect the general condition of that slope area. A pit will experience some slope failures during its life.

Jan 1, 1977

By R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (K088) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron-and steel making and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By W. G. Miller

A series of computer programs for the analysis and mapping of coal-related data has been developed at the Illinois State Geological Survey; these programs, known collectively as the Coal Data System, represent the latest achievements in computer processing of geologic data at the Survey. Building upon programs previously developed in the Survey&apos;s Computer Services Unit, they expand the scope of the computerized data base that the Survey has been using for analyzing coal-related data. The System was partially developed during a joint study by the Illinois State Water Survey and the Geological Survey entitled, ?Coal and Water Resources for Coal Conversion in Illinois.? 2 In that study the available coal reserves more than 42 inches thick in the two principal coal seams throughout the state were mapped. The System was used to calculate the coal reserves and to report the average number of tons of coal in place per square mile in each township (Figures 1 and 2). It also produced maps of the coal features of sufficient quality to be printed on material that was scribed as master copy for the printing of full-color 1:500,000 scale maps (see Figures 3 and 4).

Jan 1, 1975

By B. A. Slaker, T. Miller

"An underground limestone mine in eastern Ohio was experiencing significant floor heave and roof falls, attributed to high horizontal stresses. Areas of the mine showing floor heave were monitored with roof-to-floor extensometers and photogrammetry surveys, to determine the rate and magnitude of heave. Extensometer data were recorded hourly at four locations across adjacent entries while photogrammetry surveys of the floor were performed at the same locations every two to five weeks. A final survey was performed using an I-Site 8200 laser scanner. Following instrumentation, floor heave up to 10.1 cm (4 in) was measured by the extensometers, photogrammetric reconstructions, and laser scanner over a 6-month period. The extensometers were biased by the location where they were placed, failing to consistently capture the location and extent of floor heave and cracking. The photogrammetry surveys were not precise enough to capture small magnitude movements. Mining in the area was halted and within several months the floor movement and incidence of roof falls was significantly lessened. INTRODUCTION Limestone formations in the United States can be subject to relatively high horizontal stresses due to the presence of tectonic loading of the strata. Horizontal stresses have a documented history of causing stability issues in underground limestone mines. Kuhnhein and Ramer (2004) discussed the influence of horizontal stress on complex ground control interactions associated with limestone pillar design and mine layouts. Esterhuizen et al. (2008) documented roof damage observations associated with high horizontal stresses such has roof guttering, beam instability, oval-shaped falls, and failure propagations. There have also been a number of documented case histories of horizontal stress causing unexpected roof and pillar failures at shallow depths (Stacey and Yathavan, 2003). To the knowledge of the authors, there has only been one well-documented case of floor failure causing stability issues in an underground limestone mine. Murphy et al. (2015) documented the role that a weak, moisture-sensitive floor had in the development of a massive roof collapse. For this paper, the study site neighbored, and was in the same general geology of, the site in Murphy et al. (2015). However, the weak, moisture-sensitive floor was not present for the current study. The current study site has experienced significant floor instabilities caused by high horizontal stresses. The instability area was monitored using two different methods to determine if the floor failure would eventually propagate into roof or pillar failure. The objective of this paper is to analyze displacement monitoring measurements from string potentiometers and remote sensing techniques in an area experiencing active movement. Based on the measurement trends and observed damage from inside of the mine, the presumed failure process will be discussed."

Jan 1, 2017

By M. R. Yalamanchili

Recently, noequilbrium electrokinetic measurements using laser-Doppler electrophoresis were reported by Miller et al. (1992) for alkali halides and the sign of their surface charge thus determined. These results are generally as expected from simplified lattice ion hydration theory with KCI, under normal circumstances, being the most significant exception. In this regard, lattice defects (F centers and oxygen imperfections) have been found to influence the surface charge of KCI and its electrophoretic mobility. In particular, the presence of oxygen defect states in the crystal lattice has been found to be responsible for KCI&apos;s unexpected behavior. The concentration of oxygen defect states in KCI, as characterized by UV/Vis absorption, was varied in order to study their influence on the electrokinetic behavior and subsequently on the flotation response of KCl. At low oxygen contents « 60 ppm) KCI is positively charged as expected from lattice ion hydration theory. However, typically, KCI contains substantial oxygen (>300 ppm) sufficient to impart a negative surface charge which accounts for the selective flotation of KCI from NaCl by hetero-coagulation with oppositely charged alkyl amine hydrochloride collector colloids.

Jan 1, 1994

By Michael J. Beus

This paper describes research conducted under the BuMines&apos;s Advancing Metal and Nonmetal Mining Technology Program, a major element being the application of new and improved technology to shaft design in deep underground vein-type mines. Two basic design parameters considered in shaft planning are configuration (shape) and ground support. The most common shapes are circular and rectangular. Ground support systems include concrete, timber sets, steel sets, rock bolts, and steel liners. The inherent advantages and/or disadvantages of various shaft designs such as ventilation and fire resistance, flexibility and ground support characteristics are well known. Circular concrete-lined shafts have minimal resistance to air flora and are virtually fireproof, an important consideration in deep hot mines. However, concrete does not yield significantly, and failure conditions and misalignment cannot be easily repaired. Timber-supported rectangular shafts predominate in the Coons d&apos;Alene Mining District with its highly stressed and frequently heavy ground. The sets can be relieved and reblocked when out of alignment. However, the constant maintenance and repair requirements result in exposure to an inherently dangerous working environment combined with excessive operating costs. Obviously a dilemma exists--a circular, concrete-lined opening has many desirable features, provided it is strong enough to withstand the stresses involved. Rectangular, timber supported shafts have proven adequate in the Coeur d&apos;Alenes; however, the implication of increased maintenance and repair requirements on ever-deepening shafts in this district and other similar areas will be an important design consideration in the future. This paper, then, presents shaft-configuration and ground-support guidelines to help remove some of the uncertainty concerning the stresses to be encountered in typical deep vein mining areas.

Jan 1, 1976

By John G. Oldsen

During the last several years, implementation of trusses, in lieu of wood cribs, has been successful for supplemental tailgate support in the Pittsburgh seam. This paper reviews the truss support system provided by the new high strength 0.6" tensioned cable truss, which is now also being used in cribless tailgates. Cable loading and roof deformation were monitored to evaluate roof and floor performance. The test results indicate that the cable truss system successfully controlled the roof and floor during the first and second panel extraction. This paper will describe the advantages of cable trusses and their load transfer mechanism as well as mine evaluation.

Jan 1, 1997

By A. L. Holmes

Since the 1981 record of 54 mm tons of US fertilizer consumption, grain surpluses in the US have brought about massive acreage reduction programs, decreased fertilizer consumption, and resulting price pressures caused by excess capacity. The strong US dollar that reduced export sales of both grain and fertilizer, and new offshore manufacturing capacity using US engineering/contracting know-how have combined to put US producers of phosphate fertilizers in uncompetitive postures. While recent events suggest the industry may be growing out of this capacity problem, the cost of US phosphates will continue to be disadvantaged by such external factors as taxes, environ- mental regulations, and high power costs. There is no reason to expect help from the government in the form of reduced environmental regulation and taxation. In order to survive, phosphate fertilizer producers will have to develop technologies and adopt strategies that result in world competitive production costs. Current responses to the need to reduce costs include reduced energy costs through cogeneration, innovative reclamation techniques that create valuable land, and in- creased raw material recovery achieved by operator proficiency. While new technology offers long-term benefits for the producer, present efforts are concentrated on more mundane management efforts to reduce costs. Major attention is being given to the problems of labor utilization and productivity. Raw materials suppliers are being asked to renegotiate contracts which more appropriately reflect conditions in an industry operating at about 50% of capacity. Achievements in these and other areas will allow the producers to continue operating until longer term benefits materialize. `

Jan 1, 1986