Search Documents

By Raymond E. Zimmerman

The cleaning of coal by the use of jigs is one of the oldest methods of separating coal from its impurities. Although in many situations jigs have been replaced by other methods, by far the largest percentage of coal today is still being cleaned by some form of jigs. Some piston- or plunger-type jigs are still in use throughout the world; however, the greater number are air pulsated, generally called the Baum jig, named after the original inventor, Fritz Baum of Germany. This standard jig, with slight modifications, has been in use for over 75 years. Up until recently, however, it has had certain limitations in obtaining the high performance and efficiencies required in modern coal preparation practice. TO improve its performance, some radical modifications have been made in its design and operation SO that there is now a Baum-type jig giving much higher performance in terms of capacity, efficiency and sharpness of separation- This new jig is called the Batac, and the purpose of this paper is to describe its characteristics and present data giving its performance in treating coarse and fine sizes of coal.

Jan 1, 1974

By John J. Mancini

Elastomeric liner products have been used for over two decades in a wide variety of uses including pond liners, hazardous waste barriers, dam face rehabilitation and mining applications. Asphalt blended with polymers is enjoying renewed interest in the engineering community because of its durability, high yield attributes, fewer CQA steps due to seamless installation, and ease of installation and repair. As in other lining technologies, advancements in polymer chemistry and improvements in installation techniques have had dramatic impact on the quality of fluid-applied asphalt (FAA) membranes. Membrane 6, man­ufactured by Deery Oil, Inc. for over 16 years is a hot-applied polymer modified asphalt membrane that can be applied to a variety of substrates in a reinforced configuration or installed directly on an asphalt surface. By blending thermoplastic polymers with asphalt, very favorable stress/strain characteristics can be achieved (Chambers, 1980). Typically the membrane will yield under rel­atively low stress and also exhibit high elongation capability. In service applications where puncture resistance is a concern, fluid applied asphalt materials have the flexibility and com­pressive strength under heavy loading that leach pad designers may find attractive. Additional security is achieved if long term service life is important as in the case of radioactive waste con­tainment. The Department of Energy selected Membrane 6 over seamed liners for a surface barrier that must isolate and contain radioactive waste for 1000 years. Asphalt has a long history of use as a water-stop material and it is believed that this natural construction material combined with SBS polymers will per-form for a millennium. (Freeman, 1994) The process of installing Membrane 6 varies according to job size and the type of surface to be protected. Lining applica­tions on compacted substrates require the membrane to be applied to a scrim cloth (fig 1). Some early pioneers in FAA technology neglected this step and therefore never achieved per­formance levels that satisfied regulatory guidelines. The scrim provides a cohesive surface that promotes membrane flow while achieving high impermeability (2Xl0 '11).

Jan 1, 1996

By Kendall Y. Onstott

The paper presents the results of a plant test using WEMCO 1 + 1 enclosed flotation machines for inert gas (nitrogen) flotation of by-product molybdenite from copper sulfide concentrate. Copper depressant consumption in the rougher flotation stage was reduced by 68% as reagent consuming oxygen was removed from the flotation air. Unlike other nitrogen flotation systems used in the industry, nitrogen is recovered above the flotation cells and from froth in tails and concentrate streams and recycled, resulting in minimal nitrogen makeup requirement.

Jan 1, 1984

By D. C. McDonald, P. R. Whincup, H. Duke

Due to grade, overburden depth and stability and the presence of groundwater it was considered impractical to recover gold contained in unconsolidated palaeochannel sediments by conventional mining, dredging or borehole mining techniques. A series of field experiments was conducted to determine the feasibility of recovery of gold by in situ leaching from sediments located at a depth of about 80 metres. The test wellfield site and plant are described together with field test procedures, results and wellfield rehabilitation procedures. Choice of sodium cyanide as leachant and laboratory testing are discussed in relation to groundwater and sediment chemistry and problems encountered in field tests.

Jan 1, 1989

By R. Tamir

This paper will describe the benefits of utilizing the decision support system, DSS to support the methodology of structured decision-making in the mining environment. It will outline the layers of the mining related decision making – 1. Creation of “one truth” situational awareness utilizing 2. existing planning, ERP, operational and monitoring agents, a. Expressing plan verse performance across mining phases and functions compared with the actual and trends to evaluate performance. b. Creating alternate courses of action and the implications up and downstream. 3. It will review the current condition were although a multitude of technologies resolve multi variable issues they do not interact in a way that assists decision makers throughout the organization in making high-quality decisions that will push the overall performance envelope. 4. The paper will show the benefits of integrating military methodologies to resolve multi variable complexed issues (operational, financial and other), operating in changing environments in order to meet time sensitive objectives with restricted resources. This is achieved by creating a shared situational awareness thru incorporating information from a multitude of data generating agents, creating COA, selecting the appropriate and turning it into a plan. The paper will discuss the implementation and suggest a path.

Feb 1, 2023

By L. E. Garner

Aggregate resources should be considered primary factors in urban development. Resource planning is essential because land values, previous construction, or zoning restrictions often preempt exploitation of aggregate deposits within an urban area. Sequential land use practices allow development of areas prior to urban development. Population and aggregate consumption trends in Austin, Texas, indicate that substantial quantities of reserves will be lost to future development. Aggregate materials are present in nearby seas. However, a comparison of transportation and reclamation costs indicates that reclaiming land after mineral extraction can be significantly cheaper than transporting materials longer distances.

Jan 1, 1979

By Vas P. Srinivasa

This paper examines the role of the heavy media separator in the mineral industry. Procedures used in selecting the separating vessel, developing the process flowsheet, and designing a heavy media circuit are discussed. For comparative purposes, the capital investment and operating costs of different types of operation are included.

Jan 1, 1981

By Langtry E. Lynd

The titanium industry is based on the unique properties of titanium dioxide and titanium metal. Because of its whiteness, high refractive index and resulting light scattering ability, titanium dioxide in its two main allotropic forms, rutile and anatase, is the predominant white pigment for paints, paper, plastics, rubber, and various other materials. Titanium metal, because of its high strength/weight ratio and resistance to corrosion, is widely used for aircraft, both in airframes and engines, for powerplant surface condensers, and a wide variety of chemical processing and handling equipment. U.S. production of titanium dioxide pigment in 1979 was about 658,000 tons - 2/, valued at about $770 million. Net shipments of titanium mill products were around 19,000 tons, worth about $380 million. These two major uses account for over 96% of domestic titanium consumption. The third largest application, the use of rutile for coating welding rods, required about 9,500 tons of rutile concentrate, worth about $4 million. Other applications of titanium-bearing raw materials include the manufacture of titanium carbides, ceramics, and chemicals, and the recently developed use of ilmenite as a substitute for barite in well-drilling muds.

Jan 1, 1980

By Paul J. A. Lever, Robert H. King

Human operators, geological conditions, equipment changes, mining sequences, and roof conditions are some of the continually changing operating conditions that drive a dynamic mining environment. These dynamic characteristics make it difficult to automatically analyze mining data because attributes change as the mining environment changes. Mine monitoring systems could provide mine managers with much more useful information than they do presently, if automatic analysis were possible. Automatic analysis of sensor data is also key to autonomous mining systems. This paper describes artificial intelligence (AI) and sensor fusion based sensor data analysis techniques developed over the past four years. These techniques were used to classify machine operating events by continuously monitoring machine power usage in a continuous miner section at an under- ground coal mine. The result is a report similar to an industrial engineering time study. First, numerical pattern classification techniques broadly identify operating events. However, domain knowledge about inter-machine and intra-machine interactions is necessary to identify and refine dynamic event boundaries. By implementing AI and sensor fusion based techniques we are able to classify machine events more accurately and recognize more specific events. These techniques could easily be applied to many different mining sensor data applications

Jan 1, 1993

By D. E. Healy

In 1989 an Autogenous Grinding Task Force was formed to study potential autogenous grinding circuits to replace the existing semi-autogenous grinding at the National Steel Pellet Plant located in Keewatin, Minnesota. Pilot plant test work performed by the Hanna Research Center (HRC) indicated that fully autogenous grinding with pebble extraction and crushing could feasibly be incorporated into the existing circuits. In 1990, one of the existing ten grinding mills was converted for an in-plant test incorporating pebble crushing. The full scale test work conducted in 1990 and 1991 verified the pilot plant projections with primary mill throughputs from the fully autogenous circuit utilizing pebble crushing being greater than throughput of the existing SAG mill circuits.

Jan 1, 1992

By Rainer Antretter

The city of Garmisch-Partenkirchen in southern Germany is located at a main transit road to Tyrol in Austria and suffers of a very heavy traffic load. Therefore, the Kramertunnel as a by-pass tunnel is built to release/mitigate the traffic through the city centre. The 3,600 m long single tube road tunnel is designed with a parallel but smaller emergency tunnel and with cross passages, fitted with single- and doublesided emergency bays, a vent shaft, and an intermediate ceiling to separate fresh air supply from the road traffic. The tunnel, concrete lined along its entire length provided the challenge to find smart formwork solutions for quick set-up, repositioning, setup and pouring. Three particularly specific sections are discussed in this paper.

Jun 13, 2023

By S. R. Hutchins

Several refractory sulfide and carbonaceous gold ores were examined to determine whether microbial pretreatment could be used to enhance gold recovery. Test samples were biologically leached using unique, thermophilic microorganisms to solubilize iron sulfide minerals. Gold recovery from sulfide ores and concentrates was enhanced following pretreatment with the thermophiles; responses varied widely for the individual materials. Although bioleaching had little effect on the preg robbing characteristics of the carbonaceous gold ores, cyanidation of the bioleached residues yielded higher gold recoveries than cyanidation of the native ore. By combining bioleaching with abiotic processes designed to inhibit preg robbing, gold recoveries of 83-98% were obtained from carbonaceous ores yielding 10-50% gold recovery by direct cyanidation.

Jan 1, 1987

By Ray E. Williamson

One of the prime objectives of the mine industry is to develop a low cost way to clean up what has been called "The Rape Of Mother Nature". The project falls under the broad umbrella of reclamation, which is now considered an essential part of the mining cycle. As such, it is being given full consideration in the initial planning of all surface operations. In most areas, if a proposed mining system does not lend itself to proper reclamation, it is not an acceptable system. By combining mining and reclamation plans, a producer not only can minimize reclamation costs, but can also restore the land to usefulness and insure continuing profits after a deposit is depleted. As long as fifteen years ago, many of the larger mining companies were already deeply involved in this extra cost work. Even then the involved companies were projecting a great need for a bigger bulldozer, Bigger than anything commercially available. At that time, the D9 tractor weighed about 60,000# bare weight.

Jan 1, 1975

By Venkata Aneesh

This paper examines the desired blast fragmentation results associated with mining fleet performance at Sidney Quarry of Pike Industries, A CRH Company by reducing cycle times and hauling less oversize material generated from the blast to the crusher to increase the overall plant throughput. We are constrained with blast patterns due to the poorly sorted and fractured seams in the quarry, which is angled at 35° NE and dipping at 80° and runs parallel to the Interstate-95 highway on the east of the quarry boundary about 600 ft, making it challenging to alter the blast patterns for optimal yield. We evaluated multiple relationships between blast patterns in conjunction with loader diggability. Results analyzed include the digging hours, fleet cycle times, and the fragment size with the optimized blast design through 3GSM software to arrive at the optimal yield to maximize the crusher throughput. Our primary objective is to focus on safety with efficient cycle times and clean floors & clean face generation for better operational efficiencies. Secondly, to optimize the crusher yield which is an integral part of quarry operation. Further, this paper provides the utilization of 3GSM blasting techniques in quarry applications with computer vision fragmentation analysis and VizaLogix, a fleet management software to analyze the cycle times sampling.

Feb 1, 2024

By Swan. J. D.

Repairing and replacing equipment damaged by corrosion and abrasion is a major cost throughout industry, especially in the coal mining industry. Careful study of corrosion and abrasion, and their causes and effects, often leads to the selection of alternative materials which can provide economies. What, actually, are corrosion and abrasion and how do they contribute to the cost of operating a coal-preparation plant? Furthermore, what can be done to alleviate corrosion and abrasion problems and thereby reduce operating costs? These questions will be answered in the following discussion, which will describe the destructive action of corrosion and abrasion and give several methods for controlling corrosion and abrasion losses, These methods include the substitution of stainless steel for carbon steel, the use of corrosion inhibitors, and the use of design to eliminate corrosion and abrasion. Examples will be given illustrating the benefits that have resulted in plant tests when these methods of controlling corrosion and abrasion were used.

Jan 1, 1970

By Jose F. T. Agapito

The mining engineer must be able to predict the structural behavior of the rock around underground openings so that he can answer questions relating to safety and economics. With the present status of rock mechanics knowledge, exact predictions cannot be attained and approximate idealizations are made. As a first approximation, structural design makes use of theory, laboratory testing of rock properties, and available experience from excavations in similar rock formations. However, realistic design can usually be obtained only after in-situ observations and measurements are made. After all the information is collected, judgement and experience play a most important role in the final formulation of the design. This paper describes part of a geotechnical program which was instrumental in obtaining information for the design of large oil shale pillars. The work was carried out during 1971 and 1972 in the experimental mine of the Colony Development Operation. Colony is an oil shale venture formed between Atlantic Richfield Company, Operator, The Oil Shale Corporation, Cleveland-Cliffs Iron Company, and Sohio Petroleum Company to conduct research and development in mining and retorting of oil shale, The property is located in the southern edge of the Piceance Creek Basin in northwestern Colorado, approximately 250 miles west of Denver (Figure 1) . Mining was conducted by the room-and-pillar method in a 60-ft high portion of the Green River Formation at a depth of 600 to 850 ft, Pillar dimensions are approximately 60 ft by 60 ft. The mine site is in the eastern face of the canyon containing the Middle Fork of Parachute Creek, The distance from the mine to the side of the mountain varies from 500 to 1,200 ft, and its height above the stream floor is approximately 700 ft.

Jan 1, 1974

By L. Donovan Clark

The term "powder factor" is almost universally accepted as the measure of the efficiency of a blasting program. It represents the economics of blasting since it designates quantity of explosive (thereby providing quality control in rock fragmentation) in terms of the associated volume broken. It is the wide use of this concept that explains the interest shown in an approach to rock blasting preferred by A. W. and Z. W. Daw* in a treatise on 3 blasting (1) substantiating its use in the form, Q = CVW3 for single shot hole, where Q = quantity of explosive lb Cv = blasting coefficient W3 = unit volume of rock It is obvious that the term Cv could also be called the apparent powder factor should the equation be written in the form, Cv = Q/W3 (lb per cubic unit). However, while the approach was ingenious** and the practical applications straightforward, their original, rather limited experimental work, along with certain assumptions, was questioned.

Jan 1, 1970

By P. E. Lenz

In Nevada, large deposits of diatomite were formed during the Miocene / Pliocene in deep, alkaline lakes. Associated sediments are predominately fine-grained lacustrine with varying fluvial-clastic layers. Tephra layers are common, and probably served as a source of soluble silica for the extensive diatom colonies. Four companies are currently producing diatomite from Nevada deposits. Nevada ranks second to California in annual domestic production. Nevada diatomite is used in filter aids, fillers, absorbents, catalyst supports, and many other products. Economics and mineral reserves indicate that diatomite production in Nevada will be significant well into the next century.

Jan 1, 1993

By J. D. Vincent

The Henderson mine site is located at Red Mountain on the eastern slope of the Rocky Mountains, approximately 50 miles west of Denver, Colorado. The mill site is on the west slope of the Rockies and mine and mill will be connected by an underground railroad. All designs were for a 30,000 ton per day molybdenite processing plant with provisions for future expansion up to 50,000 ton per day if required. This plan did not just happen, but slowly evolved over the course of about three and one-half years. Many plants cannot afford such a delay, but the Henderson project will take about 10 years from the time it was first discovered until production starts, and these 3 !1 years were well spent in determining the best possible plant site and flowsheet. This paper describes some of the problems and the decisions made in arriving at the final location and flowsheet. The paper does not go into the specific details of how protection of the environment went hand-in-hand with all other project considerations. This particular aspect of the planning has been well-reported on other occasions and considerable information on it is readily available.

Jan 1, 1972

By Thomas D. Henderson

Este capítulo presenta- un "caso histórico" de los pasos a dar para estimar IDS castes de capital y operativos para un concentrador típico de cobre porfirico de ± 9;070 toneladas métricas de producción diaria. El concentrador que se describe es hipotético, pero está basado en la experiencia propia y es, en efecto, una composición de varios proyectos reales. Las cifras utilizadas son ilustrativas solamente y no representan los castes reales de ningún lavadero en particular. Estas cifras son, sin embargo, representativas de los castes tipicos de molienda en un punto en el tiempo y son to suficientemente precisas coma para iIustrar los procedimientos de estimación de castes descriIos en este capítulo, No es posible publicar cifras reales y corrientes de los castes del lavadero y, en cualquier caso, las cifras de Ios castes reales pierden rápidamente su significación en Ia actual situación económica con los rápidos incrementos de las diversas partidas que configuran los castes. El trabajo está dividido en tres partes: (1) orden de la magnitud estimada, (2) estimación def estudio de viabilidad, y (3) comparación entre los castes estimados y los castes rea¬les. Con vistas a este trabajo supondremas que una mina tiene una propiedad minera explorada mediante perforación con testigos que refleja un yacimiento, ampliamente definido, como de unas 45,3 millones de toneladas métricas con una ley del d,6°/ de sulfuro de cobre, Esta compañia desea obtener primero una estimación del orden de magnitud de los costes (canto de los costes operativos como del capital) para determinar si la pertenencia garantiza más perforación y desmuestre de testigos. Suponiendo que esta evaluación económica obtenida utiIizando Ia orden de Ia magnitud de Ios costes sea favorable, sera a continuación requerido un estudio de viabilidad más preciso de los castes de capital y operativos. Seguidamente of recemas una descripción de los diferentes pasos dadospara desarrollar ]as costes del orden de primera magnitud y a continuación para los castes del estudio de viabilidad.

Jan 1, 1982