Search Documents

By Menglong Bian, Xiaotong Dong

Thermal damage is an urgent problem faced by deep mining. High-temperature rock mass, hot water and electromechanical equipment are the sources of the thermal damage. The increase in air temperature in mine tunnel is the result of fluid–solid coupling heat transfer from various heat sources. This paper takes a roadway with hot water and a mine car as the research object. Based on the Fluent, Static Structural and Steady-State Thermal modules in ANSYS, the thermal-fluid–structure coupling analysis in the roadway is carried out. It is found that the hot water has a significant effect on the thermal environment of the mine. Under the experimental parameters, the maximum heat flux density and equivalent elastic strain at the interface between the hot water and the rock are 9789.3 W/m2 and 0.00054532 m/m, respectively. The heat flux distribution in the rock area near the mine car does not change much, and the equivalent elastic strain value in this area is high. After the air is heated in the hot water area, the temperature curve changes gradually and then rises steadily. By changing the inlet air temperature parameter, it is found that the lower the inlet air temperature, the better the cooling effect, and the change of the inlet air temperature can change the air temperature field in the roadway as a whole. By changing the parameter of inlet air speed, it is found that higher wind speed brings better cooling effect, but with the increase in wind speed, the cooling effect of roadway thermal environment is very limited. When the wind speed increases from 5 m/s to 10 m/s, the air temperature of most measuring points drops by more than 2℃; when the wind speed increases from 15 m/s to 20 m/s, the air temperature of most measuring points drops below 0.7℃. After the wind speed reaches a certain value, the cooling effect of ventilation is very limited.

May 5, 2022

By Dennis N. Poffenroth

One concern of the Mine Safety and Health Administration is the structural integrity of steel wire ropes used on mine personnel hoists and elevators. Failure of such ropes has resulted in loss of life and property. Although thorough and regular visual examinations are performed, hoist ropes may still fail from undetected internal wear, corrosion, and broken wires. To complement visual examinations, nondestructive rope inspection techniques have been developed to determine deterioration and removal criteria. The techniques use electromagnetic and permanent-magnet test instruments designed by a Canadian firm. This paper describes the operating principles, field and laboratory testing of these nondestructive testing instruments, and discusses the feasibility of using this type of testing as a supplement to visual examination and destructive tests.

Jan 1, 1983

By J. L. Roll

The Surface Mining Control and Reclamation Act of 1977 (SMCRA) and the regulations promulgated for that "Act" have resulted in changes to surface mining operations in order to comply with the stringent federally enforced reclamation requirements for prime farmland. In many instances the operator has modified surface mining operations to meet the prime farmland requirements through changes to mining equipment operation, addition of new equipment targeted for reclamation or the use of totally different mining techniques. The major challenge to mine operators has been how to use existing mining equipment to meet the requirements of the "Act." Freeman United Coal Mining Company opened the first new large surface coal mine in Illinois following passage of the "Act." The Industry Mine, located near Macomb, Illinois started mining operations during March of 1982 and was required therefore, to meet all of the requirements of the "Act" including prime farmland restoration. At the Industry Mine a shovel and a cross-pit bucket wheel excavator (wheel) are used for overburden removal and the wheel is addition- ally utilized to assist in reclamation operations. The wheel mines the subsoil thereby elliminating scraper placement of that subsoil and the attendant compaction problems with scraper placed subsoil. The wheel is used to convey topsoil stock- piles from the highwall to the mined overburden in order to lessen scraper traffic and possible compaction on the graded overburden during top- soil removal and replacement. Close control of the operation of the wheel yields more uniform wheel spoil ridges which then require less grading prior to topsoil replacement.

Jan 1, 1986

By Boris CARO VARGAS, Bernard Theron

"In early 2014, Nicholson Construction Company was awarded, together with its tunneling sister company Bessac, the Norris Cut Miami Tunnel Project. The 2.5-meters diameter segmental lined tunnel, 1600-meters long, is aimed to replace the existing 54” force main connecting the Waste Water Treatment Plant (WTP) on Virginia Key to Fisher Island. To overcome project challenges such as the highly permeable limestone of the Fort Thomson Karstic Formation (one of the most permeable formation in the World), the project team has developed State of the Art solutions: The TBM was launched with pipe-jacking technique for the first 70-meters and then converted to segment erection mode. It allows substantial schedule savings and drastically reduces the size of the circular launching shaft. The TBM, jointly designed and manufactured by Bessac and Herrenknecht, can convert from slurry to EPB mode within a few minutes. The cutters can be replaced by wet divers thanks to an innovative application in the TBM industry. PRESENTATION OF THE PROJECT The aim of this project is to replace the existing 54-inch force main pipeline which transmitted all sewage collected from Miami Beach, Surfside, Bal Harbour, Bay Harbor, North Bay Village and Fisher Island to the Central District Wastewater Treatment Plant (CDWWTP) to Fisher Island. The existing pipeline consisted of pre-stressed concrete cylinder pipe which is in poor condition in a number of locations and could be subject to sudden failure. An adjacent portion of this existing force main under the Government Cut (North Fisher Island) has already been replaced as part of a previous design-build contract and involved the installation of a 60-inch diameter fiberglass-reinforced mortar pipe installed inside a micro-tunneled casing."

Jan 1, 2016

By A. R. Rule

As part of the Federal effort to help maintain an adequate supply of fertilizer minerals, the Bureau of Mines is conducting research to characterize complex, low-grade western phosphate rock and to develop methods for economic recovery of phosphate. The rock varies from soft, friable, altered phosphatic shale to hard, tightly cemented, unaltered phosphate rock. To supplement current beneficiation by sizing, a flotation procedure was devised that included depression of phosphate minerals with H2SiF6 and anionic flotation of carbonate minerals, followed immediately by cationic flotation of silicate minerals. Application of the procedure to several different ores resulted in phosphate concentrates that ranged from 28 to 31 pct P20S in grade and from 60 to 70 pct in phosphate recovery.

Jan 1, 1977

By Max Friedemann, Franziska Günther, Helmut Mischo

Ensuring adequate ventilation is a critical aspect of safety in underground mining operations. In small-scale mines in particular, key ventilation parameters such as temperature, humidity, and air velocity are often measured manually and only at infrequent intervals, typically using analog instruments. As a result, real-time monitoring of environmental changes, timely detection of hazardous situations, and demand-driven ventilation control are not feasible. This presentation discusses the selection and evaluation of modern digital ventilation measurement devices, including handheld instruments with digital data logging capabilities and continuously operating sensors with potential for real-time data transmission. The investigations focus on the challenges posed by underground environments with extremely high humidity levels, which can adversely affect sensor performance and electronic components. The results are based on testing conducted at the Research and Teaching Mine of TU Bergakademie Freiberg—an underground ore mine characterized by humidity levels exceeding 95%. Findings include assessments of measurement accuracy, reliability, and practical applicability under these demanding conditions.

Feb 22, 2026

By W. M. Colwell

When it comes to the analysis of gold bearing ore, there are literally dozens of variables that contribute to the final "true value" of a given sample. Initial sample selection, splitting size and method, inherent nugget gold, pulverization method, and analytical method variations are but a few. However, it seems that the inherent nugget gold particle is targeted as the primary reason for intra and inter-laboratory variations in assay. The following study will show that this is not always the case. A series of tests were undertaken for the Aurora Partnership-Aurora Project to solve inter-laboratory variations in the analyses of blasthole cuttings. Initial concern was centered on the probability that free gold occurrence was resulting in erratic results for the mine's cyanide shake assays and outside laboratory fire assays. Comparison of fire assay and cyanide shake assay was sporadically consistent with previously demonstrated extraction percentage for the cyanide method. The goal was to delineate the factors that ensure consistency in analyses; implement, where needed, Good Laboratory Practices; and reestablish acceptable analytical method correlation.

Jan 1, 1993

By F. W. Petersen

Slurry reactors are being used extensively throughout the chemical, biochemical and mineral processing industries. This paper describes the interaction between fine ore particles and granular porous adsorbents such as activated carbon and ion-exchange resins in a stirred tank reactor. Gold and silver cyanides were used as adsorbates to detect changes in the mass transfer characteristics of the adsorbents, which were ashed to determine the loading of ore particles. A simple kinetic model incorporating film diffusion, intrapanicle diffusion ~d the adsorption equilibrium, was used to interpret kinetic data and to estimate the effect of slurry conditions on the diffusion parameters. It was observed that the equilibrium loading of fines in the adsorbents was independent of their concentration in the slurry. Furthermore, the presence of these panicles inside an adsorbent decreases the effective diffusion of gold or silver cyanides into the adsorbent matrix. When fine suspended solids are present in the reactor, a decrease in the effective availability of the superficial surface of the pre-saturated adsorbent panicles for mass transfer from the liquid phase was observed. This newly defined surface availability factor was dependent on the concentration, panicle size, and the zeta potential of the fine particles in suspension.

Jan 1, 1993

By C. O. Lee

The Grand Isle Sulphur Mine is located in the Gulf of Mexico, approximately seven miles off the coast of Grand Isle, Jefferson Parish, Louisiana. The depth of water at this location is about 50 feet. The deposit is on acreage covered by oil, gas, and mineral leases which were originally issued in favor of Humble Oil & Refining Company by the State of Louisiana, and which were continued, maintained, and redesignated by the Department of the Interior of the United States, pursuant to Section 6(b) of the Outer Continental Shelf Lands Act. On September 19, 1956, Freeport Sulphur Company acquired from Humble Oil & Refining Company the sulphur rights underlying the tracts. This assignment was approved by the Secretary of the Interior on July 12, 1957. The Director, United States Geological Survey, approved Freeport Sulphur Company as Operator on July 31, 1957. Actual design began in September 1956; the first structural contract was let December 15, 1957, and offshore erection began in June 1958. The initial phase of construction will be completed and production started in early 1960. The estimated total cost of the project is $30,- 000,000, of which $8,000,000 is the extra cost for being in the Gulf of Mexico.

Jan 1, 1959

By R. R. Johnson

The Hama Mining Company owns and operates The Groveland Mine near Iron Mountain, in the Upper Peninsula of Michigan. The orebody is part of the Menominee Range of the Lake Superior District. The ore (generally known as Jasper taconite) contains an average of 35% iron ranging from 28% to 39% with an overall split of 60% magnetite and 40% hematite. The variations encountered throughout the orebody require a certain amount of blending to reduce feed changes to the mill. One of the variables which affects the crushers, as well as the mill, is the range of hardness which has a low of 7.9 and a high of 24.6 as measured by the Bond Twin pendulum impact and crushing technique. Reference is made to hardness only to point out its effect on crushing and wear rate variations. Over a period of time, these variables do, of course, average out. Mining of the low grade ore started in 1959 and has operated continuously to date. Preparation of the feed for conventional rod and ball mill grinding is accomplished by three stages of crushing. Reduction of crude ore is first passed through a 54 inch gyratory crusher; then through a secondary crusher; followed by two or three tertiary crushers in closed circuit with screens as production quotas require (Figure 1). Current demand to the crushers is about 5,200,000 tons of crude ore per year.

Jan 1, 1976

By J. P. Rider, T. W. Beck, J. A. Organiscak

"The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Mining Research Division (PMRD) has recently developed a series of models utilizing computational fluid dynamics (CFD) to study gas distribution around a continuous mining machine (CM) with various fan-powered flooded bed scrubber discharge configurations in an exhaust curtain working face. CFD models utilizing species transport model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The study illustrates the gas distribution in the slab (second) cut. The following scenarios are considered in this study: 100% of the discharge redirected back towards the face on the off-curtain side of the continuous miner; 100% of the discharge redirected back towards the face, but divided equally to both sides of the machine; and 15% of the discharge redirected toward the face on the off-curtain side of the machine, with 85% directed into the return. These models were compared to a model with a conventional scrubber discharge where air is directed away from the face into the return. The models were validated based on experimental data and accurately predicted sulfur hexafluoride (SF6) gas levels at four gas monitoring locations. One additional prediction model was simulated to consider a different scrubber discharge angle for the 100% redirected, equally divided case. This paper describes the validation of the models based on experimental data and the gas distribution results of the CFD models. INTRODUCTION To control methane gas and dust concentrations on continuous mining operations, it is important to provide sufficient quantity of fresh air from the end of tubing or curtain to the active face. In this region, operating machine-mounted water sprays and fan-powered, flooded bed scrubbers can significantly increase the amount of airflow reaching the face [1-3]. However, when an entry is large, especially in higher coal seams, the water spray configuration and the scrubber capacity may not be adequate to maintain sufficient forward airflow to confine the dust cloud to the face. Dust can roll back toward the machine operator as a result [4]. Currently, several coal mines having negligible gas emissions in higher coal seams (2.4 to 3.0 m [8 to 10ft.] thick) with exhaust tubing systems redirect the scrubber discharge back towards the face in an effort to improve dust collection. NIOSH studied the redirected scrubber exhaust techniques for dust and gas control in a full scale CM gallery to assess its potential for industry-wide application [5]. For a CM face, previous studies have concluded that the behavior of gas and respirable dust is a complex process. The distribution/dispersion and transport of gas and respirable dust after they are liberated at the face are governed mainly by their mass properties, the movement pattern of the ventilation air, and interactions with the mining machine and water droplets created by the external water spray systems used for dust control [6-10]. To understand these behaviors in a complex CM environment and to evaluate the effectiveness of various control techniques, numerical modeling has become a necessary supplement to laboratory experiments and field studies."

Jan 1, 2017

By R. L. Wiegel

Some of the mineral deposits that are being processed today, and especially those expected to be processed in the future, have relatively low compositions of the valuable mineral. With these low-grade ores, it is necessary to be able to design processes that are sufficiently low-cost to permit exploitation. One approach to minimizing the capital and operating costs for these processes is to use the capabilities of computer process simulation in the design phase of development, to make important technical and economic decisions regarding the evaluation of alternative process flow schemes, the selection of equipment and the choice of operating conditions. There are mathematical simulation models for most mineral processing operations, including several each for size reduction, size classification and mineral separations. To be able to tie these individual operating models together in an integrated mineral process simulation, however, it is important, in fact in some cases essential, that there be a model which describes how the mineral system responds to size reduction in making the liberated valuable and waste mineral particles available for concentration or rejection operations and the locked particles available for possible recirculation. This, then, is the role played by the mineral liberation model, showing the relationship between particle size, quantity and composition throughout the process.

Jan 1, 2011

By H. J. van Antwerpen

AngloGold Ashanti operates the world`s deepest mine, Mponeng gold mine, in South Africa. A vast refrigeration and ventilation system provides acceptable working conditions 3800m below surface at 60°C rock temperature. In such a system, optimisation and assessment of modifications becomes very difficult. With that in mind, a research project was launched to determine whether recently developed system simulation technology can be applied to a mine as vast and complex as Mponeng. Using the techniques and methods as implemented in FLOWNEX software, it was indeed proven to be possible to do a mine-wide combined simulation of compressed air flow, ventilation air psychrometry and refrigeration water systems. Interactions between the various streams included heat transfer, pressure drop, evaporation and condensation. The simulation model was used in a parametric study to test various water flow and temperature operating points for the refrigeration system. It was found that, given current limitations, the mine refrigeration system is running fairly close to optimal but with some opportunities for improvement. The simulation model also provided useful insight for future changes or extensions to the system.

Feb 23, 2014

By John D. Smart, John W. Sager

The following paper is an evaluation of the instrumentation programs on recent Corps of Engineers tunneling projects. The authors have first-hand knowledge of the NORAD Cheyenne Mountain Complex (NCMC) Expansion Project. Information on the other projects comes from conversations with those directly involved in the instrumentation programs and from referenced reports. The specific objectives of this paper are: (1) to state the purposes of the instrumentation programs, (2) to discuss the benefits gained from the instrumentation, and (3) to present conclusions from this study that will provide guidance to those planning instrumentation on future projects. Presentation of detailed descriptions of the projects and instrumentation data is limited to that necessary to the accomplishment of the above objectives. NCMC EXPANSION PROJECT The NCMC is located at a depth of approximately 800 feet in Cheyenne Mountain near Colorado Springs, Colorado. For the current expansion project new chambers were mined to accommodate a new diesel power plant and associated cooling and air handling equipment. During 1971 some 55,000 yd3 of granite were mined through existing access tunnels for this expansion. A model of the new excavation is shown in Figure 1. The light shaded areas are new openings, and the dark areas are portions of the existing operating complex. The large chamber to the right is the power plant chamber and has a span of 67 ft, a height of 50 ft, and a length of 172 ft. The other large chamber on the lower level is the cooling tower chamber and has a span of 38 ft, a height of 45 ft and a length of 185 ft. The small chamber on the upper level has a span of 20 ft and is 27 ft high and 140 ft long. Other major excavations are the 18 ft diam air tunnel

Jan 1, 1997

By H. Dreissen

Upgrading of low-concentration ores is of growing importance today. The Heavy Medium Cyclone Process, thanks to strong centrifugal forces, effectively separates particles varying only slightly in specific gravity but widely in size. The paper discusses the separation efficiency, the method of assessing that efficiency, and the influence of such factors as medium solids. The operating results of nine heavy medium cyclone plants handling following minerals are reported: barite, wolfram, iron, magnesite, diamond, lead-zinc, fluorspar, rocksalt potash. Highlighted are an improved recovery system for heavy medium and some other developments, such as techniques for separation down to 0.1mm and the application in the field of recycling.

Jan 1, 1980

By J. A. Pontius

The Cresson Deposit is located in central Colorado within the historic Cripple Creek Mining District. The deposit has moved from its initial discovery in 1990 to full production in less than five years (current reserve nearly two million ounces). This accomplishment required a great deal of cooperative teamwork between the exploration, development, permitting and corporate groups. Nowhere was this cooperation more evident than in the construction of the geologic block model. The detailed modeling of gold and its metallurgical characteristics formed the foundation upon which critical financial and design decisions were based.

Jan 1, 1995

By A. K. Gangopadhyay

This paper discusses the effect of grinding media composition, mineral type and slurry environment on the wear rate of various grinding media (balls). Sufficient wear data have been obtained and correlated with the modes of wear determined from examination of the ball surfaces using scanning electron microscopy. Five modes of wear have been identified to be operative under certain slurry conditions for the various ball compositions studied.

Jan 1, 1984

By I. Casasbuenas, K. A. Nguyen, E. I. Ngoma, H. Kim, D. Borja, J. H. Park, R. A. Silva, S. Choi

"This study aimed to determine the optimum operating parameters of a continuous bioleaching system to leach arsenic (As) from mine tailings using a mixed mesophilic bacterial culture. The microbial consortium, previously adapted for effective growth at high pulp density and metal concentrations, was mainly composed of Leptospirillum ferriphilum, and Acidithiobacillus caldus. The mine tailings, collected from the Janggun mine (South Korea) contained 11% (w/w) of As. The tests were performed in a laboratory-scale unit composed of three reactors connected in series following a cascade configuration. Agitation speed, air supply, solid concentration, residence time and temperature were systematically optimized by assessing the leaching activity. Several parameters were monitored on a daily basis, including the As released into solution, iron oxidation rates, pH, cell concentration, dissolved oxygen and redox potential. Overall, improvement of oxygen transfer, by optimizing the agitation speed and air supply, presented the most tangible impact on the leaching performance. The highest As leaching efficiency observed in this study was 82%, which supports the feasibility of the process. INTRODUCTION Worldwide, around of 65 billion tons of mine tailings are produced every year (Jones & Boger, 2012). These materials comprise the waste minerals produced after ore beneficiation. Mine tailings usually contain heavy metals (e.g., Cobalt (Co), Lead (Pb), Zinc (Zn) and Arsenic (As) (Falagán, Grail, & Johnson, 2016; Nguyen, Lee, Park, & Lee, 2014). The exposure of these materials to the environment can produce serious health damage and environmental degradation (Martin, Dowling, Pearce, Sillitoe, & Florentine, 2014). Mine tailings management represents a major issue in South Korea. There are more than 1,000 abandoned mines containing stockpiled mine tailings within the territory (Choi, Park, Hong, Park, & Kim, 2013; Kim, Kim, Ahn, Ko, & Lee, 2005; Lee, Lee, & Kim, 1998). These tailings comprise high concentration of arsenic. Therefore, the Korean Government has directed its efforts to developing eco-friendly technologies, for the arsenic detoxification of mine tailings Continuous bioleaching is explored as a remediation technology (Borja et al., 2016). The present study aimed to develop a mixed mesophilic bacterial culture for optimal growth at high metal and solid concentration; and optimize the operating conditions of a continuous bioleaching unit. This investigation forms part of a larger study aimed to develop a bioleaching technique to treat Janggun mine tailings (Borja et al., 2017; Ngoma et al., 2017)."

Jan 1, 2018

By Stephen J. Swan

Feed-forward control (i.e. the forward flow of information in a control system ) is a simple and flexible approach to over-all control of a ball mill-rake classifier grinding circuit. The system described here uses mill power, feed rate, mill dilution water flow rate, and classifier dilution water flow rate only, to control mill load, throughput, mill solids, and classifier solids as well as classifier overflow grind. The mill load is controlled by a simple feed-back control loop, while mill solids and overflow grind are controlled within close limits by a unique non-linear feed-forward water control system. In effect the control follows a limited mathematical model of the grinding circuit. The configuration minimizes deviations in overflow grind due to changing ore conditions, but since it is open-loop, and the model is not complete, it is affected by changes in total ball charge and liner wear. These effects are fortunately gradual, and changes in the grind can usually be kept to within ± 1% of a target continuously for several days without adjustment. Control adjustments are made with feed-back from laboratory composites. This control system has won enthusiastic operator acceptance; it is easily started up and shut down; grind-outs have been eliminated along with flotation machine flooding and mill spills. Standard measurements and components are used throughout providing a trouble-free system design at a moderate cost.

Jan 1, 1970

By R. W. Waytulonis

This paper is an update of the activities of the U.S. Bureau of Mines, other government agencies, and the automotive and truck industry concerning diesel emission control. Enacted and proposed regulations from the U.S. Mine Safety and Health Administration (MSHA) and developments in diesel emission control are presented in terms of their impact on underground coal, metal, and nonmetal mines. Mine air quality regulations proposed by MSHA may require the underground mining industry to comply with new standards. Some mines may be required to take additional actions to meet new diesel particulate and lower nitrogen dioxide exposure standards; however, the mining industry is in a position to benefit from emission controls developed for the on-highway diesel engine market. The U.S. Environmental Protection Agency (EPA) has enacted regulations to reduce emissions from on-highway diesel trucks and buses. Engine manufacturers have responded by developing cleaner burning engines. Fuel producers have responded by providing cleaner burning reformulated diesel fuel, and exhaust aftertreatment devices have been developed to provide additional emissions reductions. Bureau research and development projects seek to determine the advantages of using modern engines and fuels, and to evaluate the efficacy of new exhaust control devices on mining machines. It appears that the diesel engine will continue to be a practical power source for use in confined environments because no other available power source is as mobile and efficient.

Jan 1, 1993