Search Documents

By J. F. Power

Returning the original soil material to the surface of smoothed mine spoils is n practical means of restoring agricultural productivity. Research has established that high-sodium spoils in North Dakota (a) must be covered with about 70 cm of soil material to achieve maximum production; (b) topsoil must be segregated and spread separately from subsoil; (c) potential production depends on the quality of the soil material returned; and (d) erosion and upward salt movement must be controlled for sustained production. Erosion is best controlled by reducing final grades as much as possible during the smoothing process followed by prompt establishment of vegetation. Almost half the nation's cool reserves are in the Northern Great Plains underlying several million hectares of agricultural land. Social pressures to return mined land to agriculture or other productive uses have resulted in recent enactment of state and federal legislation, which is intended to restore productivity to disturbed areas. All such legislation relating to the Northern Great Plains has stipulated that useable soil material be saved and returned to mined land after spoils are smoothed. This requirement immediately raises questions as to how much soil material is needed, what criteria are important in defining useable soil material, how is the soil material to be handled in the earth-moving operations involved, and how can replaced soil material be maintained and revegetation. Scientists at the USDA Northern Great Plains Research Center at Mandan, North Dakota have conducted research on the reclamation of disturbed lands since 1970. Initially this research was designed to identify and characterize those physical and chemical properties of spoils that are most restrictive to plant growth (1). Basically, they found that any properties of spoils that reduced the efficiency of storage and utilization of the limited precipitation received adversely affected plant growth. Thus, in the Northern Plains, revegetation of mined land was found to depend upon the management of factors affecting the availability of water to plants - the same as on unmined land. After the major problems in revegetation were identified, technologies were developed to circumvent the effects of the growth-limiting factors (2). Basically two approaches were identified by which plant growth-restricting properties of spoils could be corrected: (a) various amendments (gypsum, sulfur, Fertilizers, mulches, calcium chloride, etc.) could be applied to spoils to improve their ability to conserve precipitation and provide water for plant growth; or (b) undesirable spoils could be covered with suitable soil materials to reduce or alleviate adverse effects. The latter approach appeared to be more feasible in most instances And is the approach specified in current legislation. The remainder of this paper discusses research on the use of roil materials returned to spoils and summarizes the information obtained.

Jan 1, 1978

Large deposits of eudialyte, a low grade zirconium bearing mineral, occur on the Southern Coast of Greenland in the Ilimaussaq intrusion. Various processes were tested in the laboratory to recover eudialyte from these ores, including flotation, leaching, gravity and magnetic separation. A combination of dry and wet magnetic separations has the advantage of simplicity and the least environmental impact for the location. This paper summarizes the results of laboratory testwork to develop a two-stage treatment process to recover the eudialyte by magnetic separation.

Jan 1, 1993

By S. N. Gurulaxmi, Veerendra Singh

The abstract discusses the increasing consumption of manganese ores and the need to utilize low-grade ores and rejects. The study focuses on developing a low-cost process using a cupola furnace to recover manganese values from these resources. The process involves smelting ore blends to produce high MnO slag and pig iron. The study investigates various factors to improve iron reduction and separation from MnO-bearing slag. The results show that the process can produce slag with MnO > 35% and Fe(t) < 5% using low-grade Mn ores. The process also achieves Fe reduction between 50 and 70%. The cupola furnace offers advantages like low cost and ease of operation, making it suitable for processing low-grade ores and rejects to produce synthetic MnO-enriched products for various industries.

Apr 1, 2022

By R. Duckett, D. Salisbury, R. Dorey

The Kennecott Ridgeway Mine in South Carolina is scheduled to complete mining and ore processing in the last quarter of 1999. Tailings are disposed in a 300 acre, lined tailings impoundment. To facilitate closure and reclamation, modification of the tailings impoundment operation has been adopted. Mining involved the sequenced development of two open pits. In 1996 mining of the South Pit was completed and backfilling of the pit with waste rock from the North Pit was initiated and will continue until mining ceases. Both pits will be reclaimed as fresh water lakes. This paper presents the physical, geochemical and hydrogeochemical evaluation of the operational and post operational management of the project. Comparison of the operational monitoring data against predicted performance are reviewed.

Jan 1, 1999

By C. H. Grant

The Dew Chemical Company has been engaged in explosives research since 1953. The incentive for this research was based on the desire to find additional markets and uses for magnesium metal of which Dow is a heavy producer. The thermodynamic calculations for explosives incorporating light metals indicate energies approximately twice that of non-metallized explosives currently being used. Early in 1960, we acquired additional patent rights from independent inventors and decided to set up a development station at Virginia, Minnesota, to conduct a commercial testing and market evaluation program with this new product. The actual manufacturing of the explosive was to take place in the bore holes. Due to the complexities involved in controlling the manufacture of the explosive in the bore hole, performance was sometimes in doubt. Furthermore, our experience indicated that the metallized explosive systems could not be evaluated by the standard laboratory methods then being used, and it was necessary for us to look for more suitable research methods. Tests were conducted on several known methods for explosive evaluation. The most promising were the Navy underwater method for energy evaluation, and a modified Livingston crater method intended to compare explosive performance in rock. After shooting over two thousand charges of eight to 60 pounds under water and in taconites and granites with many types of explosives, we have developed a metallized explosive which is now being manufactured at a pilot plant in Virginia, Minnesota, and is being evaluated commercially.

Jan 1, 1963

By Alireza Kamrani, Yashar Pourrahimian, Hooman Askari-Nasab

In-pit crushing and conveying (IPCC) is an option to decrease the enormous operating costs that a truck shovel can introduce in an open-pit mine. Finding the best locations for the IPCC over the mine life will impose a new set of requirements for the mine planning. Through a two-step mathematical programming model alongside the road network, this method finds the optimal in-pit crusher locations and relocation times first and then optimizes the long-term mine schedule. The model is verified by a real mine. The results show that the truck travel time could be reduced by 500% and the discounted cash flow increased by 8% with an optimized schedule considering the crusher placement.

Jun 25, 2023

By E. Watkins, S. J. SCHATZEL, K M. AJAYI, V. Gangrade, Z. Khademian

A stochastic discrete fracture network (DFN) model is developed based on mine site core log data to predict the horizontal and vertical permeabilities from the surface to the top of the caved zone at a longwall mining site in southwestern Pennsylvania. One hundred DFN realizations were generated to determine permeabilities for the isolated zone over an abutment pillar after mining the second panel. The results from this study show that the vertical and horizontal permeabilities from the DFN model agree closely with field measurements, which indicates that the resultant permeability obtained from the field measurements is representative of the predicted permeabilities. With this agreement, the aperture data for other zones of the mine could be obtained from the geomechanical model — specifically, for the fractured zone over the gob. Based on the successful validation of this model, this model could be further developed to predict the permeability of the fractured zone over the gob with fracture aperture obtained from the geomechanical analysis. This will complete the fracture characterization of the overburden, which could be used to predict potential shale gas flow to the mine in the event of a breach. This prediction could provide information on the associated risk of a casing breach and determination of methods to proactively prevent such an occurrence.

Feb 1, 2023

By Michael J. Miller

In the design of a modem mill, a stockpile storage system for raw and/or semi-processed ore has become almost indispensable. This paper discusses the benefits of such stockpile storage as well as the various types of belt conveyor stockpiling units available. Particular attention is given to large radial stackers since they offer the greatest flexibility. Stacker control systems and accessory equipment are briefly discussed. Various alternative reclaiming arrangements for stockpiles are reviewed and a discussion of the advantages and drawbacks of each arrangement is included.

Jan 1, 1979

By B. DANIEL MARJAVAARA, I. A. SOFIA LARSSON, ANNA-LENA LJUNG

The flow field and coal combustion process in a pilot-scale iron ore pelletizing kiln is simulated using a computational fluid dynamics (CFD) model. The objective of the work is to investigate how the thermal effects from the flame affect the flow field. As expected, the combustion process with the resulting temperature rise and volume expansion leads to an increase of the velocity in the kiln. Apart from that, the overall flow field looks similar regardless of whether combustion is present or not. The flow field though affects the combustion process by controlling the mixing rates of fuel and air, governing the flame propagation. This shows the importance of correctly predicting the flow field in this type of kiln, with a large amount of process gas circulating, in order to optimize the combustion process. The results also justify the use of down-scaled, geometrically similar, water models to investigate kiln aerodynamics in general and mixing properties in particular. Even if the heat release from the flame is neglected, valuable conclusions regarding the flow field can still be drawn.

Apr 20, 2021

Application of flotation for the removal of hydrophobic compounds from soils was studied. Bench scale flotation tests were conducted on artificially contaminated soil, using both conventional mechanically agitated machine and flotation column. Flotation parameters tested include surfactant collector type, conditioning time, flotation time, surfactant dosage, pulp pH, solid/liquid ratio in conditioning and pulp temperature. It is found that with conventional flotation 74% removal of the contaminant was achieved from soil particles in the range of 75-830 µm; with column flotation up to 80% of oil could be removed from the 250-830 µm soil fraction, and 65% from the 75-830 µm fraction. Flotation was found to have considerable potential for cleaning up contaminated soils.

Jan 1, 1998

By David J. Boron

The United States has the largest total (364 billion metric tons) and recoverable (182 billion metric tons) coal reserves in the world.1 However, progressive coal utilization in this country has been hampered by environmental constraints, such as restrictions on sulfur dioxide, nitrogen oxides, and particulate emissions. New technologies are being pursued both to appease these environmental concerns and improve economic performance and process efficiency. These technologies, however, have not reached the level of effectiveness required for optimum operation. If more stringent emission standards are imposed, it is likely that the coal industry, and the industrial and utility sectors will look increasingly toward the successful development of new and advanced coal cleaning technologies in order to continue and promote the use of coal in this country. The EPA New Source Performance Standards In 1979, the Environmental Protection Agency in response to the amendments to the Clean Air Act of 1977 issued new source performance standards (NSPS) for utility and industrial boilers. The NSPS set emission standards for sulfur dioxide, nitrogen oxides, and particulates affecting boilers of 250 MM Btu per hour heat input or &apos;greater that started construction after September 1978. Plants starting construction or in operation before September 1978 remained subject to the provisions of the regulations promulgated in 1971, i.e., SO2 emissions of 1.2 15/MM Btu. The NSPS for SO2 emissions provides a sliding scale for SO2 reduction depending on the sulfur content of the run-of-mine coal, with an upper limit of 1.2 lb of SO2 per million Btu and a minimum emission level based on 70% SO2 removal. Table 1 summarizes the EPA NSPS for SO2 emission standards.

Jan 1, 1983

By Kenneth N. Han

The effect of anions such as sulfate, chloride, and nitrate on the solubility of rare earth element-bearing phosphates and fluorocarbonates has been examined using relevant thermodynamic data. The study has found that these anions have significant influences on the overall dissolution of rare earth elements (REEs) from various sources in the aqueous media. The thermodynamic calculations in this study have indicated that the speciation of REEs with the anions tends to increase the overall solubility of the REE-bearing minerals. However, in some cases, strong precipitation of REEs with some of these anions causes an adverse effect on the solubility of these elements. It has been found that sulfate ion has the most pronounced effect on the solubility compared to nitrate and chloride, in which the latter two acids exhibited almost identical results. The calculated results have indicated that REE-oxide (hydrated) is the easiest compound to dissolve, followed by carbonate, phosphate, fluoride, sulfate, fluoro-carbonate, and oxalate in that order.

By T. R. Ellis

Many appraisers/valuers believe that the only valuation method available within the cost approach category for real property appraisal is the depreciated replacement cost method. Some valuation and financial reporting standards setters also believe the same. This paper introduces the minerals appraiser to a number of useful methods for mineral property appraisal that are based primarily on the principle of contribution to value, the predominant economic principle in the cost approach. Most of these cost approach methods discussed are primarily for use in valuation of exploration tracts and resource properties that have no defined reserves. However, the powerful rural cost method can be used to calculate the contribution of categories of resources, reserves and other property components to the value of a mineral property. This method can be applied to mineral properties at all stages of development, including producing properties. The author reasons that standards and regulations pertaining to real property valuation should be modified, and underlying principles should be expanded, so as not to inhibit appropriate application of these cost approach methods.

Jan 1, 2011

By Jack M. Campbell

The regulatory process by which governmental authorities acknowledge and, in turn, permit the location, construction, and operation of large scale energy-related facilities has become extremely detailed in recent years. One example of the detail that is entailed in the regulatory process is the number of permits that must be acquired by operators prior to the construction and operation of energy-related facilities. It has been estimated, for example, that 75 permits are required prior to the opening of a new coal mine in Pennsylvania while 50 are required in Kentucky. From the perspective of facility owners and operators the regulatory process often appears overly complex and may be perceived as a constraint to the corporate decision making process. From the perspective of those responsible for administering regulations, the process is perceived as a mans by which public desires - pursuant to social objectives such as environmental protection and occupational safety - can be achieved. As a result of conflicting organizational interests, the clash between energy facility owners and operators and their regulators appears to be inevitable. Furthermore, the resolution of this conflict lies in the tradeoff between objectives and the costs of regulation. The balance of objectives and costs is a subject of the political process and not a topic of consideration in this paper. This paper is concerned with the actual administration of regulations, that is, the implementation of that which arises from the interplay of organizational interests. The paper assumes that environmental control laws will not likely be repealed, that regulations to implement the intent of these laws are here to stay and thus the paper seeks to assess how regulations are administered at various levels of government pursuant to objectives. The paper hypothesizes that the administration of objectives (or policy) has an impact on decision making which affects energy facility decision; making while recognizing the fact that regulatory policy cannot be totally divorced from administration, this paper proceeds

Jan 1, 1977

By James S. Browning

Extensive deposits of kyanite occur in the southeastern United States, The reserves of these deposits, if developed, are adequate to supply the United States with 35-mesh kyanite concentrate:; for many years at the present-rate of consumption, According to Espenshade and Potter,1 the kyanite-quartz rock type deposits in this area contain about 100 million tons of ore averaging 10 to 30 percent kyanite. The tonnage of kyanite-bearing gneiss and schist is, much larger than the tonnage of kyanite-quartz rock, but the kyanite gneiss and schist are appreciably lower in grade. The largest deposits of kyanite-quartz rock are in the Farmville district, Virginia, and Kings Mountain district, North Carolina South Carolina, and at Graves Mountain, Georgia. Of the known deposits, only four were being mined for kyanite in 1967. These deposits are near Farmville and Dillwyn, Va., Clover S. C., and Washington, Ga. Production of kyanite and synthetic mullite increased substantially in 1965.2 Output of, domestic kyanite concentrate increased by 14 percent in 1965, establishing a record high for the fifth consecutive year. Estimated annual consumption of kyanite minerals and synthetic mullite was in excess of 100,000 tons. The manufacture of mulatto refractories accounts for most of the kyanite minerals consumed annually, but non-refractory uses are expanding.3 Most mullite refractories are used as furnace linings in metallurgical and glass manufacturing furnaces. The remainder is used largely for kilns, kiln furniture, and saggers by the ceramic industry. Small quantities of kyanite without calcination are used as a source of alumina in the manufacture of glass, electrical and chemical, porcelain, pyrometer tubes, and in the form of kyanite concentrate to increase the alumina content of fireclays. Kyanite is used to improve workability, increase strength, and to compensate for firing shrinkage in floor and wall tile and other ceramic products.

Jan 1, 1968

By Shailendra Chawla, Ashok Jaiswal, Sonu

Side spalling/skin failure occurs due to the high-induced stress in underground structures. In such cases, rock bolting or other support systems are being used to control the skin failure or spalling of the pillar. The nature of these support systems is passive, which acts during the deformation. These support systems restrict the displacement considerably of the side/or roof surface of the excavation. Ultimately, it improves the stability of the structure because of the increment in residual strength of rock mass. It is noted that these passive support systems give very low confinement in the range of 0–0.015 MPa at the onset of failure. As the level of confinement will be very low and dependent with progress of failure, triaxial test was not found practically suitable. Thus, an alternative procedure of testing has been proposed. In the procedure, sides of sample have been restricted little bit by using adhesive tape. It provides the limited boundness on the lateral direction (LBLD) of rock specimen. The uniaxial compression strength (UCS) test has been performed on 30 numbers of cylindrical rock specimens using the servo-controlled stiff testing machine. Specifically, two rock types (medium-coarse–grained and coarse-grained rocks) were studied in terms of stress–strain behaviour so that a full residual strength envelope for each specimen was obtained. This study reveals that the residual strength of limited confined rock specimens has been significantly increased as compared to unconfined rock for both groups of rock types. The average residual strength of LBLD specimens of fine-grained rock and medium coarse-grained rock has been increased around 12 times, and five times as compared to unconfined rock, respectively. The average peak strength of LBLD rock specimens has been increased in the range of 30.5 to 48.6% for coarse-grained rock. The results of this study have been presented in terms of peak strength, residual strength and Young’s modulus of rock, and the post-peak failure behaviour of rock specimens was also critically analysed through a stress–strain curve.

Mar 21, 2024

By S. Acar

"In recent years the gold mining industry has been challenged by declining metal prices as well as having to treat ores that have low grades and are refractory in nature. Many factors must be considered when metallurgical studies are designed to develop process design criteria for these type of ores. These factors are mostly related to the mineralogical and chemical compositions of the ores, the geological setting of the deposit and how the ore/waste will be mined, such as whether openpit or underground, the mine schedule, and the mine fleet type and capacity. The purpose of this paper is to provide an experience-based practical approach to how to select and characterize test samples as well as devise process development metallurgical studies for both oxide and refractory gold ores, and to provide insight into some of the matters that might go wrong during the course of the studies. This paper is intended as both a guide for someone new to the field and also as a reminder for those familiar with the field. IntroductionThe recent decline in ore grades and metal prices have challenged mining companies to reduce capital and operating costs associated with developing new mineral resources. In some cases, metallurgical studies have been sacrificed to prevent cost overruns resulting in inadequate mineralogical, chemical and metallurgical characterization. Consequences have included longer construction schedules, higher initial and working capital, higher operating costs and less than desirable plant performance (Whincup, 2010; Torres, Chaves and Meech, 1999).Mineralogy, geology, mining type and sequence, and the metallurgy of an orebody will determine the process development metallurgical study requirements and eventual process plant design. Therefore, once the geologist has an early indication of a prospective orebody, geologists, metallurgists, mining engineers, and social and environmental responsibility scientists should convene and devise a plan on how to exploit the orebody economically (Lunt, Ritchie and Fleay, 1997).Geologists may find a prospective orebody solely based on grade. However, if the orebody cannot be mined and processed economically, then it is deemed not to be a deposit. An example of this could be a refractory gold deposit, either sulfidic, carbonaceous or siliceous refractory or any combination of those, that may not be mined and processed economically due to reasons such as the physical location of the deposit, depth of the ore lode, or social and environmental concerns. Therefore, an early collaboration between all disciplines must be established.Each orebody may have its own unique mineralogical, geological and chemical characteristics (Guresin et al., 2012). These unique characteristics should be effectively sampled to reduce risks associated with process design and engineering efforts for the process development metallurgical studies. If the sample or samples are not representative of these unique characteristics, then the studies performed will be pointless. The project metallurgist in charge of conducting metallurgical studies should also possess general geology, mineralogy and mine engineering knowledge. Recommended readings are a book on understanding mineral deposits by Misra (2000) and articles on heap leach development by Scheffel (2014a and 2014b)."

Jan 1, 2016

By E. J. Mayhew

Bentonite and newly discovered deposits of sepiolite, saponite, and hectorite are now being processed and marketed from the Amargosa Valley of Nevada. All of these deposits are large. The bentonite has been known for decades and is the whitest known. The only other sepiolite deposit is in Spain. The only other commercial hectorite deposit is at Hector, California. No other saponite deposit is known. All the components except bentonite are hydrous magnesium silicates. The bentonite is mixed layer Na-Ca. All the materials have characteristics unique to their locale and type, such as high yield point for drilling muds and liquid suspending agents. The sepiolite has geothermal stability. Figure 1.

Jan 1, 1979

By David Crouthamel, Raymond Henn

"The need to fill the void space or annulus created between an excavated tunnel or shaft and the final lining system has long been a requirement in underground construction. Most of those types of voids are created as a result of employing the two pass tunneling lining method. Filling of this void is called backfilling. For many years the materials used as backfill were primarily reinforced and non-reinforced concrete, sanded grout, neat cement grout, or blown-in sand/pea gravel. However, in the past 20 years the use of cellular grouts/cellular concrete as the backfill material has greatly increased. Most cellular grout is made of a mixture of water, Portland cement (with or without the addition of fly ash), a foaming agent and admixtures such as a water-reducer or superplasticizer.It is the authors’ preference to use the term cellular grout as opposed to cellular concrete since by ACI Concrete Terminology an ACI Standard (ACI CT 13), concrete contains aggregates. Normally cellular grout does not contain sand (finite aggregate), but almost never contain course aggregates.The authors believe there are several reasons for this increased use of cellular grout as backfill, such as:• The increase utilization of the various trenchless tunneling methods. Tunnels constructed using trenchless method tend to be smaller in size, excavated diameter or cross sectional area. Making man-entry for placing backfill from inside the secondary liner, utilizing pre-installed grout posts, more difficult if not impossible. It is these workspace restrictions that are the drivers as to when to utilize grout ports installed during the pipe/liner fabrication versus grout delivery pipes installed within the void/annulus space.• The ability of cellular backfills to be pumped and flow longer distances.• The unit weight of cellular grouts can be controlled by mix design and generally can range from 560 Kg/m3 (35 lbs/CF) to 1040 Kg/m3 (65 lbs/CF)."

Jan 12, 2017

By Eric R. Braun

Ore reserves in the Republic mining district were nearly exhausted in 1984 when hole D-54 intersected a vein twenty- eight feet in drill width averaging 1.57 opt gold and 11.95 opt silver below post-mineral lake beds. The discovery area, termed "Golden Promise", has announced proven and probable ore reserves of approximately 372,000 tons averaging 1.0 opt gold and 4.5 opt silver, and drilling indicates another 756,000 tons of mineralized material containing 0.37 opt gold and 1.4 opt silver (Hecla fourth quarter 1986 report). This paper describes new geological interpretations made as part of a district research study sponsored by Hecla Mining Co., which led to the D-54 discovery. Important new geological concepts include: 1) re-interpretation of the volcanic stratigraphy of the district and recognition of a suite of pyroclastic rocks that are unique to the Republic graben, 2) identification of disseminated subaerial mineralization at a paleosurface that corresponds to the newly described upper contact of the Sanpoil Volcanics, 3) recognition that epithermal veins have a maximum productive vertical range of 0-500 meters, measured from the paleosurface, and 4) veins exhibit visual and geochemical vertical zoning within the productive zone with highest gold occurring at an optimal depth, which is interpreted as the average depth of hydrothermal boiling.

Jan 1, 1987