Search Documents

By Henry J. Schwellenbach

The New York Trap Rock Corporation has four plants located along the Hudson River, all within 70 miles of New York City. The company produces crushed stone for use as construction aggregate, with a total annual production amounting to 6 million tons. The crushed stone is moved to markets in metropolitan New York, New Jersey and Long island areas by water transportation. There are daily deliveries of approximately 35 scowloads to the market area. Its customers are contractors with ready-mixed concrete and asphalt plants located on the water, where the aggregate is unloaded for its ultimate use. For a number of years capital equipment was replaced only when the current operating machinery was no longer serviceable, or when' a need was apparent for a different type of equipment. There was no particular regard for efficiency or for operating and maintenance costs. Such lack of system often resulted in the emergency purchase of equipment which was later found to be unsuitable for the job. A few years ago it became apparent that a systematic procedure was necessary. After evaluation of several systems, an individualized plan was evolved from the basic pattern developed by the Machinery and Allied Products Institute. The system adopted by New York Trap Rock has proved wholly satisfactory.

Jan 1, 1959

By S. A. Sanderson

The last two decades have witnessed the resurgence in popularity of a century old tool for shaping laws and public policy – the ballot initiative. In recent years, anti-mining special interests have used the initiative process to secure voter approval of measures to ban modern surface mining for gold and silver. In November 1998, voters in Montana approved such a measure1 – the effects of which have been devastating to the mining industry in that state. In November 1999, anti-mining groups sought to place a nearly identical provision on the general election ballot in Colorado. They did not succeed, but the battle over mining’s future continues in the most important forum of all – the court of public opinion. The Colorado measure failed, in large part, because its proponents failed to convey a positive environmental theme. The mining industry also exercised early-on the rights available under state law for administrative and judicial review of the initiative, instead of relying upon the limited relief that would have been available had it waited until after the secretary of state approved the measure for the November election ballot. This article will summarize the ballot initiative process in Colorado and the proceedings that took place over Initiative No. 215.

Jan 1, 2001

By J. A. Barsin

Stationary air pollutant sources established prior to the New Source Performance Standard (NSPS) are not, at present, subject to federal emissions regulations. However, proposed legislation could require many existing stationary sources to reduce emissions. This paper will report upon the laboratory work undertaken to date by B&W to commercialize a limestone system for sulfur capture both in pulverized coal and cyclone coal-fired utility boilers. Updates will be provided on the US EPA/State of Ohio/Ohio Edison/B&W sponsored pulverized coal full-scale limestone injection demonstration, and on the EPRI/Baltimore Gas 8 Electric, Atlantic Electric/B&W sponsored laboratory-scale cyclone coal limestone injection investigations.

Jan 1, 1986

By Rong Lu, Hao Wu, Bing Dai, Guoyan Zhao, Li Cheng, Weizhang Liang

Affected by the disturbance of blasting activities, deformation instability and rock dynamic disasters are prone to occur in deep hard rock roadways. Thus, it is particularly necessary to understand the failure behavior of rocks and roadways under dynamic loads. In this study, a series of impact loading tests were carried out on sandstone samples with and without a circular cavity by a modified split Hopkinson pressure bar (SHPB) test system. The mechanical properties and energy evolution of the samples were systematically investigated, and the effect of cavity size was analyzed. The results showed that the presence of the cavity in the samples weakens the dynamic compressive strength by more than 10%, and the peak strain and brittleness are also reduced to varying degrees. Under dynamic loading, spalling cracks occur first on the roof and floor of the cavity, and then different numbers of shear cracks are formed on the sample diagonals. The eventual shear failure mode is the result of the connection of the shear cracks and the cavity. As the cavity radius increases, the dissipated energy density and fractal dimension both grow accordingly, leading to smaller and smaller rock fragments. The dynamic failure behavior of the circular cavity can be well explained based on the dynamic stress distribution law. Overall, this study can provide a reference for the study of the mechanism of rock burst in deep roadways.

Feb 18, 2021

By Ali Kazmi, Wern-ping N. Chen

A load rating procedure was performed to evaluate safe load capacity of the Port of Miami Tunnel (POMT), FDOT Tunnel No. 871071 SR 887. The rating procedure performed on a total of eleven stations beneath roadways and with fill depth less than the tunnel exterior diameter (42 ft). Calculations on tunnel sections passing beneath roadways were performed to evaluate the structural response of the sections subject to moving vehicular loads, dead load, and earth pressures. Ratings were performed in accordance with AASHTO and FDOT guidelines. The procedure considered two types of vehicles (HL-93 and FL-120) and two rating levels (Design level and Permit level). As part of HL-93 vehicle, Tandem load was also considered for rating, separately. For HL-93 and HL-93 Tandem, inventory and operating level ratings were performed. The results show rating factors are high. The minimum rating factor is 16.8 using Inventory truck HL-93. For Permit level using FDOT FL-120 truck the minimum rating factor is 6.9. As can be seen, rating factors are higher than comparable analysis for bridges. This paper explains how the procedure can be implemented for tunnels and evaluates the rating results.

Dec 1, 2022

By Cem Şensöğüt, Özer Ören, Yaşar Kasap

The mining sector, which has an important place in terms of raw material and energy supply, is referred as a sector with one of the highest fatal accidents in comparison with other sectors. In this century, where occupational health and safety awareness has increased, it is important to review the past accident statistics and to determine the current deficiencies by using the information in the inventory. In this study, the Malmquist total factor productivity index (MPI) has been utilized to investigate the changes in the work accidents occurring in the Western Lignite Corporation (Turkey), where underground and surface production methods are applied, and to determine the measures to be taken. According to the results obtained, both the decrease in production amount and the increase in the number of accidents caused inefficiencies during the period in concern due to the expected 10-year economic life of the mechanized system operating in the underground production panel that came to an end in 2007 and the flooding took place in early 2017. Compared with the underground operations, it has been determined that production can be carried out at the appropriate scale despite the heavy working conditions encountered due to the changing climatic conditions and the progress of production in the surface operations.

By Walter R. Hibbard

Precipitation in the northeastern United States, Florida, California and in many industrialized areas of the world is now more acidic (lower pH) than can be accounted for by natural causes. At the same time, the acidity of many lakes and streams in the northeastern United States has been measured and found to be similar to that of actual rain. These facts have led to conclusions that the two conditions are related. Coal burning utilities, 700 to 1000 miles upwind, have been accused of being the cause, leading to proposals for strict emission controls on the alleged offenders. The costs of these controls would place an estimated $10 to $15 billion capital burden on utility customers in about 15 states plus $2 to $6 billion annual operating costs. There appears to be no direct well-established scientific evidence that the accused are guilty but that the indictment is based largely on circumstantia1 evidence. This study examines the evidence, describes the situation and proposes what must be done to reduce the acid precipitation in an orderly cost beneficial manner. It is interesting to observe that studies by the different adversaries on the acid precipitation issue come to different conclusions largely because they do not read the same literature, but selectively develop evidence to support their own points of view, This study will try to review the issues impartially and reach a position of scholarly balance.

Jan 1, 1982

By Donald E. Hendrickson

A new prinicple of side dumping front end loading for underground mucking machines has completely changed the concept of underground loading and haulage equipment arrangement both in production and development work loading. Versatility and adaptability of this type of machine permits combinations with a broad range of haulage means not possible with -conventional overhead loaders. Steel "armored" conveyors serving this type of loader are replacing conventional rail mounted car haulage to give a continuous loading operation and effect important economics of reduced manpower, faster loading rates and fewer working areas for a required production. First used in Germany this easy to control and highly efficient means of placing rock from the muck pile on or into haulage means has advanced the art of underground rock loading more in the past three years than any other advancement since the first successful small crawler mounted air powered loader was introduced in 1954. Bucket type loaders with a relative new side dump principle are gaining in popularity for underground loading. They are replacing conventional overhead loaders in present applications and becoming first choice in new ones. Primarily for hard rock development and production loading they are also widely used in production loading of coal and other soft materials. This discussion briefly traces the historical development of hard rock underground loaders to the new side dump type and its present population. In more detail various applications, loading techniques and the advantages of operation, production and economy with the side dumper in hard rock loading will be dealt with.

Jan 1, 1966

By Fred Pena

Cyprus Pima Mining Company is located in the Mineral Hill District of southern Arizona, approximately 22 miles south-southeast of Tucson. Cyprus Pima Mining Company is owned 50.01% by Cyprus Mines Corporation, 24.99% by Utah International Incorporated, and 25% by Union Oil Company of California, with Cyprus having the management responsibility. Cyprus Pima's history has been one of continued expansion from an initial plant of 3,000 TPD in 1957; 6,000 TPD in 1963; 18,000 TPD in 1966; 36,000 TPD in 1967; and 53,500 TPD in 1972. The major reason for Expansion IV was that a large volume of low-grade ore had to be moved to get at a higher grade ore in the course of proper pit development. With mining costs already defrayed, this relatively hard, low-grade material became economically profitable for subsequent milling and concentrating treatment. Similar material previously stockpiled was available for ore treatment. In an effort to meet the continuing search for lower unit costs, the largest milling and concentrating equipment had to be examined. The management of Cyprus Pima Mining Company began investigating autogenous, and semi-autogenous milling in 1964 when two carloads of ore selected from the Cyprus Pima pit were sent to the Koppers--Hardinge Operation at York, Pennsylvania for testing. One car contained approximately 40 tons of hard arkosite and the other contained approximately 40 tons of ore classified as soft Hornfels. The purpose of the testing was to determine the amenability of both ore types to autogenous or semi-autogenous grinding.

Jan 1, 1974

By Ronald C. W. Webber‑Youngman, Philani Larrance Ngwenyama

Entrapments are a huge risk in underground mines. This happens when miners (or any other persons who have entered underground) survive the initial event of an accident, become trapped or lost in unknown and life-threatening locations after evacuation, and remain unaccounted for. At this point, every second counts, and emergency response is highly desired for any chances of saving survivors. The survival chances of the missing persons depend on how quickly they can be located. Rescue teams are often deployed to search for the missing persons underground. However, the rescue teams are forced to search in random and presumed areas of the mine. This is due to the unavailability of information pertaining to the whereabouts of the missing persons. Not only the provision of accurate locations, but various other types of information such as post-accident two-way communication can enhance the survival chances of the missing persons. This information can be provided by a fit-for-purpose missing person locator system. A wide variety of missing person locator systems are already commercially available, some are in testing phases and others in prototype and development phases. This includes tracking, tracing, location detectors and post-accident two-way communication systems. These systems have unique functionalities, capabilities and limitations; making it difficult for mines to select the most effective, applicable and suitable system specific to their mine. In this study, the user requirements for a fit-for-purpose missing person locator system were developed. The purpose of the user requirements was to provide a guideline to facilitate the system selection process. The user requirements can also be used as a tool to measure and evaluate the performance of the selected missing person locator system. The user requirements were also used to predict the success of the selected system under different missing person incident scenarios. The development of the user requirements showed a potential for many other benefits for missing person locator systems.

Nov 2, 2023

By N. Damiano, C. Zhou, B. Whisner, M. Reyes

"The Industrial Internet of Things (IIoT), a concept that combines sensor networks and control systems, has been employed in several industries to improve productivity and safety. U.S. National Institute for Occupational Safety and Health (NIOSH) researchers are investigating IIoT applications to identify the challenges of and potential solutions for transferring IIoT from other industries to the mining industry. Specifically, NIOSH has reviewed existing sensors and communications network systems used in U.S. underground coal mines to determine whether they are capable of supporting IIoT systems. The results show that about 40 percent of the installed post-accident communication systems as of 2014 require minimal or no modification to support IIoT applications. NIOSH researchers also developed an IIoT monitoring and control prototype system using low-cost microcontroller Wi-Fi boards to detect a door opening on a refuge alternative, activate fans located inside the Pittsburgh Experimental Mine and actuate an alarm beacon on the surface. The results of this feasibility study can be used to explore IIoT applications in underground coal mines based on existing communication and tracking infrastructure.IntroductionThe U.S. approach to health and safety in mining has historically been reactive in the sense that health and safety regulations and mandates have traditionally been passed as a result of tragic mining accidents. An example of this is the Mine Improvement and New Emergency Response Act (MINER Act) of 2006, which was passed as a result of several mining accidents where tracking of and communication with underground personnel were severely limited. While this reactive approach has led to the development and implementation of highly impactful safety interventions and safety practices, there exists a technological revolution that can shift the paradigm toward a proactive approach based on preventative methods: Internet of Things (IoT).IoT is the network of physical objects, or “things,” embedded with electronics, sensors and connectivity to enable that network to achieve greater value and service by exchanging data with the manufacturer, operator and/or other connected devices (Atzori, Iera and Morabito, 2010; Gubbi et al. 2013). It should be noted that IoT has been defined from various perspectives, and hence numerous definitions exist in the literature. The apparent ambiguity of the IoT definition might be due to the fact that IoT is syntactically composed of two terms: the Internet and things. The first word pushes toward a network-oriented vision, while the second tends to put the focus on generic objects. The traditional Internet can be viewed as an internet of computers, so things connected to the Internet are computers only. IoT extends the internet by allowing other generic things that are commonly found in daily life, such as refrigerators and cars, to be interconnected through the Internet, thus creating a bridge between the virtual world and the physical world"

Jan 12, 2017

By Mehmet Ali Recai Önal, MAHMUT CAMALAN

Mineral liberation is one of the primary objectives in comminution circuits for the downstream separation of valuable minerals. Breaking minerals through their grain boundaries (grain-boundary breakage) enables mineral liberation in their natural grain size, removing the need for intensive grinding. This study aimed to evaluate if gaseous carbon dioxide, oxygen, or hydrogen can be used as grinding additives to promote the liberation of chromite grains by grain-boundary breakage. For this purpose, chromite ore particles in the −9.53 + 6.35 mm size fraction were pretreated by exposing them to carbon dioxide, oxygen, or hydrogen flow. Then, the untreated and pretreated samples were broken in a drop-weight tester under the same conditions. Finally, the graderecovery plots of chromite grains in the selected progeny size fractions and the overall progeny distributions were measured and compared. Pretreatment with carbon dioxide flow was found beneficial for grain-boundary breakage. It significantly enhanced the liberation of coarse chromite grains along with the overall progeny fineness. EPMAanalysis showed that the adsorption of carbon dioxide seems to reduce aluminum concentration at grain boundaries, which could be the reason for grain-boundary weakening. These results suggest that carbon dioxide can be used as a grinding additive, reducing the carbon footprint of the mining industry.

Oct 29, 2020

By F. Carew

Accurate knowledge of what mass and grade is to hand and where it is stored is key to mine efficiencies and overall profitability. In order to make the right decisions and align production with stockpile capacity, feed and contract demand, a clear and accurate view from production through blending and processing is required. The use of a mine production management solution can provide you with a high degree of confidence in and visibility into validated data as well as auditable and traceable material movements, activities and surveys. A robust calculation engine enables mass and grade changes to propagate to material movements and stockpiles to ensure you are getting the most accurate view at all times. Tracked changes in material balances can be readily incorporated in revised production schedules to close the loop. The availability of accurate, timely information, coupled with predictive trend indicators, is a significant advance in narrowing the gap between claimed and planned production that is common to many mines, regardless of commodity. This paper provides an overview of a Mine Production Management System (MPMS) and explains how the system helps address the challenges listed above.

Jan 1, 2011

By B. A. Wills

With the increasing need to mine lower grade ores, high energy-related costs in comminution are of major concern. Very fine grinding is needed to liberate the very fine mineral particles in these ores. Not only is this expensive but it leads to greater losses in 'slimes'. In the early 1970's, 50% of the tin mined in Bolivia, 30% of the phosphate mined in Florida and 20% of the world's tungsten were lost in this way (Somasundaran, 1979). Gravity concentration techniques become unacceptably inefficient for particle treatment below 25-50µm, and even flotation fails in the ultra-fine range. Two approaches can be adopted to try to overcome this problem. The first involves increasing the efficiency of existing equipment or developing new slimes treatment processes. Gravity devices such as the Bartles-Mozley concentrator have been developed for this purpose and good recovery has been reported from 100µm down to 5µm. Such machines, however, have relatively low throughputs, so that large areas of plant space are generally required. Flotation is rapidly growing in importance for the treatment of ultra-fine minerals traditionally treated by gravity concentration.

Jan 1, 1986

By G. D. Mainwaring, Weng L. W, Lam Y. K.

The first power transmission cable tunnel in Singapore was the 2.6km long undersea tunnel between Pulau Seraya and mainland Singapore, constructed in the1980s. Ten years later, similar concepts were used for the Tuas Cable Tunnel. The tunnel, which includes a 2.2km long immersed tube section, was designed to accommodate 10power circuits of 400kV and 230kV capacity. It is fully equipped with sophisticated control and communication equipment, fire suppressant and life safety systems plus a maintenance vehicle which runs on tracks through the length of the tunnel. The paper discusses the planning, design, and construction of the Tuas tunnel, and the development of these concepts for future tunnels.

Jan 1, 2001

By R. Y. K. Yang, O. Olajide, E. H. Cho

"This study focuses on partial leaching of coal pyrite with sodium sulfite in order to increase its degree of liberation from the coal matrix, which might help to increase the removal of coal pyrite, together with trace elements of arsenic (As), selenium (Se) and mercury (Hg) by froth flotation. The U.S. Bureau of Mines’ two-stage reverse flotation process was applied to further reject coal pyrite in the second stage, where pyrite was floated while coal was depressed. The results show that the leached coal flotation with sodium sulfite produced lower pyritic sulfur content in the clean coal by approximately 25% compared to the flotation of unleached coal. The synergism mechanism between the leaching and the two-stage flotation is delineated. The rejection of trace elements (As, Hg and Se) after the two-stage flotation process with unleached coal followed approximately that of pyritic sulfur (64.6%). However, after the two-stage flotation with leached coal, the rejection of Se was as high as that of pyritic sulfur (77.9%), while the rejections of As and Hg were 20% lower than that of pyritic sulfur, or followed approximately the same rejections obtained through the two-stage flotation with unleached coal.IntroductionSO2 is a reducing reagent, but when it is combined with oxygen in an acidic solution, it will become a strong oxidizing reagent for leaching coal pyrite. Sundaram et al. (2001) found that the reagent could leach coal pyrite to produce ferric iron, which, in turn, catalyzed the oxidation of SO2. Similarly, Cho et al. (2009) found that the reagent could leach pyrite as well as mercury from coal. In the present study, coal was preconditioned by partially leaching coal pyrite in water-coal slurry with sodium sulfite at 48° C. The partial leaching of coal pyrite may enhance its degree of liberation from the coal matrix and give a chance to be rejected more effectively during the flotation.The two-stage U.S. Bureau of Mines’ reverse flotation process (Miller, 1975) was used in this study. The first stage is conventional flotation, in which coal is floated while material with higher ash and pyrite content remains in the cell. Kerosene is used as a promoter to float the coal and MIBC (methyl isobutyl carbinol) is used as a frother. In the second stage, the floated coal from the first stage is depressed using a starch-based reagent, while coal pyrite is floated using potassium amyl xanthate. In this second stage, the liberation of coal pyrite from the coal matrix seems to be an important factor for successful rejection of coal pyrite."

Jan 1, 2015

By K. Terhaar, K. Prisbrey

The objective was to determine operating protocols for a lead and silver column flotation cleaner, being considered for installation at Sunshine Mining & Refining Co.’s Kellogg mill in Northern Idaho. In this column, tetrahedrite and galena were floated, and pyrite and other gangue minerals, including siderite and silica, were depressed. The procedure was to develop a dynamic simulation using a linear transfer function approach. The transfer function related cause and effect variables such as the influence of collector and depressant dosages on recovery and grades. Bench-scale flotation tests followed by pilot column testing provided the data used to develop a linear transfer function. The transfer function was derived using a spreadsheet. This model was applied to simulate how the flotation column could be made to respond to disturbances in feedgrade. The results were that xanthate, zinc sulfate, and sodium cyanide were found to be suitable controls for grade and recovery. Simulations showed the best sequence of manipulations of these reagents, and these sequences were useful for future operator training. The conclusion was that linear transfer functions were able to simulate lead and silver recovery, develop scenarios for operator training, and provide a foundation for future on-line control.

Jan 1, 1999

A bearing isolator is a noncontact, nonwearing, permanent bearing protection device. It has a rotor and a stator, and the two are unitized, so that they do not separate from one another while in use. The rotor turns with a rotating shaft, while the stator is pressed into a bearing housing. The two components interact to keep contamination out of the bearing enclosure and the lubricant in. Bearing isolators do not require lubrication or any particular shaft finish or condition. The best bearing isolators are made of metal, usually bronze. They use a vapor-blocking feature that inhibits the free transfer of vapor contamination when the rotating equipment is cycled on and off.

Jan 1, 2004

By Fred D. Wright, Stefan H. Boshkov

12.1-BASIC AND PARAMETRIC CRITERIA IN THE SELECTION, DESIGN AND DEVELOPMENT OF UNDERGROUND MINING SYSTEMS STEFAN H. BOSHKOV AND FRED D. WRIGHT The criteria governing the selection of an underground mining system relate to several factors the importance of which varies with geographic location, the state of development of the industrial technology, the economic climate in the Nation and, perhaps, in the world-all these as functions of time. Thus, the best choice of a mining method depends upon sets of definable and undefinable values for numerous factors that may be considered fixed at the precise point in time. Subsequent changes in economic and/or technological developments may necessitate modification or complete revision of the existing mining system. A classification of criteria for selecting a mining system must be based on the broadest definitions. Specific cases may present simple solutions or pose very intricate questions, the answers to which are frequently based on judgment rather than explicit logically reasoned and derived results. Specific criteria may be of negligible consequence in some instances and of overriding importance in other cases. It would be foolhardy to attempt to point out, in the limited space available, all possible variations and interplay of factors, as well as to define the setting in which this interplay can take place. The reader is, therefore, referred to the case histories described in the subsequent parts of this section where actual practice will point out the variability of the problems encountered in the selection of a mining method. A popular thesis suggests that the proper approach to selecting the method of mining should be rooted in the inverse solution, whereby the limitations of the various methods in use serve as criteria to eliminate most of these methods from consideration in the specific case. This narrows the ultimate selection to one or perhaps two most appropriate methods. At this stage, a critical comparison analysis will lead to the ultimate choice. Although such a negative approach un¬questionably is valid in discarding obviously inapplicable mining systems from consideration, it falls short in defining the best system, which in practice quite often turns out to be a variation of a textbook standard, or a combination of two or more such standards. Because the deployment of capital and manpower over a long-term commitment closely follows the selection of the mining system, the decision-maker can well afford to spend a great deal of time and effort in evolving the optimum solution for the peculiarities of his specific case. Within the basic engineering tenets of economy and safety to which the design of a mining system must adhere lie numerous factors of constraint which may be grouped, somewhat arbitrarily but for ease of discussion, into several categories. The criteria that enter into the choice of a mining method derive from the following groups of factors: 1. The shape, size and spatial position of the ore deposit.

Jan 1, 1973

By Larissa Koroznikova, Steve Durkin, Patrick Bouwmeester, Michael Tuck

In currently used mining methods, blasting techniques often causes dilution of valuable ore and results in costly processing requirements. In the context of narrow vein mining of thin and highly concentrated orebodies there is a need of a mining method that can reduce dilution in order to remain economically viable. This research project explored the viability of a new mining technology, thermal fragmentation, in narrow vein mining. Thermal fragmentation technology uses a flame jet to produce extreme heat that spalls the surrounding rock to a strategically located drill hole, as an alternative to traditional blasting. This paper creates a net present value (NPV) model of a mining method using thermal fragmentation, as well as for an existing method used for narrow vein mining; comparisons and evaluations were made regarding the feasibility of the new technology. It was found that while overall costs for thermal fragmentation were relatively high, reductions in wages, haulage and processing costs, as well as increased productivity and ore recovery, meant that the new method would improve the financial performance of any operation. These results identify that there is an opportunity to introduce the thermal fragmentation technology to narrow vein mines within Australia, in order to lower costs and increase profit.