Search Documents

By Sun Guangzhong, Liang Jinhuo

Adverse geological condition is a major factor which makes construction difficulty in tunneling. But if it is predicted and tunnel support is made efficiently in time, the above difficulty can be reduced. It is necessary to develop one or several effective and economical geological methods for prediction of tunnel geology while expensive and time-consuming instruments are used. This paper reviews and proposes several geological methods for prediction of fault, seam, contact zone, and groundwater inrush. These methods have been proved to be effective and economical in tunneling practice in China.

Jan 1, 1987

By F. Calizaya

The PT Freeport Indonesia‘s Deep Ore Zone(DOZ) copper deposit is located in the province of Irian-Jaya, Indonesia. Currently, a block cave mine is being developed around this deposit. Production is scheduled to start in year 2000 and to ramp up to25,000 tpd by year 2003. The air quantity requirement for this mine is equal to 780 m3/s. To supply this quantity, the mine will require five centrifugal fans (one 450 and four 750 kW fans). This study summarizes the technical aspects related to the installation and commissioning of one of these fans. The fan was installed on the surface in a parallel arrangement with two others. It has a design capacity of 240 m3/s of air at 2.2 kPa of static pressure. The study presents the installation details from the underground shaft excavation and portal development through fan testing and commissioning. It also presents the results of a monitoring system that was installed to determine the fan duties.

Jan 1, 2000

By Walter Hermülheim, Klaus-Dieter Beck

In German hardcoal mining approximately 1 or 2 cases of spontaneous combustion are recorded per 10 million tonnes of saleable output. In approximately every 20th spontaneous combustion case, CH, is ignited. By the example of a fire caused by spontaneous combustion on Friedrich Heinrich colliery, an overview on the measures taken for firefighting and explosion prevention is given. These measures comprise (in sequential order) - early fire detection by CO-monitoring, - gob-sealing measures against ventilation air leaks, - full-space inertization of the coalface subsequent to a CH,- deflagration, - installation of a target inertization of the caved-in gob under the protection of the full-space inertization, - re-opening of the fire zone and reestablishment of the ventilation-air current, - completion of the salvaging work with continued target inertization of the caved-in gob and further sealing measures (monolithic packing), - sealing of the coalface after salvaging. The measures described allowed gain of control of a safety- critical (because close to the face) gob fire caused by spontaneous combustion, in spite of a CH, deflagration, within few days only, and salvaging of equipment from that coalface and start-up of the follow-up coal-face on schedule. The measures taken as well as the experiences gained allow deduction of general safety criteria for fighiing of gobfires caused by spontaneous combustion, and for controlling the explosion risk. e.g. - warning and alert thresholds for early detection of fires, - criteria for spotting of the zone of fire, - rules for tightening caved-in gobs, - thresholds for the retreat of firefighting crews from the vicinity of the zone of fire, and for starting ineiization, - considerations for positioning of and strength requirements for stoppings with/without inertization, - flow-by-volume adjustment of inertization, - safety rules for work with respiratory apparatus in the inertized zone, - safety rules for the re-opening of zones of fire. The considerations end up in the conclusions that the duration in terms of months of the classic cycles of sealing, waiting, and reopening can nowadays be reduced to a few days only by purposeful combination of full-space inertization and locally confined tar- get inertization of the gob area. The earlier high risks incured by the mine resuce squads en- trusted with sealing of zones of mine fires under explosion hazards can be reduced by the method described, provided the safety regulations are conformed with. In this way, intertizing contributes substantially to reduction of down-time caused by mine fires, to preservation of recoverable parts of the deposit, and to improved safety of the fire-fighting crews.

Jan 1, 1997

By M. E. Kravetz, E. B. Milosavljevic, L. R. Solujic

Gold ores containing high levels of cyanide-leachable copper minerals, such as covellite, chalcocite, bornite, malachite, azurite, and cuprite have traditionally been difficult to treat economically. A novel hydrometallurgical process for efficient treatment of cyanidation effluents obtained by leaching high copper gold ores (or concentrates) based on the use of Cherokee Chemical organo-sulfur reagents (OSR-A, OSR-B and OSR-C) is described. The process may be modified to selectively precipitate silver, or completely recover silver, copper and zinc, as well as regenerate significant amounts of cyanide. For example, data obtained demonstrate that 100 % of silver and zinc, and 98 % of copper were removed from the solution, while 80 % of cyanide was recovered. The treated barren solutions exhibit enhanced gold and silver leaching kinetics compared to the untreated controls.

Jan 1, 2004

By Liming Yuan

To reduce fire hazards from spontaneous combustion of coal in longwall gob areas, a series of computational fluid dynamics (CFD) simulations were conducted by the National Institute for Occupational Safety and Health (NIOSH) to model the spontaneous heating of coal in longwall gob areas. The previous modeling results demonstrate that spontaneous heating of coal usually occurred behind the longwall shields and along the face with a bleeder ventilation system. Assuming a stationary longwall face, the spontaneous heating could turn to a spontaneous fire in several days for the most reactive coal under favorable conditions. When the longwall face advances, the spontaneous heating process will be significantly affected. In this study, the effect of longwall face advance on the spontaneous heating in the gob area is investigated using the CFD model developed in previous studies. One longwall panel with a bleeder ventilation system is simulated. The width of the panel is 300 m (984 ft), while the length of the panel is changed between 1,000 to 2,000 m (3,280 to 6,560 ft). The same permeability and porosity profiles are used for gobs with different lengths. The spontaneous heating first develops in the gob when the longwall face is stationary. Then, the face advances at a certain rate. The face advance is simulated as a series of discrete movements, and the effect of the face advance on the maximum temperature developed during the face stoppage is examined.

Jan 3, 2010

By G. P. Tomaino

Talc is a layered, hydrous magnesium silicate mineral. It has a soft, soapy feel and typically a smooth texture. Talc is also known for its insulation, heat resistance, chemical stability, oil absorption and strong covering quality. Talc, Mg3Si4O10 (OH)2, has a theoretical chemical composition of MgO at 31.7 percent, SiO2 at 63.5 percent, and H2O at 4.8 percent. However, talc’s chemical and mineralogical composition can vary depending on its geological history/parent rock association. These mineral associations and variable levels are usually chlorite and carbonates (magnesite, calcite and dolomite). Two key elemental substitutions that can occur in the talc crystal structure are iron for magnesium and fluorine for hydroxyl. These compositional differences may limit or enhance the talc’s usage in specific market niches. The United States remains self-sufficient in most grades of talc.

Jan 1, 2005

By R. Oler

The mining industry?s traditional preference for protective coatings in corrosive environments, due to cost considerations, has been to apply galvanized and epoxy coatings. As a result of extreme pH levels and the limitations of current products, a new coating has been developed to withstand severe conditions. Harsh chemicals and corrosive groundwater pose added challenges to mines in maintaining long term ground support which demands continuous rehabilitation. This paper highlights the challenges and identifies a solution by applying a new economic coating to DSI?s Omega Bolt? that withstands the most corrosive of conditions. [ ]

Jan 1, 2012

By Z. Yu

Low-rank/oxidized coals respond poorly to oil agglomeration. Emulsification of kerosene in the presence of surfactants dramatically reduces the size of the kerosene droplets. While this dramatically reduces the amount of oil that is required for efficient agglomeration (down to 0.25-0.5%), more importantly, the surfactants entirely change the electrokinetic properties of the oil droplets and thus the interaction between oil droplets and coal particles. Consequently, kerosene cationic emulsions can efficiently agglomerate oxidized coal particles. The agglomerates obtained in such a process can still be recovered by screening. Surfactants can affect fine coal filtration very profoundly when used to emulsify the oil which is utilized to agglomerate coal prior to its filtration. This sequence is much more logical than the use of flocculants - highly hydrophilic polymers - as filtration additives to aid dewatering of flotation concentrates. Although such polymers flocculate coal particles, they also render coal surfaces hydrophilic and make reduction of the cake moisture content difficult.

Jan 1, 2000

By P. Conrad

Experience has shown that, since the passage of the Surface Mining Control and Reclamation Act, over-compaction of spoil during the reclamation process has severely limited tree growth on reclaimed land. Researchers at the University of Kentucky have conducted a ten-year investigation at a surface mine in eastern Kentucky that monitored the changes in selected spoil physical characteristics for various reclamation and compaction alleviation methods. More specifically, research plots were developed for reforestation that employed three different levels of compaction and two different methods of ripping for overly compacted spoil. Each year measurements were made in the field of dry bulk density, using a nuclear density gage, and maximum penetration depth, using a recording cone penetrometer. In addition to good correlation between tree growth and selected spoil characteristics, the data demonstrated a gradual convergence of the measured spoil characteristic data over the study period.

Jan 1, 2008

By Syd S. Peng

Introduction The most commonly used ground control design in coal mining is the determination of pillar size by various pillar strength formulae for mine layout (Bieniawski, 1983; Holland, 1973; Hustrulid, 1976; Obert and Duvall 1967; Wilson and Ashwin, 1972). However, there have been few documented case histories concerning the validity of those strength formulae. Recently there are indications that those strength formulae tend to overdesign considerably. From a safety point of view, there is nothing wrong with overdesign. But an overdesign with large chain pillars reduces the flexibility of machine movement and decreases production. It also reduces coal recovery and, thus, shortens the reserve's life. This is especially true for small operators who own a limited reserve. Those small mines, through past practices or out of necessity, experiment with smaller pillars than those predicted by the strength formulae. Conclusive ev¬idence has been collected that points to the need of a new concept of coal pillar design. Two case studies will be cited to illustrate this point. 3-D US pillar strength formulae Figure 1 shows a sectional layout of a one-unit mine. The seam was about 1.3 m (50 in.) thick with a uniform cover of 64 m (210 ft). A house was located near the center of the section. The homeowner demanded that no surface subsidence and domestic well dewatering should ever be allowed as a result of underground room-and-pillar mining. Physical properties - strength and Young's modulus - of the rock strata including coal were obtained by testing small samples in the laboratory. The uniaxial compressive strength of the coal was 3660 kPa (823 psi). Using various pillar strength formulae, the homeowner recommended that square chain pillars be at least 11 m (35 ft) wide. The coal company, however, desired to pursue optimum coal recovery in the safest and most economical manner. They engaged in three-dimensional finite element analysis of the section taking into account the complete stratigraphic sequence of the overburden. Results indicated that the section can be developed by 5.5 m (18 ft) wide entries at 21 m (70 ft) center-to-center. In retreat, the pillars can be splitted along both centerlines leaving a stump pillar of 5.5 m (18 ft) square at each of the four corners. The 5.5 m (18 ft) square stump pillars still maintained a safety factor of 1.5, although the safety factors calculated by various pillar strength

Jan 11, 1986

By Fred W. Brackebush

In underground stopes that require more than minimal support, backfill is almost universally used. The term cut and fill stopingis used in a broad sense in this section, which describes underground mining methods requiring support. Support in stopes can be classified as local or short-term and general or long-term. Local support for the back of a stope, for example, can be accomplished with rock bolts or timber stulls. General support for the walls of the stope is provided by backfill. Local support provides a safe working place for the stope miners. General support, provided by backfill, preserves the access way to the stope and prevents large scale dilution of ore. Supported methods are a set of cut and fill stoping methods using backfill for general support and various local support methods. his section is subdivided into three chapters: 19.1 Cut and Fill Mining 19.2 Excavation Techniques 19.3 Backfilling Methods

Jan 1, 2008

By C. A. Pryor

The aggregates industry is the largest minerals industry in the United States producing over 2.6 billion metric tons of crushed stone, sand and gravel annually. Approximately 5% of that production is fine material, passing a 75-micron mesh sieve. Of that amount, about 77% is not sold and represents one of the major industry issues. The material accumulates in stockpiles and settling ponds having an operational and economic impact on the site’s bottom line. Many factors cause this material to be produced: from blasting and processing techniques all the way to end use specifications.

Jan 1, 2002

By Poltak Sinaga

PT Kaltim Prima Coal?s 13-km (8-mile) overland conveyor (OLC) was commissioned in 1991. It is a conventional three-roller, 35 degree trough belt type. Cost and performance optimization during initial design resulted in a 5.4-m/sec (17.7-ft/sec) belt speed, 1,000 mm- (40 in.-) belt width to convey 1.35 kt/h (1,490 stph) and 7 Mt/a (7.7 million stpy) of coal. Despite a high initial figure, the belt speed was lifted to 6.5 m/sec (21 ft/sec) in 1996 to accommodate mine throughput in-crease. In 2002, a new low loss ST2100 1,100 mm- (43 in.-) wide belt replaced the ST2250 that was due to be changed-out. An upgrade project was initiated at the end of 2003 to further increase the belt speed to increase the OLC capacity to 30 Mt/a (33 million stpy). Upgrading the OLC by increasing the belt speed was the lowest capital option. Increasing belt width and/or modifying the trough angle to have larger cross sectional area was not an economical option because it would require expensive changes and significant down time of the OLC. To achieve 30 Mt/a (33 million stpy), the belt speed had to be increased to 8.5 m/sec (28 ft/sec). Although such high belt speed looked feasible, there was no information at that time of other OLC operating at such high speed. There was a risk that the conveyor would not operate safely and reliably at higher speeds. This risk was escalated by the fact there was no facility to lower or fine-tune the belt speed once the higher belt speed was implemented.

Jan 1, 2009

By A. Navarra, F. Mucciardi, H. Marambio, R. Parra, F. Oyarzún

"Discrete event simulation (DES) is an appropriate framework for the plant-wide analysis of copper smelters. These smelters apply a common set of chemical reactions: copper-iron sulfides are blasted with oxygen-enriched air, sending the iron into a slag phase and the sulfur into the offgas. Moreover, conventional copper smelters exhibit similar operational dynamics: a smelting furnace operates continually, feeding into an alternating set of converters that produce batches of blister copper. The thermochemical and operational commonalities of copper smelters are integrated within the DES framework. This serves as a common basis to begin evaluating the system dynamics of individual smelters. For complex problems, the simulation framework should be developed in phases, incorporating feedback from different personnel who have complementary perspectives. Sample computations are provided in this paper based on the Hernán Videla Lira smelter, whose production is constrained by meteorological conditions. IntroductionWorld copper production is approximately 18.5 million t/y (Brininstool, 2015), worth $80 billion a year. Out of this total, 75 percent comes from the pyrometallurgical processing of sulfide minerals (Fig. 1), which occurs in copper smelters. The remaining 25 percent is from the hydrometallurgical treatment of oxides and complex ores (Rotuska and Chmielewski, 2008), which uses solvent extraction and electrowinning.The current paper describes the pyrometallurgical processing, recognizing that the underlying thermodynamics and kinetics are well known (Degterov and Pelton, 1999), with the notable exception of minor element transport, such as arsenic (As), antimony (Sb), bismuth (Bi), silver (Ag), gold (Au). The latter is an ongoing area of research, as smelters are faced with increasingly complex ores (Devia, Wilkomirsky and Parra, 2012; Swinbourne and Kho, 2012). This paper focuses on the system dynamics of copper smelter operations, which has received considerably less attention than the chemical thermodynamics and kinetics.Smelter engineers and managers may contribute to the sustainability of their plant by improving their understanding of operational system dynamics. Indeed, we have prompted smelter improvement projects (Navarra, 2016; Navarra et al., 2016; Navarra and Mendoza, 2013) simply by adapting methodologies that are commonly used in other sectors. These previous works incorporate principles from computer-integrated manufacturing (Groover, 2000) and theory of constraints (Dettmer, 2007), featuring the use of discrete event simulation (DES)."

Jan 1, 2017

By Terence P. McNulty

Gold-bearing outcrops were discovered in 1862 by Union soldiers garrisoned at Needles, CA, near the northwest corner of the future State of Arizona. Sporadic mining began several years later, but engineered shaft sinking and mill construction were not adopted at Oatman and the neighboring camp of Goldroad until about 1900. Geological interpretations in 1915 enabled major production during the next decade. In the late-1930s, USSR&M built a new mine and mill in Gold Road and the District flourished until closure by Federal Order L-208 in October 1942. For about a decade, Oatman’s mines were among the largest gold producers in the American West.

Feb 1, 2024

By R. W. Smith, A. M. Raichur, M. Misra

Mycobacterium phlei has very good potential as a hematite flotation collector. The flotation recovery of hematite is dependent upon the solution pH and concentration of the microorganism. The critical pH for maximum recovery of hematite is around three, which corresponds to the point of zero charge of the microorganism. An excellent correlation between the flotation recovery and bacterial adhesion on hematite is observed. The adhesion of Mycobacterium phlei on hematite can be described by the potential energy of interaction calculations using an extended DLVO theory.

Jan 1, 1994

Ground falls (roof and rib) have historically been responsible for about 50% of all fatalities in bituminous underground coal mines. In some recent years, the number of ground fall fatalities has approached zero, indicating that significant progress has been made. On the other hand, last year?s Crandall Canyon twin mine disasters, in which 9 miners perished in violent coal bumps, provided a stark reminder that complacency is premature. One important success has been a great reduction in the number of miners killed inby roof supports. Throughout the 1990?s these accounted for nearly half of all roof fall fatalities, but there have just been two inby incidents in the past 5 years. Progress has also been made in pillar recovery. Safer mining technologies have reduced the number of fatal incidents, but some recent failures have underlined the need for careful management of the retreat mining process. On the other hand, more than 400 miners continue to be injured each year by rock falling from between supports, and 100 more are injured by rib falls. Together, these two categories also account for a large percentage of recent ground fall fatalities. Available technologies such as roof screen, rib bolting, and inside control roof bolters could dramatically reduce injury and fatality rates if they were used more widely. Further advances in these areas will likely be the next big advance in ground control safety. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By L. Sandbak

The Turquoise Ridge Joint Venture (TRJV) is located in northern central Nevada, and is situated within the Basin and Range province, near the northeast end of the Osgood Mountains (see Figure 1). The TRJV mine consists of typical Carlin type- gold mineralization characterized by low strength rock of altered limestones, siltstones, and mudstones. The weak nature of the ground facilitates the underhand cut and fill mining methods. TRJV has been working to optimize ground support and mechanize top cut drift sizes and eliminate operating hazards associated with jackleg drilling. Safety Factor analysis based on bolt strengths has allowed us to pursue larger sized top cut drifts and to evaluate bolt length sizes and spacing. Switching from jackleg sized drifts of 10?W x 10?H to a mechanized 12?H x12?W top cut drift design has the potential to decrease overbreak, provide more uniform drift design sizes and bolt patterns, and increase ore production by at least 38%.

Feb 23, 2014

By Michael E. Stickney

"Soft technology" computers and computer programs-brings to mind a room full of machines, tape drives, disks, plotters, and printers spitting out financial reports. Computers now have a much broader scope of applications because of reductions in equipment size and cost. For example, people now interact directly with computers to control events. Such computers and associated equipment-called interactive control systems-are often small, relatively inexpensive, and can be designed to increase productivity at mining operations. This is accomplished by improving communications between individuals; giving employees the information needed to make decisions in real time, as events are happening; and giving individuals the background needed to perform more effectively. This paper will describe a procedure for determining the return on investment for interactive control systems, and describe four such systems. The analysis process is general in nature and can be applied to any type of mining operation or production process.

Jan 4, 1981

By C. Stoneback

The attapulgite industry saw a year of solid growth after a weaker 2003. Demand was up between 5 percent and 6 percent driven by almost all of the key markets. Construction continued to show record new housing demand, assisted by continued low interest rates. That drove strong growth in construction related markets like coatings, tape joint compounds and other construction materials applications. The agricultural markets rebounded modestly to increase sales for suspension fertilizers, animal feeds and pesticide carriers. Oil drilling also showed strong growth due to high oil and gas prices. Sales to molecular sieve applications grew due to petrochemical and construction demand. The export markets were assisted by further depreciation of the dollar. The only weak area was in nonagricultural granular sorbents, where other sorbent materials continued to dominate.

Jan 1, 2005