Search Documents

By D. A. Newman

A longwall chain pillar is comprised of two distinct zones, a solid elastic core enclosed by an exterior of failed or yielded coal. For the purpose of pillar design, the ability to delineate the extent of pillar yielding and correlate the yielding with the applied pillar load is of fundamental importance. A study was initiated on a longwall section of a West Virginia mine to: (1) delineate the location of the elastic core-yield zone boundary, (2) examine the stress distribution within the pillar, and (3) quantify pillar stability as the longwall face retreated toward an instrumented pillar. A US Bureau of Mines sonic velocity probe was used in conjunction with vibrating wire stress meters to define the elastic core-yield zone boundary and the migration of vertical stress toward the pillar core. The extent of the yield zone as determined by field results is compared with the extent of the failed zone as predicted using a series of equations developed by Wilson.

Jan 1, 1988

By K. N. Han, Q. Xu

The adsorption behavior of gold in ammoniacal solutions on activated carbon was studied. The gold adsorption capacity of the activated carbon and the recovery efficiency were examined. The parameters affecting the adsorption of gold on the activated carbon included temperature, agitation speed, the concentration of cation and anion and the concentration of ammonia. It was found that the maximum gold adsorption was about 10 kg/t of carbon. The recovery of gold by the adsorption, from ammoniacal solutions was found to be dependent upon the initial gold concentration. Under experimental conditions, a gold recovery of 98% was obtained after 120 hrs of adsorption. It was also found that the initial adsorption rate was relatively fast, when compared to the entire adsorption period. The apparent activation energy for the adsorption was determined to be 15.8 kJ/mol. It was believed that the kinetics of gold adsorption on the activated carbon was controlled by pore diffusion.

Jan 1, 1997

Information Technology has addressed those problems unique to senior management in the mineral industry. In general, these problems are those concerned with decision-making. Peter Drucker in his discussion of making effective decisions identifies five phases: (1) define the problem, (2) analyze the problem, (3) develop alternate solutions, (4) decide the best solution, and (5) convert the decision into effective action. The scope of the chapter by Guernsey addresses the first three phases which provide input to the decision-maker. The decisions to be made relate, in most instances, to the economics related to a mineral property or process. Computer models have been designed to generate these economic and financial evaluations. No one model is appropriate to the solution of all management's problems. In this chapter several applications are identified and summarized; a model for the economic evaluation of a mineral property is described in greater detail. The implementation of such models is dependent on the unique needs of management.

Jan 1, 1979

By H. Sis, S. Chander

The beneficial effect of a series nonylphenol polyethylene glycol ether surfactants were tested in the flotation of phosphate ores in which the mixture of sodium oleate and dodecane was used as collector. The performance of nonionic surfactants was first tested in the microflotation of pure apatite mineral. Microflotation experiments showed that the recovery of apatite depends on the number of ethoxylation of the nonylphenol surfactants and decreased with higher ethoxylation. The nonionic surfactant with the smallest ethoxylation group used in this research (NP-4) was then tested in batch flotation of phosphate ores. The flotation of three different size phosphate ores was carried out in the absence and presence of NP-4 surfactant. The beneficial effect of nonionic surfactant was obtained for fine size (-35+150 mesh) and very fine size (-150+400 mesh) phosphate ores at different collector dosages studied. But, in the flotation of coarse size (-16+ 35 mesh) phosphate ore the beneficial effect of nonionic surfactant was obtained only at high collector dosages.

Jan 1, 2002

By Thomas Van Riper

Newmont Mining Corporation started as one man's investment vehicle. William Boyce Thompson, Newmont's founder, was already a millionaire many times when he incorporated his existing Newmont company in Delaware in 1921. The initial stake in the company was $8 million in capital contributed by Thompson and several close associates. In its infancy the company was truly a holding company. It did not operate or manage any properties. This situation changed drastically over time. By 1939 Newmont was actively mining 12 gold mines in North America. The following year, the first copper mine that Newmont ever managed directly, came into full production in South Africa. The period after World War I1 was a glorious one for Newmont. Plato Malozemoff took the helm of the company, and expanded its operations over the next 30 years into copper in Arizona, oil and gas in the U.S. and the North Sea, into domestic coal and thankfully, into significant gold operations.

Jan 1, 1989

By Fred N. Kissell, Robert J. Timko

Safe escape from coal mine fires continues to be a concern of the mining industry. The most life-threatening fires occur outby the working sections. Because stoppings always leak some air, an outby fire may in time cause intake escapeways to become contaminated with smoke and toxic gases. Smoke and gas infiltration into intake escapeways can be minimized by raising their air pressure over that of adjacent airways. This can be done by checking off the intake escapeway near the working face. The Bureau of Mines has investigated the use of a parachute stopping as a quick-erect check curtain during mine fires, and the concept has been tested in several mines. In every instance, when a parachute stopping was erected on the section, the intake pressure went up substantially. The pressure-raising effect of the parachute persisted for up to 1200 m (4000 ft) outby. Results indicate that checking off the intake escapeway may serve as a viable way to improve safety during mine fires.

Jan 1, 1991

By J. Partyka, Trevor R. J. Kelly

This paper presents the results on noise testing of a fan only, as well as the results of a steel silencer and of flexible silencers that were connected directly to a fan. On-site facilities and free-field method set by the British Standards Institution were used to measure and then compare the fan only and different practical silencer configuration setups. In order to determine the fan-silencer combination that would give the maximum noise attenuation, total noise intensity, noise contributed to by the fan motor only, as well as aerodynamical noise created through air interacting with the fan parts were considered to obtain decibel readings for the octave bands. Subsequently, the optimal configuration found was the setup with flexible silencers on the fan inlet and the fan outlet. If only one silencer is used, it should be installed on the fan inlet. The aerodynamic noise affects the low frequencies. The flow noise is then overtaken at 1 kHz by the mechanical noise.

Jan 1, 1995

By John Jonkman

Two major changes occured during the last 5 years in the applications of computers. First, the cost of computer equipment decreased drastically in an era of high inflation. Second, technological breakthroughs in hardware and software have been applied successfully so that the average person can successfully utilize the computer without having to be a computer expert himself. The mining industry has recognized that computing technology has evolved to a point where it can be applied successfully to assist in improving productivity. Since equipment downtime is one of the major reasons for lost production, the Kennecott Minerals Company has developed a comprehensive maintenance information system which now assists the maintenance department in minimizing equipment downtimes. This paper discusses the primary features and functions of this system, the state-of-the-art technology that has been applied, and the benefits that resulted from using this system. Programs to support mobile equipment maintenance scheduling, which currently are under development, are reviewed and a summary of future applications is given.

Jan 1, 1982

By H. Zhu, A. G. Journel

Qualitative and interpretive information as obtained from geological and/or geophysical studies, in addition to precise measurement, is incorporated into the estimation process through an indicator variable. The indicator conditioned estimator is formulated as a cokriging, and its expression is data value dependent as opposed to that of the traditional kriging estimators. The solution of the dual cokriging system provides simultaneously an estimate of the unknown and an estimate of the conditional probability that the unknown belongs to a specific population or class. Being an unbiased and minimum-error-variance estimator by construction, the indicator conditioned estimator is better in the least square sense than the ordinary kriging estimator because it uses additional information carried by the indicator data. A case study using a large reference database is presented; the indicator conditioned estimates have a smaller conditional bias and a smaller error variance than the ordinary kriging estimates. The results also showed that the indicator conditioned estimator is more efficient for selection in mining.

Jan 1, 1990

By Alden B. Carpenter

The Dead Sea is the only relatively large body of surface water having bromide concentrations comparable to those in the brines of the Smackover Formation in Arkansas. The Dead Sea, like the Smackover brines, contains a great deal of calcium and is very low in sulfate and iodide. The relationships between potassium, divalent cations, and chloride indicate that over 20 percent of the bromide in the Dead Sea is derived from some source other than by the evaporation of sea water. A similar type of study of the Smackover brines in Arkansas indicates that approximately 60 percent of the bromide has been derived from some source other than sea water. Both the Dead Sea and Smackover brines are very low in iodide suggesting that the excess bromide has not been derived from organic matter. The origin of the excess bromide is probably the same for both of these brines, but the source of this bromide remains unknown.

Jan 1, 1978

By Robert A. Haney

Utilizing the recently developed laser velocimeter and a Pitot-static tube, the United States National Bureau of Standards (NBS), has calibrated various types of anemometers that are commonly used in the mining industry. This paper presents a summary of the performance characteristics including accuracy, precision, starting and stopping speeds of each instrument tested. The specific instruments that were calibrated by NBS have become Mine Safety and Health Administration (MSHA) primary reference instruments. These primary reference instruments are used in turn to calibrate secondary reference instruments for each Coal Mine Safety and Health District. Each District calibrates anemometers that are used by District engineers and inspectors. Calibration is accomplished through a substitution procedure in which the reading on the anemometer is compared to the true velocity determined by the reference instrument. Calibration is performed over the entire range of the instrument using an open jet wind tunnel to produce the various approximate velocities. Some specific details of the calibration procedure are presented in this paper.

Jan 1, 1980

By J. G. Henning, R. Edrissi

This paper describes a practical methodology, based on numerical modeling, for the prediction of progressive failure of underground-mine stopes having cable-bolt support. A case study of the 40-761 scope at the Kidd Creek mine, Timmins, Ontario, Canada is presented. Scope 40-761 was mined by blast hole open sloping in 1986 and was a lead scope within a mining block located between levels 36-1 and 38-2. Initially designed to peak at level 38-2, the scope back caved upwards =40 m towards level 36-1. After caving began, cable bolts were installed above the stope from level 36-1. The stope eventually stopped caving when the falling rock mass encountered a sufficiently high cable density. This paper provides details of the geomechanical data and modeling results of the case study. Numerical modeling of cable bolts around the mine stoke was carried out using a finite-element modeling software. The software, known as e-z tools, was developed by the first author.

Jan 1, 1996

By R. K. Mehta, K. N. Han, P. B. Queneau, V. Dieudonne

A study based on a statistically designed sets of experiments (central composite design) was conducted to determine the optimum conditions for leaching a subbituminous coal (7.0 % ash) from the middle Wyodak seam in mild sulfuric acid solutions. The statistical analysis was conducted with the ash content and ash removal as the dependent variables and with the coal loading, acid concentration, ferric ion concentration, and temperature as the independent variables. Treatment of the experimental data via a simple genetic algorithm (GA) revealed that acid concentration and temperature are the two most critical variables. Unlike the case with bituminous coal, the ferric ions addition shows no beneficial effect. The optimum "macro response" predicted by GA was verified experimentally; the ash content was reduced to 2.7%, which is close to the value predicted by GA. The ash content was further reduced to 1.7% in a two-stage leaching process devised by incorporating the optimization results with that of leaching kinetic studies.

Jan 1, 1993

By Numan Elmas

Barite deposits located in Dinek and surrounding region have important economic features with their large reserve capacity for Turkey. The objective of this study is to elucidate geological and depositional characteristics in terms of. site investigation and chemical analysis. In order to do this, geological area of about 300 km2 was examined and detailed geological map was constructed. It was observed that Barite mineralization in these deposits was occurred in carbonate and pelitic rocks of Lower Cambrian-Lower Ordovician. Deposits were exposed to advanced diagenesis regional metamorphism and tectonics that rotated and deformed the barites; therefore, barites shows secondary veins, brecciate and fracturing structure. Even though, a few light isotope values of barites may suggest hydrothermal and exhalative sedimentary characteristics or possible mixing with magmatic fluids, generally heavy isotope values indicate that the sulfate ions were supplied from coeval seawater and, many of sedimentary features and petrological, geochemical characters support dominantly sedimentary origin.

Jan 1, 2005

By Y. C. Kim, I. S. Roditis, P. K. Medhi

The strongly skewed grade distributions and the need to estimate the local recoverable reserves in a selective mining environment are the two problems that ordinary kriging (OK) cannot easily handle. With the recent introduction of the non- parametric, distribution-free technique of indicator kriging (IK), the above problems can be solved. This paper describes the result of performance evaluation of IK in an open-pit gold-silver deposit. For performance evaluation, the predictions of local recoverable reserves using IK were compared with the actual reserves based on blasthole information. The IK estimator, although a bit optimistic (or overestimating), performed very well in predicting the total recoverable ounces of gold from each panel on a test bench. The OK estimator was also used to try to predict local recoverable reserves, by treating each panel as either waste or ore, depending on the panel's average grade. Under this criterion, OK was found to be quite biased and pessimistic (or underestimating).

Jan 1, 1988

By Gilles A. Tremblay

Acidic drainage has been long recognized to be the largest environmental liability facing the Canadian mining industry and to a lesser extent the public through abandoned mines. The Mine Environment Neutral Drainage (MEND) Program was the first initiative formed in 1989 to develop scientifically-based technologies to combat acidic drainage. This 9-year volunteer program reduced the liability by several hundreds of million dollars and established Canada as the recognized leader in research and development on acidic drainage for metal mines. MEND 2000 is a three-year program that started in 1998. The key to MEND 2000 is technology transfer- providing state-of-the-art information and technology developments to users. MEND-developed technologies are being verified by long-term monitoring of large-scale field tests. Maintaining linkages with a number of foreign government and industry-driven programs is also important to the successful completion of the program. Through these efforts a further reduction of the environmental liability associated with acidic drainage will be realized.

Jan 1, 2000

By Mary B. Ansari

The literature of mine ventilation is very diverse in nature, widely interdisciplinary, and extremely international in scope. Important references are found in indexes, abstracts, government documents, technical reports, journals, conference and symposia proceedings, and monographs. In this decade computer searches of the literature have greatly aided researchers in finding needed items. There is, however, no convenient summary of recent English language literature in coal and non-coal mine ventilation. This paper attempts to fill that gap in the literature. Because of the worldwide provenance of the subject and the attendant publication deluge, this paper covers only current English language publications on ventilation. The writers have examined the field's English language abstracts, indexes, bibliographies, periodicals, technical reports, books, and symposia and conference, proceedings. The survey also considers the field's most important bibliographic data bases. It should be noted that addresses for many of the literature sources listed in the paper are given in the section on literature and data base information sources.

Jan 1, 1980

By J. A. Finch, J. Yiantatos, A. R. Laplante

This paper re-examines the mixing conditions in the collection zone of flotation columns. These have in the past been characterized with a single uniaxial dispersion coefficient, E. The relationship between E and column diameter, Dc, is examined based on residence time distributions (RTDs) in columns of Dc ranging from 5.lcm to 184cm. Results agree with published correlations in chemical engineering, i.e. E a Dc '" , Data explain why pilot columns display significant upgrading between the feed level and the interface, whereas plant columns do not. It also suggests that, for plant columns, the full collection zone (up to the interface) can be considered when calculating the residence time. A mathematical model considering two regions of different mixing was compared to the single E model. Both models adequately fitted measured age distributions inside the column and overall RTDs. Measured and simulated mixing characteristics are compared to those of flotation banks, using a tanks-in-series approach; banks of comparable mixing to columns are identified.

Jan 1, 1988

By T. Carageorgos

The removal of arsenic from process streams as ferric arsenate compounds is being practised by mining industries. Therefore, the solubility and stability of these solids is of considerable importance to the mining plants that have to keep the environment free from pollutants. There is some information on the solubility of the ferric arsenate compounds, mainly on scorodite, obtained from synthetic solution. However, there is not so much work on ferric arsenate compounds formed at high temperatures (175 - 230°C) during the leaching process. In the present work, the solubility of the ferric arsenate compounds formed during acidic pressure oxidation of arsenopyrite is presented. The results of the solubility tests showed that the ferric arsenate compounds formed at high temperatures (200 - 230°C) and high pressures (1034 - 1551 kPa 0,) released arsenic into solution in amounts less than 1.2 ppm and iron in amounts no higher than 1.0 ppm. So, they seem to be potential compounds for arsenic and iron disposal.

Jan 1, 1998

By R. J. Pugh

The surface chemical sites on several fillers (quartz, feldspar, calcite and granite) were studied by the adsorption of well defined acid and basic probe molecules (benzoic acid, benzyl alcohol, ethyl benzoate, pyridine and benzyl amine) from cyclohexane. The results provided a wide variation of adsorption data, emphasizing the extensive range of site heterogeneity on the filler surfaces. In addition, it was shown that the acidic probes were strongly adsorbed on all of the minerals, thus indicating that the basic surface sites dominate the acidic ones. Also, through FTIR studies with vapor-phase probes adsorbed on orthoclase, it was possible to identify the nature of specific sites and the type of bonding occurring between the filler surface and the probe molecule. These types of surface analytical techniques could give useful information for predicting the adsorption functional groups on dispersants, dyes, thickeners, etc. and could lead to enhanced interfacial bonding between the filler and the matrix.

Jan 1, 1993