Search Documents

By M. Robb, S. J. Bate, M. Boisvert

The never-ending quest for gold-bearing ore deposits is a primary industry in Canada, employing people of widely differing expertise. The exploration models for gold deposits are generally geologically complex and the targets have relatively small cross-sectional areas. These problems are compounded in Canada by the minimal outcrop exposure in most mineral provinces and the high percentage of water-covered areas. Naturally the chances of successfully delineating an economic gold deposit are very much greater if all parties involved can act as a team of explorationists constantly confemng amongst themselves particularly as the applicable disciplines generally overlap and complement each other. Three case histories (see Figure 1) are presented to illustrate this philosophy with emphasis placed on the role of the geophysicist in translating the exploration model as defined by the geologist into physically measurable parameters and identifying target areas with similar characteristics. The Conwest-Miminiska property in Ontario is a grassroots exploration play. Additional ore reserves needed to be delineated on the Salmita property in the Northwest Territories. At Laura Lake, near Chapais, Quebec geophysical methods were employed to trace thin high-grade mineral intersections under deep overburden and severe cultural interference.

Jan 1, 1989

By R. C. Babcock

Exploration for mineral deposits in the western United States is increasing annually, and the data generated by this effort are increasingly complex, diverse, and abundant. It is obvious that to make full use of this data base, which is both private and public, the technology of the computer must be involved. To lay out the framework for discussion of the particular uses of computers in all steps of exploration, this chapter will discuss the various approaches to the reconnaissance program which might be considered, the types of data to be acquired, the interpretation of these data, and the generation of recommendations based on this interpretation. Where possible, some of those areas where computer technology is now used will be pointed out. The discussion will cover the extent to which the computer is now utilized in those areas or where it should be brought into the program to aid in these activities. However, this chapter will not present an exhaustive evaluation of this technology, but will stress the exploration job and its requirements, so that subsequent discussion of the technology itself can be placed in perspective.

Jan 1, 1979

By Murali M. Gadde

Perimeter mining is a special form of very productive partial extraction method practiced at some mines in the United States. In the Illinois Basin mines where all major coal seams have weak underclay in the immediate floor, experience shows that any long-term ground control issues will arise due to floor failures rather than instability of the coal pillar itself. While there is a significant amount of work done on floor stability associated with regular pillars, no work has been done so far on the stability of perimeter pillars. This paper reports the results of a comprehensive study that was conducted for the first time on floor stability during perimeter mining in the Illinois Basin mines. A special plate template, which mimicked a common perimeter pillar configuration was created to conduct in-situ bearing capacity tests at five mines in three states of the Basin. Additionally, because of the complex shape of pillars created in perimeter mining that defies any closed-form solution, floor bearing capacity was studied using three-dimensional nonlinear numerical modeling. Based on these in-situ and numerical studies, some guidelines are provided for perimeter pillar stability analysis.

Jan 1, 2009

By B. K. McMahon

Block caving is an efficient mass-production method for the underground mining of large orebodies. However, the block-caving method requires a substantial investment in developmental works, based on the assumption that the rock will cave. Efficient block caving is prevented if the rock forms stable arches or breaks into fragments that are too large to pass easily through the finger raises. Under these conditions, the cost of the additional labor, drilling, and blasting required to assist caving may be sufficient to make marginal orebodies uneconomic or alternative mining methods more attractive. Reliable methods for the prediction of the block-caving behavior of an orebody are clearly needed at the initial planning stage. These methods should be capable of considering both geological and engineering aspects of a block cave, as experience has shown that the manner in which a block cave is initiated and developed may be almost as important as the geological conditions such as the nature of the rock material, degree of alteration, characteristics of the joints and faults, etc. The initial state of stress in the rock mass should also be considered.

Jan 1, 1969

By Joel K. Waterland

GENERAL DESCRIPTION Open cut-and-fill stoping for many years was prob¬ably the most widely used mining method in under¬ground metal mines. Then for a time this method was largely supplanted by the blasthole stope. It again be¬came popular as many mines reached depths or grades where methods requiring large open voids to remain open for extended periods of time became unsuccessful, often as a result of excessive dilution. The open cut-and-fill method is very flexible and is readily adaptable to almost any ore body. The standard application requires that a slice of ore usually 2.4 to 3 m (8 to 10 ft) thick be removed from the back of the stope, and as the ore is taken down, the back is dressed and rockbolted. After the back is secured, the broken rock is removed through rock passes to the level below. When the rock has been removed, the rock passes are extended upward the height of the ore removed, the stope is backfilled, and another cycle is mined. This method is best employed in plunging ore bod¬ies with considerable vertical extent, ore areas that re¬quire selective mining, ore areas where weak wall con¬ditions exist, and ore bodies that have an ore value that will carry this relatively expensive mining method. Blast¬hole stoping, shrinkage stoping, and other mining meth¬ods that do not employ rock passes in a stope are not efficient in plunging or flatly dipping ore bodies because the footwall makes ore removal quite difficult. Since mining is accomplished by taking down slices of the back, only small areas of the wall rock are exposed at any one time, and these only for short periods. Due to limited back height, areas of uneconomic rock may be left in place, or they may be mined and the material gobbed in the stope. Because the miners in the stope must work under freshly blasted areas, the amount of ground control is usually great. The volume of rock that is broken during one section of mining is relatively small and the amount of nonproductive work required is high. This results in limited productivity for the scope and, be¬cause of the nonproductive work that must be done on a regular basis, the production from the stope may be quite cyclical. SUITABLE ORE BODIES The open cut-and-fill method may be adapted to al¬most any type of ore body with a relatively high vertical extent. The ore body must be accessible at both top and bottom as well as at regular intervals throughout its vertical extent. Although adaptable to most ore bodies, the method is probably best employed where the ore has poor con¬tinuity and where most types of bulk mining would pro¬duce excessive dilution. In areas of poor ore continuity, the capability of continuous and extensive sampling dur¬ing the mining of each cycle makes this method very desirable. This capability also minimizes the amount of evaluation sampling that must be done before mining is started. Because of the extractive system used, the size and shape of the stope may be as readily changed as the sampling mandates. Probably the only ore characteristic demanded is that the ore has strength enough to be sup¬ported through the use of rockbolts or cable bolts dur¬ing the mining and backfilling cycles. Good planning, systematic sampling, and careful supervision will pro¬duce a product with less dilution than any other open stoping method. PLANNING Evaluation Planning Once it has been decided that the open cut-and-fill method would be the most efficient for mining a par¬ticular ore body, the next considerations would probably be the availability of an economical backfill material and the selection of an efficient transport system for this material. Although hydraulically transported mill tail¬ings are the most widely used product, this is not always practical due to mill location or the quality of the tailings. In such cases, backfilling may be used. The type of backfill and the type of equipment used will determine if a floor or capping on the backfill is required to minimize dilution during ore removal. The early selection of rock removal equipment is im¬portant since equipment usually determines the amount of development work required to bring a stope into pro¬duction and the size of the openings needed. The size and continuity of the ore body will usually determine the type of loading equipment. The use of slushers or load¬haul-dump (LHD) equipment captive in the stopes will minimize the amount of development. If the ore con¬tinuity is such that a ramp system for extraction can be used, the cost of development will be increased but the flexibility of continuous mining will minimize the cycli¬cal nature of the production. The height of the mining section usually is deter¬mined by the strength of the wall rock and the amount of back bolting required. Once this has been decided, the appropriate drilling equipment can be chosen. The number and sizes of the rock passes employed depends upon the type and size of the extractive equipment and the type of backfill that is to be used. Since the miners must enter and leave the stope each shift, the level inter¬val is usually maintained at approximately 45 m (150 ft). Access from the level above into the stope must be main¬tained at all times. The employees perform all the work in the stope and adequate ventilation must be provided. Stope Planning Due to the flexibility of the method and the vari¬ability of the ore zones, layout is usually done on a stope basis. In areas where continuity is a problem, the size of the stope is usually determined by the boundary of the ore (with all of the ore within that boundary being removed). In areas of good continuity where ramps are to be used, the length of the stope may be determined by the length of time each of the cycles (preparation, back¬fill, mining, and ore extraction) requires. The ramp work is then laid out so that access to the various parts

Jan 1, 1982

By R. V. Huff

An in-situ leaching technology was developed for copper oxide minerals at the Van Dyke deposit at Miami, Arizona. This paper discusses the process developed and the activities that occurred. Specifically, the activities of well installation, deposit data acquisition, leach testing and equipment development are reviewed. Installation and operation of the test facility are described.

Jan 1, 1988

By J. D. Christensen

In August 1987, we marked the tenth anniversary of the Surface Mining Control and Reclamation Act. Anniversaries are supposed to be times of celebration, and I truly believe that we have something to celebrate on this anniversary. For, after ten years, there has been much progress in the implementation of the surface mining law.

Jan 1, 1988

By K. Fuenkajorn, S. Serata

Discussion by S. Serata and K. Fuenkajorn Background Results of the above study in the August 1991 issue of Mining Engineering offer valuable lessons in the solution of cutter-roof problems. The original study plan was initiated by the discussion authors to solve the problems using the "stress control method" of mining (Serata 1976, 1982; Serata, Carr and Martin, 1984; Serata and Gardner, 1986; Serata, Gardner and Preston, 1986; Serata, Gardnerand Shrinivasan, 1986; Serata and Kikuchi, 1986; Serata, Preston and Galagoda, 1987) However, the plan and the planner were changed to the arrangement reported in the paper. The change was considered reasonable at the time due to the mine engineers' uncertainties about the stress control method. Consequently, the basic principle of the study was shifted from the original stress control method to the method described in the paper, which will be called the "yield pillar method" for the purposes of this discussion. The paper convinces the reader that the yield pillar method fails to solve the cutter-roof problems. This doesn't mean that the stress control method also fails. Actually the contrary is true, as discussed below. Limitation of the yield pillar method The paper illustrates clearly how poorly the yield pillar method performs in solving the problem. The reason for this failure is the lack of the protective stress envelope needed to stabilize the cutter roof. Unfortunately, the protective envelope cannot be formed properly without utilizing the stress control method of mining. Changing the pillar size does not make much difference in the roof stability. Stress measurement The key issue is how to form the global stress envelope to make the gate entries safe for production. Therefore, measuring the stress condition of the ground around the mine opening is critically important to solving the cutter-roof problem, regardless of the method applied. With regard to the stress measurement, there is a serious question as to the reported stress state of [6 i = -51.7 MPa (-7499 psi), G2 = -44.5 MPa (-6458 psi) and 63 = -30.8 MPa (-4465 psi)]. It is mechanically impossible to have such a stress state at any location in the mine ground since the known initial vertical stress [o,,] is less than or equal to 800 psi. There may be a large stress state in the [61] direction, but that is possible only at the expense of the [63] value. Having the above stress tensors in the mine is simply impossible. The questionable, reported stress values could be attributed to the application of the overcoring method, which tends to produce erroneously large stress values in the extremely nonelastic mine ground. Stress control method The paper should be considered as a major contribution demonstrating the limitation of the yield pillar method. At the same time, the paper does not disprove the stress control method. However, in comparing the paper with stress control studies conducted in other similar failing grounds, the stress control method appears to be able to solve the problem more effectively. Therefore it is advisable that the mine not give up its efforts to solve the problem. [•] References Serata, S., 1976, "Stress control technique - An alternative to roof bolting?," Mining Engineering, May. Serata, S., 1982, "Stress control methods: Quantitative approach to stabilizing mine openings in weak ground," Proceedings, 1st International Conference on Stability in Underground Mining, Vancouver, BC, Aug. 16-18. Serata, S., Carr, F., and Martin, E., 1984, "Stress control method applied to stabilization of underground coal mine openings," Proceedings, 25th US Symposium on Rock Mechanics, Northwestern University, June, pp. 583-590. Serata, S., and Gardner, B.H., 1986, "Benefits of the stress control method," invited paper, American Mining Congress Coal Convention, Pittsburgh, PA, May 7. Serata, S., Gardner, B.H., and Shrinivasan, K., 1986, "Integrated instrumentation method of stress state, material property and deformation measurement for stress control method of mining," invited paper, 5th Conference on Ground Control in Mining, West Virginia University, Morgantown, WV, June 11-13. Serata, S., and Kikuchi, S., 1986, "A diametral deformation method for in situ stress and rock property measurement," International Journal of Mining and Geological Engineering, Vol. 4, pp. 15-38. Serata, S., Preston, M., and Galagoda, H.M., 1987, "Integration of finite element analysis and field instrumentation for application of the stress control method in underground coal mining," Proceedings, 28th US Symposium on Rock Mechanics, Tucson, AZ, pp. 265-272.

Jan 1, 1993

By M. Kalin, H. D. Sharma

INTRODUCTION The inactive uranium mill tailings investigated in this study are located in two mining districts, Elliot Lake and Bancroft, Ontario, Canada. The sites exhibit a mixture of surface features consisting of dry areas, with or without vegetation and areas covered with water. On the edges of the water bodies, indigenous vegetation has invaded the tailings beaches [ Typha] spp. (Tourn.) L. a dominant plant on these tailings beaches, has been studied for the uptake of radium-226 and lead-210 (Kalin and Sharma, 1981b) from the tailings. It was found that most of the radium-226 remains in the roots of the plants, and that the solubility of radium-226 in control soil differs from that in tailings. The uptake of radium226 by vegetation and other biota is related to the solubility of the element in water. Factors controlling the solubility of radium-226 in uranium mill tailings are of interest in assessing the environments effects of these wastes. Rusanova (1962) found that the soluble or extractable amount of radium from the soil is inversely related to the total concentration of calcium and magnesium in the soil. Experimental work has clarified some aspects of the leachability of radium from uranium mill tailings (Levins, et al., 1978; Wiles, 1978, and others). Halvik, et al., (1967) studied the effects of pH and chemical composition of surface water on the liberation of radium from uranium mill tailings and uranium ore. He found that an increase in pH, up to a value of pH 9, decreases the amount of radium released from the tailings and the ore. A positive effect of calcium chloride was noted on the leachability of radium. Benes (1981) reviewed the physicochemical forms of radium and its migration in water. Based on experimental work, he identifies primary factors which determine leaching of radium from uranium mill tailings. The ratio of the volume of the leaching solution to the weight of the leached sample; the composition of the leached solids and the leaching solution, and finally the pH of the leaching mixture are of importance. He emphasized that a scarcity of field data exists, which would relate experimental work to the actual situation in the tailings ponds. Inactive tailings ponds in Ontario are 16 to 23 years old, and processes which are of importance in evaluating the long term effects of uranium mill tailings in the environment can be studied. The objective of this work was to investigate the leachability of radium-226 from the tailings under field conditions. MATERIALS AND METHODS Sample Collection A description of inactive tailings sites in Ontario, where the tailings and the water for this study were collected, can be found in a report by Kalin (1981). [Typha] spp. specimens were excavated from 16 different locations along with the tailings attached to the roots of the plants. A tailings sample from the surface area, around the plant, was secured before the excavation. Tailings samples were also collected from dry areas free of vegetation in the vicinity of the wetland stand. Surface samples (depth 0-5 cm) and samples at a depth of 20-25 cm were secured. Water was collected from the shallow tailings beaches around the vegetation stands. Sample Preparation The roots of the plants were washed free of tailings with distilled water. The resulting thick slurry of tailings was allowed to settle in the wash basin for five minutes and the supernatant water was decanted. The remaining saturated tailings were brought to 400 ml volume with distilled water in a beaker. The slurry was mixed with a magnetic stirrer for two 24-hour periods. After the first 24-hours, the slurry was allowed to settle for 20 minutes and the supernatant water was removed. The remaining sediments were suspended again in distilled water (400 ml total mixture) and leached for a second 24hour period. The tailings slurries from the different locations had a solid to liquid ratio, which ranged from 0.5 to 1.4 grams of dry tailings material per millilitre. The variations in the ratios are the result of differing fractions of coarse and fine tailings on the sites. In the final leachates, the solid to liquid ratios of the samples were 0.17 (±0.1) g/ml. The pH of the surface water and the leachate was determined with an I.L. Portomatic pH meter. All the tailings samples were homogenized in a mortar and brought to dryness at 75 to 85°C. Approximately 0.5 g of tailings were

Jan 1, 1981

By W. E. L. Minter

Discussion by R.W. Hutchinson Minter's excellent recent paper (1990) on the great paleoplacer gold deposits of the Witwatersrand and its subsequent discussion (Cheney, 1991) and reply (Minter, 1991) provide an informative, interesting and up-to-date review of the geology of these unique ores and some long enigmatic questions regarding their origin. Clearly summarized by Minter (1990) are the compelling sedimentologic and stratigraphic relationships indicating that the Central Rand Group conglomerates are ancient placers and documenting the fluvio-deltaic conditions of their transport and deposition. As Minter (1991) indicates, Cheney's discussion broadens Minter's 1990 coverage of the subject by considering higher and lower stratigraphic units and by adding detailed comments concerning recently published information about metamorphic and age relationships. Cheney's discussion and Minter's reply also readdress the old controversy of epigenetic hydrothermal vs. syndepositional placer origin for these deposits. This controversy has been resurrected by: • recent recognition of hydrothermally-altered granites (HAGS) in the older Archean basement rocks that lie unconformably beneath the Dominion Group rocks north and west of the Witwatersrand depository; • recognition of greenschist metamorphic assemblages in the Witwatersrand strata; and • the presence of interpreted epigenetic mineral assemblages and textures in some of the deposits. These relationships are briefly discussed by Cheney who suggests they may result from later, superimposed metamorphism and deformation and do not prove that the gold was introduced by epigenetic/metamorphogenic processes. In his paper, Minter (1990) cited the 1986 abstract of a subsequently published paper by Hutchinson and Viljoen (1988) who also considered many of these aspects and attempted to integrate them all in abroad genetic hypothesis. In addition, they emphasized the additional important problem of determining the source for the Witwatersrand gold. Although this issue was partially addressed by Reimer (1984), Mossman and Dyer (1985) and Reimer and Mossman (1990), the question has been generally under emphasized in earlier work and was, therefore, not stressed by Minter and Cheney. Reimer (1985) also emphasized the importance of weathering of the basin's Archean hinterland and its affects on Witwatersrand sedimentation. Since the epigenetic hydrothermal hypothesis was essentially discarded in favor of placerist origin, the gold source for these great deposits has generally been attributed to the weathering of lodes in greenstones or granites of the uplifted, older Archean hinterland to the north and west. However, Hutchinson & Viljoen (1988) present evidence that this explanation is inadequate, as well as data in support of an alternative explanation. They suggest that the gold and accompanying abundant, clearly detrital and auriferous pyrite in the conglomerate reefs were derived by erosional degradation of auriferous-pyritic exhalite previously deposited, by shallow marine discharge of hydrothermal fluids, along the fault-bound northwestern margins of the Witwatersrand depository. The auriferous-pyritic exhalites were generated by fluid-rock reactions in the subsurface, particularly in the highly-altered lavas of the Dominion Group but also in adjacent basement granitic rocks. The process envisaged is comparable to that observed in sea floor hydrothermal systems today, although, in this case, it occurred at the margin of a rapidly subsiding, shallow marine or continental basin. Important evidence for this explanation is the anomalous gold content of the ferruginous, shaley strata occurring throughout the Witwatersrand Supergroup and including the distinctive contorted bed that is an iron formation. These layers have been interpreted (Hutchinson and Viljoen, 1988 and 1990) to represent the more distal, finer-grained, mixed chemical/clastic sedimentary strata. Thus, they are the basinal equivalents of the proximal, auriferous-pyritic exhalites that were deposited along the basin's margin and subsequently reworked by sedimentary processes. This gold source explanation resolves many of the enigmatic questions regarding Witwatersrand geology and the reawakened controversy between proponents of hydrothermal and placerist genetic hypotheses. The theory invokes a hydrothermal origin for the gold in the basin-margin pyritic exhalites, thus explaining the visible hydrothermal characteristics (Figs. 1 and 2). It also provides compelling evidence for placer origin by encompassing all of the fluvio-deltaic processes of clastic sedimentary transport and deposition that are clearly summarized by Minter. These characteristics result from the degradational reworking of the pyritic exhalites along the depository's margins. Fluvial reworking, transport and deltaic redeposition of this detritus, along with additional detritus carried into the depository from the hinterland, then formed the conglomerate reefs. Other enigmatic aspects of Witwatersrand geology include: • the rarity of magnetite and ilmenite (the two most common heavy minerals in placer deposits) and the contrary abundance of leucoxene in the conglomerate reefs; • the presence of differing varieties of pyrite (authigenic, allogenic, compact and porous) all of which are auriferous; and • the presence of well-rounded pebbles, even cobbles, of pyrite that, in view of the brittleness of the mineral, could not have been transported great distances from a hinterland.

Jan 1, 1993

By Chester A. Rowland, David M. Kjos

INTRODUCTION Mineral ore comminution is generally a feed preparation step for subsequent processing stages. Grinding, the fine product phase of comminution, requires a large capital investment and frequently is the area of maximum usage of power and wear resistant materials. Grinding is most frequently done in rotating drums utilizing loose grinding media, lifted by the rotation of the drum, to break the ores in various combinations of impact, attrition and abrasion to produce the specified product. Grinding media can be the ore itself (autogenous grinding - primary and secondary), natural or manufactured nonmetallic media (pebble milling) or manufactured metallic media - steel rods, steel or iron balls, or a combination of autogenous media and steel balls (SAG milling). This chapter covers rod and ball mills utilizing manufactured metallic grinding media. MILL DESIGN The interior surface of rod and ball mills exposed to pulp and/or grinding media are protected from wear and corrosion by rubber, metallic or a combination of rubber and metallic wear resistant materials. Rod and ball mills essentially draw constant power, thus are well suited for use of synchronous motors with power factor correction capabilities as drive motors. A net of approximately 120 to 130 percent of running torque is required to cascade the charge in these mills. The pull-in torque is about 130 to 140 percent with the pullout torque to keep the motor in-step (in-phase) generally in excess of 150 percent. When rod and ball mill are started across-the-line the starting and pull-in torques result in inrush currents exceeding 600 percent which possibly result in high voltage drops. To deliver 130 percent starting torque to the mill the motor design must take into account the maximum anticipated voltage drop. Motor torque decreases as the decimal fraction of the voltage available squared. E.g., a motor rated 160% starting torque with a 10% system voltage drop will deliver 160% x or 129.6% torque to its output shaft When it is not possible or practical to start a fully loaded synchronous motor across-the-line it is possible to utilize the motor's pull- out torque to start the mill. By using a clutch, normally an air clutch. between the motor and the mill, the motor is brought up to synchronous speed before the clutch is energized. If the motor has an adequate amount (175 or greater) of pull-out torque the pull-out torque starts the mill without major disruptions on the electrical system. Since the energy release at initial cascade of the mill charge is an inverse function of acceleration time, a minimum acceleration time of 6 to 10 seconds or more is recommended to prevent damage to the mill or the mill foundation. Economics at the time of plant design and mill purchase determine the drive to be used. The simpliest drive is the low speed synchronous motor with speeds in the range of 150 to 250 RPM connected to the mill pinionshaft by either an air clutch or flexible coupling. Using a speed reducer between the motor and pinionshaft permits using motors having speeds in the range of 600 to 1000 RPM. In this speed range, if power factor correction is not required induction motors can be used; squirrel cage where there is no restriction on inrush current; slip ring where a slow start and low inrush current is required. Air clutches can also be used to ease starting problems with squirrel cage motors. In some areas of the world induction motors and starters are less expensive than synchronous motors at a sacrifice of motor efficiency and power factor correction. Dual drives, that is two pinions driving one gear mounted on the mill, become economical for ball mills drawing more than 3500 to 4000 horsepower (2600 to 3000 kilowatts). Further developments of the low frequency, low speed synchronous motors with the rotor mounted on the mill shell or an extension of one of the mill trunnions could improve the cost picture for these "gearless drives", making them practical for large ball mills. The percent of critical speed, which is the speed at which the centrifugal force is sufficiently large to cause a small particle to ad- here to the shell liners for the full revolution of the mill is given in mill specifications. Critical speed is determined from the following: Where D is mill diameter inside liners (specified in meters). Cs is critical speed in RPM. When D is specified in feet

Jan 1, 1998

By Fritz Eder, Rick Hendrickson

The quantities requires decisions growing demand for large of oxygen by gold smelters today that economic and operational be made regarding their selection providing electrical power, water, communications, sewage facilities and access roads. Liquid storage and supply system is of the system. decisions most appropriate oxygen supply Key factors affecting such are discussed in the following.

Jan 1, 1990

By Charles A. Horne

Grinding mill circuits used for particle size reduction of mineral ores commonly use cyclones as primary classifiers. Typically, several individual cyclones are installed in a cluster (Fig. 1) where they can easily be added or valved-out of operation in order to balance classifier capacity with fluctuations in tonnage and recirculating loads as ore grades and hardness vary.

Jan 1, 1993

By Marcos C. Filgueiras, Thomas A. Post, Michael A. Giralico, Daniel M. Adams

The leaching of copper, gold, and nickel in tanks requires mixing. Minerals require oxygen, acid and/or base [NH3] to assist in the leaching process. Two basic types of tanks are used for this operation. They are either vertical tanks or closed horizontal tanks called autoclaves. This paper discusses mineral leaching, it's mixing requirements, and autoclaves.

Jan 1, 1999

By L. W. Cope

Cuba is a mineral rich area, and the Cuban government is encouraging mining investment in the country. Joint ventures with government entities are encouraged. This paper will give some insights into the laws and regulations, and the agencies to contact for investment and development. The present-day situation of the US sanctions against Cuba will be covered.

Jan 1, 2004

By H. Z. Kuyumcu

In order to ensure a sustainable development in the mineral industries it is very important to reduce the process water consumption in mineral processing. Based on a systems analytical approach this paper deals with the most important parameters of process water management during plant operation and indicates strategies for reducing the water consumption in mineral processing.

Jan 1, 2003

By B. Suresh, Kalyan K. Das, Pradip

A series of salicylaldoxime derivatives with alkyl group substitution in the main chain and the side chain were synthesized and evaluated for the flotation of malachite, cerussite and smithsonite. The effect of chain length and the position of the substituent group on the selectivity of separation amongst oxidized copper, lead and zinc minerals are discussed in this paper.

Jan 1, 1995

By D. Royston

A novel low-cost technology is described that treats excavation waters in estuarine environments where water coloration due to humic material is present, along with acidity, turbidity, sediment and salinity. The process treats all the components in the water to produce a clear (color-free) water stream that meets requirements for direct discharge to local estuarine waterways.

Jan 1, 2003

By W. J. Halvorsen

Means for minimizing the disadvantages of thermal drying are suggested. The other ap¬proach of substituting other techniques in place of thermal drying is also discussed. Recent devel¬opments in fine coal screening dry down to 3.2 mm (0.125 in.) and 2.0 mm (10 mesh) offer an econom¬ical means in certain cases.

Jan 1, 1988

By T. N. Singh, M. M. Singh, R. B. Singh

Fly rock is common when blasting shallow holes and during secondary blasting. Although the required quantity of explosives for secondary blasts is less, noise and fly rock can have an enormous environmental impact. This paper mainly deals with field experiments on blast-design parameters and addresses some precautionary measures that can be taken when pop shooting.

Jan 1, 2000