Search Documents

By Peijian Zhang, Yansheng Liu, Yuusaku Tominaga

The directions for ventilation control are often given in linguistic styles such as "if the airflow rate measured is small, a high value of rotation on a local fan should be chosen." In order to control the underground climate using a computer instead of a human being, both the reliability of data values measured underground and the application of human recognition of data values are required. The efficiency of data transmission is dependent on a method of checking a signal which is changed by mixing noises resulting from cases of electrical and mechanical damage to cables. In the study, fuzzy reasoning is adopted to choose a checking method for underground conditions from a normally operating state to an emergency. Fuzzy reasoning is applied to control airflow rate under the linguistic control rules given. It is shown that an effective series of linguistic control rules derived by fuzzy-sets theory is available in ventilation control when used in conjunction with an air velocity sensor, a computer and a local fan with thyristor control. Moreover, a system to make an optimum series of linguistic control rules for ventilation control is introduced.

Jan 1, 1987

By I. K. Kapageridis

Digital photography combined with three dimensional models of topography, mining operations and restoration plans can lead to extremely realistic images and animations of the current and future states of a mine or quarry. The amount of work and the time required for the successful modeling of a mine and its restoration plan are surprisingly low nowadays. All this means that the visual impact of mining and quarrying operations can be easily assessed using common computer hardware and some dedicated software packages. LAVA Mining and Quarrying SA is a company committed to strive continuously for the highest possible environment protection at the company?s quarries. The pozzolanic rock quarry located at Xylokeratia is one of the company?s quarries on the island of Milos and the subject of the study presented in this paper. A thorough restoration plan of the Xylokeratia quarry is being completed by the company. For its purposes, a complete visual impact assessment study was performed at the Department of Geotechnology and Environmental Engineering of the Technological Education Institute of Western Macedonia. The procedures used in this study and the produced visual results are presented in this paper.

Jan 1, 2006

By P. T. Bissert, J. P. Ducarme, J. D. Noll, C. C. Jobes

"There have been about 42 fatalities in underground coal mines between 1984 and 2015 where the victim was struck, pinned, or run over by a mobile machine (MM) such as a shuttle car, scoop, or battery hauler. MSHA has issued a proposed rule requiring proximity detection systems (PDS) on MMs in an effort to prevent future fatalities. Currently approved PDSs use electromagnetic (EM) technology to detect the presence of a miner and impose machine controls to prevent contact. The disadvantages of an EM-based PDS on MMs include the need for a miner-wearable component (MWC), environmental interferences, EM interferences from other devices, and low localization range and accuracy. NIOSH researchers are investigating alternate technologies that could improve the capabilities of the current PDSs. Many technologies were reviewed, and NIOSH researchers identified RFID, LIDAR, RADAR, ultrasonic detection, and computer vision as candidates for PDS development. The performance characteristics of each technology and its applicability to an underground mining environment will be discussed, along with international developments and implementations, and the concept of sensor fusion. INTRODUCTION PDSs provide safety to mine workers by detecting their presence (and in some cases location) around a machine. These PDSs provide a warning zone, which triggers an alarm, and a stop zone, which halts the machine before it contacts the miner. The Mine Safety and Health Administration (MSHA) issued a final rule requiring that PDSs be installed on all continuous mining machines (CMMs) on the working section, with the exception of full-faced machines, according to a phase-in schedule for newly manufactured and existing equipment [1]. The PDSs that were designed for CMMs have since been adapted to other mobile machines. Mobile machines include scoops, which are used as general utility vehicles, as well as coal hauling machines, such as shuttle cars, ram cars, and continuous haulage systems. MSHA has examined all accident reports from 1984 to 2014, and determined that 42 fatalities could have been prevented on mobile machines had a PDS been installed [2]. As such, MSHA issued a proposed rule that would require mobile machines on working sections (with the exception of longwall sections) to be equipped with a PDS. This rule would follow a phase-in schedule for newly manufactured and existing equipment. Currently available PDSs are based on electromagnetic (EM) technology. NIOSH researchers developed a shell-based magnetic flux density distribution model [3] for determining the position of a miner near a machine. A typical system would consist of four generators positioned around the perimeter of the machine. Each generator is a coil of insulated wire wrapped around a ferrite core. The magnetic field strength is proportional to the current running through the coil. Miners working on the section have an MWC, which is a transceiver that measures the field strength emitted by the generators and transmits a data packet over an RF link which contains the field strength reading to the PDS controller mounted on the machine. The magnetic field generators are pulsed sequentially such that the MWC can identify which generator’s field strength it is reading. This type of system utilizes the principle of magnetic flux density: the closer the MWC is to the field generators, the higher the field strength reading. Thus a miner’s presence can be determined once he gets too close to the machine, because his MWC will measure a magnetic flux density beyond a certain threshold. These thresholds are utilized on a per-generator basis to “shape” the fields for both warning and stop zones around a machine, as illustrated in Figure 1."

Jan 1, 2017

By W. A. Crosby, A. Bauer

The recent increase in size of open-pit mining operations has resulted in major improvements in efficiency that are beneficial to the mining industry. Higher bench heights, larger diameter blast-holes, and more powerful explosives have played an important part in reducing mining costs. These measures have, however, resulted in increased energy concentrations in the blast area, which can result in severe backbreak problems for final pit walls. If backbreak is not controlled, a decrease in the overall pit slope angle will ultimately be necessary, and consequences, such as decreased recoverable ore reserves and increased waste-to-ore ratios, will result. Greater amounts of loose face rock will be produced, and planned safety berms will be less effective or nonexistent. Hazardous working conditions can also result. Remedial measures, such as scaling large areas and using wire mesh or other artificial support, are very expensive and difficult to implement. There must be a trade-off between the money saved by using larger blasts, and the time spent to maintain pit wall quality. The best approach is to control blasting effects so the inherent strength of pit walls is not destroyed. Presplit and trim blasting are two control blasting techniques used to accomplish this. Both techniques are designed to create a low explosive energy concentration per unit of wall area at the perimeter of the pit. Energy concentration of the main production blast must also be controlled to avoid damaging the final pit wall. A low-energy concentration at the final wall can be obtained by decoupling charges, decking charges, using less powerful explosives, decreasing blasthole diameters, and changing the burden and spacing. Rock properties-fragmentation and the final state of the pit wall-influence the success of a blast. The most important properties to consider are: in situ rock strength, and the nature, frequency, and orientation of structural features. Since these variables cannot be controlled, they must be evaluated by suitable field tests, and then a control blast can be designed using controllable variables, such as spacing, burden, and hole diameter, so the blast will be successful for appropriate rock conditions. One main thrust of this article is to show how control blasts can be successfully designed for larger hole sizes, up to 381-mm-diam. While efforts to produce a good control blast in shovel/truck pits have been ongoing for some time, recent use of a modified presplit technique in dragline operations has helped reduce water problems, improve safety, and increase dragline productivity in a number of surface coal mines. This article presents examples on designing and using presplit and trim blasting for large hole operations in both shovel/truck and dragline mines. Presplit Blasting As introduction to presplit blasting, Fig. 1 illustrates a typical presplit blast layout using 102 mm-diam presplit holes for 381¬mm-diam production holes. For this type of blast, presplit holes would normally be drilled first, ahead of main production holes. The choice can then be made between loading and firing the presplit line or infilling the main blast. In the latter case, the presplit line would be fired instantaneously 100-150 milliseconds before the main blast. As shown in the figure, the presplit line is formed ahead of the main

Jan 2, 1982

The Sandvik Group (Sandvik AB), headquartered in Sandviken, Sweden, continues to expand its worldwide operations growth. After recent acquisitions, including Tamrock, headquartered in Tampere, Finland, the company now has annual sales of more than US$5 billion (SEK 40 billion). With the acquisition of Tamrock, Sandvik has further increased its interests in the mining industry. Sandvik Rock Tools, a familiar name in the mining industry, is one of the world's leading suppliers of rock-drilling tools. And Tamrock is one of the world's leading suppliers of drilling machinery, loaders and equipment for rock-excavation operations. Sandvik believes that the two companies combined offer customers "maximum productivity through total system solutions, including machinery, service and tools." In 1997, Tamrock posted sales of US$940 million (SEK 7.5 billion). In addition to its expertise in drilling tools and equipment, Sandvik is supported by its collective resources in specialty steel and cemented carbide. These resources include extensive research and development capabilities, with annual investments in R&D now at about US$150 million. As a result of the R&D programs, internal expansion and acquisitions, the company has nearly doubled in size during the past four years. From 1994 to 1997, nearly US$1 billion was invested in internal growth and another US$825 million has gone towards acquisitions. Return on net assets is now 22% annually. In addition to Tamrock, acquisitions of interest to the mining community include Drillmaster Inc., Houston, TX. The acquisition of Drillmaster (by Sandvik Rock Tools) has further strengthened Sandvik's position in down-the-hole drilling tools. Other major recent acquisitions by Sandvik include Kanthal, a Swedish manu¬facturer of metal and ceramic-resistant materials for electric heating furnaces, household appliances and elec¬tronics, and Precision Twist Drill, Crystal Lake, IL, one of the leading producers of high-speed cutting tools. With more than 38,000 employees worldwide, the Sandvik Group is divided into six separate business areas. Each area is responsible for its own R&D, production and sales: ? Sandvik Mining and Construction. Including Tamrock and Sandvik Rock Tools, this business area boasts of offering the most comprehensive range of "rock-working" products. These include drilling rigs, loaders, rock-excavation equipment and rock drilling tools. ? Sandvik Specialty Steel. This area includes Sandvik Steel and Kanthal, manufacturers of stainless steel tube, strip wire and bar, as well as high-alloy steel and specialty metals. ? Sandvik Tooling. This business area consists of tools and tooling for metalworking applications. Sandvik Coromant is a market leader in the development, manufacture and marketing of tools using cemented carbide, ceramics and extremely hard materials, such as diamond and cubic nitrite. CTT Tools is the world's largest manufacturer of high-speed steel tools and is now expanding operations into solid cemented-carbide tools. ? Sandvik Hard Materials. This segment produces a full range of "hard materials," ranging from cemented carbide to diamond. This area manufactures and markets a full range of cemented carbide blanks for tool manufacturers, as well as components and rolls. ? Sandvik Saws and Tools. This business area manufactures high-quality handsaws and metal saw blades, as well as hand tools ranging from wrenches to chains for logging machines. ? Sandvik Process Systems. This segment manufactures steel belts, process systems and automatic sorting systems for the chemical

Jan 1, 1998

Conveyor belting-Dunlop Belting Division has published a manual on its Starflex plied conveyor belting. The design section of the manual contains advice on the calculation of tensile strength and horsepower needs while the section on belt selection offers helpful recommendations. Circle 200 on reader service card Hydrostroke feeders-A pamphlet from Kone Corp. highlights the uses and operating principles of its hydrostroke feeders. Circle 201 on reader service card Electric cylinders-A 24-page catalog from Raco International Inc. describes applications for its electric linear actuators in addition to the electronic options for computer - controlled operation. Circle 202 on reader service card High torque drives-T. B. Wood's Sons Co. offers a 56-page booklet providing features and specifications on its high torque drives. Information includes a step-by-step drive selection proce¬dure. (HTD) Circle 203 on reader service card Sludge depth meter-The model 600 sludge-depth meter that locates the sludge bed in clarifiers and settling tanks is described in a four-page bro¬chure from Markland Specialty Engineering Ltd. (600-84) Circle 204 on reader service card Cavity pumps-An eight-page bulletin is available from Robbins & Myers Inc. It features the application of Moyno progressing cavity pumps in handling composite slurry fuels. (400) Circle 205 on reader service card Roller chain-A roller chain catalog shows heavy duty drive chains and other specialty conveyor chains. It is available from Peer Chain Co. (PC200) Circle 206 on reader service card Belt filter-Phoenix Process Equipment Co. has available a pamphlet detailing its belt filter press. The unit is designed to dewater refuse and clean coal, yielding easily handled dry filter cakes. Circle 207 on reader service card Capabilities - Literature from International Mineral Services Ltd. highlights its services and capabilities to the mining industry. Circle 208 on reader service card Motor analysis - How to select the proper electric motor by comparing life cycle costs, power costs, rate of return, and other factors, is described in a brochure from Westinghouse Electric Corp. (SA-11376) Circle 209 on reader service card Cavity pumps - A product application data sheet is available from Robbins & Myers Inc. It details the use of Moyno positive-displacement, progressing cavity pumps in handling ground limestone slurry. (PC-21) Circle 210 on reader service card Dust collectors - "Dust Collector Selection Guide," from American Air Filter, describes dry mechanical collectors, wet collectors, fabric collectors, and electrostatic precipitators. (CAD-1-901G) Circle 211 on reader service card Wet scrubber - A 12-page bulletin from The Ceilcote Co. provides a comprehensive description of its ionizing, wet-scrubber system. (12-19) Circle 212 on reader service card Metric o-rings-Simrit Corp. has published a 16-page brochure detailing its full line of standard metric o-rings. Information includes graphics and dimensional charts, and specific data on materials and application ranges. Circle 213 on reader service card Hearing protection - A 16-page catalog from Cabot Corp., EAR Division, provides information on its hearing protection devices and noise control products. Circle 214 on reader service card Toxic gas detection - Sensidyne Inc. is offering a guide for toxic gas monitoring. A description of the electrochemical sensors, as well as ranges, complete specifications, and interference charts are included. Circle 215 on reader service card Hydraulic bolting systems - Ingersoll-Rand Co. is offering a brochure on its line of hydraulic bolting systems. These systems, hydraulic wrench and power console, are designed for heavy duty bolting applications. Circle 216 on reader service card Temperature monitoring - A brochure describing the Ramsey Engineering Co.'s micromonitor temperature monitoring system is available. Three types of switches are available for monitoring bearing temperatures. (80.300) Circle 217 on reader service card Product catalog - Shadbolt & Boyd Co. has published a product catalog. Among items described are hoist slings and cranes; compressors; hydraulics; wire rope, chains, and fittings; and materials handling and shop equipment. Circle 218 on reader service card Cylinder controls - A 12-page booklet presenting Hanna Corp.'s line of electrical controls for cylinders is available. It features proximity and limit switches for hydraulic and pneumatic cylinders, and standard and 3-amp reed switches for pneumatic cylinders only. (550) Circle 219 on reader service card Slurry pump - Pettibone Corp. has published a 24-page booklet covering its heavy duty pumps made with 'diamond alloy' materials for handling slurries of abrasive materials. Circle 220 on reader service card

Jan 9, 1985

By Peter J. Szabo

The mining executive works in a cyclical industry. His employment is subject to the vagaries of the marketplace. Boom and bust has always been the industry's story. "Big oil" failed in its mining effort. This left emotional and financial scars on many mining families. One must remember that mining executives always play a high-stakes game. Given the cyclical nature of the mining industry, mining executives need to take care of their own financial security. The mining executive that does not plan for his financial security in this cyclical business is playing Russian Roulette with his future. Take a look at those people who have reached their later years with the mining industry. One usually finds three categories of people. Those few in the first group have been fortunate enough to have worked for one company. They have survived the winnowing process of cyclicality, political problems, and takeovers. They have reached normal retirement age. For them, the retirement years are usually comfortable. People in the second group have worked for those same mining companies. But these people have been forced out by early retirement. Or they have been laid off for cyclical, takeover, or political reasons. The third group includes those who have held many positions in the mining industry. Probably not until their later years are they fully vested, if at all, in a pension program. The first small group, then, is the exception. The others, unless they have taken care of their financial security, are doomed to later years of financial problems, stress, and unhappiness. Too late in life, many realize the harsh realities of failure to plan and implement a personal financial program. Mining executives go to some of the world's leading mining schools, to learn how to make money. The curriculum is technically strong. Most mining graduates are familiar with the intricacies of discounted cash flow, present value, and the Hoskold formula. But few of these same mining schools require courses on personal financial planning. Such courses could give mining students a realistic foundation and the mechanisms with which to cope with their cyclical profession. An executive has only three sources of money. He can make money at work. He can put his money to work. Or he can get money from charities, such as government programs. Of these three sources of money, money at work has the best chance of providing financial security in later years. The mining executive must think of the day when he will be too old to work and contribute to the market place. At this point, the quantity and quality of his investments will determine whether his later years will be secure. Along with the Mining Engineering Handbook, two key books should be included in the mining executive's library. These are Venita Van Caspel's The Power of Money Dynamics and Benjamin J. Stein's Financial Passages. These books contain the basic concepts of personal financial planning so critical to an individual's financial survival. Venita points out the simple formula that is the key to financial independence: Time + Money + American Free Enterprise (Rate of Return) = Opportunity to Become Financially Independent Chart 1 shows that this is not a trite formula. The chart shows the dramatic effects of compounding over time. The chart also shows at various yields what a $2000 a year Individual Retirement Account (IRA) contribution will accumulate. Chart 1 (from Money magazine) is based on the future value of an ordinary annuity. It shows that the key to amassing a small fortune by the time a person reaches his 50s is starting to save methodically in his 20s. This, coupled with the highest yields consistent with safety of principal will ensure financial security. There are significant effects from compounding money over time. Every year the decision is put off to save for later years will cost a person dearly by the time he reaches his 50s. For example, consider the decision to put off for one year a $2000 IRA investment at a 12% return. Starting it at age 31 instead of 30 will cost the executive almost $100,000 by age 65. What if the executive waits until age 35 to get started with his $2000 a year investment? He will then lose nearly $400,000 by age 65. Stated another way, the executive costs himself this $400,000 simply because he did not invest $167 a month for five years. $167 a month - that's less than an inexpensive second car payment. This $400,000 pool of money could provide the executive a $40,000 a year income at age 65, assuming a 10% return on invest-

Jan 11, 1985

By Fred Leighton

INTRODUCTION Dynamic (seismic or microseismic) methods of determining the stability of structures in rock are based on detecting and analyzing the characteristics of seismic energy that has originated from or traveled through the rock mass. This seismic energy can be in the form of naturally occurring rock noise energy resulting from structural adjustments within the rock or can be introduced into the structure by physical means, such as by blasting or impact. In either case, the seismic energy radiating through the rock mass can be detected using standard equipment and can be analyzed by established techniques to reveal a wide variety of information concerning the condition and stability of the rock mass through which the energy has traveled. In the following sections, the basic instrumentation required for seismic and microseismic studies is described, and some of the presently used applications of these methods are discussed to exemplify the state of the art. INSTRUMENTATION Seismic disturbances in a rock structure generate two types of seismic wave radiation, body waves and sometimes surface waves, which radiate outward in all direc¬tions from the source of the disturbance. Underground mining applications are generally concerned only with discerning the characteristics of the resulting body waves, i.e., the compressional (p-wave) and the shear (s-wave) energy. As these two forms of energy travel through the rock structure, the particles of the rock mass are caused to vibrate, and the vibration character¬istics resulting from each of the two types of wave are distinct. Some important differences are: 1) Compressional and shear waves travel at different velocities through the rock structure. 2) The frequency at which each wave causes particles to vibrate is different, and may range from about 50 to 100 000 Hz. 3) The amplitude or energy level of each wave is different, with the shear energy usually being the greatest. These differences form the basis for equipment se¬lection for individual studies and for modern data analysis techniques. The following sections describe the basic equipment necessary to detect and record seismic wave energy data and show several examples of analysis procedures and how these procedures have been used. In principle, seismic equipment is very simple. It consists of a geophone (or geophones) to detect the seismic energy vibration and convert that vibration to an electric signal, an amplification system to increase the level of that signal, and a means of monitoring and/or recording the signals detected. Fig. 1 is a block diagram of a typical system. The following sections offer a very brief discussion of system components and their individual functions. A more complete discussion is given by Blake, Leighton, and Duvall (1974). Geophones The function of the geophone is to detect the vibrations caused by the passing of the seismic wave energy and to convert that vibration into an electrical signal that displays both the amplitude and frequency characteristics of the vibration. Particle motion or vibration can be quantified and measured by measuring displacement, velocity, or acceleration of the particles. Thus, there are three types of geophones: displacement gages, velocity gages, and accelerometers. The choice of gage depends on the characteristic frequencies of the seismic energy to be monitored and the sensitivities of each type of geophone. In general, displacement gages are used for low-frequency monitoring (periods to 1.0 Hz), velocity gages for medium-frequency monitoring (1.0 to 250 Hz), and accelerometers for high-frequency monitoring (250 to 10 000+ Hz). Experience has shown that in underground studies, the choice of which gage to use lies between velocity gages and accelerometers. An easy, accurate method for selection of gage type is discussed by Blake, Leighton, and Duvall (1974). Once the type of geophone has been selected for use, it must be properly installed, and in the installation procedure the most important step is insuring that the gage is firmly attached to a competent portion of the rock structure. Poorly mounted geophones may entirely fail to recognize low-level seismic signals and will distort the information from signals they do see. Amplifiers Seismic events associated with mine structures occur over a very broad range of energy which results in a broad range of geophone output levels. In general, geophone output levels occur in the microvolt to low milli-volt range, and it is necessary to amplify these signals in order to drive recording or monitoring equipment. Because either an accelerometer or a velocity gage might be used as the geophone, the amplification system must

Jan 1, 1982

By D. J. Brunner, S. Mathur, D. McKinney

With the advent of faster micro-processors, the use of numerical methods to simulate complex fluid dynamic phenomena in three dimensions for use in design has become prevalent in the automotive, and turbo-machinery industries. The Computational Fluid Dynamics (CFD) method divides the region of interest into small control volumes which form the mesh representing the physical characteristics of the problem, and uses the finite volume method to intergrate the equations for the conservation of mass, momentum, energy and species over each control volume. Recent developments in CFD software expedite mesh generation, and enable the use of unstructured grids, comprised of tetrahedral volumes in three dimensions and triangular areas in two. CFD more accurately represents complex geometries and allows for relative movement of meshes enabling simulation of multiple moving bodies. 'ibis paper presents two examples of how CFD simulation can be used to assess mine and tunnel ventilation problems formerly addressed by application of analytical solutions which were developed assuming ideal incompressible conditions. CFD simulation is used to evaluate the impact of varying the airflow in a descentionally ventilated airway on the layering along the roof of smoke and hot gases resulting from a vehicle fire. Control of the smoke layer is required to enable safe egress from the vehicle, particularly if the vehicle is for personnel transport, and to ensure control of the fire contaminants throughout the ventilation system. The airflow required to prevent layering against the ventilation direction, calculated from the Bakke and Leach relations (Bakke and Leach, 1962), is compared with the CFD simulation results. An evaluation of the pressures, generated as a vehicle enters a tunnel portal, using CFD simulation, is also presented for unflared and flared portal configurations. These simulation results are compared with predictions derived using an analytical method which assumes one-dimensional and incompressible flow. Results of the CFD simulation are presented in an animated video format. SIMULATION OF BACKLAYERING In designing a ventilation system for a transit tunnel, the ability of the ventilating air to control and prevent backlayering of smoke and hot gases resulting from a vehicle fire is of prime concern. The buoyant nature of hot smoke causes it to rise relative to the colder, fresh air provided by the ventilation system. If the vehicle fire occurs in a descentionally ventilated tunnel, the smoke may tend to move upgrade in a layer above the incoming ventilation airflow. The layer may become thick enough to engulf a substatntial part of the tunnel cross-section upgrade of the incident that comprises the evacuation route. This effect is termed "backlayering' and it is similar to the development of methane layers in mines for which most studies related to backlayering have been done. Prediction Techniques Analytical A number of studies have been conducted (Bakke and Leach, 1962) to define the characteristics of this phenomena and as a result have produced relations which are used both in the mine and transit ventilation fields to define the air velocities required to control layering. In the transit industry the air velocity required to prevent the backlayering phenomena from occuring during a vehicle fire is called the "critical velocity" (Associated Engineers, 1975) and is dependent upon a number of factors: tunnel height, cross-sectional area and grade; ambient air temperature and density; and the heat release rate of the fire. Common practice in transit ventilation design is to provide an airflow which meets or exceeds the critical velocity. In order to determine whether or not the critical velocity can be achieved with a particular ventilation system, a one-dimensional simulation of the tunnel network is typically performed using programs such as the Subway Environment Simulation program (SES) originally developed in the late 1970's (Associated Engineers, 1980). The results obtained from SES are compared to the critical velocity to determine the adequacy of the ventilation system. Computational Fluid Dynamics For the backlayering simulations, a commercial CFD code which has been used successfully in a wide variety of engineering applications, was used. It provides numerous options for modeling laminar and turbulent flows, multiple turbulence models, definition of multiple species and chemical reactions between them, a variety of boundary conditions (including constant pressure and constant velocity inlets) and the ability to apply user-defined FORTRAN subroutines. It includes the ability to model conductive, convective, and radiative heat transfer. FLUENT also permits the use of "body-fitted coordinates" to match the computational mesh or grid to complex real-world geometries. Computational Fluid Dynamics Model The model developed to simulate the backlayering phenomena is comprised of an airway of rectangular cross-section, 4 meters wide, 4.5 meters high, and 200 meters long. A laterally

Jan 1, 1995

By S. K. Mohanty, T. M. Dittrich, M. J. Allen, M. Dardona, A. C. Strzelecki, J. Hovey, Boukhalfa. H.

Rare earth elements (REEs) have many critical uses in advanced technology and the lack of a reliable domestic supply has been identified by the US DOE as a vulnerability to US economic security. Our research focuses on developing an economical process for extracting REEs from coal fly ash and power plant wastewater sludge by coupling a hydrothermal extraction process with the engineering of a ligand-associated media for concentrating REEs from the extraction liquid. Ash samples have been collected from two Detroit-area Power plants that burn 100% low sulfur coal (Trenton Channel) or fuel blends of 75% low sulfur coal and 25% high sulfur coal or 70% low sulfur coal, 15% high sulfur coal, and 15% petcoek (Monroe Power Plant). Ash samples are then subjected to hydrothermal conditions from 100-350 °C for 1-24 h at Los Alamos National Laboratory and leachate concentrations are measured by inductively coupled plasma-mass spectroscopy (ICP-MS) and compared to hydrofluoric acid digestion results. Experiments designed to aid in ligand selection and loading optimization show that di-(2-ethylhexyl)methanediphosphonic acid (H2DEH or DIPEX™) can be successfully loaded to a commercially available swellable organically modified silica (SOMS) media. Preliminary results show that DIPEX-associated SOMS surface loading can exceed 4x on a mass/mass basis and in simplified sorption experiments with Nd solutions (~pH 2), the DIPEX-SOMS media can sorb >90 mg Nd per g of media. Recovery of the sorbed Nd with low pH solutions has had low efficiency with the high (4 g DIPEX/ g dry media); however, near complete recovery was achieved with lower surface loadings (0.05 g DIPEX/ g dry media). Column experiments are being conducted to evaluate the optimal ligand/media ratio for repeated use. Completive sorption with Fe and other major cations are also being evaluated.

Jan 1, 2019

By H. Nagel, A. P. Schissler

"INTRODUCTION Anadarko Petroleum Corporation (Anadarko) owns a region of oil shale properties acquired as part of the original Union Pacific Land Grant of the 1800’s in southern Wyoming. These holdings are greater than 2 million acres and occur throughout the Green River Formation in southwestern Wyoming. One area was prioritized for further study by Anadarko Minerals called the Kinney Rim in the Washakie Basin due to low environmental impact, proximity to infrastructure, high ore grade, and low mining cost. The area is a low-overburden oil shale resource that can be developed using surface mining methods, processed by conventional surface retort, and placing waste rock disposal back on the bench for a design capacity of 10,000 barrel per day. The purpose of this papers is to present the results of environmental analysis and timeline, the mine plan, and surface ore processing to offer a resource-ready energy source.Mineral rights for the Kinney Rim area are owned by Anadarko, the United States Bureau of Land Management (BLM) and the State of Wyoming. Mining of oil shale for this study targets Anadarko owned mineral resources.GEOLOGY The study area is in the Green River and Washakie Basins in western Wyoming. The host geologic member is the Laney Oil Shale. Figure 2 illustrates the Laney shale within a generalized lithologic cross section.OIL SHALE LEASING The proposed Kinney Rim oil shale mining project is located in an area dominated by a 1 square mile checkerboard landownership pattern with every other section typically administered by Bureau of Land Management (BLM) and Anadarko. Surface and mineral ownership is a split estate legal entity. The immediate Kinney Rim mine plan is all on Anadarko sections."

Jan 1, 2015

By Neil E. Izatt, M. Andre de Ruijter, Ronald L. Bruening, Wesley Young

IBC Advanced Technologies, Inc. has developed ligands, ?amed SuperLig®, which have specific applications in the gold mdustry. These ligands use molecular recognition technology (MRT). One ligand has been developed to selectively recover gold and silver from tailings solutions and from pregnant Merrill-Crowe solutions. Another ligand removes free cyanide, _ th10cyanate, other cyanide species, as well as copper and other base metal cyanide complexes from leached gold-ore solutions. The development of these "species selective'' SuperLig® prod­ucts allows for the more efficient operation of gold recovery processes and opens up the possibility of the economic devel­opment of high-copper gold ores. The resulting gold eluate is a high grade and a high purity stream which will simplify the need for further refming. Engineered systems based on MRT consist of a few unit operations utilizing standard equipment and mate­rials of construction. The process is simple to operate, thereby lending itself to automated modular design, which is both eco­nomic to manufacture and to operate. Test results for the gold and cyanide-copper systems are presented in order to demonstrate the high selectivity and effi­ciency of MRT technology in recovering these species from solution. . IBC Advanced Technologies, Inc. (IBC) and Fluor Daniel, Inc. formed a strategic alliance in late 1994. The goal of the alliance is to combine IBC's scientific expertise in the MRT field with Fluor Daniel's engineering capabilities in the metal­lurgical industry. IBC has its headquarters in American Fork, Utah, USA, where research, development and manufacturing are conducted. Fluor Daniel is an international engineering and construction firm with head offices in Irvine, California, USA. Engineering efforts for the alliance are centered in the Fluor Daniel Mining and Metals Operating Company office in Vancouver, B.C., Canada.

Jan 1, 1996

By Ronald J. Searle, Howard S. Latham

In April 1964 the Bureau of Reclamation awarded the first contract for rapid machine excavation of a water conveyance tunnel . Since then the Bureau has excavated seven tunnels with a total length of over 190,000 feet utilizing rapid excavation tunneling machines. Tunnel bored diameters have varied from 9' 0" to 20' 10" (See Table #1) and tunnel lengths from 5,000 feet to 67,000 feet. Driver and cutter units varied from 43 rolling teeth and eight rolling discs mounted on a rotating head driven by five 200 HP 23,000 volt electric motors to 20 discs and one tricone unit mounted on a rotating head driven by two 100 HP 440 volt motors. All tunnels were driven with a laser beam guidance system governing both line and grade. Trailing conveyors and rail haulage systems were used to dispose of the excavated material. Approved Bureau of Mines diesel locomotive engines for waste trains were prevalent power sources supplemented by battery units on some projects. Sandstone, conglomerates, agglomerates, siltstone, shale, and granite were the geological formations encountered, with sandstone and shale the preponderant material . Tunnel support systems utilized were structural steel ribs; rock bolts and metal plates; and shotcrete, or combinations of these. Progress varied from 51-1/2 feet to 154 feet per working day for three shifts, depending on rock material and supports required. One contractor established a record rate of advance of over 400 feet in one day, 1,905 feet in one week, and 6,848 feet in one month. Such diversified experience in underground machine excavation methods presented an excellent opportunity to observe, analyze, and evaluate associated environmental health problems. Also, to develop measures for controlling

Jan 1, 1997

By Sheldon P. Wimpfen

Man is a short time resident of the planet Earth. He does not have the memory to fully comprehend just what is going on. His span of knowledge can be related to the life of the world to see that this is the case. A museum at Grand Canyon features a geologic clock that compresses Earth's age of 4.5 billion years into 24 hours. Man's estimation of the earth's age has changed radically in the past half century. In 1930, one prominent geologist asserted that the age of the Earth was ". . . at least 600 million years." Later, physicists used radioactive clocks to conclude that the Earth's age was 1.6 billion years. More recently, geologists have found rocks in northwestern Australia estimated to have formed 4.5 billion years ago. As we learn more about what is underfoot, the estimate of Earth's age might change again. The Grand Canyon's 24 hour clock shows that the dinosaurs were the dominant life form for 165 million years. Then an event occurred that wiped them out about 65 million years ago. The prevailing theory is that an asteroid struck the Earth and generated enough dust to wipe out the vegetation upon which most dinosaurs fed. During Earth's existence, there have been at least 12 such mass extinctions - the worldwide disappearance of diverse animal groups. On a planet that has been around for 4.5 billion years and that may continue to exist for another 4.5 billion, it seems reasonable to expect that further mass extinction's will occur. According the Grand Canyon's 24hour clock, the 165 million year reign of the dinosaurs amounted to about five minutes. On that 24 hour clock, the world has been dinosaur free for almost two minutes.

Jan 1, 1993

By Edwin J. Connell, O&apos

Investment in mining and related process facilities will be more costly and complex in the 1980s than ever before. Interest rates and inflation are soaring; regulations are expanding; and in order to achieve economies of scale, plant facilities and mines are getting larger. As the pace quickens, the time/cost circuit closes around the resource owner or developer. Larger modern projects cost more money and take more time to build. The longer it takes to bring a project onstream, the more it costs in interest, escalation, and lost production. One solution to the time/cost squeeze is to take advantage of systems developed by major contractors serving the mining industry. These contractors have been serving clients in planning and executing large and small projects for many years. They have developed systems which, if applied at an early point in the project's life, can be a significant benefit in development of mineral resources. The systems involve performance of feasibility studies, economic evaluations, and the project installation itself. First the Feasibility Study Feasibility studies can minimize risk through systematic evaluations while progressing toward the ultimate objective-an operating plant. Normally, studies are initiated with a minimum amount of specific information and a maximum number of as¬sumptions. Through the course of the study program, assumptions are continuously confirmed, refined, or rejected by facts until a sound basis for decision is available. High on the list of cost effective tools for evaluation is the use of a geostatistically derived sampling program that provides a highly accurate ore reserve estimate for economic evaluation. When a predetermined sample of data from the drilling program and bench-scale or pilot-plant tests are received, a detailed feasibility study may be started. This study can involve design of the mine,

Jan 10, 1980

By A. Fiszer

One of the major problems with deep Polish hard coal mines are deformations of close-to-wall galleries since they are necessary and must he kept open for emergency situations and are largely responsible for work disturbances. In order to ensure safe and effective working operations, it is necessary to often rebuild galleries which, apart from the inevitable stoppage of operations, is greatly disadvantageous for the operation of a mine. The largest problems with maintaining the galleries open occur in Lower Silesian Coal Field mines where sometimes it is necessary to reconstruct the galleries several times [(Fig. 1)]. In light of what has been said above, the aim of this article is to present the reader with methods and ways of determining deformations occurring in close-to-wall galleries. Squeezing or convergence of headings is only a portion of the entire process of ground movement caused by ground disturbance due to workings. The term "squeezing of headings" is to be understood as a shortening of the distance between a point set on the roof of a heading and the corresponding one on the floor. It is very important to know the rules governing the process of squeezing in a particular mining system since it affords possibilities to define changes of the process and its parameters at any moment for a given system. This is of utmost importance because convergence of a heading is one of the most significant manifestations of ground pressure which has already been proved by studies performed by Everling (1). On the basis of those studies it has been observed that there exists an almost linear relation between the rate of convergence and loading [(Fig. 2)]. This, in turn, means that the deformations of the already exploited portion of heading are proportional to the pressure changes.

Jan 1, 1982

By Gary F. Rajala, Bruce R. Greenwood

INTRODUCTION The Empire Mine is an iron ore mining, concentrating and pelletizing facility operated by The Cleveland-Cliffs Iron Company in the Upper Peninsula of Michigan. Owners of the mine are Inland Steel, LTV Steel, Wheeling-Pittsburgh Steel and Cleveland-Cliff s. The orebody is a fine-grained, low grade iron formation with magnetite as the primary constituent. Also present are iron carbonates, iron silicates, chert, hematite, goethite and quartz. The original six concentrating lines were started in late 1963. Successive expansions of ten lines in 1967, five lines in 1974 and 3 lines in 1979 have resulted in Empire reaching a present annual capacity of 8.0 million long tons of pellets. The Empire flowsheet was developed over several years of laboratory bench testing, pilot plant testing and testing of a full-scale primary autogenous grinding circuit. Since the original flowsheet was established, modifications have been made based on pilot plant and full-scale plant tests. The present flowsheet for three sections of the concentrator consists of one stage of crushing, two stages of closed circuit autogenous grinding, two stages of magnetic separation, one stage of hydraulic concentration and two stages of flotation (rougher and scavenger). The flowsheet for the fourth section of the concentrator (Empire 4) is the same as the first three sections, except a crusher has been added to crush excess pebbles. The Empire 4 flowsheet appears in the at- tached figure. PRIMARY GRINDING CIRCUIT FLOWSHEET Empire has a total of 24 individual grinding lines. However, at the present time, Line 1 is not being used for processing crude ore. The primary mill on Line 1 is now grinding flux stone for fluxed pellet production and the secondary mill is being used as a ball mill to grind rougher flotation tailings prior to a scavenger flotation circuit.

Jan 1, 1992

By Eugene A. Lang, William R. Archibald

Early in 1972, Rocky Mountain Energy Company approached MARCONAFLO with a unique request for assistance. They controlled a series of scattered ore deposits in a remote section of Wyoming which had become increasingly valuable despite their relatively small size, great depth and low grade. At the time, MARCONAFLO was in the process of developing a tailings reclaim system which was based on the use of submersible capsules. It appeared that this basic concept might be adapted to slurry uranium ores and pump them to the surface through a bored hole. This presentation will review for you the development of this unique and potentially very important application of MARCONAFLO technology. This first slide (SLIDE 1) depicts the total mining concept envisioned by MARCONAFLO and Rocky Mountain Energy Company. A series of six self-contained mining units would be positioned through boreholes into the ore strata. An oscillating MARCONAJET would direct a high pressure jet stream into the orebody and put it into a slurry which would flow back to a slurry pump. The slurry would then be pumped to the surface and to a collection tank from which it would be transferred to processing. Both the MARCONAJET and the slurry pump would be actuated and controlled by means of a hydraulic power console mounted on the trailer behind the service tower. By means of a high pressure water pump also mounted on the trailer, return water from processing would be delivered to the MARCONAJET to slurry the ore. Tailings would be returned to a backfill unit for redepositing in the mined-out cavities. A drill rig would precede the mining, and it was estimated that this configuration would represent an optimum system for most effective equipment utilization.

Jan 1, 1976

By Giovanni Toniatti

Brazil is a country with continental dimensions. It hosts many different varieties of terranes and geological environments in its 8.5 million km2 (3.28 million sq miles). This mineral endowment has been important for the country's economic and social development process since the early colonial period, leaving Brazil with a legacy of almost 400 years of mining tradition. Mining in Brazil started in the early 17th century with diamond and gold discoveries. The made the country the leading producer of both for more than a century. This phase faded by the late 18th century when the alluvial deposits were depleted. It finally yielded to competing countries where technology and capital were being applied more efficiently. This period of mining dormancy lasted from the late 19th century until the first decades of the 20th century when Brazilian mining picked up. There was growing pressure on mineral resources by the affluence of the industrial society. The fast-growing demand resulting from the two world wars had brought the Brazilian mineral wealth back to the scene. This second Brazilian mineral boom made the country a leading producer of iron and manganese ore, quartz crystals and other strategic minerals. This expansion in Brazil's mining industry provided the basis for the country's industrialization process. This was led by the Brazilian steel and petroleum industries. Unfortunately, the thrust provided by this modern industrial basis was not properly used as a lever for further industrial development. The upstream industrialization process was not supported by the proper development of the raw materials supplying basis. The resulting industrial model was heavily dependent on imports of raw materials. It did not support the economic growth and faced fierce industrial competitiveness and sophistication that emerged with the postwar economic boom.

Jan 1, 1997

By Shinya Ono, Tsuyoshi Katoh, Yuusaku Tominaga

In order to monitor/control airflow rate distribution in a complicated ventilation network installed many regulators, an integrated system composed of expert system, exerting programs for simulation to get macroscopic characteristics and drawing diagram, monitoring system and so on is introduced in this study. This system is made up of airflow velocity sensors and computers linked to an local area network. The main results of this study are as follows; 1) Combinations of two branches to monitor aerodynamic resistance change in a branch p in a network can be selected by comparing factor's value in a branch relation table. 2) When the combination of sensor branches for a branch p does not exist in the network at present condition, the system changes aero- dynamic resistances of appropriate branch q placed a regulator by referring branch relation table. And then the system asks other computer to get macroscopic characteristics under altered value of aerodynamic resistance of the branch q. 3) Dot pattern diagram shows airflow rate relation between an active branch and a passive branch. Three relations such as a) a straight line, b) a monotonous curve and c) extremums are displayed in different patterns for all the sets between an active branch and a passive branch at a time. 4) The ranges of airflow rate in coal faces by changing aerodynamic resistance of any one branch placed a regulator are shown in the Pareto diagram using values in the branch relation table. 5) Ventilation transfer diagram with two parameter, one shows airflow rate in a coal face and the other shows energy provided by main fans to overcome aerodynamic resistance in a net- work, is utilized to decide countermeasures for decreasing energy consumption in the network on increasing of airflow rate in the specified branch.

Jan 1, 1995