Search Documents

By George Aul, Richard Ray

Short-hole horizontal degasification systems have been utilized in Island Creek's Virginia Division mines since 1986. These systems remove methane from the coal seam in advance of longwall mining. Without an in-seam methane drainage program, methane liberation rates from the longwall faces may exceed 0.47 cu m/s (1,000 cfrn), requiring 47 cu m/s (100,000 cfm) of air for adequate dilution capability. Optimization of the degas systems has enabled methane liberation levels and the associated ventilation requirements on the longwall faces to be reduced by 50 to 80 percent. Since the inception of the first degas system at the Virginia Pocahontas No. 6 Mine, Island Creek has developed an overall methane drainage program designed to maximize gas production and minimize ventilation requirements for methane dilution. Gas production from the degas systems is affected by four main design criteria: (1) hole location, (2) hole length and spacing, (3) collection system capacity, and (4) time available for drainage. Drilling equipment and materials for the gas collection system are selected to meet the necessary criteria while minimizing manpower requirements. Benefits gained from reducing methane liberation rates from the longwall faces are fourfold: (1) improved safety due to lower methane concentrations in the face area, (2) fewer production delays caused by excessive methane concentrations, (3) lower fan operating costs resulting from reduced air requirements, and (4) enhanced worker comfort resulting from lower air velocities and less dust generation.

Jan 1, 1991

By V. Scovazzo

Cost-effective underground mine configurations have been designed in highly fractured rock masses where the stone possesses a high material strength. A limestone mine in the eastern United States is used to demonstrate procedures for the geotechnical design of one such operation. The mine discussed is located in both limbs and the axis of a recumbent fold that fractured the rock mass. In a highly fractured rock mass, where the host rock has high strength, a design can be developed to alleviate intact rock failure. This is possible because in most cases as the stress levels needed for intact failures are approached, the stresses are quickly dissipated due to movement along discontinuities, which represent planes of weakness. As a result most underground failures in highly fractured rock are due to sliding or toppling. Even when intact rock fails in a highly fractured rock mass, it is the movement along an existing joint or other weakness plane that often initiates or causes this failure. It is therefore important to obtain the characteristics of weakness planes that are the discontinuities within the mass. The required information on weakness planes, geology, and strength of materials is discussed and recommendations for obtaining this information are presented. A discussion is provided on failure modes and the use of developed information for their evaluation. The impact on geotechnical design is demonstrated through pillar sizing procedures; however, this approach can also be applied to mine roof and pillar foundations.

Jan 1, 2004

By O. A. Bascur

An expert process operation advisor system can increase plant efficiency, even in a complex, natural environment where not all elements of the production process can be measured directly. This system, develaped and tested in a Frasch process sulphur mine, monitors key process variables with extended qualitative pattern processing and provides on-line advise to the operators of sulphur production wells. An expert system framework captured common sense rules generated from years of experience obtained in the operation of a sulphur well monitoring system. The existent operating procedures were enhanced by process analysis using a qualitative modeling approach which provided extended rules for on-line classification of a well operational status and an expert alarm system. The methodology for development and implementation of the process advisor is presented in this report. Qualitative process modeling, statistical process control and heuristics were incorpomted into the process advisor resulting in a more efficient use of heat, an extended well operational life and the resulting cost savings. The computer process advisor also allowed the operator to concentrate his attention on the weak wells or wells in trouble. A process management system improved plant operation by automatically storing well data into a commercial database for operator validation. The enhanced relational data base system provided valuable and timely information for planning and decision making. The synergistic combination of on-line process analysis tools, expert control systems and database technology is shown to facilitate the flow of materials, energy and infomation in a modern plant.

Jan 1, 1990

By A. Iordanidis

Mining activities have recently been taken place in Vourinos mountain, northern Greece, exploiting the so-called ?olivinite?. A representative sample was collected from this mining area. Mineralogical analysis was conducted using X-Ray powder Diffraction (XRD). A thin section was prepared and analyzed under optical microscope. X-Ray Fluorescence (XRF) was employed for the chemical analyses of major, mi-nor and trace elements. Environmental Scanning Electron Microscopy coupled with energy dispersive x-ray analysis system (ESEM-EDX) was also applied for the characterization of the sample. Forsterite (Mg-rich olivine) and enstatite (Mg-rich orthopyroxene) were the main mineral phases determined by XRD, with a 56% and 44% content respectively. Trace amounts of chromite spinels were also determined. Based on this characterization, the industrial rock proved to be a hartzburgite (a type of peridotite in petrological terms). Optical microscopy and ESEM-EDX provided similar observations and confirmed the above-mentioned results. XRF revealed a composition of 43.31 MgO, 44.25 SiO2, 9.98 Fe2O3, 1.40 CaO, 0.67 Al2O3, 0.22 MnO, 0.01 TiO2 and negligible amount of LOI (<0.1%). Trace elements with high concentrations were Cr (2678 ppm) and Ni (2044 ppm). The comprehensive characterization of this mining product suggested the suitability for various uses, such as refractories, foundry and slag conditioner. Additional experiments are being carried out for environmental applications, e.g. wastewater treatment.

Jan 1, 2006

By Betty L. Gibbs

A short course, held during the SME Annual Meeting in Phoenix, AZ in February, focused on software for surface and underground mine modeling. The objectives of the short course were to review techniques for surface and underground mine planning. Mine planning software vendors were invited to demonstrate how their software runs, given a standard data set. Six vendors of mining-specific software participated in the workshop. They were Exploration Computer Services (MINEX 3D), GEMCOM Services, Inc. (PC-MINE), KJRA Systems (VULCAN), Mine Development Associates (SURPAC), Micromine and MINEsoft (TECHBASE). Data set A data set was created to challenge the capabilities of each vendor&apos;s software. The criteria used for the data set selection were: • a minimum of 300 drill holes; • the data must include topography, drill hole survey, assay and formation contacts; • the deposit was multimetallic; and • there was the potential to be mined by surface and underground methods. The data set used was an actual, complex copper ore body with a small amount of gold. The ore body was close enough to the surface to be mined by surface techniques. Part of it, though, was also amenable to underground mining. To further complicate the problem, a river ran across the area of the ore body. This presented mine planners with the problem of either moving the river or mining around or below it. The ore body had not been mined, so no data was available for the tons and grade actually produced. Data for the mine planning problem was distributed to each vendor about two months before the short course. They had the opportunity to load the data into their systems, build an ore body model and perform preliminary work. During the first day of the workshop, the vendors received problems concerning the ore body. They went to work on their machines, attempting to show short course participants how their software could help solve the problem.

Jan 1, 1992

By Ted D. Johnson

INTRODUCTION The report of the workshop on Alternate Energy Strategies estimated that the world&apos;s reserve of uranium oxide is about 700,000 tonnes. In order to extract these reserves, it is estimated that between 100 and 200 million tonnes of solid waste and of the order of 1 billion cubic meters of liquid waste will be generated. In addition, radium within tailing will continue to generate radon gas as it decays for many years after closure. Hence, the handling, storage and possible use of uranium mine waste is a matter which deserves serious consideration and planning. Since the properties of the waste will largely dictate the method of handling and storage or use of the waste, the properties of the waste should be determined, to the degree possible, prior to the design and subsequent operation of the mine. Uranium mine waste has both solid and fluid constituents. The solids include soil and rock removed during site preparation, similar material removed during development of the mine and uranium tailing generated by the mill. Soils can be stockpiled for reuse during reclamation or used as earth materials for construction of fills, roads, dams and soil linings. Rock can be stockpiled, used as mine backfill or can be used for earth construction in fills, roads and dams. The tailing is usually placed in a tailing storage area. The fluid constituents are both liquid and gaseous. The liquid waste is generally composed of the mill water; however, additional waste water can be generated by dewatering processes and diversion of surface runoff. The gaseous constituent of the uranium mine waste is radon generated by the radioactive decay of radium in the ore tailing. DEFINITION OF PROPERTIES The following presents a brief definition of some of the more important properties discussed later. The definitions are not intended to be comprehensive, but are useful as a basis for understanding.

Jan 1, 1980

By William C. Cox, Ronald E. Heuer, Jean-Michel Loignon

The Gatineau shaft described in this paper was an excavation of about 38 m diameter and 21 m depth constructed in Gatineau, Quebec, across the Ottawa River just north of Ottawa, Ontario. A large sewage lift pumping station-was to be constructed in this excavation. Subcontractor for the shaft excavation and initial support was Beaver Underground Structures Ltd., of Dorval, Quebec. Mr. William C. Cox of Beaver conceived the idea for the support system used in this excavation, and was responsible for the construction activities. Initial analysis and design concepts for the lining system were developed by Mr. Ronald E. Heuer. Detailed lining design and construction monitoring were the responsibility of Mr. Jean-Michel Loignon. Geologic conditions indicated by two borings within the shaft area are illustrated in Fig. 1. The shaft excavation would be in the sensitive Leda silty clay. The clay is of stiff to very stiff consistency, with an insitu vane shear strength averaging about 115 KPa (2400 psf) and a reported low value of about 87 KPa (1820 psf). Low strength values were from the middle of the clay layer, with higher strengths at the top and bottom. Average shear strength at the level of the base of the excavation was about 137 KPa (2860 psf). Remolded vane shear strength averaged about 20 KPa (420 psf), with a reported low of 13 KPa (270 psf). Based upon average strength values, the clay sensitivity is 5.8. The clay has an average water content of 53% (range 43 to 66%), which is near its liquid limit (average 56%). The clay unit weight is about 1760 kg/m3 (110 pcf). Underlying the shaft site at shallow depth is limestone bedrock within which the piezometric head is approximately equal to the original ground surface elevation. For shaft support, a -cast-in-place concrete wafer system was considered, but was discarded because of time restrictions imposed by concrete placement and curing. The support system selected utilized liner plate with light steel walers closely spaced. The light rib

Jan 1, 1983

By Eivind Grøv

"INTRODUCTION Tunneling and underground excavation is related to handling of uncertainties, risks associated with geological conditions are significant and ‘unexpected geological conditions’ often claimed. This fact was brought to the table long ago, and ITA (the International Tunnelling and Underground Space Association) published its 25 Recommendations on Contractual Sharing of Risks in 1988 (Ref. 1). This public-cation constitutes an important asset to the tunneling industry in terms of being a guideline for those working with contractual issues, even today almost 30 years after being published. A more recent document is the ITIG code of practice for risk management of tunnel works from 2015 (Ref. 9). Various countries or geographical regions have their own view and tradition on risk sharing and tunnel contracts. In Scandinavia unit rates contracts are most commonly used with bid-build model, it shares risk between owner and contractor, owner retains the risk for geological conditions while contractor carries risk for performance efficiency. Rock strengthening is determined assessing rock mass quality encountered at tunnel face. Grouting is applied to stem water. Actual quantities may differ from the contract’s BoQ but a flexible contract with remuneration is installed to enable adjustment of actual quantities. Variations of quantities involve a clause to adjust construction time. Unit price contracts deals with expected and foreseen still ‘unexpected geological conditions’, if the ‘unexpected’ element results in variations in quantities. Work activities have quantities and ‘standard capacities’ for regulation of construction time. Variations in quantities are expected in tunnelling and hardly deserve the term ‘unexpected’. If truly unforeseen geological features necessitate work not included in the BoQ, then the contract must be supplemented and can be said to be inappropriate. Fixed price contracts may not provide the intended predictable cost and is as such also inappropriate in the view of a risk sharing principle, once the geological baseline proves to be incorrect. ‘Adjustable fixed price’ contracts, combining unit rate and fixed price, may prove suitable."

Jan 1, 2016

By A. Gupta, S. C. Srivastava, K. K. Saroj

Bacterial degasification of methane and conventional methane drainage for generation of power have become accepted practice. Comparative economies of both the techniques have been described. Authors have discussed an alternative technique, involving complete methane biocycle. The first stage of the entire process involves gasification of coal using a consortia of bacteria to generate methane. The generated methane has been proposed to be pumped,as in conventional methane drainage. Technique described is basically similar to underground coal gasification, with the difference that in place of coal combustion, degradation of coal to lower molecular weight compounds by one set of bacteria and then methanogenesis by methanogens, producing methane have been described. Brief account of communities of bacteria that may be employed have been dealt with. Three arguments in favour of proposed technology as an alternative to conventional coal mining are: 1.Total elimination of hazardous operation. 2.Availability of power plants based on methane drainage, assuring comparative economies. 3.Possibility of utilisation of fuel cell technology for power generation giving higher efficiency. All the three phases of complete blocycle viz (1) methane generation from coal (ii) conversion of methane to hydrogen and oxygen (iii) conversion of products so obtained to methane, thereby completing the cycle have been discussed. INTRODUCTION Drainage of methane by conventional pumping process (Boxho,et.al.,1980) not only is helpful in maintaining safe extraction of coal, but with utilisation of extracted gas for power generation, also helps in over all economy of coal mining. This is gradually becoming standard practice for mining of coal in highly gassy mines. An alternative technique (Thakur et. al., 1991) of bacterial degasification of coal seams is also gradually gaining ground. The bye products of this process that is carbondioxide and water, do not contribute towards economy of coal extraction process. However the technique has its own advantage particularly in goaf area for avoiding fire hazard and drainage of methane from coal seams prior to initiation of mining operation. Either of these techniques could be applied in specific situations with success.

Jan 1, 1993

By Huayang Luo, Hui Li, Wei Zhou, Gang Chen, Scott Huang

Abundant beach and offshore resources of gold deposits are demonstrated along the coast of Alaska, and Nome is one of the richest places. Considerable amounts of mineral resources data were collected and stored in geodatabase of ArcGIS. In searching for the best model for the interpretation of the Nome offshore gold placer deposit and accurate estimation of the reserve, the data were processed and visualized using ArcGIS. The gold concentration data collected from the Nome offshore deposit are of characteristics such that: (1) near lognormal distribution of data, (2) high positive skewed distribution, (3) a small number of extreme values dominating the reserve estimation, and (4) apparent anisotropy of the variogram. These characteristics make the development of an interpolation model for the gold deposit a challenging task. In this study, it is determined that five geostatistical methods provided by ArcGIS with visualization capability, i.e., Inverse Distance Weighted (IDW), Ordinary Kriging (OK), Ordinary Kriging with lognormal transformation (OK-log), Simple Kriging (SK) and Indicator Kriging (IK) are suitable candidates for the development of an interpolation model. The five algorithms are evaluated and compared with each other in the study. Cross-validation technique is employed to examine the accuracy of the five approaches. It is determined that the OK and SK algorithms are not suitable for this dataset because of the difficulty of fitting the semivariogram model despite their lower RMSE (Root-mean-square error) and the higher RMSS (Root-mean-square Standardized). The OK-log algorithm does not provide satisfactory prediction either, because it places too much weight on the role of extreme values resulting in overestimation and extremely high RMSE. Reserve estimation of each blocks is conducted using each of the interpolation methods and compared with the reserve calculated using the conventional polygon method. The IWD and IK algorithm seem to provide estimations more agreeable with the conventional polygon method.

Jan 1, 2005

By Donald A. Dahlstrom

INTRODUCTION Solid-liquid separation is an important and many times a critical step (or steps) in a mineral or coal processing plant. Some examples of typical critical separations are as follows: 1. Operating a seven to eight stage CCD thickening circuit to re¬cover almost all of the caustic and alumina trihydrate values in an alumina plant. This must be accomplished with highly scaling slurries, starting temperatures of over 100°C and operate on a closed circuit system. 2. Making a filter step operate to produce a proper moisture for the balling step so that the pellet furnace can produce a proper product. Bentonite addition must be minimized and a good quality filtrate must be maintained to prevent abrasion of the internal parts of the filter. 3. Operating a closed water system in a coal washing plant so that reclaimed water containing less than one percent suspended solids is produced for reuse to maintain beneficiation ef¬ficiency. Refuse solids must also be thickened so that they can be effectively dewatered to meet state disposal requirements. 4. Recovering phosphoric acid values from a slurry containing gypsum and other gangue solids at an elevated temperature. This must be done while minimizing wash water and maximizing P2O5 re¬covery while simultaneously minimizing scale problems. While solid-liquid separations are important to overall performance in the processing plant flowsheet, it is also a significant factor in plant costs. Capital and operating costs for all the solid-liquid separation steps (includ¬ing water reclamation for reuse) in such plants are probably between 10 and 20%. Energy consumption can also be important in these separations. For example, in the copper concentrator, it is the third largest category in energy consumption, after comminution and flotation. Obviously, solid-liquid separation steps in a plant demand proper atten¬tion in design in order to achieve both optimum performance and cost. Simultaneously, knowledge of funda¬mentals are important to improve results in existing plants.

Jan 1, 1986

By R. O. Burt

Gravity concentration - the separation of minerals according to their relative density - is one of the oldest forms of mineral processing. Even though modern technology has developed a range of other processes, gravity concentration remains as one of the most important methods employed for mineral separation. The range of minerals recovered covers a wide spectrum, from andelusite to zircon, from coal to diamond, from gold to industrial mineral. The long history of gravity concen¬tration, along with a still imperfect understanding of the various mechanisms involved has resulted in a series of ingenious engineers developing, some¬times perfecting and sometimes rejecting, a wide range of equipment, suited for a variety of different duties. &apos;Selection&apos; in the context of gravity separation, is primarily the choice of the right type of equipment for the separation in hand; &apos;sizing&apos; of the correctly chosen unit is, more often than not, determining the appropriate number of units required to suit the throughput. The accent of this chapter will, therefore be &apos;selection&apos;. A brief description of the major types of gravity concentration equipment will follow a discussion of the factors which determine the selection of the correct unit. CLASSIFICATION OF GRAVITY CONCENTRATION EQUIPMENT All concentration equipment has a primary function and a secondary function. The primary function is the efficient separation of the constituent minerals into two or more discrete phases; the secondary function is to effectively cause the discharge of these discrete phases into separate compartments (Aplan 1975). For maximum efficiency of operation, the forces which effect the primary function should not also result in the secondary function occurring; in such cases optimum operating conditions required for the primary function, separation, may have to be compromised to ensure reasonably efficient operation of the secondary function, product discharge. With gravity concentration, the primary function is effected by the relative movement of minerals of different density in response to gravity and one or more other forces, the latter often including the

Jan 1, 1986

By Clinton Strachan, Dirk J. A. van Zyl

11.1 INTRODUCTION This chapter outlines some of the selection and design considerations for leach pads and liners. Leach pads and liners are generally chosen to provide the required or desired levels of low permeability and foundation conditions at minimum cost. The selection and design of a particular liner depends upon its anticipated use and performance, and what materials may be available. A leach pad is the firm base for a heap. When geomembrane liners are used, the pad is the firm, compacted foundation upon which the liner is placed. In the case of a clay liner, the clay liner is usually also the pad. It is important to consider the design of a pad or liner in terms of a system. The "leach pad system" consists of the prepared foundation, bedding layer (if used), liner (s), seepage collection or detection layer (if used), and cover layer. Foundation preparation is necessary to ensure a stable base for the rest of the leach pad system. A bedding layer is used to protect a liner from being punctured by large angular fragments in the foundation material. A seepage collection or detection layer, consisting of well-drained material and (sometimes) pipes draining to a collection sump, is included when a double liner is used. A cover layer on top of the liner can serve the following purposes (van Zyl and Strachan, 1986): • Preventing of ultraviolet light exposure to sensitive geomembranes; • Limiting evaporation from compacted clay liners and thereby eliminating cracking of such liners; • More efficient collecting of leachate; and • Protecting the liner from damage during heap construction. Economic evaluations of alternative liners for a project must include the overall system. For example, a geomembrane liner may require different foundation preparation and cover material selection and placement than a clay liner. Liners can be made of compacted clay onsite, amended soil, or geomembranes. Geomembrane is a generic term that has been proposed to replace many terms, including synthetic membranes, polymeric membranes, plastic

Jan 1, 1988

By Hassan El-Shall, G. L. Zucker, T. S. Jordan

INTRODUCTION This chapter will discuss, both from fundamental and practical points of view, the flotation of non-sulfide min- eral s. The flotation characteristics of silicates, salt-type minerals, oxides and coal will be reviewed. Dup- lication of the thorough and excellent presentations by many authors is not intended and a comprehensive list of references is included. GENERAL PRINCIPLES Collectors for Non-Sulfide Minerals : All minerals, with only a few exceptions are readily wetted by water, that is, they are said to be hydrophilic. The purpose of a collector is to coat the mineral surface and render it hydrophobic, preferring an environment of air over an environment of water. Relative to sulphide minerals, the non- sulfides are more naturally hydrophilic and therefore, require a collector with a greater chain length. This is accomplished by using a collector which has a proportionally longer hydrocarbon chain. Both anionic and cationic flotation collectors are used in non- sulfide flotation. Anionic Collectors. These are collectors which ionize in solution to give a negatively charged radical. They have the general structure R-A, where R is a hydrocarbon having 8 or more carbon atoms and A is a hydrogen or an alkali metal. The most common collectors in this group are fatty acids which could have saturated or unsaturated hydrocarbon chains. Such chains may be straight or branched. The configuration of the chains affects their solubility in water and their adsorption characteristics. In general, as the chain length increases the adsorption and the collecting power increases. However, it should be noted that the solubility decreases. The solubility of unsaturated chains is greater than that of saturated fatty acids because double or triple bonds are polar and thus attract water molecules. Solubility data for collector metal salts, even though important for a proper understanding of flotation are not available for all collector systems. Solubilities and structures of different fatty acids are reported by Fuerstenau (1982). Values for the solubility products of fatty acid salts selected from a paper by Du Rietz (1958) are given in Table 1.

Jan 1, 1986

By William E. Foreman

Editor&apos;s Note: For purposes of uniformity throughout this book, Coal Preparation, 5th Edition, the editors have advocated the use of the U.S.A. Sieve Series of testing sieves (see Table 6-2) as the testing sieves of modem choice. The adoption and use of the U.S.A. Sieve Series and its forerunner, the Tyler Standard Screen Scale, has for over seventy-five years introduced uniformity into reports; has simplified the comparison of results; and has provided control for operation of modem coal preparation circuits. While a full explanation of the differences, and more importantly the similarities of these two measuring systems cannot be stated here, it is felt that a brief clarification of terms is in order. The difference between the U.S.A. Sieve Series and the Tyler Standard Screen Scale Sieve Series is the identification method. Tyler Screen Scale sieves are identified by mesh designation with the width of opening varying by the square root of two, or 1.414 times the width of opening in the previous sieve. The U.S.A. Sieves are identified by openings in millimeters or microns and also arbitrary numbers which do not necessarily mean the mesh count; this series uses width of opening variations in the order of approximately the ratio of the fourth root of two, or 1.189. Tyler Standard Screen Scale and U.S.A. Sieves can be used interchangeably, and to avoid confusion the nameplate of all Tyler Screen Scale sieves show the U.S.A. Number, while all U.S.A. Sieves show Tyler Screen Scale mesh equivalent numbers on the nameplate. INTRODUCTION Sizing is the process of separating mixed mineral particles into groups of particles all of the same size, or into groups in which all particles range between definite maximum and minimum sizes. This chapter applies the modem mechanical screen and the liquid-solid cyclone (hydrocyclone) to the process of sizing solid particles as applied to coal preparation. Screening is a mechanical process that separates particles by size. Modem coal preparation is made possible by efficient sizing. Sizing of coal is defined in terms of the opening through which an individual particle will or will not pass, or as two openings, the larger of which passes the particle and the smaller of which retains the particle. Screening accomplishes sizing by passing coal of a wide range of sizes through a series of screens, each of a decreasing size. The individual screen discharges are then directed into different screen products for subsequent sale or processing. Screening in modem preparation plants is done for the following reasons: 1. Removal of fine coal before a size reduction step. 2. Size separation of the coal into a coarse and fine fraction for sized products or for processing in coarse and fine coal circuits. 3. Recovery of heavy media from heavy media coal cleaning circuits.

Jan 1, 1991

By R. Timothy McCrum

It is not often that the Interior Department&apos;s Bureau of Land Management, Office of the Solicitor, and Interior Board of Land Appeals (IBLA) jointly act to do the mining industry a good turn. That happened, however, in the recent decision, Schlosser v. Pierce, 92 IBLA 109 (1986). It was ruled that the theorized "independent mine requirement" was not a part of the discovery standard for mining claim validity under the 1872 Mining Law. The phrase "independent mine requirement" would require the mineral reserves within the boundaries of each individual mining claim in a claim group to support an independent economic mining operation. This, without regard to the fact that reserves on adjacent claims could be mined in a group operation, resulting in greatly reduced mining and marketing costs per ton of ore. Such a rule would render invalid under the 1872 Mining Law mining claims for almost all low-grade, high-tonnage, commercially valuable mineral deposits. Until the Schlosser case, no judicial or administrative decision had addressed the issue of the independent mine requirement. Nonetheless, a series of Interior decisions in the 1970s implied such a rule. Even the Rocky Mountain Mineral Law Foundation reluctantly concluded in 1984 that, "each claim to be valid must be capable of being operated at a profit independently of any other claim," the Foundation did criticize the rule as "excessively stringent" and urged the adoption of a "more realistic rule." Fortunately, the IBLA did just that in Schlosser when it ruled that the "application of a requirement that each claim be independently capable of being mined and marketed at a profit is rejected," 92 IBLA at 134. Now, a year after the 1986 decision, there remains some unwarranted confusion over the issue resolved in, and the meaning of, the Schlosser decision. There is no need for this confusion. The Interior Department&apos;s decision is a clear and legally sound victory for the mining industry. Grazing rights vs. mining claims The Schlosser case was an unusual mining claim contest. A private contest was brought before the Interior Department. Schlosser was a federal grazing lessee and surface owner. He filed against Pierce, the locator of a group of mining claims for bentonite over the same lands. At a hearing before interior&apos;s administrative law judge (alj), Schlosser&apos;s counsel began laying the foundation for the independent mine requirement. Counsel asked the mining claimant&apos;s expert whether he would go through the permitting procedure, road building, and reclamation just to mine the amount of bentonite on any one claim in the group. Schlosser&apos;s counsel proceeded with this line of questioning for each of the 16 claims in the group. Pierce&apos;s mining expert testified that the tonnages of mineral on any individual claim could not be mined, processed, and marketed at a profit if only one individual claim was considered. However, if the claims in the group were operated jointly, all the mineral could be mined, processed, and marketed at a profit.

Jan 8, 1987

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

The STG integrated method of grouting can be divided into the several phases as outlined in preceding chapters. For convenience in describing technical procedures, they can be grouped as: 1. Investigations in non-geotechnical, exploration bore¬holes. 2. Drilling the holes necessary for geotechnical investiga¬tions and for grouting. 3. Conducting appropriate hydrogeologic tests in those holes and consequent calculations. 4. The preparation of a clay mortar. 5. The preparation of a clay-cement grout with additives. 6. The injection of the grout. 7. Checking the quality of the grout curtain. Items 2, 4, 5 and 6 are discussed below. These activities contain the procedural aspects of grouting. 7.1 DRILLING GROUT HOLES Grout holes belong to a very select class of drillholes. The necessary drilling equipment must enable the operator to drill the holes in inclined, twisting directions. In addi¬tion, the equipment must permit drilling under structurally and hydrogeologically complex conditions. The equipment must permit the operator to conduct specific testing activi¬ties in the drillholes. These activities include hydrodynamic analyses, flowmetric analysis, and the installation and re¬moval of deflectors, packers, grouting plugs, casings, lin¬ers, pumping facilities and other work. As explained in Chapters 5 and 6, the grouting of sat¬urated rock is conducted both through holes drilled from the surface and through holes drilled from the face of a shaft, drift, or tunnel. The drilling of grout holes from the surface can be carried out by an aggregate of equipment that can be the same equipment used for drilling exploration boreholes. Depending on the projected depth of the holes, the STG ZIF- 1200MR and ZIF-650 drilling rigs (or modifications of them) are used. The SKB-4, SKB-5 and SKB-7 high-output drilling rigs (workover rigs) have been used in recent years. The STG BMP-24 drilling rigs are used for carrying out the descent-lifting operations for drilling holes from the sur¬face. In a number of cases, the UKB-500C, URB-3AM and URB-2A power-fed drilling equipment is used for drilling holes from the surface. It should be noted that the drilling of grout holes usually requires an electric drive assembly. Drilling with diesel drive assemblies would be used only to preclude the possi¬bility of losing electric power during drilling operations. Turbine drilling would be used only for appropriate techni¬cal-economic reasons. The selection of the grout hole design is determined by the hydrogeological and structural geological conditions at the site as interpreted in Chapters 2 and 3. The design of grout holes must be as simple as possible in order to min¬imize costs. Hole design guidelines can be adopted as a basis for this purpose, unless site-specific conditions require otherwise. The mouth of the drillhole must be outfitted with a guide-pipe having a length of at least 2 m and an outside diameter from 219 to 234 mm. The upper part of the hole must be attached by a jig consisting of borehole casing that has a diameter ranging from 108 to 146 mm. The length of the jig h is determined by the equation [ ] where k = 1.1 to 1.2 is the load factor; P,, is the injection pressure of the grout into the mouth of the drillhole; D is the external diameter of the jig pipe; m = 0.6 to 0.7 is the work condition factor; T[ ].1 MPa is the bonding value of the rock cemented to the jig. The grout hole is drilled from the jig shoe to the de¬signed depth using a rock-crushing bit with a diameter of 93 mm or more. However in complex hydrogeological condi¬tions when the shaft intersects unstable rock, other hole designs can be used. The diameter of grout holes must permit an aggregate of investigations to be conducted in them using down-hole borehole geophysical and flowmetric logging instruments. It is necessary to cement the casing strings reliably in the grout holes, thereby permitting the injection of the grout under high pressure through the pres¬sure tight mouth of the borehole. Technological details for drilling grout holes such as the rotational rate of the drill bit, the axial load on the rock¬crushing bit, and the drilling fluid flow rate are optimized for the specific rock-hydrogeological conditions largely by experience. The hole diameter and type of rock crushing bit are important variables in these details of drilling. It is advisable to drill holes using water as the drilling fluid. However in those cases where the hole walls are unstable or under very high ground water pressure, the use of a well¬ engineered drilling mud should not be precluded. Unfortu¬nately, drilling mud can influence test results. When steeply dipping fractures with inclination angles of more than 60 to 70° are encountered, it is necessary to drill guided, inclined grout holes. This procedure permits the maximum number of fractures in each hole to be stu-

Jan 1, 1993

By Joseph Rosta

The gold and silver review did not arrive in time for publication in the May issue. Gold The gold market generally was listless in 1992, although investors returned to the metal in the fourth quarter. The gold price declined for the second year in a row, averaging $11.05/g ($343.76/ oz), 5.2% lower than the $11.65/g ($362.44/oz) seen in 1991. The average price has declined more than 23% since 1987, when gold averaged $14.36/g

Jan 1, 1993

By John W. Robertson, Edwin A. Zink, Gerald P. Zink, John E. Wolgamott

Equipment which will reliably produce high velocity water jets for use in rock excavation is now available. This report reviews some cases where water jets were used in excavating low to medium strength sandstone in Colorado and Utah. The primary discussion is of water jet assisted rotary drilling for blast and bolt holes in tunnels, shafts, and chambers. The subjects include drilling performance, effects on work environment, safety, and controlled blasting results. Information is also presented concerning trench excavation utilizing water jets.

Jan 1, 1983

By M. Mohammed, S. J. Jung

The prime criteria in the design of underground openings with complicated geological structures is ground control. Stability of underground openings for deep mines is critical because incorrect orientation or geometry of the shaft, stopes and accessways often results in the failure of openings due to high stress conditions. Current design procedures for complicated orientation and geometry of mines are rapidly becoming inadequate. In this study, the finite element method (ANSYS) has been used with optimization criteria to design safer, more stable underground openings.

Jan 1, 1995