Search Documents

By H. L. Ford

Flocculant testing should be initiated for economic or performance reasons. When the decision has been made to test, the laboratory can provide valuable information concerning the various products under consideration. Properly conducted laboratory tests can determine: 1. If two flocculants are needed to achieve clarity or density. 2. Ease of mixing. 3. How quickly the material goes into solution. 4. Stability of prepared f locculant solution. 5. Stability of the floc formed. 6. Amount of mixing required for proper floe formation. 7. Optimum flocculant concentration. 8. Optimum pulp density. 9. Approximate location of the point of addition. 10. Single or multiple addition points. When a flocculant shows promise in the laboratory, a plant test should be scheduled. During the plant trial, arrange for normal conditions and start testing with a crew that is most familiar with the unit operation where the flocculant will be applied.

Jan 1, 1986

By Alan A. Campoli, Michael D. Zuber, Frank E. McCall, Gerald L. Finfinger

Injecting water under pressure to wet the coalbed in advance of mining reduces mining-generated respirable dust. Owing to economic and geological barriers, water infusion for longwall dust control in the United States is currently limited to the Pocahontas No. 3 Coalbed in Virginia. Water is pumped into the coalbed through underground boreholes drilled horizontally from the headgate toward the tailgate side of retreat longwall panels. This paper theorizes that the barriers to widespread utilization of water infusion for longwall dust control could be overcome by long-duration, low-pressure water infusion through vertical gob gas boreholes. Currently, 43% of the 72 longwall mines in the United States employ vertical gob gas boreholes. Computer coalbed reservoir simulation suggests that one vertical surface borehole could infuse the same longwall panel area as four horizontal boreholes in the current water infusion system for longwall dust control in the Pocahontas No. 3 Coalbed.

Jan 1, 1995

By G. L. Finfinger, F. E. McCall, A. A. Campoli, M. D. Zuber

Injecting pressurized water into a coalbed prior to mining reduces mining-generated respirable dust. Because of economic and geological barriers, water infusion for longwall dust control in the United States is now limited to the Pocahontas No. 3 Coalbed in Virginia. Water is pumped into the coalbed through underground boreholes that are drilled horizontally from the headgate toward the tailgate side of retreat longwall panels. This paper theorizes that the barriers to widespread utilization of water infusion for longwall dust control could be overcome by long-duration, low-pressure water infusion through vertical gob-gas boreholes. Currently, 43% of the 72 longwall mines in the United States employ vertical gob-gas boreholes. Computer coalbed-reservoir simulation suggests that one vertical surface borehole could infuse the same longwall panel area as four horizontal boreholes in the current water-infusion system for longwall dust control in the Pocahontas No. 3 Coalbed.

Jan 1, 1997

By Kai Nielsen

In underground mining coarse muck and large boulders lead to ineffective utilization of costly mining equipment, and extra expenses and delays caused by secondary blasting. Cost analysis in some Norwegian mines shows that these extra expenses may amount to 10% or more of total mine operating costs. A computer model has been developed for sensitivity analysis of underground longhole stope blasting. The basic idea of the model is : When increasing the blasting energy input and fragmentation costs, the fragmentation will be better. This will lead to cost savings for loading, hauling, secondary blasting and primary crushing. The blasting design giving the lowest overall costs will indicate the optimal practice. The model has been used with data from several underground operations in Norway. An example run with typical costs shows that the costs for drilling, blasting and secondary blasting are the most significant parameters in the optimization process.

Jan 1, 1986

By E. Topuz, M. J. McPherson, J. Banik

This paper summarizes the analyses of ventilation layouts for mines that experience both spontaneous combustion. The major focus is placed on the longwall coal mine layouts used in several countries. Each of the different layouts is modeled in the form of a ventilation network. The gob of a longwall panel is the most critical location for the occurrence of spontaneous combustion. Airflow leakage paths inside the gob are simulated by using a simplified grid-like network. Computer simulations with this model indicates that the W-system of ventilation is most effective in minimizing air leakage into the gob. Homer, the U-system of ventilation, with pressure balancing behind the face support line, is also found promising for longwall panels. The magnitude of air leakage into the gob is observed to change with the advance or retreat of bee, thus requiring appropriate balancing of pressure to maintain the leakage at a minimum.

Jan 1, 1995

By W. R. Dearman, N. Turk

A seismic fissuration index (K) is defined as the ratio of the difference in the P and S wave velocities obtained when a dry rock specimen is tested both under a load equal to half the uniaxial compressive strength of the rock (Vo) and without an applied load (Vd) to the velocity obtained without an applied load (Vd), as K = (Vo - Vd)/Vd. A similar seismic fissuration index is also proposed for classifying the dry rock mass in terms of field seismic velocities. The field equation is extended by including the intact rock seismic velocities. K is found to be related to the porosity of rocks. The proposed equation can equally be used for characterizing saturated rocks, using S-wave velocities. However, the time average equation should be used for characterizing saturated rocks, using P-wave velocities, even though this equation gives upperbound estimates of the rock material and fracture porosities.

Jan 1, 1986

By Roshan B. Bhappu

In situ mining and extraction is one of the Frontier Technologies that is destined to play an increasingly important role in the recovery of metals and minerals in the future. This premise is based on increasing costs of labor and energy, increasing awareness of environmental considerations and decreasing ore grades in the United States. Up to now, in situ mining has been successfully applied to a few favorable situations for the extraction of some evaporites, copper and uranium. However, because of its unique technical, environmental and economic advantages, this versa tile technology will find broader applications for the recovery of above commodities as well as for others which are currently extracted by hydrometallurgical means. This paper traces the development of in situ mining and extraction; stresses its dependence on interdisciplinary science and engineering; discusses its theoretical, practical and economic aspects; and finally presents potential applications of this Frontier Technology.

Jan 1, 1985

By Kenneth Maser, Douglas W. Ounanian, Joseph S. Boyce

Foster-Miller Associates, Inc. (FMA), under contract to the Department of Transportation (DOT) and the Urban Mass Transit Administration (UMTA), is currently developing an Extruded Tunnel Lining System (ETLS). The ETLS would reduce ground support costs in machine bored tunneling by eliminating the need for temporary support, and by slip-forming the final concrete lining directly behind the Tunnel Boring Machine (TBM). The system can advance at variable rates, from 0.6 to 3.7 m (2 to 12 ft) per hr, by combining three systems: a very high early strength concrete, continuously produced and delivered by a concrete process system; a slipform/bulkhead system for supporting the concrete prior to strength gain and exposure; and a control system for form/bulkhead alignment and concrete process control. Large-scale tests are planned to demonstrate the system in a 3 m (10-ft) diameter steel "tunnel".

Jan 1, 1981

By J. A. Herbst, Z. Rogovin, Lo. Y. C., K. Rajamani

Knowledge of the amount of time material spends in a continuous mill in a closed grinding circuit is essential for circuit performance analysis and scale-up design. A convenient method for acquiring this information involves the use of pulse tracers in residence time distribution (RTD) experiments. In typical grinding circuit experiments, RTD measurements are done by injecting a pulse tracer into the mill inlet and detecting it in the circuit exit. In this article, an easy mathematical method for calculating mean residence time and the degree of mixing of material in a mill present in a closed grinding circuit is developed. There are no restrictions on the location of the tracer injection or detection points with this method. Any convenient location in the circuit can be chosen without affecting the residence time distribution measured. The analysis of impulse response data obtained from several commercial grinding circuits using this method is presented.

Jan 1, 1988

By Scott G. Britton

In the real world of coal mining, the bottom line for almost every support project decision is economic (i.e., what is it going to cost?). Up to this point, I have discussed the methods to improve the performance of typical support projects by better installation, materials, and techniques, thus lowering the impact of the bottom line cost. In this chapter, 1 shall explore what costs are relevant in mining construction, and how these costs are developed. The chapter centers around two major discussions: (I) developing cost accounting techniques, and (2) cost-estimating procedures for support construction. Each focuses on the fundamentals of practical cost considerations necessary for decisions on construction projects underground. Since cost accounting, economics, and investment planning are all subjects which warrant complete discussions on their own, this chapter will focus on distilling the important concepts required by a planning engineer into an easily understandable presentation.

Jan 1, 1983

By B. K. Mishra, R. K. Rajamani

Discrete element is a numerical technique for describing the collision dynamics and motion of an assembly of particles. In particular, calculations are done on full three-dimensional space with a force-contact law for collisions and Newton’s law for subsequent motion. It may be said that there is no empiricism in this approach. The paper describes the full scale simulation of large diameter semiautogenous grinding mill of size 40X24 ft. It is shown that the simulation predicts the power draft of plant size mill extremely accurately. Also these simulations have been adapted uniquely to assess the motion of pebbles and slurry in pulp lifters. The passage of slurry from pulp lifters into trunnion is extremely important since flow-back and carryover must be avoided at all cost. The dynamics of slurry flow through pulp lifters is also described in this paper.

Jan 1, 2003

By Mark R. Rybak, James Delmonte, Travis Hartman

The City of Phoenix, Arizona designed a 7.2 km (4.5 mi) long water transmission main from the South Mountain Reservoir to the Ahwatukee Foothills Reservoir to address the growing demand for drinking water in the southeast valley. The pipeline design called for a bored tunnel in a very environmentally sensitive area. The Reach3B contract included an 2.44 m (8 ft) diameter TBM excavated tunnel, 1,847 m(6,060 ft) in length. The geotechnical investigation revealed that the tunnel would likely pass through zones of loose to moderately cemented soils (caliche). The primary tunnel support would consist of rock bolts, circular steel ribs, hard wood lagging, and mine straps. A TBM that could handle the ground conditions and allow for efficient ground support installation was required. This paper describes the construction of a small diameter rock tunnel in challenging ground conditions.

Jan 1, 2003

By M. Churchill, V. R. Degner

Over the past two decades, declining ore body grades and increased operating and construction costs have provided an incentive for the development of progressively larger flotation machines. As a result, the 1.7-2.8 m3 (60-100 cu ft) flotation machine of the 1950's and 1960's is being rapidly replaced by large volume machines. The result has been improved flotation machine specific capacity (tph processed per sq ft of floor space); specific power (hp per tph processed); and process control simplicity. The recent development and satisfactory plant evaluation of the 28 m3 (1000 cu ft) flotation machine allows economic and operating advantages in high tonnage mill applications. Some principles of mechanically induced air flotation and the development of the large 28.3 m3 (1000 cu ft) flotation machine are reviewed here. Performance evaluation in beneficiating metalliferous ores-copper, zinc, and iron-is also given and recently completed plant results provided. Mining lower grade ore bodies results in the need to process increased tonnage in the concentrator. This greater tonnage requires more individual flotation machines, unless individual machine capacity, or cell volume, is increased. As the ore processing rate of the concentrator increases, the benefits of progressively larger individual cells in the flotation section become more significant. The accompanying figure illustrates the advantages of a larger flotation machine. In the figure, the number of machines in the rougher-scavenger section is related to the plant tonnage for three sizes of flotation machine: 8.5 m3 (300 cu ft), 14.2 m3 (500 cu ft), 28.3 m3 (1000 cu ft). The 28.3 m3 (1000 cu ft) flotation machine results in 95 fewer machines, compared to the 8.5 m3 (300 cu ft) machine at 45.4 kt/d (50,000 stpd) feed. The flotation cell reduction is, of course, doubled at a plant production rate of 90.7 kt/d (100,000 stpd). Using fewer flotation machines saves floor space. The 14.2 m3 (500 cu ft) and the 28.3 m3 (1000 cu ft) machines result in a floor area reduction, relative to the 8.5 (300 cu ft) machine requirements, of 134.7 and 418.1 m2 (1450 and 4500 sq ft), respectively, for the 45.4 kt/d (50,000 stpd) rate and 269.4 and 836.1 m2 (2900 and 9000 sq ft), respectively, for the 90.7 kt/d (100,000 stpd) rate. In addition, flotation practice has shown that the "specific power intensity"-power per unit cell volume-is less for increased cell size. This results in a power draw reduction, for the rougher-scavenger circuit, of between 552 and 686 kW (740 and 920 hp) for the 14.2 and 28.3 m3 (500 and 1000 cu ft) machines, respectively, when processing 90.7 kt/d (100,000 stpd). Fewer cells improve machine control and simplify maintenance needs while reducing floor space and power requirements. These are tangible incentives for the development of large flotation machines for high tonnage applications. Flotation Principles The accompanying figure shows how key hydrodynamic regions influence the performance of a mechanically induced air flotation machine. Air is induced into the fluid from the top of the cell, due to the mechanical action of a rotating impeller. The impeller circulates the liquid, or pulp, from the bottom of the cell. The result of these dual flow paths is the mixing of the two fluids and one solid phase in the highly agitated region where physical contact between the air bubbles, and the solid particles to be floated, is accomplished. The particle to be floated is assumed to have a properly prepared hydrophobic surface prior to flotation. Upon leaving the three-phase mixing region, the "floatable particle-air bubble matrix" and

Jan 7, 1982

By V. P. Petrov, V. S. Znamensky

There are a great number of asbestos deposits in the USSR, and some are quite large. The main deposits of chrysotile asbestos are shown in Fig. 1. The Bazhenovo deposit, which is located in the Sverdlovsk region, is the largest and has been mined since 1889. Systematic studies of asbestos deposits were begun from the very be- ginning of Soviet government and are most often connected with the names K.E. Tarasov, P.M. Tatarinov, B.J. Merenkov, N.D. Sobolev, F.V. Syromjatnikov, V.N. Lodochnikov, V.P. Petrov, V.P. Eremeev, L.A. Sokolova, V.R. Artemov, and V.F. Dybkov. Investigations by these people and others helped the USSR be one of the most important producers of asbestos in the world. In this chapter, the main asbestos deposits of the USSR are explained in a general outline from the point of view of their genesis, common features, and differences that must be taken into account for forecasting, exploration, and the mining of asbestos. All chrysotile asbestos deposits of the USSR were formed from magnesium rock as a result of comparatively low grade temperature, hydrothermal alteration, and free crystallization of fibrous chrysotile in open cavities that served as catalysts. Chrysotile, a widely distributed rock-forming mineral, is not in general an important mineral for industry as it is a long fibrous and main vein variety. However, it must serve for geologists as an important prospecting criteria. And, the geologist should search for the mineral not only in places of possible chrysotile generation, but in places where asbestos may be crystallized in its long fibers. The Soviet geologists distinguish chrysotile asbestos deposits in two groups: (1) ultrabasic rocks and (2) sedimentary dolomite terranes, taking into account how the maternal rock was affected by hydrothermal solutions. The largest deposits are related to ultrabasite. In dolomite, the largest deposits are small and their asbestos contains almost no iron, which makes it a better filler for insulating plastics. There are a few types of asbestos deposits within the limits of the ultrabasic group, the largest being a Bazhenovo type to which the deposits of the Urals are attributed. This Bazhenovo asbestos is characterized by the most complete zonality of disposition for various kinds of asbestization. These types of deposits are, for the most part, the only ones presently working in the USSR. The Bazhenovo deposit is connected to the gabbro-peridotite intrusive belt that is about 180 km long and is broken into a number of fault blocks as shown in Fig. 2. Granitoid veins of intruded rocks are found along the deepest faults, and were sources of hydrothermal solutions that affected the maternal rock. The nearest granitoid vein, ultrabasite, is substituted by listwanite that consists of quartz, talc, carbonate, and some other essentially talcous rock. The next zone of hydrothermal alteration is composed of serpentine. The boundry between serpentinite and unaltered ultrabasite is as irregular, diffuse, and rough as the boundaries between all other zones. Nearer the vein of granitic rock, ultrabasite is entirely serpentinized into massif serpentinization that penetrates through cracks and fissures. There is an unaltered ultrabasite space between fissures, and the biggest block is preserved unaltered in the central part of the massif. The Soviet geologists call this ultrabasic sopka. Preservation of the unchanged blocks is of great importance for deposit formation as volume changes are impossible during the process of asbestization and serpentinization. It may be confidently said that asbestization in Bazhenovo type deposits is possible only when alteration of ultrabasite has not completely occurred. Under conditions of massif volume, a very big mass of substance must be carried out of the ultrabasite for the progressive stage of serpentinization. However, in the regressive stage,

Jan 1, 1986

By Edward W. Long

The Density Separator is basically a hindered settling classifier with automatic control features that provide steady, sharp classification irrespective of extreme variations in dry tons per hour of feed solids up to the design maximum throughput for the particular material being treated. The size and capacities of commercially available units and operating data comprise the scope of the paper. Applications of the unit for other than classification are proposed, i.e. washing and desliming.

Jan 1, 1982

By Garry W. Stevenson

Data from many case histories reporting tunnel boring machine penetration rates in rock with unconfined compressive strengths greater than 70 MPa (10,000psi) are summarized. The case history data are useful for comparing estimated penetration rates with historic performance in similar rock types, particularly in granitic and metamorphic rocks. TBM exhibit higher penetration rates in sedimentary rocks than in granitic and metamorphic rocks. Data for the two groups of rocks are summarized separately.

Jan 1, 1999

By J. Alton Burks, James P. Rider

The ability to accurately predict the sound field is essential for the estimation of probable worker noise exposure. For this reason, the U.S. Bureau of Mines is researching computer- based analytical techniques specifically geared to calculate the spatial variation of sound pressure levels within common mining environments. Initial modelling efforts describing the user interface, the simulation of energy acoustics, and the graphical representation of sound pressure levels are presented in this paper.

Jan 1, 1993

By S. E. Clay, P. R. Taylor

A physical model for the diffusion and flow of gases through porous solids, which accounts for the random nature of individual gas molecules moving through a solid of definite structure, has been formulated. The model was solved using' the Monte-Carlo technique. It was then used to evaluate specific constants related to the dusty gas model and to describe the gas-porous solid diffusion phenomena. Experimental results were used to validate the stochastic model.

Jan 1, 1988

By James L. Parks

This paper describes improvements in SAG and AG mill liner designs and their cumulative effect on wear life and mill availability. Routine procedures used by many SAG and AG mill operators to improve liner life are reviewed. Guidelines are provided for estimating the time required to replace worn liners along with practical methods to reduce downtime for liner replacement. Finally, the effects of mill operating conditions on liner wear life and breakage are considered.

Jan 1, 1998

By José Salim, T. V. Subrahmanyan

The occurence of primary stratiform and vein gold deposits in the Precambrian rocks of Northeastern Brazil is discussed. The stratiform deposits are related to clastic sediments (quartzites and conglomerates). The veins are associated with quartz and sulfides and are structurally controlled by shear zones. The gold was recovered for a long time by small miners. Developmental programmes for large scale mining are now envisaged. The recovery problems and gold economics are also discussed.

Jan 1, 1988