Search Documents

By V. Dezelic, D. B. Apel

This paper describes the results of laboratory and field experiments conducted to determine the applicability of Ground Penetrating Radar (GPR) for the assessment of the strata thickness and for the identification of separation between bedding planes in stratified rocks. The knowledge about the extent of such separation in the roof layers and information about roof lithology can be used to determine the roof support requirements for underground mines where stratified rocks are present. The laboratory and field experiments were conducted at the Rock Mechanics Laboratory and the Experimental Mine at the University of Missouri-Rolla. The 1.5 GHz high resolution, shallow depth GPR antenna was used for all of the experiments.

Jan 1, 2004

By J. Koinig, K. Mussger, St. Reischl

Jet grouting is a viable supplementary measure for NATM tunneling in special softground conditions. In particular it is used as a type of forepoling to maintain face stability and to provide initial support for large openings until the shotcrete lining reaches sufficient strength. For this purpose cement grout is injected under high pressure through horizontal pipes outside of the tunnel perimeter and thoroughly mixed with the soil producing 1 to 3-foot diameter cylindrical beams. Excavation of the tunnel then proceeds beneath this umbrella of 40 to 50 foot long beams. Design and construction experiences from recent projects are presented for tunnels diameters between 30 and 50 feet in fill and alluvial and colluvial deposits.

Jan 1, 1987

By R. E. Wardwell, J. D. Nelson

The design of cover systems for reclamation schemes in tailings requires estimation or determination of tailings materials properties such as compressibility, shear strength, and consolidation characteristics. It is very difficult and expensive to obtain truly undisturbed tailings samples for laboratory testing. In situ testing methods have been developed for economically obtaining large amounts of information. Two of these methods are described, the piezocone and the flat plate dilatometer. Both of these methods provide a rapid means of detailed material identification in a nearly continuous fashion for the entire depth investigated. The equipment is described and typical data from a uranium tailings impoundment is presented. The results are compared and the advantages and disadvantages of these methods are discussed.

Jan 1, 1987

By S. P. Mehrotra, P. C. Kapur

A phase-species classification is suggested for the mathematical models of flotation kinetics. Important models are discussed and the structure of their rate constants and parameters is analyzed. Split or enhancement factors are formulated for different kinetic models. The steady state dynamics of the flotation circuits can always be described in terms of these factors. For simulation of circuits, feed is characterized in a formal manner starting from a multivariate distribution of particles in flotation rate, size and mineral content. Synthesis of optimum circuits which simultaneously searches for the best process variables and structural parameters from a generalized master network is described. Trends in the areas of search algorithms, role of middlings and feed identification etc. are indicated.

Jan 1, 1989

By Robert W. Wheeler, Richard G. Ames, Robert B. Reger

Introduction The use of diesel engines as an alternate power source in US underground coal mines has been a controversial step towards more efficent mining practices. Three areas of potential benefit are foreseen. First, diesel-powered mining equipment is believed to be more efficient, resulting in less occupational risk for any given amount of production. Second, diesels are believed to pose fewer intrinsic hazards, especially those related to fires and ignition of combustibles. Finally, several other health and safety advantages are foreseen for diesel units. Each of these issues will be discussed separately. Diesel Efficiency Proponents of the use of underground diesel-powered mining equipment point to increased production efficiency due to greater maneuverability, speed, power, and payload (Bradbury, 1973; Jorgensen, 1982; Ogden, 1978; Wenberg, 1979; Olsen, 1980). Units most suitable for diesel power include LHD vehicles, shuttle cars, personnel carriers, and maintenance vehicles. Estimates of increased efficiency vary from 60%-300% and more (Wenberg, 1979). Increased diesel mining efficiency is usually viewed as making it practical to mine lower grade seams. Diesel units can also operate over a wider range of floor pitches and distances than electrically-powered units, thus allowing mining of seams with special mining problems (Olsen, 1980). Diesel application is not a universal substitute for electrical power. For example, continuous miners are unlikely diesel candidates. Reduced Intrinsic Hazards Proponents of diesel use have pointed to the increased safety potential due to a reduction in electrocutions, arcs, burns, underground cable fires, and methane ignition (Ogden, 1978). Diesel units are frequently employed in maintenance activities for lifting and moving, and for coal cleanup. Thus the case is made that diesel use, by making powered operations more conveniently available, reduces the incidence of lower back injuries and related causes for days lost due to disability (Olsen, 1980). Several other issues relating to diesel safety have also been suggested. Diesel units can continue operation even during power outages allowing, for example, personnel evacuation. The maneuverability of diesel units make them particularly attractive in difficult physical conditions, such as long haulage from the face to the belt and in areas where water is deep. The case for diesel use focuses heavily on the potential for a "per worker" reduction in accidents, or a reduction in the severity of accidents. Since accidents are a major part of the health impact of mining, a reduction in accidents and resulting injuries would make a major contribution to the health of coal miners. Opposition to Diesel Use Opposition to the use of underground diesel mining equipment in the US seems to have started with the United Mine Workers of America. Some opposition to US diesel use has been based on a widely publicized 1976 letter from NIOSH to Mine Enforcement and Safety Administration administrator Robert Barrett (NIOSH, 1982). In essence, this letter warned that while insufficient evidence existed as to diesel effects on underground coal miners, NIOSH had concerns based on prior knowledge of separate diesel exhaust constituents and the potential for interaction between these constituents and coal mine dust. Current opposition to underground diesel use has focused on respiratory health effects related to diesel emissions, particularly nitrogen dioxide (NO,), carbon monoxide (CO), and particulate content (Barrett, 1982). Through

Jan 4, 1983

By R. K. Mehta, S. K. Dhar, R. R. Mallepali

Introduction The incentives for developing a distributed form of the comminution model include: • for describing the heterogeneous comminution behavior of multiphase mineral systems (i.e. realistic ore bodies, such as complex sulfide ores consisting of chalcopyrite, galena, sphalerite, pyrite and siliceous minerals) and •for generating, for various locked and free particles, in situ, microscopic, breakage behavior such as the mode of fracture (intergranular vs. transgranular), the relative rates of breakage and the breakage distribution. However, the computational difficulty and the effort made in estimating a large number of parameters (Andrews and Mika, 1975; Wiegel, 1976; Herbst et al., 1985, 1988) do not justify the utility of this approach. Also, obtaining the results experimentally is very tedious and time consuming if using this approach. Although recent work in this area (Choi, Adel and Yoon, 1987; Mehta, Adel and Yoon, 1989, 1990) showed good results for liberated particles, the quality of the estimation and prediction was poor for locked particles. Attributing this to the complex breakage behavior of locked particles, it was concluded that additional constraints, and possibly modification in the breakage distribution functional form for locked particles, were necessary. However, further mathematical analysis revealed that the method previously used was in error. The purpose of this technical note is to present the correct solution methodology used in solving the general model equations of a multicomponent mineral system containing multiple classes of locked particles. Previous work and connection The general form of the comprehensive, distributed-component comminution model has been described as (Herbst et al., 1985) [d (m (0) -[ I - B ] S_ m(t) = A m(t) (1)] where [A] is the fundamental matrix/state companion matrix, commonly referred to, in the comminution literature, as the "mill matrix." Note that for a distributed-component comminution model, this is a full, general, real matrix, unlike a lower triangular matrix for a simple grinding model or a lumped-binary grinding model with one locked-particle class (Herbst et al., 1985, 1988). Also note that all of the underlined letters refer to matrices. Herbst et al. addressed the difficulty in arriving at a closed form of the analytical solution of Eq. (1) via similarity transformation [IT J inv (T)]]. This difficulty occurs for several reasons: •[A], as a general real matrix, may have complex eigenvalues and complex eigenvectors. •More importantly, there is no guarantee that a set of eigenvectors of [A] will turn out to be independent. An attempt was made to solve this problem by implementing a decomposition method. With this technique, the mill matrix was decomposed into a sum of lower and upper triangular matrices [(i.e., A = L + U)]. Then the solution was obtained using similarity transformation (Mehta, Adel and Yoon, 1989, 1990). [e(At) = e(L+U)t = e(Lt).e(Ut) _ [ TL Jt- (t) inv(T_L)] [-Tu Ju (t) inv(Tu)]] [But, unfortunately, e 1+U = e t . eu is true only for scalars and not for matrices (i.e., eL+u# eL- eU) unless they commute. In other words. eAt = e(L+u)t= ekt - eU' if LU = UL. Hence, this decomposition scheme must be replaced by a mathematically acceptable method known as the "splitting method"]

Jan 1, 1994

By William W. Wellborn

Abrasives are substances both natural and synthetic that are used to grind, polish, abrade, scour, clean, or otherwise remove solid material usually by rubbing action (as in a grinding wheel), but also by impact (pressure blasting). Facts about the discovery, early use, adaptation, and development of abrasives prior to the 20th century are few. From the sparse, earliest information that is available, it would appear that the science of abrasives began when, to fashion his tools, man began to select certain kinds of rocks in preference to others because of their peculiar properties. There is evidence that stones were sawed by some sort of grinding machine as early as 4000 BC in Egypt. The real expansion of abrasives use coincided with the beginning of metallurgy in the Middle East around 2000 BC. The earliest confirmed use of abrasives for grinding metal comes from a steel dagger found along with a sharpening stone which was dated at about 1500 BC. Natural and manufactured abrasive substances play an important role in fashioning and finishing numerous products with a wide variety of end-use applications. The mining and preparation of crude, natural abrasives for their markets and the manufacture of synthetic and other abrasive materials contribute significantly to the US economy (Table 1). In addition, just as sawing to specific dimensions enhanced the value of the Egyptian stone, the use of abrasives in fabrication of modem products, and the addition of abrasives to others, add value. GENERAL CONSIDERATIONS The most important physical properties of materials that qualify as abrasives are hardness, toughness (or rigidity), grain shape and size, character of fracture (or cleavage), and purity (or uniformity). To fabricate bonded abrasive products such as grinding wheels, additional considerations include stability under high heat and bonding characteristics of grain surfaces. The economic factors of cost and availability are always important. No one singular property is paramount for any use. For some applications extreme hardness and toughness are needed, as in diamonds for drill bits. For other uses, factors of greatest importance are hardness and ability to break down slowly and, in the process, develop fresh cutting edges when grains become worn. In garnet sandpaper, for example, highly cleavable, friable, or extremely tough grains are not desirable. For other uses, extreme hardness may be objectionable. Abrasives for dentifrices and for glass-cleaning soaps are cases in point. For the most efficient uses in more critical applications, different types of abrasives are rarely completely interchangeable. While crushed quartz and garnet are both used in sandpaper, the two abrasives are not at all interchangeable in their applications. In the final analysis, the choice of a high-grade abrasive depends upon the quality and quantity of work performed by the abrasive per unit of cost. Initial cost of an artificial abrasive may be much greater than that of a natural abrasive, but the artificial mineral may do so much better work and do it so much faster that the ultimate cost is less. It is for this reason that artificial abrasives have largely replaced natural abrasives.

Jan 1, 1994

By V. N. Kelly

The ability to link geological sections on a graphics screen to form three dimensional geology representation was implemented at Kidd Creek in 1987. This technique affords an opportunity to optimize metal estimation in ore at the Kidd Creek copper, zinc and silver mine, by applying enhanced interpretation methods. On a series of geological sections varieties of ore are outlined. These are linked from section to section to form polyhedra which closely simulate the three dimensional shapes of the different ore types referred to as mintypes. The orebodies are divided into zones, referred to as domains, that approximate the function of variograrns, for which' preferential continuity of mineralization has been estimated for distances in the width, strike and dip directions. These distances define ellipsoidal volumes of influence. The domains are also linked into polyhedra. Both types, coded by ore variety and zone, are mapped into the block model. Tonnage and metal values are calculated for ten-foot cubical cells of the block model by any of several estimation methods under domain control. In estimating the metal grades for a cell the predetermined search ellipse is applied to select only those drill hole assays of the same mintype as the cell designation. Once grade estimations have been determined for the cubical cells comprising the model, a wide range of stored information can be viewed. For example, in plan at any row elevation or on vertical section at any azimuth, as either printed values for the cells or as contoured data. This flexibility is of particular value in checking and refining the geological interpretation to better conform to ore types and grades actually mined. Combined with three dimensional geological modelling, and correctly chosen domains, the use of mintypes implants essential geological control into the system and prevents assays for one ore type from affecting grade estimation in adjacent ore types. The three dimensional geological modelling and block model segments provide information which is effectively applied to the stope design, production, planning and control parts of the system.

Jan 1, 1989

By Jianmin Qin, Raja V. Ramani, Wilson Miola

The number of underground work entities operating under reduced dust standards in U.S. coal mines has been increasing since the start of the decade of the 80s and is currently approaching 10,000. The concern for controlling the quartz levels in airborne respirable dust in coal mine has manifested itself in several improvements in equipment selection and operation, face ventilation practices, and dust control procedures. At the same time, fundamental studies have been initiated on determining the source-sink relationships of the airborne quartz dust. The P-7 method is the prescribed method for the determination of quartz in the respirable airborne dust samples from coal mines. Questions have been raised on the reliability of the P-7 infrared spectrometry method for quartz analysis in powders. No specific method has been defined for quartz determination in bulk samples from the mine. In a recent study on the relationship between quartz in the airborne dust and that in the materials being mined, both infrared (IR) and x-ray diffraction (XRD) methods were used on a suite of samples from several coal mines. These samples encompassed airborne respirable dust samples, airborne total dust samples, the oversize fraction from the respirable samplers, ROM samples, channel samples, and chip samples from the face, roof, and floor materials. In this paper, the sample preparation and analysis procedures for the samples are discussed. The data, analysis results, and comparisons of the P-7 and XRD results are presented. The quartz percent determined for the same sample by the two methods are different. In 85% of the samples analyzed, the quartz percents determined by the XRD method are higher than those obtained by the P-7 method. However, there is a strong linear relationship between the results from the two methods. Further, the XRD method indicates an average of 20 percent more quartz than that from the P-7 method. The reasons for the differences in the results and the need for additional studies are explored.

Jan 1, 1991

By S. Afrouz, C. Keles, E. Sarver, A. Greth

While respirable dust monitoring has long been done on the basis of mass concentration, it is increasingly recognized that specific dust characteristics may play an important role in health outcomes. Scanning electron microscopy with energydispersive X-ray (SEM-EDX) can be used for detailed particle analysis, but the quality of results can be dependent on the sample substrate; ideally, particles should be deposited on a smooth, uniform substrate like polycarbonate (PC). While direct air sampling onto PC filters is possible, this is not the standard approach in many situations. For example, in coal mines, polyvinyl chloride (PVC) filters are often used. They enable conventional mass-based analysis — of the total respirable dust, and the content of crystalline silica in this fraction — but are fibrous and thus not ideal for SEM-EDX or other microscopy. To address this issue, the current work tested a simple method to recover respirable dust particles from PVC filters and redeposit them to PC. Results generally indicated that recovered particles are representative of the original dust sample in terms of mineralogy distributions. Where this was not the case, the issue appeared to be with high particle loading density during SEM-EDX work rather than related to the recovery/redeposition method itself. This bodes well for applications where a single PVC filter sample could be used for nondestructive analysis to determine respirable dust mass and/or respirable silica mass, followed by preparation for SEM-EDX analysis to evaluate particle characteristics. The recovery and redeposition method might also be adapted for other applications, such as to enable the analysis of respirable dust samples collected by the continuous personal dust monitor (CPDM).

Oct 1, 2024

By Kim A. Lapakko, William W. III White

The ASTM standard method D 5744-96 was developed to provide a well-defined kinetic test protocol, conducted under controlled reaction conditions, with the intent of generating reproducible results. A preliminary indication of the repeatability of a simplified alternative method (MN DNR method) was assessed and results from the MN DNR method were compared to those from the ASTM method. To provide an indication of repeatability, six samples from three different rock types were subjected to dissolution testing for periods of 20 to 68 weeks. Drainage pH values at the end of the tests were within 0.5 units in all cases and within 0.05 units in four cases. The percent difference from the mean for overall sulfate rates from paired cells ranged from 0.04 to 1756, with a median of 6.3%. Nine samples from four rock types were subjected to both MN DNR and ASTM tests for periods of 20 to 132 weeks. The difference in final drainage pH values forsix of the samples was less than 0.1 unit, and these values were less than pH 3.65 or greater than pH 8.0. The final drainage pH difference for the last three samples ranged from 0.15 to 0.4, and these values were ill the pH range of 6.2 to 7.2. The sulfate release rates for the periods of record for the MN DNR method were 70 to 150% of those for the ASTM method, with a median value of 110%. Sulfate and calcium release from the two methods was not substantially different. The MN DNR method typically produced higher magnesium release.

Jan 1, 2000

By Christopher J. Hall

This paper describes the results from computer runs simulating 24 different mine ventilation configurations with the main fan situated first at the top of the upcast shaft and then at the top of the downcast shaft. Real air was used, with evaporation, condensation and heat exchange. The results showed that power requirements for the forcing fan were up to 20% less than for the exhausting fan for equal mass flow rates.

Jan 1, 1989

By R. Codell, D. L. Hughson

The authors benchmarked the integrated finite-volume code MULTIFLO against the analytical solution of Philip et al. (1989) for cylindrical underground openings. They found that the numerical simulation of dripping threshold flux was consistently higher than the analytical solution for rectangular and unstructured grids. The magnitude of this error was proportional to the alpha parameter characterizing capillarity. This error may bias estimates of seepage into drifts for repository performance towards nonconservatism.

Jan 1, 2002

By Ora H. Rostad

Some gold production was obtained from placer deposits in Puerto Rico during the period of Spanish colonial rule, but most of the gold was produced prior to 1536. There had been no significant hard rock mining, other than in quarries for road metal or construction purposes or for raw materials to make cement, prior to 1954 when the government of the Commonwealth of Puerto Rico recognized that changes in the mining code were necessary to stimulate exploration for metalliferous ore deposits. The Puerto Rican Legislature passed an act (No. 6), which was approved on Oct. 6, 1954, that reiterated that the title to all "commercial minerals" is vested in the Commonwealth of Puerto Rico. The act provided for the establishment of a Mining Commission, stipulated the power% with which the Mining Commission was vested, and provided that no one may dispose of "commercial minerals" in Puerto Rico without a Commonwealth grant issued on its behalf by the Mining Commission. Act No. 6 also provided for prospecting permits, mining leases, and grants. The Mining Commission, by authority granted to it by Act No. 6, adopted regulations effective Nov. 21, 1957, relating to prospecting, leasing, and producing commercial minerals in Puerto Rico. Royalty rates were also specified for various types of deposits at different annual tonnage production levels.

Jan 1, 1991

By B. J. I. Adair, K. R. Weller

The bulk scavenger tailing from Aberfoyle's Hellyer Concentrator, which represents about one-third of the total tailing, runs about 2.5-3 g/t gold and 140-200 g/f silver. Both values are very finely disseminated, particularly the gold. Aberfoyle wished to establish whether ultra-fine grinding followed directly by cyanide leaching could be applied to the tailing for recovery of gold and silver. The work comprised the determination of gold and silver recoveries as a function of grind size and leaching time, the specific energy consumption required for continuous wet grinding of the tailing to the specified product size in a small horizontal continuous stirred mill, and an estimate of the rate of media consumption. The maximum extraction of gold, 23.3% was obtained from the finest product, with the highest cyanide concentration and longest leach time, confirming earlier work. A similar result was obtained for silver. The specific energy requirement for milling rose from 27.7 kWh/t for a P80 of 8.1 um to 219 kWh/t for a Pea of 2.3 um. The consumption of ceramic media was about 1.6 g/kg of final product. An extensive QEM'SEM Trace Mineral Search on the unground tailing failed to identify any gold-bearing particles but did identify silver-bearing particles which displayed a variety of textural associations and liberation characteristics.

Jan 1, 1998

By Guiseppe Bonifazi

This work applies the definition of "separation function" already introduced in the paper presented at the XVIII IMPC. This 'function" (defined for a certain size distribution after comminution of an ore) refers to the recovery distribution of a mineralogical species in a product made up of all the particles having at least a given content of that species. Many tests would be required to determine the liberation function for each mineralogical species, particularly for complex ores. Several stages of comminution would need to be examined and the mineralogical composition of the particles of each grain size class would need to be analyzed for each process step. A quick and dirty method is shown for obtaining the "separation function". It is based on the processing of data from topological maps of polished and/or thin representative sections of ore. By superimposing grids of different sizes over these maps and with appropriate combinations of mesh sizes, it is possible to simulate the grain size distributions linked to different stages of comminution and then evaluate the mineralogical composition of each grain. The procedure is carried out full automatically and can simulate a complete treatment circuit, imposing cut-off grades for the products at each separation phase. It is also possible to predict the results of treatment processes that involve grinding phases. The procedure has been successfully applied to complex ores containing several useful components.

Jan 1, 1995

By John R. Thalimer

For the past four years the U.S. Bureau of Mines has investigated the early detection of insulation failure in squirrel cage induction motors. Data modeling techniques based on values calculated from a motor's voltage and current phasors were used to produce a pair of polynomial equations that calculate a motor's insulation leakage current and power. This paper describes a prototype system using these models that monitors six motors on a continuous miner for insulation leakage in order to anticipate insulation failure. The system consists of a motor-data system for each motor on the machine, a control computer located some ' distance from the miner, and a serial bus to interconnect these items. Each motor-data system consists of an analog interface to the motor's voltages and currents, a single-board computer that reads digitized data and calculates voltage and current phasors, and a bus node that interfaces the single-board computer with the serial bus. The control computer can request and receive phasor data from any motor-data system on the bus. Using models developed at the Bureau, the control computer calculates and displays two deterioration values for each motor, one for leakage current and the other for leakage power. These values are then stored into a database from which the user can display them over time.

Jan 1, 1992

By L. J. Nicks

The current U.S. Bureau of Mines research program is addressing the recovery of flake graphite from kish, a steelmaking waste product, and the use of zeolites from abundant domestic natural deposits for efficiently cleaning up mining industry wastewater. The United States is almost totally dependent on imports for its graphite needs, but this may change depending upon the results from a pilot plant being constructed by industry using Bureau technology. Standard mineral processing techniques were applied by the Bureau to recover high-quality flake graphite from kish. It was considered innovative enough to receive an R&D 100 Award in 1992, and its commercialization has the potential to supply the total U.S. demands for graphite many times over. Zeolites have ion exchange properties similar to ion exchange resins, but are less expensive and available in large quantities. Samples of naturally occurring zeolites were tested for their efficiency in removing metal ions from synthetic and industrial waste solutions. The tests focused on defining their selecting, loading, eluting, and regenerating characteristics, and on developing a method for recovering the metal ions as added value products. The results showed that the removal of metal ions with zeolites from acid rock drainage (ARD) solutions is technically feasible and that this technique has the potential for being used in an integrated chemical treatment systems approach either as a primary or secondary cleaning step.

Jan 1, 1995

By Felicia F. Peng

In operation of column flotation of fine coal, the smaller bubbles are required to effectively recovery of fine hydrophobic particles. However, smaller size bubbles alone does not ensure an efficient flotation for fine particles. The sufficient available bubble surface area per unit column are essential for effective column flotation. The experiments are conducted in a lab-scale column using two different bubble size distributions and three different particle size distributions for flotation of Pittsburgh No.8 seam coal. The interaction between particle size, aeration rate, feed rate and wash water addition are examined in this investigation to establish the optimal operation conditions for flotation of fine coal. Despite of wide range of operation conditions used in this study, it is found that the experimental data fall in a single characteristic recovery-ash curve for a given bubble size distribution and particle size distribution. The major parameters affect the flotation performance points along -the characteristic recovery-ash curves are aeration rate/frother dosage, feed rate and wash water rate-.

Jan 1, 1994

By Michael J. Virnig, Murdoch W. MacKenzie, Michael R. Davis

The objective of this paper is to present preliminary capital and operating cost estimates (±25%) comparing conventional carbon-in-solution (CIS) with resin-in­solution (RIS) using AuRIX® 100 for the recovery of gold and silver from typical heap leach solutions. Preliminary testwork was carried out with AuRIX® 100 using real and synthetic leach solutions to determine the technical viability of the resin for gold/silver recovery and to provide process design parameters for the preliminary RIS circuit. The scope of the resin testwork was sufficient to support the level of accuracy applied in the capital and operating cost estimates. No parallel testwork was carried out with activated carbon. Industry standard design data and operating data from existing CIS operations were used as a basis for the comparison. Both the capital and operating cost comparisons indicate a substantial savings for a RIS circuit using AuRIX® 100 (- 14 to 18% in terms of capital and 25 to 35% in terms of operating costs) over a conventional CIS circuit depending upon solution flows and grade.

Jan 1, 1999