Search Documents

By C. Roldan, C. Garcia, J. D. Miller, C. L. Lin

The ultimate recovery in a heap leaching operation is related to the degree of exposure of the valuable minerals in comminuted particles. Recently, high-resolution cone beam x-ray microtomography (XMT) has been used to determine this parameter. XMT technology consists of examining the extent of mineral exposure for each size fraction of ore in 3D, then, by algebraic calculations, the ultimate recovery can be estimated for different particle size distributions (PSD). To confirm the usefulness of the XMT technology for mineral exposure analysis, column tests were performed to determine ultimate recovery using three PSDs for two composites obtained from the copper heap leaching operation at Zaldivar-Chile.

Jan 1, 2003

By N. P. Reddy, Y. J. Wang

Stall or aerodynamic stall of axial flow fans has long been recognized as an important operational problem in mine ventilation. To develop a technique for characterizing fan stall in multiple fan ventilation networks, a research project was initiated through the Generic Mineral Technology Center for Mine Systems Design and Ground Control. Considering that fan stall is related to multiple operating points, this paper discusses a numerical model for multiple fan ventilation networks, and numerical methods for solving multiple networks solutions. It is hoped that the results of this project will lead to an innovative method of ventilation network analysis and simulation, thus preventing stall.

Jan 1, 1993

By R. L. Lewis

A simple method for estimating the steady-state water quality of a pit lake is presented. The steady-state concentration of a conservative chemical constituent in a pit lake is shown to be a simple function of the inflow rate, the evaporation rate and the inflow concentration. An analytical method is presented for estimating the equilibrium ground water-inflow rate for use in water-quality predictions. The time required to reach chemical steady state is estimated using an iterative mass-balance model. Mine operators should find the methodology useful for planning and screening regulatory applications where conservative estimates of pit lake water quality are desirable.

Jan 1, 2000

By G. Pierson

Explanations for commodity price levels (or movements) commonly focus on the fundamentals of supply and demand otherwise they are simply assigned to speculative activity. Comparisons of metal-price histories to monetary and other economic data support the argument that the supply of and demand for money are no less important in the determination of price than are the supply and demand of the commodity itself. That these relationships should exist is evident in the price identity and they are consistent with monetary theory. The patterns developed have limited usefulness as predictors, but their recognition is essential for the construction of price scenarios for planning purposes.

Jan 1, 1998

By G. Pierson

Explanations for commodity price levels (or movements) commonly focus on the fundamentals of supply and demand, otherwise they are simply assigned to speculative activity. Comparisons of metal-price histories to monetary and other economic data support the argument that the supply of and demand for money are no less important in the determination of price than are the supply and demand of the commodity itself. That these relationships should exist is evident in the price identity and they are consistent with monetary theory. The patterns developed have limited usefulness as predictors, but their recognition is essential for the construction of price scenarios for planning purposes.

Jan 1, 1997

By J. Andersen

The very large quantities of energy used for size reduction in the minerals processing industry necessitate the accurate prediction of comminution machine power draw for optimum plant design. The JKMRC has developed effective models for predicting ball mill, autogenous mill, semi- autogenous mill and crusher power draw. When combined with comminution models they provide a powerful tool for evaluating not only the size reduction performance of a plant design, but its power utilization efficiency as well. This paper describes the structure of the mill and crusher power models. Data from a wide range of equipment types are presented which illustrate the accuracy of these models.

Jan 1, 1992

By J. B. Hiskey, P. H. Qi

Activated carbon loaded with gold from different halide solutions was characterized by thermal analysis (TA) techniques. The mechanism of gold uptake by carbon varies from predominately adsorption for gold iodide to predominately reduction for gold chloride. Thermogravimetry analysis (TGA) and differential thermal analysis (DTA) measurements confirm the existence of adsorbed gold-halide species within the micropore structure of carbon. These results suggest that the ratio of reduced to adsorbed gold increases for gold halides in the following order: Au-I < Au-Br < Au-Cl. In the case of Au-I, TA results for the loaded carbon were compared with pure compounds of 12, Aul and Aul3.

Jan 1, 1998

By Jim Morris, Davin Ishii

The major source of water for Southern Nevada is Lake Mead. However, the existing pump station located on Lake Mead is inadequate for one of the fastest growing areas in the United States. In order to keep up with the increasing demand for water in Las Vegas, a parallel system is being constructed. The intake for this system is being constructed approximately 68.58m (225ft) below the surface of Lake Mead. The lake tap consists of installing casing and secant piles to support the shaft collar, excavating a 21.34m (70ft) deep intake shaft, and installing a3.66m (12ft) diameter steel liner.

Jan 1, 1999

By Thomas H. Hibner, Daniel Tempelis, John E. Shamma

Environmental protection of nearby resources is an issue that can not be ignored in tunnel construction. The Inland Feeder Arrowhead Tunnels Project is no exception. With keen interest from various stakeholders, Metropolitan developed a Groundwater Monitoring and Mitigation Plan. This plan provides for monitoring and management of selected water resource features within the San Bernardino National Forest along the proposed tunnel alignment. The plan specifically provides for monitoring of streams, springs, seeps, and piezometers for water temperature, pH, specific conductance, and chemical analyses, as well as flow or groundwater elevation. Metropolitan uses the data to evaluate for and manage potential impacts from groundwater ingress during construction of the Arrowhead Tunnels.

Jan 1, 2003

By M. J. Senk, A. Lusin

Federal regulations require that methane liberated at the face be diluted and removed to maintain methane gas concentrations below 1pct (CFR) in working places and intake air courses. The delivery and distribution of intake air at the face is critical for effective face ventilation. Improved techniques for monitoring the movement of intake air to the face are needed. A test system was developed and a computer program written for using a three-axis ultrasonic anemometer to measure airflow in a simulated mine entry. Results of tests conducted in the entry showed that the anemometer is a valuable tool for measuring mine airflow conditions near the face.

Jan 1, 2003

By Richard B. Muter

In determining the layout or combination of unit operations to be utilized in a modem preparation plant, several factors must be taken into account. Among these are the washability data, size consist data, the particular market or markets for the coal, the mining method used, the degree to which the coal must be prepared, expected fluctuations in raw coal and markets, and the overall economics of the process. In addition, there are the health and safety aspects of coal utilization and preparation. Chapter 1 of this book discusses the characteristics of coal and coal markets, while Chapter 2 deals with the design of preparation plants. Once the unit operations for a particular plant have been decided upon, these arrangement may be depicted by using a flowsheet. A coal preparation plant flowsheet is a two-dimensional graphical representation of the sequence of operations, the arrangement of machinery, and the flow of materials for a particular coal cleaning operation. The flowsheet is usually qualitative in nature, becoming more quantitative as material balances, water balances, numbers and sizes of various pieces of equipment, etc. are added. The usual convention in preparing a flowsheet is to show the feed flowing from left to right, starting at the top left and working down as in an all-gravity process. Various symbols are used for each unit operation as depicted on a flowsheet, and Fig. 14-37 is a compilation of the commonly accepted international standard symbols for each unit operation. Fig. 14-38 through Fig. 14-40 are flowsheets of various coal cleaning processes as published in the January 1976 issue of Coal Age. Each process has its own unique features which, among others, depend upon the coal being cleaned, the coal market, and the mining operation. Fig. 14-38, for example, is a flow diagram for a jig plant preparing steam coal from two strip mines located a few miles apart. In addition to the jig washer, cyclones are used to treat the finer size coal. Fig. 14-39 is a flowsheet of a heavy media plant using a heavy media washer for + %-in. (+6.3-mm) coal, froth flotation for -28 Tyler mesh (-0.6 mm) material, and dewatering phase units (dwp) for Y, in. x 28 Tyler mesh (6.3 x 0.6-mm) cleaning of steam coal. In addition, thermal drying, centrifuge drying, and the use of vacuum disk filters and thickeners for dewatering are depicted. Fig. 14-40 is a flowsheet of a plant producing metallurgical coal. In addition to the heavy media and froth flotation circuits, a tabling circuit is also employed. These flowsheets are intended to give the reader an example of how the various unit operations for coal cleaning may be linked together. Figs. 14-41 and 14-42 illustrate the conversion of block diagrams into an IS0 prescribed set of symbols.

Jan 1, 1991

By C. W. Schultz

The Mineral Resources Institute at The University of Alabama is engaged in a program whose objective is to develop a beneficiation system for Eastern oil shales. Prior experience (1,2) at The University had shown that the grind required for liberation of the oil rich kerogen was substantially below 20~m. Based on this fact and the rapidly emerging consensus that column flotation is the preferred method for ultrafine particle separation, efforts were focused on the column flotation of oil shale. This paper, which must be regarded as a progress report on a continuing MRI project, describes the observations made and the results achieved to date. The investigation is being conducted in two phases. The first phase has been completed and consisted of a factorially designed experiment conducted for the purpose of screening a set of primary flotation variables. The second phase, which is still in progress, is focused on optimization of the operating conditions and development of a flowsheet for specific shales.

Jan 1, 1989

By Richard E. Barrett

The relationship between coal characteristics and power plant performance has become a matter of increasing interest to utilities. This relationship can affect the value of coals, decisions as to coal washing, setting penalties for delivery of coal that fails to meet specifications, and justifying buying better coals (at higher costs) before public utility commissions. The study described in this paper was directed to identifying how coal characteristics impact on boilers and related coal and gas handling systems. TVA data for the period 1962-1980 was the basis for the study. Models were developed for boiler efficiency, boiler availability, and maintenance costs as a function of such coal characteristics as ash, sulfur, and moisture content and boiler age. Boiler load and maintenance efforts were considered as variables in some of the models, but were found not to be statistically significant. Although the results of this study are strictly applicable to only the TVA system, they can serve as guides or first approximations for other utilities.

Jan 1, 1983

By Lyda W. Hersloff

As decommissioning of various radioactively contaminated facilities begins, the question of appropriate residual surface contamination becomes an issue. Surface contamination can result in exposure to people via inhalation, ingestion, and external radiation exposure, There is therefore the potential of exposure to workers involved in the dismantling of a facility as well as members of the general public acquiring salvageable equipment, tools, and building materials. The levels established as acceptable for unrestricted use by national and international organizations vary by as much as an order of magnitude for certain radioactive materials. The calculated doses associated with some acceptable contamination levels can be significant. The principle of ALARA, as low as reasonably achievable, is therefore a necessary element in establishing surface contamination levels for a specific site. Some components in evaluating site specific surface contamination levels for unrestricted use, especially removable contamination, include evaluations of the historical use of a facility, the mixtures of radioactive materials a&sociated with surface contamination, and resuspension factors for various materials.

Jan 1, 1991

By Andrew P. W. Briggs, Corale L. Brierley

A considerable economic and technical knowledge base has been amassed with the successful and sustained operation of commercial minerals bioleaching/biooxidation plants to extract copper from chalcocite ore and enhance precious metal recovery from sulfidic refractory ores and concentrates. Economic evaluation ofbio-processing must consider the value of the ore, the sulfide-sulfur requiring oxidation to achieve significant metal recovery, the time required for the biological process and, in the case of precious metal feed-stocks, the down-stream reagent consumption. Of these considerations oxygen requirement for the biologically-catalyzed oxidation of sulfide minerals is the prevailing determinant in the capital and operating costs of aerated, stirred-tank reactors for processing concentrates and bio-heaps for processing ores. Oxygen requirement is dictated by the amount of sulfide-sulfur requiring oxidation to achieve desired metal recovery. The testwork program to evaluate a project for application of biooxidation/bioleaching must be designed to insure that factors critical to economic assessment are fully quantified.

Jan 1, 1997

By Peter M. Turcic

A Mine Safety and Health Administration (MSHA), National Institute for Occupational Safety and Health (NIOSH) and Bureau of Mines (BOM) interagency task group was established to assess the health and safety implications of the use of diesel-powered equipment in underground coal mines. The objective of the group was to conduct an assessment to identify areas of concern, to evaluate the adequacy of existing methods for addressing the identified concerns, and to recommend agency approaches for addressing inadequacies. The interagency group concluded its work in April 1986 and presented a report to the Assistant Secretary for Mine Safety and Health. The report included the conclusions reached by a group and recommendations for regulatory action by MSHA. This paper will present the methods and approaches used by the interagency task group and will discuss the findings, conclusions and recommendations of the group. The paper will attempt to meld together the technical and policy aspects of the issues involved with diesel equipment in coal mining.

Jan 1, 1987

By N. Roqueñí, J. Loredo, F. Pendás

Impacts of mining on surface water and groundwater occur frequently not only in active mines but in abandoned mines, then the establishment of effective legal mechanisms for the regulation and control of mine waters is a necessary step in order to avoid pollution from mine waters and in consequence to contribute for a sustainable development of the mining industry. Currently there is a lack of a specific European legislation about mine waters and this absence of legislation occurs too at national level in many European countries. This absence of an European specific regulatory framework for mine water pollution questions the effectiveness and the applicability of the current legislation and this fact has led the EC to put forward proposals legislation to adequately deal with environmental and social consequences of mining, and among those proposals is a draft for a directive on waste from the extractive industry that includes provisions for mine water pollution.

Jan 1, 2005

By Robert M. Cox

The principal factor that must be determined for the effective design of a coal mine roof bolt support system is the maximum stable tension that can be developed with a given bolt assembly in a particular roof rock. There are four basic types of roof bolt anchorage techniques available: (I) the splitwedge; (2) mechanical expansion units; (3) resin point anchors or grouted expansion units; and (4) the cone shell which is placed in a reamed hole. A study of this problem has been made which includes theoretical analyses, laboratory experiments and field tests. A static free-body analysis of each of the anchorage techniques has provided formulas for predicting the anchorage capacity for a particular rock from the results of standard pull tests. The formulas also provide an insight into the anchorage mechanism of technique and allow for a comparative evaluation of the methods for design purposes. The theoretical analyses also indicate clearly the pertinent variables affecting the anchorage mechanism of each method.

Jan 1, 1977

By Klados. T.

MSC.Software assessed the performance of the drive end and non-drive end bearings on a ball mill using the finite element method. The assessment included the effect of mill and pedestal deformation on the performance of the bearings. Oil film thickness, oil pressure distribution and power requirement were of interest. A solution approach coupling a structural solver to a Reynolds equation solver was specifically developed for the project. Results showed that the deformation of the bearing surfaces had a significant influence on the performance of the bearings. For example, for the non-drive end bearing, the minimum oil film thickness computed for the deformable bearing surfaces was significantly lower than calculated for the non-deformable case. The results also showed that cavitation was likely in both the drive end and non-drive end bearings (severe negative pressures were obtained in both bearings). Other design variations were also assessed, e.g. a case with a modified radial clearance which improved the results.

Jan 1, 2006

By James L. Crowe

Electric-power-generating plants fired by fossil fuels are faced with increasingly stringent requirements for control of sulfur emissions. Several approaches for limiting these emissions, or for operating such facilities in an environmentally acceptable manner, are being pursued. Some of the approaches are based on the use of naturally occurring carbonate rocks or of materials derived from them. This paper discusses primarily the carbonate-rock-based processes being developed for control of sulfur dioxide emissions from fossil-fueled electric-power-generating plants. It includes a discussion of the role of carbonate rock materials in removal of sulfur dioxide from stack gases after combustion, capture of gaseous SO2 during the combustion process, and removal of sulfur from fuel prior to complete combustion. Materials derived from carbon- ate rocks are generally used in processes which convert the sulfur to a throwaway product, but there are also proposed processes in which the sulfur is converted to a useful product and the absorbent is regenerated for reuse.

Jan 1, 1974