Search Documents

By Harold E. Rowen

The listed title of my talk to-day is "MODERN ON STRAND SINTER COOLING". Perhaps it should he ve been "COMPLETION OF SINTERING ON THE STRAND" as the two are synonymous. By the very nature of the DWIGHT-LLOYD SINTERING PROCESS partial cooling on the strand is always present, but not completion of sintering and cooling on the strand. I have mentioned the Dwight-Lloyd process just to be certain the type of sintering under discussion is fully identified because some of the basic mechanisms of sintering occur in various pyro-processing of fines lying in close quiescent contact, such as powdered metals practices, some types of pellet induration, firing of briquets, or other compacts, where the entire bed is brought to, and held at, the high reaction temperatures of sintering. Figure 1, The continuous sintering process as originally conceived consisted of intimately mixing carefully proportioned burdens, placing them in a comparatively thin, draft permeable layer, on a moving grate and igniting the surface while drawing sir through the bedded burden. The moving grate was advanced slowly as the line of burning fuel travelled from the surface to the bottom of the bed and no more fire zone could be seen.

Jan 1, 1973

By Owen Kingman

This paper discusses grade control of ore mined at Tennessee Copper Company. Mineral zoning and the influence of mineral zoning on production grade are discussed and illustrated. In order to make this most understandable we will first briefly examine the flow sheet at Tennessee Copper to indicate the path followed by the raw material toward its various products. Then we will discuss some of the characteristics of the ore, specifically the distribution or zoning of the minerals in the ore which cause some of the grade control problems. Finally we Will discuss same of the steps that are taken to combat these problems. The flow sheet is illustrated as plate 1. The mined ore is allied to obtain 3 usable products: Copper concentrate, iron concentrate and zinc concentrate. Copper is found in the mineral chalcopyrite, CuFeS2. The Copper concentrate from the mill contains about 20% copper. These concentrates are smelter in reverberatory furnace and Pierce-Smith converter to blister copper containing 99.2% copper. Some metal is cast into 360 lb. pigs and shipped to the refinery. Some is made into shot copper and used locally to make copper sulfate. Copper sulfate is marketed from Copperhill principally in fungicides.

Jan 1, 1960

By Wilbur I. Duvall

This paper discusses general principles of underground opening design based on the concept that with the necessary input data regarding the geology of a site, the physical properties of the rocks, the in situ stress field in the rock and the general geometry of the underground openings, the rock formation can be classified into six major categories which are useful for design purposes. Using simple theories for the criteria of failure for rock In compression and tension, general elastic theory for stress concentration around openings and In structures, beam theory for stability of roof rock, and elementary inelastic theory for creep phenomena, basic design techniques are outlined for the various rock classifications. The need for field evaluation of the theoretical design is stressed and some general techniques that should be used in these field evaluations are discussed. Where appropriate, the need for additional studies and research is noted.

Jan 1, 1977

By Geoffrey Purcell

The flotation response to amine collector of quartz and the feldspars microcline and albite, of the pyroxenes augite and spodumene, and of olivine can be, explained by a physical adsorption model. Flotation decreases in the order given above, and the different behavior of the three groups is attributed to structural variations of the silicates, With sulfonate collector both chemical action and physical adsorption play their part in producing hydrophobic surfaces, and flotation increases in the order given.

Jan 1, 1966

By Douglas E. Hansen

A current trend in blasting of large volumes of rock is to use increasingly larger diameter shot holes. The use of large diameter holes meant; correspondingly large explosive charges will be loaded and detonated, and, if special efforts are not made, will result in more damage and vibration beyond the intended blast area. With the rising awareness of environmental factors, vibration control becomes increasingly important. Equally important is the preservation of intended lines and grades, and in some cases by blasting with care, slopes can be safely steepended. In the past, vibration control was established to prevent damage to man-made structures. The quarry or open pit itself can be regarded as a structure composed of rock. Far too little attention has been given to the effects of blasting on rock walls. The primary purpose of blasting is to break rock. If the integrity of the rock has been destroyed beyond intended lines and grades, the excavation will be more costly than originally anticipated. The increased cost will not only be from in¬creased excavation due to overbreak, but also increased maintenance due to blast induced wall instabilities

Jan 1, 1976

By T. Malterer, R. Adams

Peat has unique physical, chemical and biological properties. These include high porosity and water retention, high absorption and adsorption properties, and high buffering capacity. In addition, peat is a rich medium for microorganism activity. Peat has traditionally been used for horticultural purposes. However, in recent years, peat is increasingly being used for waste- treatment purposes. This paper reviews North American literature on the use of peat for waste-treatment applications. The literature indicated that peat has potential for use in the treatment of municipal and on-site effluents, for the removal of low concentrations of heavy metals and for the adsorption of liquid and gaseous hydrocarbon pollutants.

Jan 1, 1997

By Erich U. Petersen, Robert B. Coleman, William J. Tafuri, Donald M. Hausen, P. R. Taylor, Douglas N. Halbe, D. W. Rodolff

The definition of refractory gold ores and concentrates, including mineralogical characteristics, is reviewed. The chemistry of roasting and process conditions such as feed size, temperature, and time are discussed. A typical metallurgical program for developing a roasting process scheme is presented. The application of various types of furnaces for roasting is described. Requirements for scrubbing off-gases to meet environmental air emission regulations, and general information regarding engineering design parameters for roasting are presented. Roasting is sound technology for processing refractory ores and concentrates, but it is essential that the metallurgy of each ore or concentrate is well defined before commercialization. A fluid-bed roaster is the preferred type of furnace for roasting. Environmental regulations for air emissions must be carefully addressed.

Jan 1, 1990

By Steve R. La Brooy

Techniques for dealing with copper-gold ores are reviewed. Cyanide has little selectivity of gold over copper, and depending on the reactivity of the copper minerals cut-off grades for gold recovery by direct cyanidation are generally below 0.5% copper for oxide ores and 1 % for sulfide ores. Non-cyanide gold leachants also tend to be reactive to copper. The cheapest option for sulfidic ores is to produce a flotation concentrate for smelting, while transition ores generally need a sulfidisation pre-treatment. The requirement for the concentrate to have a high enough copper grade to be acceptable to a smelter may compromise copper and gold recovery. This can lead to significant gold grades in the flotation tailing, and copper levels in the tailing that are too high for direct cyanidation to be able to recover the gold. Oxidised ores, flotation tailing or other material not amenable to flotation represent the greatest grey area for gold recovery. Copper removal by acid, alkaline or ferric pre-treatment is possible though not generally used. Cyanide pre-leaching to remove copper, followed by copper and cyanide recovery represents a potential option that has been installed at one Australian gold plant, where copper is recovered onto carbon, ahead of the slower leaching gold. Actual cyanide recovery depends on ore mineralogy, allowing for losses as cyanate, thiocyanate, carbonate and ferrocyanide. Alternative options for gold recovery following cyanide leaching include precipitation, ion exchange and solvent extraction of the gold. Ammonia-cyanide leaching may offer another option for more selective gold dissolution from flotation tailing and oxidised materials. A plant is currently under construction in Mauritania.

Jan 1, 1992

By Raja V. Ramani, Wilson Miola

The potential health effects of quartz-bearing airborne dust in mine and mill atmospheres point to the need for the quantification of quartz content in the source material for determining the source-sink relationships and for choosing applicable control measures. While a standard method exists from a regulatory point of view for the sampling of coal mine atmospheres for determining (i) respirable dust concentrations and (i) the amount of quartz in thesamples, there is no generally accepted standard method for quartz analysis in bulk samples of coal and host rocks. Generally, the bulk sample is reduced to a powder for producing quartz analysis samples. Extensive controls are necessary to ensure representativeness of the analysis samples when these are very minute fractions of the bulk samples. Since the amount of analysis sample is not limited, alternative methods for quartz analysis may also be tried. It is, however, necessary to adopt a procedure which will satisfy several statistical requirements to guarantee representativeness of the quartz analysis samples. In this paper, the important factors in the preparation of quartz analysis samples from the host rocks and bulk samples are discussed. The method developed to prepare the analysis samples is outlined. The results of application of the procedures are presented. The procedure developed for quartz analysis sample preparation is based on sound statistical foundations. The procedure has been validated for reproducibility and homogeneity.

Jan 1, 1991

By Deepak Malhotra

Comminution circuits in general account for fifty percent of capital and operating costs for a processing plant. Significant advances have been made in optimization of these circuits. One would expect a few circuits to be the favored designs for plants. Review of grinding circuits worldwide indicates that a variety of circuit designs are utilized for non-technical reasons. A brief review of circuits and reasons for their selection is given in this paper.

Jan 1, 1998

By M. Karmis

The algorithms for the mathematical modeling to predict productivity of underground room-and-pillar mining systems are well known and documented. These algorithms consider the time-varying relationships between mining equipment for a given geometty of operations as well as other constraints. This paper presents WebConSim, a newly developed, Web-based, user-friendly computer simulation tool for the Windows environment. The simulator is easily customized for use by field engineers, planning engineers and management and will help mine operators plan the optimum mining sequence for different mine geometrie and equipment layouts. Program output includes production data and equipment utilization indices, as well as time driven event chains that can be used for virtual reality presentations.

Jan 1, 2002

By W. Jacobi, K. Eisfeld

The primary objective of dosimetric modelling for the inhalation of radon daughters is the evaluation of the dose distribution and of the mean dose to sensitive cells or target tissues in the respiratory tract which are assumed to be responsible for the initiation of lung cancer. The results of such dosimetric models are influencing the practice of radiation protection in a twofold manner: Firstly, they enable us to identify appropriate operational quantities for air monitoring and for the surveillance of individual exposures to radon daughters. Secondly, they can be used to derive secondary and operational limits for these radionuclides from the basic dose limits. The dose to target tissues in the lung from inhaled radon daughters depends on various physical and biological parameters: The unattached fraction of daughter atoms, the AMAD of the carrier aerosol for attached atoms, the geometry of the respiratory airways, the breathing conditions, the parameters for the retention and translocation of daughter atoms in the different lung regions, and the location of the target cells or target tissues, respectively. Therefore, dosimetric modelling for radon daughters has to include a sensitivity analysis showing the influence of these parameters. To meet these objectives we have recently described in a comprehensive report an improved dosimetric model for the inhalation of 222Rn, 22ORn and their short lived daughters (Jacobi and Eisfeld, 1980). In the following this model is shortly described and the main results are summarized. DOSIMETRIC MODEL [Model Structure]. For the geometry of the bronchial airways the model A of Weibel (1963) was used. Each bronchial generation i (i =0.1 .... 16) was considered as a separate compartment i, for which the following transfer pathways for radon daughter atoms were taken into account (see fig. 1): (1) the uptake by deposition (deposition probability wi); (2) the translocation by ciliary clearance (rate constant [A]i); (3) the transfer to blood by diffusion through the bronchial epithelium (rate constant [A]b). To distinguish between attached (Index a) and free (index f) daughter atoms each bronchial generation was divided in two subcompartments (i.a and if) with a transfer rate constant [a]s (ia- if) characterizing the desorption or dissolution rate of attached atoms in the mucus fluid. Thus for daughter atoms primarily deposited in attached form the transfer to blood is a twostep process with the rate constants [a]s and [A]b which were assumed to be independent of the generation number i. [Deposition]. The deposition probabilities wi in each bronchial generation were calculated on the basis of the laminar diffusion model of Gormley et al. (1949); however the deposition in the upper airways was corrected for turbulent air flow, taking into account the results of our deposition experiments (Martin et al., 1972). Figure 2 shows the resulting deposition probabilities per unit surface area of the bronchial generations for nose breathing at a rate of 20 1/min. The values for attached daughter atoms refer to an AMAD of 0.2 - 0.3 µm ([O]g =3) for the carrier aerosol; the deposition values for free atoms were derived with a diffusion coefficient of 0.05 cm2/s, assuming a prefiltration of 50% in the naseopharyngeal region.

Jan 1, 1981

By Jess W. Smith

The carbonaceous Monkemeyer sandstone member of the Creede Formation on Bachelor Mountain hosts alteration and mineralization which contrasts with other silver deposits of the Amethyst system. More than 20 million ounces of silver are contained in disseminated mineralization in the volcaniclastic conglomerates and sandstones. Hydrothermal fluids entered the Creede Formation directly from the Amethyst fault system and mixed with flowing meteoric ground waters trapped beneath the Monkemeyer sandstone. Portions of the basal rocks of the Creede Formation were argillically altered by more dense acidic fluids generated by boiling. The carbonaceous base of the Monkemeyer and much of the conglomerates below were mineralized and well silicified. Deposition of the mineralization resulted from two processes: (1) reduction by carbon in the Monkemeyer, and (2) fluid mixing in the conglomerates. Monkemeyer mineralization is confined to the carbonaceous basal material and silver content is relatively consistent. Silver is contained in acanthite which is commonly associated with traces of galena, chalcocite, covellite and sphalerite. Fluid mixing and mineral deposition in the poorly sorted conglomerates was controlled by the highly variable porosity and permeability. Anomalous silver contents are dispersed throughout a large volume of conglomerates but zones of higher silver content reflect the crude layering of the conglomerates. Acanthite is finely disseminated in pore spaces and partly replaces some detrital magnetite. other metallic minerals are rare in the main zone of mineralization.

Jan 1, 2013

By Michael Robert Hodson

I. Introduction The free market cash price of aluminium in the third quarter of 1985 is approximately $1000/tonne, well below the short as well as the long run marginal costs of production. The current disparity between marginal costs and price, as well as the pattern of prices since their high level in 1980, has led many economists to question whether prices are governed by the 'fundamentals'. Prices, some would argue, are the result of speculation; and speculation is irrational, little influenced by the fundamentals of the industry. The object of this paper is first to examine the relation between the fundamentals and price. A number of simple models are formulated and some empirical evidence is given to show that prices are not very different from costs. There are good reasons why costs and prices have fallen since 1980. Second, the connection is drawn between the fundamentals and speculation. To do this the concept of 'rational expectations' is defined and applied to a model of the aluminium industry. Then speculation is introduced into the model and the characteristics of the solution are examined. The object is to discover the new factors that determine prices and the basic change in the nature of the solution that is caused by speculation. 2. Prices and the Simple Supply-Demand Model Consider a simple model of the aluminium industry. Demand, D, is determined by economic activity, A, given exogenously, and inversely by the price, P. Supply, Q, is determined by the inverse of the rnarginal cost curve, and so varies inversely with exogenous factor costs, C, and directly with price. Price is determined by the equality of supply and demand. Given the equilibrium level of demand, price in this model is equal to the rnarginal cost of producing the required level of demand, P = MC (Dl. Algebraically, [ ] How well does this simple model explain the change in prices during the last five years? Table I shows the LME cash price and the estimated marginal cost of producing consumption during the second quarters of 1980 through 1985. The figures in the table show that price and the marginal cost of supplying demand both fell between 1980 and 1982, rose in 1983 and by 1985 had fallen again. Only in 1984 is the direction of change different. And during the 1980 to 1985 period, marginal costs fell by approximately $560/tonne while the LME cash price fell by $678/tonne. There is a correspondence between the fundamentals of cost and price over most of the individual years and the period as a whole.

Jan 1, 1986

By Agne Rustan

Most of the mines in Sweden are metal ore mines in hard rock and none of these mines are classed gassy because there is no methane emission. The risk of methane explosions in Swedish mines is therefore very small. Since the 1960?s, in Swedish mines, there has been a change from electric and pneumatic loaders and transport machines to diesel. Today in almost all Swedish underground mines diesels are used. One of the most common complaint from the underground mine- workers is the exhaust gases from the diesel-vehicles. This is a strong motive for attempts to assure a more comfortable environment. Another motive for a better efficiency of ventilation under ground is the increasing cost of energy for fans and for heating the air during winter. For the largest mine in Sweden, the Kiirunavaara Mine, 36% of the energy for ventilation is used for preheating the air during the seven months when the temperature is below zero. The air quantities used for ventilation are large. In table 1 a comparison of the ratio between yearly produced ore and waste rock and installed fresh 'air capacity is shown. [ ]

Jan 1, 1980

By P. C. Kapur

The hierarchical relationship between three broad kinds of grinding models for a spatially homogeneous, linear, time-invariant batch grinding system are first established. Limiting and asymptotic arguments for arriving at approximate but simpler models are employed in all three cases. These parsimonious models -provide alternate and, in some respects, more incisive and convenient tools for the analyses of grinding processes and simulation of comminution circuits. In the discrete-size, discrete- time class of models, a reduced mill matrix is derived, which is seemingly adequate for those grinding circuits whose identification otherwise is difficult because of limitations on the quantity of data and its quality. In discrete-size, continuous-time types of models, parameter lumping has been employed for obtaining a G-H solution which is quite accurate and exceptionally useful for graphical display of data, model verification, and parameter estimation and simulation. In continuous-size, continuous-time models, a similarity transformation is used for solving the integrodifferential equation of grinding. This solution provides a unified framework for a number of apparently diverse empirical grinding phenomena such as self-preserving behavior of ground particle size distributions and energy laws.

Jan 1, 1987

By Safdar A. Gill

The technique of installing small diameter caissons (drilled piers) through soft clays and water bearing ganular soil is well established for constructing building foundations. Over the past few years, the method has been utilized for constructing a large number of shafts extending into rock for the Chicago's Deep Tunnel Project. This paper will discuss design considerations for obtaining the most economic ground support system, the impact of construction procedures on the support and lateral pressures for design. Construction procedures will be described along with performance of the shafts.

Jan 1, 1981

By M. J. Scoble

There is no straightforward and systematic method for adequately measuring blast damage in on-going mining operations. This paper considers various techniques available for the measurement of blast damage, making particular reference to recent underground hardrock mine studies. This paper concludes by indicating the importance of understanding and accounting for geology and emphasizes the need for a robust damage-audit procedure.

Jan 1, 1997

By W. S. Sadik

This paper presents the ventilation design for an underground testing facility in a salt medium. The underground workings consist of two-12 ft. (3.66 m) diameter watertight shafts and approximately 6000 ft. (1830 m) plus of drifting. These facilities are designed for the purpose of providing access for an in-situ testing of a salt horizon in which a variety of hazardous and non-hazardous materials could be temporarily stored or permanently deposited. The ventilation system includes a design basis for gassy mine conditions and provides for the option of bulk air cooling and heating.

Jan 1, 1988

By L. L. Newman, K. D. Ferguson

Traditional methods for mine waste management produces two waste streams and the construction of separate disposal facilities. Tailings impoundment design is usually controlled by physical stability problems. Alternatively. the waste rock offers high stability characteristics but hydraulic properties that create ideal conditions for oxidation. The problem of oxidation is significantly reduced for tailings due to a fine texture that augments water saturation. This paper introduces concepts for the co-disposal of tailings with waste rock and evaluates the physical behaviour of an integrated waste system. 'he potential benefits of co-disposal are shown for a typical mine such as Equity Silver.

Jan 1, 2000