Search Documents

By M. J. Blattman

The problem of measuring the amount of rock removed during a given time interval is faced by most milling operations. Many methods have been developed with varying degrees of success, dependent upon the mining method and the availability of usable data. The Rosebud Mine has been in production for nearly two years, employing several techniques to estimate monthly production from underground production stopes. The use of three-dimensional solids generated from survey data has greatly improved the reliability and confidence of monthly production reports. The authors will summarize the methodology currently being utilized at Rosebud.

Jan 1, 1999

By R. C. Bunge

Many minerals float best with fatty acids in the intermediate pH range. For example, fluorite, a semi soluble salt mineral, exhibits a maximum contact angle and a maximum flotation recovery in the pH range of 6-8 after conditioning in a palmitate solution (fig. 1). The maximum in flotation coincides roughly, as many researchers have observed, with the boundary of bulk precipitation of the fatty acid. According to fig. Z this boundary is in the above case of 5xl0-7 M palmitate approximately at pH 6.3. For assessing the phenomena occurring at the bulk precipitation boundary of fatty acids, the surface tensions of carboxylate solutions have been measured under various conditions. Fig. 3 shows the surface tension development of palmitate and myristate solutions of increasing concentration at pH 12. Also shown are the bulk precipitation edges (BPE) of the respective solid species that is stable under these conditions, that is the potassium acid soap, HKAZ. Both curves display a similar behavior. As the concentration of carboxylat,e increases, the surface tension decreases, until a minimum is reached at which the curves level off. The decrease of surface tension with increasing carboxylate concentration is generally taken to indicate the surface excess of the carboxylate ion. The point where the curve suddenly levels off has not yet been explained. While it is well known that the onset of micellization (CMC) may cause such an inflexion of the surface tension curve, this cannot be the case here because the position of this point depends, as shown in fig. 4 for palmitate, on pH (the CMC is generally independent of pH). We believe that this point indicates the precipitation of a colloidal acid soap (colloidal precipitation edge, CPE) before the bulk precipitation of this species sets in (BPE).

Jan 1, 1994

By R. D. Lord

This paper deals with the search for the best practical means of storing sulphide bearing tailings, where there is no residual excess of carbonate material. It is the common experience that the sulphide content decomposes, with the aid of bacterial action, and the resulting sulphuric acid escapes, along with any heavy metal solutes, through embankments that are usually porous to some degree. The problem is typified in the tailings of the uranium operations of Elliot Lake, Ontario, where mining started some 20 years ago. The approach to tailings disposal paralleled the practice for other hydrometallurgical plants treating gold and base metal ores. Impoundment areas were designed to retain solids, and a clear and neutral overflow was considered satisfactory practice. Now experience has shown that these areas, some idle for over a dozen years, release acids, in seepage and overflows, to an unacceptable degree. To protect natural water courses neutralizing plants are operated wherever required. Lime slurry is fed continuously into the tailings outflows in a quantity sufficient to raise the pH to 8.5 and precipitate heavy metals that may be in solution. The objection to this procedure is that the plants will require servicing indefinitely, unless a better remedy is found.

Jan 1, 1975

By Ki Chun

Optimizing ore processing requires a thorough understanding of not only the process itself but the economic constraints which influence business decisions. No single modeling technique is able to model all the different processes running in today's mines. The solution then is to use a number of different model­ing techniques, each competing with the others to best correlate the data. Among these modeling techniques are: Neural Networks, Genetic Algorithms, Fuzzy Logic, Crisp Logic, Statistics, First Principal Models, and System Identification models. Once a model has captured the behavior of the process, a numerical optimization determines the optimal operating point and set point parameters. A single step is then taken in the direc­tion of the optimal location by changing all the process parame­ters to the setting recommended by the optimization system. As the process begins to re-stabilize, the models are updated, the new optimal determined and another step is taken in the direction of the optimum. Through the use of multiple competing models integrated into a numerical optimization the process can achieve the optimal running condition even if the ambient conditions fluctuate dynamically.

Jan 1, 1998

In late 1993, Inco Ltd. completed a $600-million environmental improvement project at its Sudbury, Ontario operations -the largest single environmental project ever undertaken by a Canadian corporation. Efficient new facilities and innovative technologies installed during the course of the project have also significantly improved Inco's productivity and competitiveness. In early May 1994, a panel of 18 Inco authors contributed to a Technical Forum, "Environmental Programs at Sudbury," presented at the 96th Annual General Meeting of the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) in Toronto. Their papers have been published in CIM's Toronto `94 Proceedings Volume, pp. 62-77. The following report draws primarily on discussions of Inco's milling and smelting operations published in the Proceedings Volume. The Proceedings Volume also includes papers on the acid and oxygen plants and on engineering, construction and commissioning of the project. The 222-page Proceedings Volume is available from CIM, $C27 plus shipping. To order, contact: V. Ward, CIM, Xerox Tower, 1210-3400 de Maisonneuve Blvd W, Montreal, Quebec, Canada H3Z 3B8; phone 514-939-2710, fax 514-939-2714. Lane White, Publisher.

Jan 1, 1994

By Hang Yang, Linneas W. Laage

A major concern of mine fires is the heat generated ventilation disturbances which can move products of combustion (POC) through unexpected passageways. Fire emergency planning requires simulation of the interaction of the fire and ventilation system to predict the state of the ventilation system and the subsequent distribution of temperatures and POC. Several computer models were developed by the U.S. Bureau of Mines (USBM) to perform this simulation. The most recent, MFIRE, simulates a mine's ventilation system and its response to altered ventilation parameters such as the development of new mine workings or changes in ventilation control structures, external influence such as varying outside temperatures, and internal influences such as fires. Extensive output allows quantitative analysis of the effects of the proposed alteration to the ventilation system. This paper describes recent USBM research to validate MFIRE's calculation of temperature distribution in an airway due to a mine fire, as temperatures are the most significant source of ventilation disturbances. Fire tests were conducted at the Waldo Mine near Magdalena, NM. From these experiments, temperature profiles were developed as functions of time and distance from the fire and compared with simulations from MFIRE.

Jan 1, 1995

By James P. Dorian

istorical records suggest that the gathering of geologic information in China began more than 2,000 years ago. Modern-day geological work in the nation started in the early part of this century but it progressed rather slowly. Before the founding of the People's Republic of China (PRC), there were only 800 people engaged in geological work and only 200 trained geologists among them. According to Minerals and Mining in China, many accomplishments were achieved within China's mining industry during the period of years between 1949, the founding of modern China, and 1997. These include: ? The number of types of minerals with verified reserves increased from 18 (pre-Liberation) to 162 (today). ? Mineral deposit localities grew from 5,123 (pre-Liberation) to nearly 200,000 (today). Of these 200,000 localities, more than three-quarters have verified mineral reserves. ? Minerals extraction and processing contribute to 31 % of the total industrial output value of China (today). ? Regional geological maps at a scale of 1:1,000,000 covering the entire country have been completed, while regional geological and hydrogeological maps at a scale of 1:200,000 covering two-thirds of the country have also been finished (today). ? Before 1949, China was regarded as an oil-poor country. Since the 1950s, China has developed an extensive petrochemical industry. It is largely government-owned except for a limited number of joint ventures. The central government maintains active control over China's most productive fields, including the Daqing field in the Songliao Basin of northeastern China and the Shengli and Liaohe fields in the Bohai Basin of northeastern China. ? Employment in the minerals industry engaged in geological exploration increased from 800 (pre-Liberation) to 1 million (early this decade). The new report provides an overview of the current political and economic situation in China and discusses how this affects the minerals industry. China is in transition between a socialist planned economy and a market economy. This makes it difficult for non-Chinese to keep track of developments. Minerals and Mining in China is divided into 14 chapters that contain detailed statistics, including data on the geographical location and extent of known mineral reserves, production rates, local technical personnel, imports and exports. The report reveals which companies are already active in the area by profiling 50 major investment projects in China's metals and minerals industry. According to its author, China possesses one of the world's largest mining industries, ranking among the leading producers of several metallic and nonmetallic resources. The Chinese mining industry is extraordinarily complex. It has evolved into an overwhelmingly large bureaucracy that was, until the 1980s, shrouded from and misunderstood by the international community. To date, more than 160 types of minerals have been discovered in China. But a significant portion of the minerals and energy base remains largely unidentified and evaluated. And despite China's large reserves of mineral resources, with a population of more than 1.2 billion people, the country ranks among the lowest in the world in terms of proven reserves per capita. In addition, mining recovery rates in China average about 50%, significantly

Jan 1, 1999

By William G. Davenport, Eric H. Partelpoeg

Direct smelting of copper in a single vessel has long been the extractive metallurgist's dream. Such a process offers the important advantages of (i) maximum use of the energy available from oxidizing the sulphur and iron of the concentrate; (ii) restriction of SO2 emissions to a single constant-strength source; (iii) minimum materials handling and (iv) elimination of at least one process step. Extensive developmental work was carried out in the 1960's and 1970's to implement such single-step processes. Some of the processes reached the prototype stage and it appeared that copper smelting technology was on the threshold of a new, efficient, minimum-pollution era. Since that time, however, the forward thrust has slowed and single-step smelting is still a process of the future. The paper describes in detail the potential advantages of single-step smelting; its history and current status; and the reasons why it has not been adopted industrially. It concludes that the potential benefits of single-step smelting are powerful and that many of the difficulties encountered in the 1970's will be overcome in the 1980's.

Jan 1, 1985

By Robin J. Batterham, Stephen H. Algie

It is often stated that innovation is central to the economic survival of mining and mineral processing in the face of global competition, and yet technology is often far from a core strategy in our industry - hence the concerns that are often voiced about the apparent slow rate at which new technology is applied. Much of the discussion stems from a lack of understanding of the role of technology in innovation, and of the role of R&D within the innovation process. To a large extent this has all been said, however, the messages are clear and deserve repetition. This paper expresses the personal views of the authors, based on experience in government-funded (CSIRO and universities) research, and in CRA Ltd, a large mining and mineral processing company. Further than this, it explains how our own development unit within the CRA Group has come to see its key roles as including the transfer of technology, and the training of technologists to move into the operating business units. We conclude that these critical tasks are the keys to creating the environment that will allow us to maximise the contribution of technology.

Jan 1, 1995

By Edwin H. Bentzen, Immo H. Redeker

Important industrial minerals are separated and concentrated by froth flotation by industry today. The following descriptions are presented as an overview of the methods employed to separate and recover a few of these industrial minerals. The minerals described in this section of the book are not, by any means, the only important minerals treated by froth flotation. Other minerals, such as calcite, kaolin, wollastonite, rare earths and vermiculite were not included, primarily due to the confidential nature of the information held by the Minerals Research Laboratory and the Colorado School of Mines Research Institute. Flotation of nonmetallic minerals is sometimes viewed as alchemy. However, the art is, in reality, based on sound chemistry, experience and a little luck in the treatment of new ores. In the flotation of nonmetallic minerals, as opposed to base metal sulfides, highly specific treatment conditions are required to accomplish separations. The presentation of the treatment of each of the minerals described was outlined as follows: DEPOSITS PROCESSING SPECIFICATIONS FLOWSHEETS (in some cases) A presentation of the factors, often critical, which must be carefully investigated to accomplish successful flotation of nonmetallic minerals is presented in the section on Sulfonate Collectors, elsewhere in this volume.

Jan 1, 1986

By William J. Miles

From a historical perspective, bentonite is the common rock term for various uses and applications. Its name originates from water-based muds near Fort Benton used for lubrication of wagon wheels during the 19th century migration to western territories (which are presently part of the United States) when the pioneers ran out of axle grease. From a clay mineralogy perspective, bentonite is composed primarily of montmorillonite, an expandable magnesium aluminum silicate clay mineral. When magnesium occupies an octahedral structural site that usually contains an aluminum atom, a negative charge is created. In order to neutralize negative charges, cations are drawn to the interlayer surfaces between clay mineral sheet structures. Modem applications for bentonite depend on the sodium or calcium cation populations and other characteristics of the clay mineral. When sodium is the dominant cation, the material is called sodium bentonite, also known as swelling bentonite, western bentonite or Wyoming bentonite. When calcium or magnesium is the dominant cation, the material is called calcium bentonite, also known as non-swelling bentonite w southern bentonite.

Jan 1, 2012

By H. Dho

Two aromatic-type chelating agents, 1,10 phenanthroline (phen) and 8-quinolinol (quin), were tested as specific depressants for magnetite in the cationic silica flotation of magnetic taconite concentrates. Micro and batch flotation tests, along with zeta potential and adsorption measurements were used. In the presence of a cationic collector, dodecylammonium chloride (DAC), the Fe/phen surface chelate electro-statically repelled DAC, and magnetite was depressed. The negatively charged Fe(quin)2(OH)2-on the magnetite surface attracted the cationic collector and made magnetite floatable.

Jan 1, 1995

By Derek J. Barratt

The specification of the prime mover of an autogenous/semi-autogenous mill involves an analysis of the likely operating conditions within the mill and the choice of a nominal operating speed. For variable speed mills, the operating range for mill speed has to be defined so that mill power/torque requirement can be matched by the motor power/torque capability. This paper will describe how this relationship can be influenced by ore grindability.

Jan 1, 1993

By C. S. Harman, C. A. Enright, J. F. Brune

"The mining environment presents challenging and complex situations for the application of medical care. The combination of remote locations, difficult access and longer response times may create an increase in morbidity and mortality in the event of serious accidents. The U.S Mine Safety and Health Administration (MSHA) has only minimal requirements of first aid training for mine workers. For mine rescue team members, MSHA requires medical training at the Emergency Medical Responder (EMR) level, as only prescribed by mine rescue contest rules. This paper examines, based on mine accident statistical information, whether a higher level of medical training, for example at the Emergency Medical Technician (EMT) or at the Advanced Life Support (ALS) level can better address injuries most commonly disabling or leading to the death of miners in the United States. BACKGROUND Prehospital emergency medical care for the sick and injured has evolved considerably from first inception. Ambulances used to be staffed by persons with little training and equipment and prehospital care was focused largely on the rapid transport of the injured person to a hospital and. The modern prehospital care model was initially developed in military applications, where medics were responsible for some treatment on the battlefield and rapid transport to the care of a physician. In 1965, the National Academy of Sciences and National Research Council Committees on Trauma and Shock published Accidental Death and Disability: The Neglected Disease of Modern Society (National Research Council Committees on Trauma and Shock, 1966). This white paper laid out the consequences of the insufficiency of the Emergency Medical System (EMS) in the United States at that time. According to this paper, in 1965, 107,000 people were killed from accidental injury, with another 400,000 injured with permanent disability. The authors estimated that approximately 50% of ambulance services were provided by local morticians that were not capable of rendering advanced life support. The paper states that, based on experiences in the Vietnam war, seriously wounded soldiers had a better chance of survival in the battle field compared to traffic accident victims with similar traumatic injuries because the military was capable of providing first aid and efficient transportation to emergency care facilities. The white paper states that death rates from battle injuries declined significantly from 8% in World War I to 2% in Vietnam. The publication of this white paper is credited for the broad evolution and rapid advance of the civilian EMS system after 1965. It eventually lead to the creation of the National Highway Transportation Safety Administration (NHTSA) National Standard Curricula (NSC) for emergency medical care in 1985. Training, and therefore required skill and knowledge for prehospital emergency care has continued to grow to reach the current standard."

Jan 1, 2016

By C. Ottergren

A process does not have higher capacity than what can pass through its bottleneck. Acknowledging this, and with the goal to optimize production at a minimum investment, one can use existing equipment, modify the process flow and make a few strategic capital investments. Automatic setting regulation is a technology that allows balanced crusher performance matching minute changes in feed material characteristics. The system makes it possible to utilize the crushers fully at all times. It also continuously and completely compensates for manganese liner wear.

Jan 1, 1999

By S. Eugene Mills

Twenty-five years ago, when I began my sales life marketing minerals, there was little or no contact between sales people and production people. In those days, it was not uncommon for me, as a salesman, to learn of production problems existing in my company from my customers. Today, in my opinion, any successful mining company must keep production people fully aware of circumstances that effect service to the users of the product. Basically, feldspar is presently consumed by the glass and pottery industries the same as 100 years ago. The consuming public little realizes the origin of so many things they use daily and take for granted. Feldspar is utilized in the glass that contains our Coca-Cola, Pepsi, wines, liqueurs, beer and the assorted gob¬lets from which we drink these lovely brews, the industrial glass upon which all industry depends, the bathroom plumbing fixtures that make life so different from the days of the out-house, the beautiful and durable china we enjoy at mealtime. The electricity we use requires insulators that demand feldspar. In our home ap¬pliances, automobiles, toys and airplanes, we find feldspar. I could go on and on, hopefully soliciting your help in making our taxpaying and non-taxpaying fellow man aware of the burdens he may acquire when unthinking, over-enthusiastic environmentalists foist unnecessary hardships upon the mining industry. Feldspar is marketed primarily sized from 20 mesh to 325 mesh. The glass industry requires feldspar ground 20 mesh to 40 mesh size; the pottery industry requires material from 150 mesh to 325 mesh size. One large glass plant may require up to 100 tons per day and more, whereas a small plant may use less than 5 tons per year. A large pottery plant may require as much as 50 tons per day, a small potter only 500 lbs. per year. The feldspar

Jan 1, 1977

By B. J. Arnold

Utility coal specifications usually contain a requirement for a maximum moisture content in order to prevent coal handling problems and to minimize evaporative losses in the boiler. As most coal cleaning processes are water-based, dewatering and sometimes thermal drying steps are required to meet moisture specifications. Screens are often used for dewatering, with centrifuges and filters used to further reduce moisture in many cases. Algorithms to predict the performance of commercial dewatering devices were developed for the Coal Cleaning Simulator running under Aspen Plus? during a project sponsored by the U.S. Department of Energy and the Electric Power Research Institute. These algorithms include calculations for size degradation in the devices and fines loss to effluents, where appropriate, and a calculation for moisture content of the product based on particle size and specific gravity distribution. This paper discusses the algorithm for coarse and fine coal centrifuges and gives comparisons between predicted moisture and solids loss and published moisture and solids loss values for various particle size ranges.

Jan 1, 1996

By R. W. Smith, J. Dubel, M. Misra

The bacterium Mycobacterium phlei is highly hydrophobic and negatively charged. It has specificity for selective adhesion to fine coal particles, mainly due to hydrophobic interaction. However, it does not attach to pyrite and ash forming minerals present in the coal matrix. Results have shown that this bacterium is an excellent flocculant for fine coal. Not only, are the coal particles visibly aggregated, but the optical micrograph has shown that the coal particles are held in the aggregate by adhesion and bacterial bridging. With Mycobacterium phlei, the flocculation characteristic of coal is markedly different from that usually observed with synthetic polymeric flocculants. In particular, the entwining characteristics of the long chain molecules of synthetic flocculants are absent in the case of Mycobacterium phlei. Since the hydrophobic interactions between the adhering particles are of greater importance in the formation of particle aggregation, the flocculation process is very selective.

Jan 1, 1994

By D. A. Swanson

Predicting when and at what rate seepage will occur from waste-rock facilities is becoming an integral part of permitting and closure at mines situated in dry climates. Such predictions require development of a conceptual framework that accurately describes how water will percolate through a waste-rock facility. Also needed is a detailed hydrological characterization of the waste-rock facility, including measurement of the hydraulic properties of the waste rock and any potential cover materials. This paper presents a conceptual framework describing unsaturated water flow in a waste-rock facility and describes methods for characterizing the hydrology of a waste-rock facility in a dry climate. The methods are designed to collect site-specific data to support accurate and defensible predictions of long-term seepage rates.

Jan 1, 1998

By Gerhardt A. Bennewitz

The mechanism shown here (Fig. 1) may not be all that it appears to be. To many of you it may look like a hopper car, a thing of mobility, in which you would ship coal, ores, limestone, or other bulk materials. It is approximately 50 feet long, 12 feet high, and can be placed on tracks which are on approximate 14 foot centers. But far too often in the past, and all too often today, this mechanism has been made to serve as an immobile storage box, with its primary role -- the transportation of products, seemingly incidental to the storage function. Our engineering training teaches us to conserve resources, despite some of the popular and misconceived philosophies being advanced these days. Those of you who work for companies with traffic departments know that they are always striving to reduce the price which is paid to move your mine products. Today, let's consider and analyze the ways in which the cost of transporting your mine products might be reduced, based on particular reference to coal. Bear in mind that in this context, cost and price are not necessarily synonymous. Until a few years ago, most coal and other bulk materials handled by railroads moved under standard tariff rules. These rules, which still exist today, provided transportation vehicles (railroad cars) for extended periods at no added price to the shipper or receiver. "Normal" free time rules would permit a car to be held for a maximum of 48 hours without charge; however, in the case of coal, there is a rule which, subject to liberal rules as to the

Jan 1, 1972