Search Documents

A portable electronic instrument was developed which will measure change of longitudinal wave velocity with change of uniaxial stress in rock columns. The instrument is a solid-state device powered by nickel-cadmium batteries. It uses a probe of two piezo-electric crystals spaced inches apart to send and receive a pulse through a stressed rock. A one-inch cathode ray oscilloscope visually displays the longitudinal wave. A reference chart is used to find the stress. Laboratory results have indicated that the average stress on a sandstone column can be found to within 35 psi. The feasibility of using this instrument to determine stresses in mine pillars is to be studied. The instrument may be used to investigate physical properties of rock.

Jan 1, 1970

By J. Lorosch

Improvement of current leaching technology was found necessary when processing ores which are more difficult to leach because they generate highly viscous, air-rejective pulps. Cyanidation of these pulps has to run at low oxygen concentrations if the conventional aeration technique with compressed air is used. Since the dissolution rate of precious metals mainly depends on the concentration of dissolved oxygen in the pulp [1, 4, 5], the kinetics of the gold extraction become slow in such cases, which in turn often leads to a significant decrease in the overall gold output within the conventional leaching time of up to 48 hours.

Jan 1, 1988

Slurry technology developed for the marine transport of mineral commodities has been increasingly applied to on-shore slurry transport systems. Reclaim of mineral concentrates, sand tailings for mine backfill and various industrial minerals from storage tanks or ponds normally require a slurry of high density at constant flow rates to improve process performance and to reduce handling costs. An efficient system must accomplish this at minimum capital costs with maximum reliability. Continuing improvements in equipment design to improve repulping efficiency and their application are discussed.

Jan 1, 1986

By Helmut Goehring

Surface mining has been used primarily where deposits of minerals were exposed or close to the surface. Surface mining can, therefore, be considered the oldest branch of mining. As the most accessible deposits became uneconomical because of the lack of suitable high capacity conveying systems, deep mining took its place. Only in the twentieth century was this trend reversed as high capacity production and conveying systems were developed. This rapid development was triggered by the steadily increasing demand for raw materials and fossil fuels, as well as by the ever increasing ratio between overburden and deposits.

Jan 1, 1982

By R. E. Driscoll

The exploration, geologist of necessity has to have a wide working knowledge of many specialties other than hiw own, First he has to use his own technical background to find a deposit,, of a mineral that is of interest, Once found, his problems are Just beginning, He then has to assume the role of an economist, an accountant, a mining engineer, a chemist, a metallurgist,, a salesman and what-have you, In the economic field, he must determine the marketability of either the ore or the refined mineral. He must gauge the supply and demand for the particular mineral he is interested in and make his best guess as to ultimate cash flow from a deposit over the estimated life of said deposit, He must then assume the role of a mining man and estimate cost of recovery, including an, evaluation of the most economic mining method, cost of supplies and labor, and again estimate a net cash flow. He must then determine amenability of ore to economic metallurgical methods, he must determine the legal status of the property involved and, after analysis of the specific situation, determine the best approach to a deal, After all of this he must sell it to the people who will put up the money and then put his deal together and sell it to the people who own the minerals, if that be necessary. Then he has to sit back, with crossed fingers and crossed legs wondering for some months, and in many cases even years, whether or not he is right. The expenditures required to open up a mine in this day of wild inflation are such that he has to be right, and the responsibilities are awesome.

Jan 1, 1958

By Joao B. Cardoso

This paper describes a two-stage reverse flotation method developed at the Mineral Resources Institute (MRII, University of Alabama, for Kerr-McGee Corporation (KMC), to separate the trona (Na2CO3 ? NaHCO3 ? 2H2O) from a saline deposit containing halite, borax, minor salts, and water insoluble materials. In the first stage, trona is depressed with Quebracho, and the insoluble gangue is floated with fatty acid. In the second stage, trona is floated with cresylic acid. The flotation concentrates contained better than 90% trona with insolubles ranging between 1 and 2%. Although the trona recoveries were low, optimization and middlings recycled in a continuous circuit could substantially increase the value.

Jan 1, 1989

By Walfrid Been

There are no particular nor unique features of iron mining that are not shared in some degree by all mining ventures everywhere. There are, however, at least three problems that have acquired a special emphasis from a unique cause. That cause is the embarrassment of riches under which the industry is suffering. The most obvious' feature of iron mining today is the copious abundance of usable ore and its almost universal distribution over the face of the earth. By the term "usable ore" is meant ore that is amenable to reduction by the usual and conventional processes. Amidst this plenty, three problems become acutely emphasized: 1. The geographic location that will provide a mine with the best market opportunity. 2. The size of the orebody that will be required to' return the preproduction investment. 3. The geometry and configuration of the orebody that will permit quality control measures to be effectively executed.

Jan 1, 1964

By Dennis W. Leonard

Let us begin our discussion by looking at historical and current levels of sales of both natural and synthetic zeolites on a world-wide basis. Due to the understandable reluctance of some companies to disclose sales data, some estimation has been necessary regarding the tonnages and values shown in Table 1. We are confident, however, that they are within acceptable limits, especially the numbers referring to natural zeolite.

Jan 1, 1979

By J. David Lowell

This paper describes the geology of the Kalamazoo copper orebody discovered in the course of an exploration project carried out by Quintana Minerals Corporation under the author's direction in an area immediately southwest of the San Manuel mine, Pinal County, Arizona. In the period 1943-1947, exploration projects were carried out in the San Manuel area by the U.S. Bureau of Mines and Magma Copper Company which resulted in the development of the San Manuel underground block-cave mine which is now in production at a rate of 41, 000 tons per day. Mining claims covering the area immediately west of the San Manuel orebody were staked in 1946 by Frank F. Salas, R. A. Buzan, H. G. Buzan, and W. C. Buzan of Mammoth, Arizona. These claims were optioned to Martha Purcell in 1946, and in the period of 1947-1958 seven churn drill holes ranging in depth from 1,400 to 2,950 feet were drilled by Mrs. Purcell. These holes did not intersect ore and no further deep exploration was attempted prior to the Quintana Minerals project which began in August, 1965, and which is described in this report. The Kalamazoo deposit is in Sections 3, 4, 9, and 10, T 9 S, R 16 E, Pinal County, Arizona, and it is reached by driving seven miles east from Oracle, Arizona (Figure 1) . The writer is indebted to Corbin J. Robertson and Ronald B. Thompson who participated in the exploration planning of this project and to a number of other individuals who contributed to its execution and management. Petrographic work by J. M. Guilbert was used as a basis for rock and alteration classifications.

Jan 1, 1968

By Harry Teicher

The subject of Specialty Silica Products could encompass a broad range of materials, some of which would be familiar to members of the Society of Mining Engineers. With the concurrence of your chairman, I have chosen to limit my remarks to synthetic materials, not including such siliceous materials as diatomaceous earth, asbestos, quartz and clays. For purposes of discussion, I have classified Specialty Silica Products into two groups -- powders and liquids -- which I will discuss in that order and which are categorized in Figure 1. The synthetic silica powders are amorphous to x-rays and are manufactured by various processes resulting in products of a wide range of physical and chemical properties, as well as functional performance and applications. Applications or functional properties are generally dependent upon such physical properties as micron-sized particles exhibiting large surface areas per unit weight and low apparent bulk density. Their presence in various systems modify surface properties. As summarized in Figure 2, they act as viscosity modifiers, flow conditioning agents, anti-slip agents, anti-blocking agents, flatting agents in surface coatings, reinforcing agents in polymers such as silicone rubber and numerous other applications. Although the various types of silicas exhibit various levels of functional performance in these end uses, they are not usually equally effective as direct replacements and I will briefly discuss the various types of materials.

Jan 1, 1974

By Bryan A. Bartley

High intensity, autogenous grinding has been developed in the hard rock, quarry industry and is finding wide application in mineral processing. The autogenous vertical shaft impactor is described and action within the machine is illustrated. This machine is compared with the cascade mill, in the three characteristics of impact, inter-particle rubbing and nipping, of which impact is the most important. There is a seven fold increase in impact level over that of the cascade mill. The autogenous impactor has characteristics of crushing and grinding, preferential crushing, abrasion resistance and drying. These are illustrated by examples of industrial applications, where the machine is now used and range from abrasives, such as Carborundum to phosphate rock.

Jan 1, 1998

By J. C. Irvine

Meramec Mining Company is a joint venture by Bethlehem Steel Corp. and St. Joe Minerals Corp. which mines and pelletizes iron ore at the Pea Ridge Mine. The Pea Ridge property is located near Sullivan, Missouri, about 70 miles southwest of St. Louis. The orebody was delineated in the mid-1950's by St. Joe during a lead exploration program. The first test holes drilled on the Pea Ridge magnetic anomaly revealed the presence of a large magnetite deposit; further drilling in 1956 and 1957 confirmed that the orebody was mineable, Meramec Mining Co. was incorporated in 1957 and shaft sinking began late in the year. Production commenced in April 1964. The orebody is overlain by about 1300 feet of flat-bedded sediments. It is tabular, about 2600 feet long and up to 600 feet thick. It dips about 80° and is of unknown depth. The ore is mainly high grade magnetite with small zones of specular hematite. The wall rock is a Precambrian rhyolite porphyry. The mine was initially started with five major levels on 150 foot intervals. Crosscuts were driven across the orebody on 190 foot centers. Banks of scopes were mined between the crosscuts by a modified shrinkage stoping method. This was done by undercutting a 40 foot wide by 150 foot long block and blasting horizontal "lifts" drilled on 5 foot intervals. A 65 foot still was left between levels which contained the slushing drift, fingers, crown pillar, and adequate thickness for support. By 1971 a ?lattice? of pillars had been left and mining had progressed to the point that an orderly pillar recovery program was necessary.

Jan 1, 1976

By John Lovering

The Afton property is located 180 air miles East-Northeast of Vancouver and nine miles West of Kamloops, a city of 60,000 people, in South Central British Columbia, Canada. The mine is adjacent to the Trans-Canada Highway at an elevation of 2,200 feet above sea level. The orebody is a porphyry, copper deposit that has undergone supergene alteration. The-major economic minerals in the supergene zone are native copper and chalcocite with chalcopyrite and bornite in the hypergene areas. The grade is one percent with an overall copper distribution: 70% native, 25% chalcocite and 5% chalcopyrite with bornite and covellite. The ore also contains important, but variable amounts of gold and silver.

Jan 1, 1985

By Dale D. Teeters

Today, I would like to talk about ways to maximize the efficiency of surface coal operations. I doubt I will present any startling new ideas, but my comments may, hopefully, stimulate some conversation today and later back at your own operations. Strip mining is a very old technique used by ancient societies. Only with the coming of the machine age in the early twentieth century did we attempt to increase the magnitude of our operations. The industry, as we know it today, really only got started in the early 1900s with the advent of steam shovels. In the first portion of this presentation, I will attempt to show that we have, in many cases, not changed the basics of strip mining, only the scale. In doing so, quite often we have complicated the operations to the point of being unmanageable and unprofitable.

Jan 1, 1981

By A. F. Ogg

The installed world steel capacity remains 20% above the present world steel demand. Energy costs have risen enormously in recent years, as illustrated in Figures 1 and 2. The role of the sinter plant is becoming more exacting as it becomes vital to minimize energy consumption. Continuous grate sintering, although pioneered in the United States, has always been the second grade burden preparation route, due to the predominance of easily up- graded ores which were more readily agglomerated by pelletizing. To achieve blast furnace performance up to best world standards, sinter of consistent high quality must be produced with virtually no atmospheric pollution. The plants must be capable of achieving this demanding level of quality whilst utilizing high proportions of revert materials, iron ore concentrates and fluxes . However, with the present difficult economic climate in the iron and steel industry, the economic production of sinter and ultimately steel is becoming increasingly important. The iron and steel industry is looking closely at costs and is identifying the need for sinter plants that will cope with a wide range of sintering materials to give the cheapest blend at varying output levels dependent upon demand. In order to meet these requirements, sinter plant builders are designing plants with particular attention on flexibility.

Jan 1, 1980

By Ellis J. Brien, O&apos

This afternoon I would like to talk to you about coal, its defi- nition, its constituents, its associated minerals and present and future coal preparation techniques. This discussion will be an attempt at presenting sufficient coal preparation and associated fundamentals to enable you to understand "deep cleaning", a more advanced beneficiation process which will be commercially practiced in the near future.

Jan 1, 1976

By D. G., Bosse&apos

Equipment choices for ultrafine grinding encompass several different types of dry and wet size-reduction devices. These need to be put into functional perspective for systematic analysis of capabilities and limitations versus processing requirements of the materials to be satisfactorily ground. Particle strengths plus maximum and average sizes are the primary variables controlling grinding action requirements and equipment options for efficient processing. These are fairly well understood and provide the starting point for decisions. Particle space requirements under dynamic processing conditions vary with particle shapes and size-distributions by as much as 30X. This additional major variable is not widely appreciated and does need adequate description to provide a firm basis for selecting processing compositions and procedures.

Jan 1, 1983

By M. P. Corriveau

This is the case history of how two nearby plants in Southwest Virginia solved their water clarification problems. While the solutions should not be considered applicable industry-wide, the methods used in arriving at the answers deserve consideration. When Clinchfield's Moss No. 2 Preparation Plant, the first ever built in Tiller Seam coal, was started in the fall of 1956, the clays in the raw coal soon posed a flocculation problem, Laboratory sedimentation tests were initiated; and as a result, lime was adopted as the flocculant for the clays, With lime, a pH of 11.2 was required. As the plant tonnage increased, it became evident that the amount of coal fines produced in the mining and preparation was greater than had been estimated and that the 90-foot thickener was inadequate in providing sufficient settling time to effect a clarified overflow for reuse. Testing showed that Separan 26105 (NP10)1/, when used with lime, was the most satisfactory coal flocculant available,

Jan 1, 1960

By L. Gutierrez, S. Gering, C. Calderon-Arteaga

"INTRODUCTION Drill and blast (DnB) represents the most important, and sometimes the most costly processes in a mine.. The cost of drilling and blasting operations greatly contributes to the “high cost trends of the overall mining operations” (Afum B. O. and Temeng V. A. 2015). The use of available information to improve the DnB processes can be the difference between a highly expensive process and an optimized one. Mining operations have access to several types of data sets and key information from a wide variety of different systems. This information is normally used to improve, evaluate and apply processes for drilling and blasting. This may include different types of data from the different stages of the process (before, during, and after the drilling and blasting operations), such as hole locations (planned and actual), penetration rates, drill operators, fragmentation (expected and resulting), explosive (design and usage), geology, vibration, and others. This information can be used on its own or combined for further analysis to reduce costs, improve safety, and evaluate results. Fortunately, due to advances in mining software, drill and blast engineers can exploit this data and create reports to evaluate results and improve the DnB process. However, as users start combining information from multiple datasets and establishing standard operating procedures for reporting this data across multiple sites, it becomes valuable to create auditable, automated, and sustainable processes for handling the information. In many cases the task of aggregating and standardizing the data formats has already been completed and is available to consumers via the Enterprise Data Warehouse (EDW). A data warehouse team extracts data from the source systems and transforms it so that it is meaningful for decision support (Barbara H. Wixom, Hugh J. Watson, 2007). Our initial implementation plan for the DnB solution included using data stored at the sites; however we learned early on in the process that much of the work for aggregating and supplying the required data was already completed. The goal for this case study is two-fold: to show how information can be used to make decisions and improve processes, highlighting the value of using an EDW for managing Drill&Blast information; and to discuss how technical challenges encountered during the implementations were resolved. This paper is targeted at users that want to better manage their DnB data or try to set up standardized workflows for using this information. This case study will discuss the process of implementing a DnB workflow at multiple sites within Freeport McMoRan Inc (FMI) using both data at the sites and information available using the EDW. The paper will begin with an overview of the project. The discussion will then describe how DnB processes were used to set up daily workflows in order to provide information for evaluating process and making decisions. The final section will discuss some of the technical challenges and how they were solved, as well as possible next steps for further improving the workflow."

Jan 1, 2017

By L. C. Bartel

Geologic features such as structure (faults, folds, fractures, etc.), water bearing zones, aquifers, pemeability variations, and porosity variations are important for mine planning and in situ energy recovery processes. Features important for planning a mine will be important for planning the recovery of energy by in situ processes. Various geophysical techniques might be used to obtain the necessary geologic information. In this paper, case histories will be discussed of the use of electromagnetic geophysical surveys at a potential underground coal gasification site and a potential tar sand oil recovery site to obtain pertinent geologic information. Results show that the controlled source audio- frequency magnetotelluric technique shows promise for mapping faults and natural fracture systems when there is a sufficient resistivity contrast.

Jan 1, 1982