Search Documents

By S. Budavari, F. M. C. C. Vieira

For several decades, the deep, gold-bearing reefs of the Witwatersrand basin have been mined predominantly according to layouts characterised by longwalls with strike pillars to provide regional support. During the past few years, a new generation of mining layouts has been introduced. These layouts are based on the concept of grid-type, scattered mining with dip pillars for regional support. As the extraction of the gold reefs extends to depths below 3500 m, the hazards associated with mining at these ultra-depths are expected to increase to unacceptable levels. Therefore, the question arises as to, which of the currently applied mining layouts is most acceptable for the economic and safe extraction of an ultra-deep orebody. The purpose of this paper is to describe a research investigation carried out to evaluate the degree of acceptability, from the rock engineering view point, of four currently used mining layouts for application at a depth-range of between 3500 and 5000 m. Pendant plusieurs décades, les filons d’or profonds du bassin du Witwatersrand ont été exploités d’une manière prédominante selon des dispositions caractérisées par des longues tailles avec des piliers directionnels pour donner un support local. Les dernières années ont vu la naissance d’une nouvelle génération de dispositions de mine. Ces dispositions sont basées sur le concept d’extraction type grille, éparpillée, avec des piliers au pendage pour le support local. Comme l’extraction des filons d’or va à des profondeurs en dessous de 3500m, il faut s’attendre à ce que les risques associés à l’exploitation à ces profondeurs extrêmes atteignent des niveaux inacceptables. Par conséquent, la question se pose de savoir laquelle des dispositions de mine couramment utilisées est la plus acceptable pour l’extraction rentable et sans danger d’un gisement ultra profond. Le but de l’étude présente est de décrire les recherches exécutées pour évaluer le degré d’acceptabilité, du point de vue d’ingénierie de roche, de quatre dispositions de mine couramment utilisées pour application à un rayon de profondeur entre 3500 et 5000m. Die tiefen, goldträchtigen Riffs des Witwatersrandbeckens wurden über einige Jahrzehnte hindurch vorwiegend nach jenen Layouts abgebaut, die von Langfrontstreben mit Schlagpfeilern charakterisiert waren, um regionale Unterstützung zu gewährleisten. Während der letzten Jahre wurde eine neue Generation von Grubenlayouts eingeführt. Diese Layouts basieren auf dem Konzept der Rasterfeld-Art, gestreuter Bergbau mit Neigungspfeilern für regionale Unterstützung. Es kann erwartet werden, daß auf Grund der Tatsache, daß sich die Extraktion der Goldriffs auf Tiefen unterhalb 3500 m verlagert, die Gefahren, die mit dem Bergbau an diesen Ultratiefen verbunden sind, sich auf ein nicht annehmbares Niveau erhöhen. Folglich erhebt sich die Frage, welche der gegenwärtig angewendete Abbaulayouts für die ökonomische und sichere Extraktion eines ultra-tiefen Erzkörpers am annehmbarsten ist. Zweck dieser Arbeit ist es, eine durchgeführte Untersuchung zu beschreiben, die vom Gesichtspunkt der Gesteinstechnik gesehen, vier gegenwärtig angewandte Abbaulayouts für den Einsatz in einem Tiefenbereich zwischen 3.500 und 5.000 m evaluiert.

Jan 1, 2003

By J. P. Harrison, J. A. Hudson.

ABSTRACT: When considering the rock stress component of rock mechanics design, the basic procedure is to consider the pre-existing stress-state in the rock mass and then estimate the disturbance to this stress state as a result of engineering excavation. Failure criteria are applied to the final stress state to establish whether failure will occur. However, during the evolution of the stress state, the failure locus may be reached before the anticipated failure state and, in this case, failure will occur unexpectedly. This indicates that the complete stress path (defined as the variations in magnitudes and orientations of the stress tensor components resulting from engineering-induced or natural changes) must be considered. We list a set of stress path principles with their corollaries and then introduce a new and powerful method for simultaneously illustrating changes in the six independent components of the stress tensor. This method plots the magnitudes of the principal stresses above their orientational paths on the hemispherical projection, to provide a three-dimensional stress path locus for each of the three principal stress components. In connection with this presentational device, we illustrate a number of concepts associated with the stress path in rock engineering. For example, we show how the minor principal stress approaches zero at an unsupported excavation face, the interchange of the trajectories of two principal stresses when their magnitudes become equal, and the influence of the bounds on the principal stresses given by strength criteria. RESUME: Si on s’interesse à la composante “contrainte” lors d’un dimensionnement en mécanique des roches, la méthode de base consiste à considérer l’état de contrainte pré-existant dans le massif rocheux, puis d’estimer la perturbation à cet état générée par l’excavation projetée. Des critères de rupture sont appliqués à l’état de contrainte final pour établir si une rupture va se produire. Cependant, lors de l’évolution de l’état de contrainte, la surface critique peut être atteinte ce qui provoquera une rupture anticipée et, dans ce cas, cette dernière sera inattendue. Cela indique que le chemin de contrainte complet (défini par les variations de l’intensité et de l’orientation des composantes du tenseur des contraintes liées à des causes anthropiques ou naturelles) doit être pris en compte. Nous présentons un ensemble de règles pour les chemins de contraintes ainsi que leurs corollaires et, ensuite, nous introduisons une méthode, nouvelle et puissante, pour présenter simultannement les changements des six composantes du tenseur des contraintes. Cette méthode consiste à tracer l’intensité des contraintes principales sur le chemin d’orientation des contraintes à l’aide d’une projection hémisphérique afin d’obtenir le lieu, en trois dimensions, de chaque contrainte principale. En relation avec cet outil de représentation, nous illustrons certains concepts associés au chemin de contrainte en ingénierie au rocher. Par exemple, nous montrons comment la contrainte mineure tend vers zero à la surface d’une excavation sans soutenement, le changement de direction des deux contraintes principales quand leur intensité deviennent égales, et l’influence des conditions aux limites sur les contraintes fournies par un critère de rupture. ZUSAMMENFASSUNG: Bei ingenieurmassigen Taetigkeiten in Felsgesteinen ist es noetig die ungestoerten Gesteins Stress Componenten, die vor einem anthropogen Eingriff im Gestein vorhanden waren, zu kennen und erst dann Vorhersagen ueber Stoerung des Stress Zustandes, der durch einen ingenieurmaessigen Eingriff hervorgerufen wird, herzuleiten. Kriterien fuer das Versagen werden im letzten Stadium, des Stress Zustandes angewendet, um zu erfahren ob ein Versagen wohl eintreten wird. Es ist jedoch zu beachten, dass waehrend des Stress Aufbaus ein oertliches Versagen eintreten kann, welches vor dem eigentlichen, erwarteten Versagens Zustand auftritt. Diese Moeglichkeit weist darauf hin, dass der gesammte “Stress Path” (definiert durch die Variationen der Stress Tensor Komponenten in Richtung und Groesse, hervorgerufen durch ingenieurmaessig hervorgerufene oder natuerlich Vorgaenge) betrachtet werden muss. Wir fuehren eine Liste der “Stress Path” Prinzipien auf und stellen dann eine neue und wirksame Methode zur gleichzeitigen Darstellung der sechs unabhaegigen Komponenten des Stress Tensors vor. Diese Methode stellt die Groesse der “Principal Stresses” in Abhaengigkeit von ihrem rauemlichen Weg auf einer hemispherischen Projektion dar und erlaubt hiermit eine drei dimensionale Darstellung fuer jeden Ort des “Stress Path’s” in die drei Haupt Stress Komponenten. Im Zusammenhang mit der hier gegebenen Darstellungsart, verdeutlichen wir eine Reihe von Konzepten in der Felsmechanik. Wir zeigen zum Beispiel, wie der “Minor Principal Stress” Null zustrebt an einer Wand von einer nicht abgestuetzten Ausschachtung, den Austausch von Trajektorien zweier “Principal Stresses” wenn ihre Groessen sich gleichen, und den Einfluss der Groesse von “Principal Stresses” bei gegebenen Kriterien des Festgkeits Versagens.

Jan 1, 2003

By R. B. Khumalo, F. K. Mulenga

Sampling in a continuous flotation plant is always a challenge as these plants are meant for production and not research work. The continuous flotation operation used in this work produced three sets of data: the first was based on overall plant performance, done by sampling the feed, concentrate, and tails; the second was based on the roughers row cell-by-cell; the third set of results came from the cleaners/recleaners row cell-by-cell. The highest recovery results in all sets of data obtained lie in the particle size ranges of 40 μm and 100 μm, which is in agreement with results by other researchers in the same field. King’s theoretical (model) recovery proved to be able to fit the experimental data but there is still room for improvement as the sum of squared error ranged between 400– 1200. Data obtained in continuous flotation operation could be used with batch flotation test-work to characterize scale-up of flotation cells.

Jan 1, 2023

By A. Kapito

The ferrite-pearlite microstructure is the most popular microstructure for alloys used in structural applications, including railway wagon wheels. These alloys have been designed through alloying and thermo-mechanical processing to have a refined microstructure. Ferrite-pearlite alloys are low cost, weldable, have good fabricability, and are reliable under extreme conditions. Given these performance attributes, it seems unlikely then that their dominant position as structural steels would ever be challenged by alternative microstructures. One major achievement in the development of ferrite-pearlite steels has been in the refinement of their interlamellar spacing to very fine distances of the order of < 0.3 µm. A refined microstructure increases the hardness of the alloy, thus increasing its life under wear conditions. The interlamellar spacing in pearlitic steels has, however, been refined almost to its theoretical limit. The increasing demand for speed and increased axle loading on railway wagons requires the use of stronger, tougher, and more durable materials. This has opened the window for the development of novel bainitic steels. Bainitic alloys have a higher level of microstructural refinement than pearlitic ones. They have shown to have good wear resistance and rolling-contact fatigue resistance, and high toughness. This paper will discuss the progress to date on the development of bainitic railway wheel alloys. Four alloy chemistries have been chosen for possible further development.

Jan 1, 2012

By R. Pretorius, N. Mautsa

In a cobalt precipitation plant, phosphoric acid is used to eliminate excess uranium from the pregnant leach solution, resulting in a cobalt hydroxide product that has little uranium contamination. However, the amount of phosphoric acid added must be monitored and controlled to avoid financial and sustainability impacts and to prevent negative impacts on the final product quality. One possible solution to this problem is the use of online residual phosphorus measurement techniques to regulate the addition. By continuously monitoring the residual phosphorus levels in the solution, the plant can adjust dosing in real time to maintain the target residual phosphorus level. As a result, the cobalt precipitation plant can improve phosphorus level control, lowering the risk of overdosing, and ensuring consistent product quality. This approach can also improve process efficiency, reduce operational costs, and have a positive environmental impact

Jan 1, 2023

By J. C. D. Gush

Paper written on project work carried out in partial fulfilment of Laboratory-scale testwork was undertaken to recover oxidic copper-cobalt minerals by froth flotation, which requires maintaining a certain sulphide level in the pulp. To improve control of the sulphide concentration, an electronic closed-loop system was designed that responds to the potential output of an ion-selective electrode. The PID control was improved by adding a pre-emptive control and a self-calibration feature; a data logging facility is also included. An inexpensive valve design was incorporated using locally available parts. The operating results of this control design are presented.

Jan 1, 2005

By S. K. Lahiri, K. C. Ghanta

Design of industrial slurry pipelines is usually performed by applying semi-empirical procedures, requiring a significant experimental study for each project. The mechanisms of suspension flow are not yet completely understood and existing predictive models cover only some aspects of uniform or closely graded particle slurry flows. This paper presents a computational technique for prediction of the velocity and concentration profile in slurry pipelines based on computational fluid dynamics. This model gives numerical solutions for the concentration and velocity distributions in the pipeline cross-section. The model prediction and experimental concentration and velocity profiles were found to be in good agreement. Keywords: pressure drop; concentration profile; particle diffusivity; slurry flow.

Jan 1, 2007

By A. Fouchee, N. Naudé, K. Schommarz

"This article presents laboratory test work conducted on an African haematite ore to determine the influence of the flotation pulp pH on the final iron grade and recovery. Results show that a combination of an isodecyl ether propylene amine/amino acetate and 1,3-propanediamine, N-(3-(C10-C16-alkyloxy)propyl)-derivatives collector is suitable for separating haematite from quartz. Higher iron grades were obtained at pH levels between neutral and pH 9. This underlines the importance of the surface charge effect of the ore on its flotation characteristics. The results serve as good baseline conditions for further optimization. IntroductionBeneficiation of iron ore by flotation is widely used in Brazil, India and China. In Africa, however, this practice is not yet commercially developed.The aim of this test work is to serve as a starting point by establishing suitable pH conditions for the development of a practically implementable reagent suite, which will then be included in a larger beneficiation circuit for producing high-grade iron ore sinter feed.In the literature, African iron ore types are graded as low-grade (60.0–62.9% Fe; 8.6– 12.5% SiO2 and insolubles), high-grade (66.0– 69.9% Fe; 0.8–4.5% SiO2 and insolubles), and meduim-grade as the remaining portion (Astrup et al., 1998). The low-grade ore used in this work contains less than 60% Fe.For Brazilian ores consisting of a combination of haematite and quartz, it is common to use corn starch as a depressant and ether amine blends as collectors with additional frothing characteristic (Araujo et al., 2005). Work by Turrer and Peres (2010) shows the possibility of using other depressants successfully as well.The main mechanism of the reverse flotation of quartz from iron ore is based on the electrostatic theory of flotation. This is due to the strong pH dependence of the zeta potential of the mineral edge planes on silicate particles (Fuerstenau and Pradip. 2005)."

Jan 1, 2016

By E. C. Stoltz

Note: An electric tin smelter for the processing of Iow-grade tin concentrates in South Africa by E. C. STOLTZ, Pr. Eng., B.Sc. Eng. (Rand) Gold Fields of South Africa Limited is the largest producer of tin in the form of concentrates in South Africa, more than 55 per cent of the South African tin production being produced by the tin mines of the Group. Most of these concentrates are exported to be custom-smelted in overseas smelters, but the modern tendency is for tin-mining countries to establish their own smelters.

Jan 11, 1976

By F. Lanaro, K. Röshoff, R. Christiansson, L. Jing

This paper presents the results of a project for developing a methodology for empirically determining some of the mechanical properties of the rock mass at the Äspö Hard Rock Laboratory, Southern Sweden. Using the equations available in the literature, the deformation modulus, friction angle, cohesion and unconfined compressive strength of the rock mass were estimated. A comparison of the results using different classification methods (Q, RMR, GSI, RMi, Ramamurthy’s) was made to estimate the range of variations in the mechanical properties with the considerations of: i) the quality/quantity of the geological data; ii) the technique for partitioning of the rock mass into homogeneous domains; iii) the sensitivity and subjectivity of the empirical methods; and iv) the need for validating the empirical methods against a test case. Cet article présente les résultats d’un projet visant à établir une méthodologie, pour déterminer, de façon empirique, les propriétés mécaniques de la masse rocheuse. En utilisant les corrélations disponibles dans la littérature, quelques-unes des propriétés de la masse rocheuse ont pu être déterminées (module de déformation, angle de friction, cohésion, force de compression illimitée). Une comparaison des résultats obtenus par différentes méthodes (Q, RMR, GSI, RMi, de Ramamurthy) a permis d’établir une échelle de variations des propriétés mécaniques et de formuler une série de recommandations concernant : i) la qualité/quantité des données géologiques ; ii) la technique de partition de la masse rocheuse dans des domaines homogènes ; iii) la sensibilité et la subjectivité des méthodes empiriques ; iv) la nécessité de valider les méthodes empiriques à l’aide de nouvelles études de cas. Dieses Paper präsentiert die Ergebnisse eines Projekts mit dem Ziel, eine Methodik für die empirische Festhellung von mechanischen Eigenschaften im Gesteinmassiv zu etablieren. Durch Verwendung der in der Literatur zugänglichen Korrelationen, wurden einige Eigenschaften des Gesteinmassivs festgestellt (Entstellungsmodul, Reibungswinkel, Kohäsion, unbeschränkte Kompressionsstärke). Ein Vergleich der Ergebnisse unterschiedlicher Methoden (Q, RMR, GSI, RMi, Ramamurthy’s) wurde durchgeführt und dies erlaubte die Feststellung der Variationsskala von den mechanischen Eigenschaften, sowie eine Reihe Empfehlungen für: i) Qualität/Quantität der geologischen Dateien; ii) die Technik für Teilung des Gesteinmassivs in homogene Domäne; iii)die Empfindlichkeit und Subjektivität der empirischen Methoden; iv) das Bedarf die empirische Methoden gegen neue Fallgeschichten zu validieren.

Jan 1, 2003

By P. F. Sorensen

A simple mathematical model is presented that relates the &apos;head&apos; developed at the surface of pulp in a tank to the power dissipated by the air in producing it. The value for the head is then used in the calculation of the superficial circulating velocity of the pulp and the area of the overflow, and the product of these two values gives the pumping rate of the pulp. Thus, the superficial circulating velocity, and hence pumping rate of the pulp, are related directly to the flow-rate of the air. This hypothesis was tested with good results in an air-agitated pachuca tank (of 1 m in diameter) fitted with a draught tube. The method can also be used for the prediction of the pumping rates in production-scale vessels.

Jan 1, 1985

By J. M. Stewart

The purpose of my few comments is to try to create a healthy perspective to constructively link considerations of the sessions to follow to those of the earlier sessions. I propose to do this by considering some of the issues and priorities related to the development of backfill systems and technology for South African gold mines.

Jan 1, 1988

By C. E. Dohm

The paper serves to show the importance of both a geological model and geostatistical model that support one another in mineral resource evaluation. It highlights the advantage of reference models for the geometry, the geological, statistical and geostatistical models of various orebody types and introduces a method for quantifying the combined uncertainty in these models. The example presented reveals how the above levels of information can be applied to add value to a resource evaluation process. It is a generic example in that it is the technique of combining uncertainty in the geological model (boundaries) as well as the grade model to assess the overall risk in the estimation of the resource. Data from the coal industry is used to illustrate the techniques. The geological uncertainty is considered via categorical simulations and these are combined with simulations of the variables (grades, thickness,) being estimated in the resource. The simulation techniques used are based on the application of GSLIB software1and a general discussion of the two simulation processes is included. In conclusion the paper demonstrates how the results of two types of conditional sequential simulation can be combined to produce confidence limits that take both uncertainties into consideration. This technique does not replace the resource estimation; it serves as an additional tool to quantify confidence in the resource evaluation model. The topics considered in this contribution are in terms of continuous improvement of mineral resource evaluation.

Jan 1, 2003

By R. J. Davidson, M. V. Nkosi, V. Veronsee

When activated carbon is used for the recovery of gold and silver from Witwatersrand gold-plant solutions, severe fouling of the carbon by calcium carbonate is experienced. Also, difficulty is encountered in the retention of the adsorbed silver on the carbon because it is displaced by gold. The acidification of plant pregnant solutions before they are contacted with carbon was therefore investigated as a means of overcoming these shortcomings. The results from batch laboratory experiments on the effect of pH on gold adsorption from plant solutions and from synthetic solutions of high ionic strength indicated reaction rate optima in the region of pH 5 and below pH I. The effect of pH on the equilibrium capacity constant for gold adsorption onto activated carbon was also studied, using both a plant solution and a synthetic solution of high ionic strength. In the case of the plant solution, the results suggested only a marginal change in carbon capacity for gold in the pH range 12 to 6, with significant increases in capacity at lower pH values. In the case of the synthetic solution of high ionic strength, the capacity constant was found to increase steadily as the pH was lowered from 12 to I. It was also found that the gold adsorption capacity of the carbon was significantly better for the synthetic solution. No precipitation of gold from the pregnant solution (gold content approximately 6 g/t) was noted as the pH was decreased to values as low as ,. However, about 25 per cent of the 0,6 g/t silver content was found to have precipitated when a pH value of 3,0 was attained. Further substantial precipitation of silver took place as the pH was lowered further. The investigation was extended by the passing of suitably acidified gold-plant solutions through one or more columns containing activated carbon. Preliminary results showed that the particle size of the carbon had a significant effect on the rate of gold adsorption. No displacement of adsorbed silver by gold was observed to take place at an influent pH of 5. In a typical continuous &apos;merry-go-round&apos; operation involving three columns in which gold was eluted from the lead column every 48 hours, effluent values averaging 0,001 g/t gold could be consistently achieved under simulated plant-operating conditions. The results were obtained at relatively high velocities of influent solution, resulting in very little hold-up of gold in the carbon-recovery circuit. More than 99,9 per cent of the gold and more than 99,8 per cent of the silver was recovered in the adsorption circuit, while the elution data indicated an average elution recovery of 99,8 per cent of the adsorbed gold and 98,2 per cent of the adsorbed silver. Elution of the carbon was carried out at 91 QC. This involved pretreatment of the carbon with a sodium cyanide solution, followed by elution with deionized water. At a loading flowrate of 66 bed volumes per hour, the indicated take-up of metals on the carbon in the lead column was as follows; 53 k g/t gold, 6 k g/t silver, 57 k g/t copper, 14 k g/t nickel, and I k g/t zinc. Only a trace of cobalt was adsorbed. At an elution rate of 1,7 bed volumes per hour, the lead column was found to be completely stripped in under 5 hours, with concentrations of gold in the eluate reaching 6 to 7 g/l. Besides the excellent adsorption and elution results obtained when acidified pregnant solution was used, no fouling of the carbon was indicated, and the pressure drop across the three columns was considered to be well within practical limits. When compared with conventional zinc precipitation, the carbon process would appear to have considerable economic merit, with strong indications that significant savings would be possible both in capital and operating costs. Further pilot-plant experiments, preferably on a gold plant, would be required before a meaningful cost comparison could be made with the existing process.

Jan 1, 1979

By B. J. Pieters

The paper describes the difficulties experienced with inferior coking coals as Iscor began using larger blast furnaces for the production of liquid iron. Research conducted at Iscor from 1977 to 1979 showed that benefits could be gained from the use of partially briqueted charges, and it was decided to install briqueting plants at the Vanderbijlpark and Newcastle Works. Details are given of the later plant, which was supplied by a consortium consisting of Voest Alpine, Didier Engineering, and Sumitomo Metal Industries. Sumitomo also supplied information on the optimization of coke quality along the lines of their Sumicoal System. The results have been a marked improvement in coke quality, much better blast-furnace operation, and increased productivity.

Jan 1, 1991

By J. M. Stewart

Although the incidence of heat stroke in South African gold mines is small, work continues on its reduction. This paper proposes limits of heat stress that are applicable to South African underground conditions, with the warning that they should not be extrapolated to other situations without careful consideration having first been given to their limitations. These limits of heat stress take physical and physiological considerations into account, and they correspond to there being a 10-6 risk of an essentially nude man developing a rectal temperature in excess of 40°C. It is recommended that further work should be undertaken on the development of equations for the calculation of the heat transfer from clothed men, the derivation of equations that quantify the physiological conductance and sweat rate response of humans, and on establishing the frequency distributions that describe variations in rectal temperature response between individuals in different types of environment.

Jan 1, 1981

By C. Norden

The purpose of this article is to show how a representative overall equipment effectiveness (OEE) measurement can be calculated for an underground coal mining bord and pillar batch process. The calculation method, the typical losses (which include planned and unplanned availability losses, coal quality losses, and process rate losses) and the underlying logic are presented and discussed. It is argued that the current traditional underground bord and pillar mining process can currently provide a maximum theoretical OEE of only 49 per cent, while a realistic benchmark target should be in the order of 37 per cent, which relates to an average of 2400 t per shift or 1.2 Mt/a. In addition, it is argued that the current bord and pillar process is the current bottleneck to further improvement past the 2400 t per shift benchmark, and that fundamental process changes will be required to eliminate this bottleneck.

Jan 1, 2012

By F. R. Deist, R. P. Plewman

Discussion: A. Hazell (Associate Member) and T. J. Kotze (Graduate Member): The authors must be congratulated on the development of a versatile computer programme for determining the stresses and displacements resulting from mining operations. As a design tool it will no doubt take its rightful place together with the analogue computer. Union Corporation made use of this digital computer programme whilst still in its development stage to determine the stress distributions which were causing the unexpected failure of the Marievale sub-incline shaft. Two features arising from this investigation may be of interest to members, namely: A. The solution to the problem of stabilizing a rectangular inclined shaft, which turned out to be contrary to accepted mining practice, and B. A comparison between the results obtained with the pure digital system and the analogue computer. A. The shaft is nine ft high and 20 ft wide, dipping at 9° to the horizontal and crossing the bedding planes. Fig. 1 is a plan and Fig. 2 is a section of the sub-incline shaft pillar area showing the relative positions of the shaft and reef as well as their respective dips. The deepest point in the shaft is 3 300 ft below surface and the requirement of a stress free ground surface may not be satisfied. It also means that the original gravitational stresses are low. A 900 ft wide pillar was left to protect the bottom section of the shaft, the top section being understoped years ago. Extraction of the pillar was started at the beginning of last year, mining operations being carried out in the accepted manner, starting beneath the shaft and mining outwards. The approach did, however, turn out to be the wrong one, because failure of the shaft was noticed soon afterwards. Even small movements were serious in this case due to the low clearance between the skips and the shaft supports. During October, 1968, failure between benchmarks 8 and 10 (see Fig. 1) became so excessive that hoisting speeds had to be reduced. Failure continued to occur and, by the end of March, 1969, failure had propagated up the shaft as far as benchmark 7, and down as far as benchmark 12. As this shaft had a tight hoisting schedule it was imperative that a quick solution be found to arrest the failure.

By M. Getz, G. Asbjörnsson, M. Evertsson, E. Clausen

The mining and minerals processing industry is gradually being digitalised to improve efficiency and reduce waste. One aspect of this transition is to ensure that relevant process-data in sufficient quality and quantity is given to the operator in the right format and at the right time to improve decision-making. Augmented reality (AR) can serve as a potential ICT-based support tool for human operators to achieve this goal. With AR, virtual information is combined with the real world in real-time. Therefore, AR technology has the potential to fulfil the need for improved data visualisation in Industry 4.0. This article is the result of a collaborative effort of Chalmers University of Technology and RWTH Aachen University to identify selected state-of-the-art applications of AR that are currently being applied in the mining and minerals industry or selected related industries. This paper aims to show opportunities for the application of AR in the mining and mineral processing industry with selected conceptual applications. This paper concludes with several requirements identified as necessary to implement the conceptual applications of AR in the mining and minerals industry. Keywords: Augmented reality, mining, mineral processing

Jan 1, 2020

By J. E. Furze

World-wide hikes in the oil price and the prospect of future scar cities of liquid and gaseous fuels have given enhanced status to the South African coal industry. It is thus understandable that the colloquium held at Wit bank on 3rd and 4th October, 1979, and organized jointly by the South African Institute of Mining and Metallurgy and the South African Coal Processing Society should have attracted more than 400 delegates.

Jan 1, 1979